How to Access Device from Web

This guide is valid for models 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16.

When devices are connected to the network, they can also be accessible from a computer. The first thing you need to make sure of is that the computer you are using and the DVR/NVR are connected to the same network (network is coming from the same router for both devices). You will first need to obtain the IP address of the DVR/NVR from Menu → System → Network → IPv4 address.

After noting the IP address of your device, open Internet Explorer and in the address search bar type in the DVR/NVR IP address. If the NVR and the computer are on the same network then it will pull up the login page of the DVR/NVR. The credentials will be the same as when you log into the local interface of your device.

2M DVR XVR Setup and User Guide

Read Also : Easily Connect IP Cameras Over Existing Coaxial Cabling

.

How to Find the Serial Number Using 2M Tool

Click here to download 2M Tool

2M Tool is used to find the IP address of your 2M NVR, DVR, or IP camera, as well as limited management of its settings. You only need to make sure that the computer you are using 2M Tool on is connected to the same network as the device that you are trying to search for.

Why do we need the serial number? The serial number is mainly used in case of a customer needing a password reset on their device.

How do we find the serial number? There are a few ways to find the number:

In the case that you forget the password for you device in which you will not be able to access the web page, and the camera is too high up to reach to find the sticker, you can use 2M Tool to find the serial number. 2M Tool does not automatically show the number; you must force it to show. First, you will need to click on the Settings icon to show the options:

Then another window will open where you can select Serial Number to show.

Once you hit OK, the serial number will then appear.

How to Install Plugin for Internet Explorer

This article features screenshots from our 2MN-8XXX series NVR and our 2MT-4XXX series DVR, but the same principle will apply to any other recorder. This is because each recorder requires a plugin in order to view the cameras on the web page. You will have to manually install the plugin, but it is usually always provided as a link for easy access.

First, you must make sure that you are using Internet Explorer. Internet Explorer is the only browser that can support these plugins. It is possible for some devices to be viewed on Google Chrome or even Firefox, but then other functions are very limited so it is highly not recommended to use those browsers. Once Internet Explorer is open, and you navigate to the device’s web page by entering the IP address, there should be a link shown on the page. You can see on the picture below that the link is located on the top of the page.

When you click on the link, a pop-up will appear on the bottom of the page that will let you choose whether to Run the program or Save the program onto your computer. Note: Running the program will not save it. If you wish to save the program, please select Save. Once it has finished downloading, then you can run the program from the file location.

If you choose to Run the program, an error message will appear noting that the publisher couldn’t be verified. This is no issue; the plugin will not cause any harm to your computer. Hit Run, and run the installation. Some installations will require you to close out of Internet Explorer in order to complete the setup.

Once the setup is complete, refresh the page, and another message will pop-up on the bottom that asks you to Allow the add-on to run. Select Allow, and log into the page. Now you should be able to view your cameras on the web page.

.

How to Set Up 2M Guard

2M Guard is the phone app that we use for our NVR’s to view cameras from our phones offsite.

This app only works for models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

2. Two ways to add a device onto the app:

Method 1: Adding Device Through Star4Live

Method 2: Adding Device Directly on the App

How to Set Up 2M Station

2M Station is the PC software to view your cameras on your computer on and offsite. This program only works with models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16, and our IP cameras

When first running the program, it will prompt you for a username and password which will be admin/123456 by default. It is recommended that you change the password after installation.

Once you are logged in it will show the menu. Click on Device Management to add any devices. On the left side make sure that Encoding Device is selected. It will show at the bottom of the screen any devices that are online as long as the computer is on the same network as the devices.

There are two methods to add an online device. The first method is fairly simple. All you need to do is check the box for the NVR that shows under Online Device and then click Add. The second method to adding an online device is to manually add it. First click on Add next to Managed Device, and it will open another window where you can input the details of your device. It will ask for:

After putting in all of the correct information of your device, click on Add and then the device should come online.

Another method to add a device is by using the P2P method which allows for a user to view their cameras offsite from any location. The device will be added as a Cloud Device instead of an Encoding Device.

It will show Login and Register buttons that will link to your Star4Live account which will show the devices you have previously added. After logging in, it will take a minute or two for the devices to show online. At first, it will say Offline (Connecting…), but eventually the status will show Online.

After successfully adding all of your devices, go back to the menu and click on Live View to view your cameras. A list of online devices will show on the left side of the window. Click and drag the device into the window view in order to load all of the video. If not all of the cameras are wanted in view, you can click on the plus sign next to your device and it will show a list of cameras connected to the NVR. You can click and drag specific cameras onto the live view screen.

.

How to Set Up Email Notifications Using Gmail

This is valid for models 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, and 2MN-8232-P16.

Gmail will have automatic security settings that need to be disabled before configuring email settings in the NVR. You will need a computer in order to edit these settings. First, log on to your Gmail account and then click on the square icon in the upper right corner of the page. Click on Account.

Security → Scroll to the bottom until you find “Less secure app access” → “Allow less secure apps: ON”

Now that Gmail has been set to allow app access, we can move on to the NVR settings. These can either be configured through the web page or through the NVR itself.

Through the DVR/NVR: Main Menu → Network → Basic → Email

Through the webpage: Setup → Network → Email

After you finish entering all of the settings and the test is successful go to Camera → Motion → Select Camera → Trigger Actions → Send Email

.

How to Share a Device

This is only valid for models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras

Each NVR can only be added by one account at a time, so if one wants to add a device onto multiple accounts they would need to share the device with one account being the “main” account. This means that one person will have the device added to their account and that person will share the device with other people. Each person still must have their own Star4Live account.

How to share the device is simple. First, you will need to log onto the main Star4Live account which the NVR has been added to. It can be done either through the computer or your personal phone.

Sharing from Computer: after logging into the account your list of added devices will appear. Click Share on the row for the device you are wanting to share.

Then a menu will appear to enter the account you want to share to, the Valid Till date, User Rights, and any Description you want to give.

Once all of the information has been correctly filled out, click Confirm to successfully share.

Sharing from 2M Guard Phone App: after logging into your Star4Live account on the 2M Guard app, go to your Devices and then tap on the device that you want to share. A small menu will appear. Then tap Share on the bottom of the screen.

The next window will show the device and a list of the cameras that are connected and online. You can choose specific cameras, or select the device so that the entirety of its cameras are selected for sharing.

Once your device(s) has been selected, the Share menu will finally appear. The app will ask for the same information as the computer does, but it will not give a space to fill out a description. Fill out the Share To and the Valid Period the same as you would do on the desktop instructions written above. The only other difference between the Star4Live browser and the app is the sharing Type: you will be able to choose between Role or Function.

NOTE: Only admin rights will allow another user to access the device through the web browser or through 2M Station because they both allow a user to make changes to the device. If you do not wish for another user to be able to make any kind of changes (viewing only), please choose the By Function type.

Once one of these methods have been completed to share the device, the recipient only needs to log into their Star4Live account and the shared NVR should show automatically under their own device list.

How to Sign Up for Star4Live Account

Star4Live is the server that we use to view NVR and camera footage over the web. Each customer needs to have an account to view and manage their devices.

This is only valid for models: 2MT-4004, 2MT-2008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

How to Upgrade the Firmware

This article applies to the models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16.

Every now and again, we will release a new firmware update that can either hold new features for your unit, bug fixes, or a bit of both. We have made it simple to request the newest firmware so that there is no need to wait for a file to be sent. First, you will need to make sure that your device is connected to the internet so that the NVR will be able to communicate with our servers.

Method 1: From the NVR Interface

Then you will go into the Main Menu and click on Maintain. There will be a section for Upgrade.

There are two options for upgrading:

You will most likely want to choose the Cloud Upgrade option unless you have received the firmware file from Tech Support beforehand. Click Cloud Upgrade, and wait for the device to finish its search. It will either notify you that the current version is already the latest, or it will show a newer version, and the Upgrade button will highlight at the bottom of the screen.

The upgrade time will vary between 1-5 minutes, sometimes lasting longer depending on the size of the update. Once the update has finished, the device will automatically restart. It will be ready to use again once it has fully finished the reboot.

Note: Please make sure that the device does not disconnect from the network or from power because it can cause a risk in damaging the unit if there is a failed update.

Method 2: From the Web Interface

The NVR can be updated from its web page if there is no monitor connected to the unit, or if it cannot be physically accessed. From the web page, you will navigate to Setup → Maintenance → Maintenance → Cloud Upgrade → Detect or Check for Update. The process is the same as it is from the unit itself, and the same rules will apply.

How to Use Star4Live

Star4Live is the server that we use to view NVR and camera footage over the web. Each customer needs to have an account to view and manage their devices. You must use Internet Explorer in order to access all of the functions of Star4Live.

This is only valid for models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

What software do I use to view my cameras on my PC, and where can I download the software?

2M Station: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16

Windows Download Link
MAC Download Link

What phone app do I use to view my cameras?

.

Safety cautions

Product overview

DVR

Camera

Power Cable Splitter

BNC Cable

Xmeye Dvr System Instructıons For Use

Read Also : Camius devices troubleshooting

Hard Drive Installation

IMPORTANTTo record videos and play the historical videos, the installation of the Hard Disk Drive is a must.
Otherwise,you can only watch the live video.
This DVR system works with a 3.5” SATA Hard Drive.The Hard Drive should be formatted after it’s installed.×Dismiss this alert.

System Connections

IMPORTANTDo not fix the AHD camera before you can view the image on the monitor and confirm the ideal position to install it.×Dismiss this alert.

1.Plug a power adapter into the DVR and the socket to power on the DVR.

2. Connect a monitor to the HD Output or VGA Output on the DVR with an HDMI cable or VGA cable (not included).

3. Connect the Ethernet Cable with the DVR and your router.

4. Connect the AHD camera with the BNC Cable.

5. Connect the Yellow Video Connector to the BNC Video Input on the DVR, and connect the Red Power Connector to the Male Connector of the Power Cable Splitter.

6. Connect the Female Connector of the Power Cable Splitter with another power adapter. Then plug the power adapter into the socket to power on the camera.

Operate dvr system with a monitor

Startup Wizard

After connecting the DVR and cameras to power, wait for 2-3 minutes. A Startup Wizard will start to guide you via a series of pop-up windows.

Connect the USB mouse to the DVR, then click Next until you see the window of Time-Language Configuration.

1.Select the time zone, date format, time format, language, and set the time for your DVR system.

2. The default password is empty, please reset it for your DVR following the tip.
The new password should be more than 6 digits and use the combination of numbers and letters to ensure your system’s security.

3. Select safety questions and enter the answers for resetting the password if necessary.
You can also enter your email address for getting the verification code to reset the password.

4. Check if the network connection status is normal. If not, you can configure it by clicking Network.

5. Scan the QR code to get the Serial Number of your DVR system and download the App named XMEye into your mobile device.

6. Before fixing the cameras, you can log in to XMEye App to check the live view to confirm the ideal position.

7. Detection based on human shape is enabled by default.
The DVR system will send alerts to your mobile device when there is human shape detected by the cameras.
Please refer to the section of Motion Detect the detailed setting.

IMPORTANTClick Next and OK to exit the wizard. You can right click on the screen, then go to Main Menu > Startup Wizard to bring it up again.
If the wizard is no longer needed, just check the box before Don’t Display the Wizard again on the first interface of the Startup Wizard.×Dismiss this alert.

Live Video

You will see the live videos from the AHD cameras in split-screen mode (9 screens by default) after exiting the wizard.

※ Move the mouse cursor to the live video of any channel, some icons may be displayed according to the setting.

Notes:

1.The icons of and are displayed by default, while for icon , and , please right click andgo to Main Menu > Alarm (see on page 15) to enable them.

2. If you want to loop to display the live videos from some certain channels in full-screen mode, please go to Main Menu > System > Tour to enable this function.

3. For viewing the live video from one channel in full-screen mode, please move the mouse cursor to the desired channel, then double click. To exit full-screen mode, double click again.

Hard Drive Formatting

When you receive the system, the system has a pre installed hard disk, which does not need to be formatted,but if you have to replace another hard disk, it needs to be formatted at first ,then it can be used normally Install the Hard Drive first, then right click and go to Main Menu >Advanced > Storage to check if the type is Read/Write or the status is Normal.

If not, please click Format Storage to start formatting your Hard Disk Drive.

Video Recording

Right click on the screen, then go to Main Menu > Record > Record Conf. to set the record mode and record plan.
This DVR is set to record videos 24 hours a day by default.

Channel:

Select the channel to set the record mode and plan. You can select a single channel or all channels.

Redundancy:

Installing 2 pieces of Hard Disk Drive is required when enabling this function, and HM245 doesn’t support it.

Length:

Set the maximum video length of each recording from 1 minute to 120 minutes. It’s 60 minutes by default.

PreRec:

The camera will start recording a video around 5s before it detects the motion or human shape.

You can reset the time from 1s to 30s, but the accuracy of the pre-recording time may be affected by the bitrate.

Mode:

Set the recording mode and the options are Schedule, Manual and Stop.

Record Plan:

Set the recording schedules.

Notes:

The oldest video will be overwritten by the latest one by default when the Hard Disk Drive runs out

of space.

Video Playback

Right click on the screen, then go to Main Menu > Record > Playback to play the video recorded.

You will see the different playback modes in the pop-up window of Play Mode.

Explanation of playback modes

1.Common Playback

Select the channel(up to 4 channels at the same time), a period and a date on Blue background to

play all types of videos recorded.

1. Area for Video Playing
2. Playback Buttons
3. Timeline
4. Channel
5. Filters
6. Filtered Videos List
7. R: Standard Videos
8. M: Videos recorded when the camera detects motion or human shape.
9. Detailed Info. of the Selected Video
10. Search
11. Show/Hide Filtered Videos List
12.Timeline by Hour/Minute

TipFilters will not be available after you left click on the timeline, but you can exit this mode and re-enter to select the filter.×Dismiss this alert.

Option 1 :

Left click on the Green/Red (Green for standard videos recorded, and Red for the videos recorded whenthe camera detected motion or human shape) part of the timeline of each channel to play the historical videos.

Option 2 :

Left click on the live video of one channel, show the filtered video list, then double click on the selected video to play it.

Description of Playback Buttons

Left click on the live video of any channel, then start using the buttons to control the video playback.

Tips:

① You can click the icon to cut a video, then click to back up to the external storage.

② Previous Frame and Next Frame work only when pausing the video.

③ The speed of Fast Reverse and Fast Forward will be displayed on the right end of Playback Buttons.

2. Sync Playback

This function aims to put the videos from different channels at the same time to compare.

Select 2 channels at least ( up to 4 channels), a period and a date on Blue background to play the historical videos simultaneously at the selected time on the same timeline.

3. Dayparting

This function aims to put the videos from the same channel but at different time to compare.

Select a channel, number of split screens, and a period to play the videos recorded from this channel on different timelines.

NotesYou need to press and hold the left mouse and move on the bar of Period to select time period.×Dismiss this alert.

4. Smart Express

Select one channel or all channels, then select the speed of Fast Playback, the system will play all the videos recorded with the speed you selected.

5. Smart Search

Select one channel and a time period, then check the box before Detect and select a date on Blue background to play the videos recorded when the camera detected the motion or human shape.

※Double click the thumbnail to play the related videos.

6. Face Search

Select one channel, a time period and a date on Blue background to play the videos recorded when the camera detected faces.

Video Backup

Step 1:

Insert the USB disk into the USB port of the DVR system. Right click on the screen, then go to Main Menu >Record > Backup to start.

Step 2:

Select your USB disk, then click Backup to bring up a pop-up window.

Step 3:

Select Channel, Start Time and End Time, then click Add to display all the filtered videos.

Step 4:

Check the box to select the video files and Backup format, then click Start to back up the videos.

Tips:

① The format of the USB Drive should be FAT 32.

② An alternative solution to back up the videos is listed below.

• Go to the interface of video playback and click to show the filtered video list.

• Check the box to select the videos.

• Click to start backing up. The next steps are the same as the first solution mentioned above.

Snapshot Setup

The system will capture the snapshots 24 hours a day when the camera detects motion or human shape.

Go to Main Menu > system> SnapShot Conf. to reset the time interval of capturing a snapshot, and set up the schedules when the camera will capture a snapshot as well.

Alarm

IMPORTANT:

The alarms of Motion Detect and Human Detect are enabled by default. If you need to record videos whenthe camera detects the face or gets blocked as well, please enable Face Detection and Video Blind.

Please go to Main Menu > Alarm to set the alarm you need.

Motion Detect

The camera will start to record videos when it detects motion.

Channel:

Select the channel you’d like to enable motion detection.

Enable:

Check the box to enable motion detection.

Sensitivity:

If you select higher sensitivity, the camera will be more easily to be triggered to start recording videos. It’s advised to select Middle to balance the accuracy and effectiveness of the alarm, thus reducing the false alarms.

Region:

Click Set, then press and hold the left mouse to drag and select the area for detecting. The pink area indicates the selected area.

Period:

Set up to 4 time periods for each day to send the alerts when the camera detects motion.

MD Interval:

Set the time interval of two alerts. It aims to decrease the frequency of the alerts caused by the same moving object.

Record Channel:

The selected channel(s) will start recording when the current channel detects motion.

Tour:

The display will loop to display the live video from the selected channel(s) in full-screen mode when the current channel detects motion. You can go to Main Menu > System > Tour to set the time interval to show the live video in full-screen mode.

Snapshot:

The selected channel(s) will capture a picture when the current channel detects motion.

PTZ Activation:

The cameras don’t support this function.

PostRec:

The camera will remain to record the video around 10s after the motion or human shape detection ends. You can reset the time from 10s to 300s.

Show Message:

After enabling this function, the display will pop up a window to show the Alarm Status for all kinds of alarms when the cameras detect motion, human shape, or more.

Send Email:

Before enabling this function, please go to Main Menu > System > NetService, then double click on EMAIL option to set up your email address to receive the alerts.

Write Log:

The logs of the alerts will be written into the system once you enable this function. You can go to Main Menu > Info > Log to check the detailed log information.

FTP upload:

The system will send the videos recorded or snapshots captured to the FTP server you set when the camera detects motion. Please go to Main Menu > System > NetService, then double click on FTP option to set up your FTP server.

Mobile reported:

The system will send alerts to your mobile device when the camera detects motion. Please install the App and add the DVR to the App following the section of OPERATE DVR SYSTEM ON MOBILE DEVICE on page 18.

Up-to-Coaxial Control

Right click on the main menu and select XVI control to start setting up your camera.

※If the live video from the camera is mirrored or flipped, you can check the box before Mirroring or Overturn to fix it.

※If you set something wrong, please click Restore to get back to default settings.

.

NotesFor the setting of alarms like Video Blind, Video Loss, Human Detect and Face detection, please refer to the settings of Motion Detect. If prompting Video Loss, the DVR will not record videos, but only to send alarms.

TROUBLESHOOTING

The DVR System Boots Up Abnormally Or Reboots Automatically.

If the issue persists, please contact Support for more help.

.

How Should I Do If I Forget My Password?

• Please click Forgot Password when logging into the DVR system.

• The system will ask you the security questions you set in the Startup Wizard, please enter the right answer to reset your password.

• If you forget the answers, click Forget Answers to enter the interface of Verification Code.

• Launch XMEye App,tap > FIND PWD on an Android device or tap Forgot your device password?(on the interface of Add Device) > FIND PWD on an iOS device to scan the QR code on the left side to get a verification code, then enter it into the box on the interface of Verification Code to reset your password. However, if you set an email to get the verification code in Startup Wizard, the App will send the code to that email. You need to get it from email, then enter it on the interface of Verification Code.

.

How Long Can A Hard Disk Drive Record For This DVR System?

There are 4 AHD cameras connecting to this DVR system by default. These cameras are with the resolution of 1080P and variable bitrate which depends on the surveillance scenes. If the bitrate is around 2Mb/s, the corresponding size of the video file will be around 21G per day.

As a result, a Hard Disk Drive with the capacity of 1T may record around 12 days.

.

How Can I Connect An Extra Camera With The DVR System In Addition To The 4 Cameras In The Package?

DVR system supports up to 8 cameras to be connected. Please contact Hiseeu to get the same type of cameras and the corresponding cables.

If you just have a camera in hand, please follow the steps below:

For the camera with the format of TVI/CVI/SVI/CVBS, right click on the screen, select XVI&AHD to set the Signal of the channel to Auto or the corresponding format of your camera, then connect the camera with the DVR system.

For an IP camera, please go to Main Menu > System > Digital > ChannelType to check the box of the fourth line, then go back to the main screen and move the cursor to the channel you’d like

to connect the camera.

Click in the center of the screen to start adding the camera.

.

The Image From The Camera Is Upside Down.

Right click on the main screen and click XVI Control, then check the box before Mirroring or Overturn to flip the image.

.

What Should I Do If It Runs Out Of The Space On Your Hard Disk Drive?

The DVR system is set to loop recording by default, which means the latest videos will overwrite the old videos automatically when it runs out of the space on the Hard Disk Drive.
You can back up the important videos, then delete the videos or format the Hard Disk Drive.

.

Why Does The Hard Disk Drive Stop Saving Videos?

.

The App On My Mobile Device Cannot Receive Snapshots When The Camera Detects Motion, Human Or The Camera Gets Blocked, Etc.?

The App can receive the snapshots by default and you can check from Alarm Push/Alarm of the App.

.

Why Does The App Remind Me Of “Maximum Video Link”?

For remote viewing, such as from App or PC Client, you can only simultaneously access the live videos from 6 channels at most. Please close the unnecessary channel.

.

Why Doesn’t The PC Client Watch The Live Videos?

.

Why Doesn’t The PC Client Watch The Live Videos?

.

What Should I Do If I Got Too Many Push Notifications From App?

This DVR system can support to send you alerts when the camera detects motion, human, face, video feed loss,or the camera gets blocked. You can go to Main Menu > Alarm to disable certain kinds of alarms to reduce alerts.What’s more, you can lower the Sensitivity, set the Region and Period to reduce alerts.

.

How Can I Modify The Time Stamp And Channel Name Displayed On The Screen When Playing The Videos Recorded?

You can go to Main Menu > System > Display to select the channel you’d like to set, then enable Time Display and Channel Title, then click Set. You can even drag them to your desired position on the screen.

.

.

 Specification Sheet – NVR – LV-N9508Q8E

 Specification Sheet – Camera – LV-PBK80804C

 Quick Start Guide – NVR – LV-N9508Q8E

 User Guide – NVR – LV-N9508Q8E

 Firmware – NVR – LV-N9608C8E LV-N9616D6E v3.5.31

 Client – LaView Net Client for Windows

 Client – LaView Net Client for Mac

 Video Player – VSPlayer for Windows

 Video Player – VSPlayer for Mac

 IP Portal – IP Search Portal (SADP) for Windows

 Plugin – Web Component for Safari / Mac

 Technical Support Articles

.

How do I connect my TVI system to my phone app?

Please follow these steps to setup your mobile device. You can watch the YouTube videos and follow along or follow the instructions bellow.

IPhone:

https://www.youtube.com/watch?v=zshaTac0ka8

Android:

https://www.youtube.com/watch?v=G1DtkrYLIas

LaView NET app:

*If using 4G/LTE with bad signal, you may not obtain a picture. Attempt using a strong signal.

LaView DVR User Guide

Read Also : Camius DVR installation and user guide

.

How do I download videos off my TVI System?

To download video footage you’ll need a flash inserted into one of the USB ports on the system. Then go to Main Menu>Export>Normal. Once in the exporting page, you’ll need to select the channel the video was recorded on along with the starting time and end time to search for footage.

Then click on “Search” at the bottom and you’ll have some video previews show up. You can select any of the previews and play it on the top right hand side. When you know what files you’ll need check mark the box on the upper left hand corner of the preview window and click on “Export” at the bottom. Once the export is done, you’ll now have all the files on your flash drive.

How do I format my HDD?

To format your HDD you’ll need to go to the Main Menu>HDD>General. Once in the HDD menu, check mark the box to the left-hand side of the HDD information. Then click on “Format” or “Int” at the bottom. Please note this will delete all information off the HDD.

How do I playback my recordings?

To playback videos go to Main Menu>Playback>Normal. In that section choose your camera(s) on the right-hand side. Then double click any of the days on the calendar with either a dark blue or red on them. This should automatically start playback for that day. Use the bar at the bottom to jump to a specific time during that day.

I have everything plugged in, but all I see on my screen is “No Video”

The system should automatically pick up cameras once they are connected and have power. Be sure to check the power source for the cameras. If the power is connected correctly there may not be enough power be supplied. Cup your hands over the lens and if the IR lights turn on, then the camera has enough power. If not, you may need to try a different outlet for the cameras.

I’m having issues connecting my DVR to my phone.

Possible Fixes:

1.Please go to Menu-Configuration-Network and under the General tab make sure enable DHCP is selected, if it is not enabled then select enable and apply. If you had to enable it, restart the NVR and try the P2P setup again.

2.If you are still having issues, make sure DDNS is NOT enabled(unchecked). If DDNS is checked, uncheck it and apply then go back to Platform Access and disable P2P and apply. Once both are disabled, do a power cycle and reboot the unit. After the unit restarts enable P2P again, and do another power cycle.

3.Go to Extranet Access, Platform Access or DDNS and make sure LaView P2P is selected then apply, also make sure “Enable Stream Encryption” is disabled.

4. If none of these work, then it could be a network issue. Try to restart your modem/router by unplugging it for about 45 seconds. Plug it back in and restart the NVR, then try to reconnect your system to the P2P account.

How do I find my system’s IP address?

To find your system’s IP address go to Main Menu>Maintenance>System Info>Network. The IPv4 Address at the top is your local IP. If your IP address is 0.0.0.0 or 192.0.0.64, this means your system is offline. There are a few causes from this, but usually it’s a bad ethernet cable or the cable is not plugged in properly to either the DVR or Router. If those are checked to be correct, try restarting your router by unplugging it for a minute and restarting the DVR.

Which mobile app do I need?

-If you have DVR starting from LV-N52xxxx please download “LaView Patrol”

-If you have DVR starting from LV-N9xxxx, LV-D11xxxx, LV-D21xxx, or LV-T94xxxx, please download “LaView Net”

-If you have DVR starting from LV-D04xxxx, or LV-D51xxxx  please download “LaView Mobile”

My system keeps rebooting every few minutes. – LV-T93 units Only

You’ll need to upgrade the systems firmware to fix this issue. Try to upgrade the firmware immediately after the system has restarted to avoid a potential reboot during the upgrade process. Please follow the instructions below to do this.

Please download the firmware here: https://www.dropbox.com/s/yf6thpfyx04ag33/digicap.dav?dl=0

Once you have that file, put it on a flash drive and connect the flash drive to the DVR. Go to Main Menu>Maintenance>Upgrade and click on the Digicap file, then upgrade at the bottom. Once this is complete the system will reboot, and you’ll have the new firmware.

How do I find my system’s IP address?

To find your system’s IP address go to Main Menu>Maintenance>System Info>Network. The IPv4 Address at the top is your local IP. If your IP address is 0.0.0.0 or 192.0.0.64, this means your system is offline. There are a few causes from this, but usually it’s a bad ethernet cable or the cable is not plugged in properly to either the DVR or Router. If those are checked to be correct, try restarting your router by unplugging it for a minute and restarting the DVR.

I need to reset my password – LV-D04xxxxx

Please email us at info@laviewusa.com to reset the password for this system. In the email please mention you need a password reset along with the model number and date that displays on the main view of the system. A technician will reply with some instructions and a temporary password for your system.

How do I back up files off my DVR? – LV-D04xxxxx

To backup files on your DVR connect the USB drive to the USB port then go to Main Menu-Storage-Backup-Select USB device-Backup-Select “AVI”-Choose Start & End Time-Add-Select File-Start. Once the file has been backed up to the device please disconnect the USB drive.

How Do I set up recording on my DVR? – LV-D04xxxxx

Instructions:

2. Go to Main Menu>Configuration>Record>Record Plan>SET>Select period 1 for Normal(Continuous) or MD (Motion Detection) and then check the Select All box to copy the settings to the rest of the week. Click Apply then OK. If you’d like to set up a different schedule for each day, set the record plan for specific days individually.

3. Click the “Copy” button in the Record Plan section to copy the settings to all the other camera channels, press Apply and then Ok. All channels will have the same color scheme if this is done correctly.

How do I connect my DVR to my cell phone? – LV-D04xxxxx

Please use our point to point service. To get the P2P service working on the DVR go to Main Menu- Configuration- Network- make sure DHCP is checked (if not please check then click app. to apply). Then go to P2P under network and make sure that state says online (For model LV-KDT0808B7W go to Advanced-P2P service).

If it says the DVR is offline please check the Ethernet cable. Once P2P is confirmed online we will move to the LaView Mobile app that you can download from the Play Store or App Store. In LaView Mobile we will add a device with the “+ Device” then enter the Device ID and password shown in the P2P area. Make sure to save on the top right. Once you have your new device click on it then select 4 cameras and click the Play button. Live View should now start.

Please download the LaView Mobile app. Use the links below.

Android:
https://play.google.com/store/apps/details?id=com.vss.laview&hl=en

 Apple IOS:
https://itunes.apple.com/us/app/laview-mobile/id955357794?mt=8

For the Ipad use the HD version, this is for tablet use.
https://itunes.apple.com/us/app/laview-mobile-hd/id972423374?mt=8

LaView Mobile P2P Set Up
Note: The setup was done with an Android phone. The iPhone setup process is almost identical.

2. Click on the “+ Device” option.

3. Go to DVR, Main Menu>Configuration>Network>P2P then scan QR code or manually enter Device ID and password.

4. Press the “Save” button to be taken to the device list.

5. Select Device and select cameras. Press “Play” for Android or “Live” for iPhone to start live view.

.

How to reset the password to your Gamut recorder

This article will show you how to find the necessary information you need to send us so that we can help to reset the password for your Gamut recorder.

.

First, turn the recorder on and move your mouse to the bottom of the camera live view screen. A blue bar will appear at the bottom; click on the ‘i’ symbol that I have marked in red in the screenshot below.

.

.

This will open up a page of information about the recorder including the MAC address.

.

.

You will need to send the MAC address and the date and time on the recorder, even if the time/date on the recorder is not actually correct. 

.

This is very important, because we will generate a temporary password for you which is created based on the unique MAC address of the device and the time and date on it. If the date and time are accurate, just say that, or if you know it is five hours behind but the date is correct for example, just mention that when you email in and that should be sufficient. 

.

Otherwise, just send in a picture clearly showing the MAC address and date/time on the device and say exactly when the picture was taken.

.

Get in contact here, set the support status as ‘Password reset’ and the email subject as ‘Gamut password reset’. You will also need to send your original order/invoice number and the original delivery postcode to confirm your identity.

We will try to get back to you as soon as possible.

How to set up and view your Gamut PTZ on a Windows or Apple computer (GTIP210PTZ)

Purpose of The Guide

This guide will walk you through the initial configuration of your Gamut PTZ and show you how to view the camera on your computer.

.

Before You Begin

Let’s Get Started

First we need to make sure that the camera is talking to your network. If you look on the box for the camera and on the side of the camera itself you should see a sticker that looks something like the one shown below.

.

.

Make a note of the IP Address, User name and any Password shown on the sticker.

.

Next we need to open Internet Explorer on the computer. In the address bar at the top of the page enter the IP address that you saw on the sticker. You should then be prompted to log in to the camera, here you need to use the User name and Password shown on the sticker, if there is no password on the sticker then leave the password field blank.

.

Please make sure that you are using Internet Explorer and not any other browser. The reason for this is that most CCTV systems require the use of software called Active X to be able to display your live video and that software is only supported by Internet Explorer.

.

If you are prompted to install any software you need to allow this to happen, this software enables your computer to display the video feed from the camera.

.

At this point you should be seeing a live view from your camera and can go ahead and fit your camera wherever you need it. To watch your cameras in future you will simply need to open Internet Explorer, go to the IP Address from before and log in to the camera. From there you can also control the motion of the camera by using the PTZ controls shown below. These features are explained more in depth in other guides which can be found here.

.

If you were unable to access your camera this way then it’s not a problem, we just need to use a different method. Alternatively if you wish to view the system without having to log in through Internet Explorer each time then continue reading and you will see how to view the camera without needing to log in each time.

.

First open CMS5/VMS, the program that you installed before we began, and click on Device Manager. You will now be presented with a screen that looks like this:

.

.

You should see a camera in the list that has the same IP Address as previously seen on the sticker on the camera. If you don’t then click the IPV4 Search button and after a few moments the camera will appear. Select the camera by ticking the box to the left of it and click Add.

.

The camera will now be displayed in the bottom half of the window. Towards the right hand side you will see a number of buttons, you need to press the Modify IP button as highlighted in the following image.

.

.

At this point if you wish to use the camera through Internet Explorer rather than CMS5 you are now able to. Make a note of the new IP address that the camera is displaying and follow the steps detailed near the top of this guide for accessing the camera using Internet Explorer.

.

Now click the Home button to return to the main page for CMS5/VMS, then click Monitor. On the right hand side you will see your camera in the list of devices. Double click on your camera and the video feed will appear in the middle of the screen. If you then double click on the video if will go in to full screen mode so you can see a larger picture. To then control your camera click the button shown below and the PTZ controls will appear. As before more articles about controlling your camera can be found by clicking here.

.

GAMUT RECORDER Installation and user guide

Read More : UNV Recorder Set Up Guide

How to add your Gamut recorder or camera to a mobile phone or tablet

Purpose of The Guide

This guide will show you how to add your Gamut camera or recorder to a phone.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. If you have a recorder with a hard drive you will need to use a TV or Internet Explorer to set it up for the first time, follow the quick start guide to do so.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

You will need to download the app RXCamView onto your phone or tablet.

Android

.

Apple

.

Let’s Get Started

Open up RXCamView on your device and tap on the head and shoulders icon to open the side menu.

.

Then tap on ‘Device List’.

.

.

On the Device Manager page, tap on the ‘+’ icon then tap on ‘IPC/NVR/DVR’.

.

.

The app will request permission to use your camera, allow it to. It will open up your camera and you need to point the camera to the QR code on the label on your recorder or camera.

.

.

Once you have successfully scanned the QR code the app will prompt you to fill in some information. Leave the IP/Address and Media Port fields, the username is admin by default, and the password is blank by default.

.

Then the device will appear in the device list, it should say ‘Connected’. If it says ‘connect close’ then check the password is correct and that nothing has been disconnected.

.

.

If you tap on the play icon underneath the device, you will be taken to the live view window. Just tap on the name of the device to begin live view.

.

.

To view recordings, just tap on the film reel icon at the bottom right below the live view screen:

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

.

If you find that the device only works when you are connected to the same internet router as it, and not when accessing it via another Wi-Fi network or with 4G, take a look at this guide.

How to access your Gamut camera or recorder using a Windows or Mac computer

Purpose of The Guide

This guide will show you how to access the live footage, recordings and settings of your Gamut camera or recorder, using a Windows or Mac computer.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. You will need to use a TV to set up the recorder for the first time, follow the quick start guide to do so. After the initial setup, a TV or monitor is not necessary when accessing the recorder via a network connection.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

Let’s Get Started

Now that you have connected your recorder/camera to your internet router and turned it on, you will be able to view it using a program called Surveillance Client.

.

First you will need to download some software called Device Config Tool, which will allow you to find out the IP address of the camera/recorder and edit some of the settings.

.

Download it from here if you are using Windows, and here if you are using a Mac.

.

Once the software has been downloaded and installed, you will see a window like the screenshot below. Make a note of the camera/recorders IP address.

.

.

If the recorder/camera does not appear in the program, first ensure they are turned on and check the connections from the device to your internet router. If you are using a Wi-Fi bridge system, make sure that they are configured correctly (if they were not pre-configured) and are both turned on.

Surveillance Client

If you are using Windows you can download Surveillance Client from here.

.

If you are using a Mac, download it from here.

.

When you have downloaded and installed Surveillance Client you will be presented with a set-up wizard. Click Next, then Add Online Device. Your recorder/camera should appear in the list; select it then click Add Selected Device. 

.

.

Now choose a name for the recorder/camera. By default the username is admin and the password is blank. Now click ‘Add’.

.

.

You will see the device appear in the left hand pane. Select it, click ‘Import’, then open the ‘DefaultGroup’ folder on the right side and you will see it has been added.

.

.

Click ‘Next’ then ‘Finish’ and you will be taken to the main menu. Now click on ‘Main View’.

.

.

When you are taken to Main View, double click on DefaultGroup, then the name of your recorder (if you have one) and the cameras will be shown. In the screenshot I only have one camera connected, which is signified by the green play icon. Double click on the camera name to begin live view. If you want the camera to be in full screen, double click on the live feed.

.

.

To access recordings, go to back to the Control Panel and then click on Remote Playback. Open up DefaultGroup on the left side panel, then select the cameras which you would like to view recordings from and click the play button. You can select the date using the calendar on the bottom right.

.

.

To access the settings of the recorder/camera itself, go to the Control Panel, click on Group Device, then click on the spanner icon next to your recorder.

.

.

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

MORE PAGES >>>

Support log in with cloud technology

Support real time live view

Support remote playback

Local recording and play

Support snapshot and pictures searching

Support bidirectional talk

Support PTZ control

Support scanning serial number by QR code

Support cloud user register and modify

Support remote device add, edit and delete

Support local device add, edit and delete

Support adding device by address

Support manually searching device in LAN

Support version updating automatically

Support searching device function by shake

.

How to find out the “Cloud ID” (Serial Number) when adding device to PC Client “VMS”?

The “Cloud ID” is “serial Number”on the NVR UI Monitor Interface

Go to your TV Monitor that is connected to NVR, Navigate to “Main Menu–>Advanced–>Version“–> You will see the Serial Number

How to Flip the Camera

1. select the channel of the flip camera

2. Navigate to “Main Meun“–> “XVI control“

3. check the”Overturn

How to reset XMEye Pro Password?

1. Click on “Forget Password”

2. Input your number or Select “Email”(Depends on the method you signed up before)

3. Input your email address and click on “Get Code”

4. A code will be sent to your email, input the verification code here and click on “Next” to continue.

,

XMEye New Gui User Guide

Read More : XMEYE – How to connect DVR/NVR on PC Mobile Browser

How to Share the APP to other

1.Open the “Xmeye Pro ” app ,Click the pencil to edit,

Then Click the Share

.

2.Select the function which you want to share

.

3.Finally enter the user name who you want to share ,then you can shre to others successful.

My UI Interface shows “No signal” or “Black Screen”

We need to divert this issue into two situations:

1. DVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur. Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

  (2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having the issue, and needs a replacement, plz contact email love@hiseeu.com for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

.

2.DVR Indicator light is off:

(1) Cause: The power adapter 12V 2A connected to DVR box is broken

Step: Use another power supply 12v 2A to power on the DVR unit to have a try

( If you do not have a spare one, use the one that is connected to 4 cameras to have a try)

(2) Cause: The hard disk drive inside of the DVR box is broken Step: Use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email love@hiseeu.com for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

My UI Interface stuck in Hiseeu Logo

We need to upgrade the system to solve this problem, and check customer’s NVR mainboard info first, and take a photo for us to make sure about firmware verison, then we will ask manufacturer to send us a firmware to upgrade the system to solve this problem

1. If you are in the phone call , just let the customer take a photo of the mainboard, and send it to email love@hiseeu.com. We will ask for a firmware to solve this problem during our working time

(Different versions have various firmware, there is no standard firmware to upgrade the system, so we need to ask the original manufacturer to do that)

2. If you are dealing with the email:

Try with the steps:

1. Ask the customer to open the DVR box by using the screwdriver, and take a photo of this mainboard, and make sure the QR Code is clear enough for us to scan

2.After receiving the photo of the mainboard,  we will ask the XM Manufacturer for a firmware, and upgrade the NVR with the new firmware.    

Upgrade steps

Attached upgrade firmware is for your reference, please download and unzip it first.

1. Copy these 2 files to your USB flash drive, the root directory(Do not under any folder, see the picture attached)

2. Power off the DVR and insert the USB device

3. Power on the DVR, it will upgrade automatically. Please give it a try and let us know the outcome.

How to Sign Up APP Account

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

[Note: You can tap on “Local” for quick login without registration. (In this situation, you still can have live view and playback but are not able to receive motion detect alarm message), so mostly we suggest customers to sign up an account first]

Network “Probing DNS”?

1. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online

–>2. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply; –>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

One or two cameras are not wokring

(1) BNC Cable connected to Camera is broken

Step: Use another BNC cable to connect the camera to have a try

(2) The port of the DVR box is broken

Step: After changing the BNC cable, and still there is no camera image, plz insert the camera into another port of the DVR to have a try

(3) Camera is broken after troubleshooting with the steps （1）–（2）

Unable to open VMS archive file

Please drag the exe file to your Desktop interface (do not under any folder) and run it again.

Like it the photo shows , plz do have a try again ,the VMS will run normally

Upgrade NVR/DVR firmware

If customers need a firmware upgrade for NVR/DVR, and we need the “System version” to send to XMmanufacturer to ask for a firmaware to upgrade  

Go to Monitor UI Interface, and navigate to “Main Menu– Advanced–Version“

After get the Version:

Please follow the instructions below to upgrade the NVR/DVR firmware. Steps:

Attached new firmware for you, please download it and unzip it.  

1. Copy to your USB flash drive, and put it in the root directory(Do not under any folder)

2. Plug the USB device into NVR/DVR

3. Navigate to “Main Menu–> Advanced–> Upgrade”

> Upgrade position(Select your usb device)

–> Upgrade file (Select the firmware)

–> Upgrade

What if the APP keeps asking the user and password?

Step: Plz input the Monitor UI user name and password to resolve this issue

The cause： Sometimes the APP would be in the process of auto-maintain, so it would ask for the user name and password to protect the account’s safety. This page will pop up when you want to live to view the camera.

Note: Some customers enter the App account user name and password. Actually, it’s the Monitor UI user name and password      

As for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu“, this interface [system login] will pop up, and here are the user name and password we need to enter into the app

.

Add device on PC Client(VMS)

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=  

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=  

.

1. Download PC Client “VMS” and installed

[ Need to drag the file to the desktop after installing firmware, or it would ocurred the issue of “unable to open archive file”]

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID

Device Name: Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

[Note: most customers do not know how to find the serial number, so they can’t add the device to PC Client

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

[Note: Most customers do not know their user name and password, so we need to guide them to go next to the TV monitor, and right click the mouse from “Log out–Log out”, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

Enable the APP push notification on mobile app “XMEye Pro”

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

1.Please right-click mouse and navigate to Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK” (Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to Event–>Device (the one you named)–>Enable “Allow Notifications”

.

Add device to mobile APP (XMeye Pro)

.

As for how to add the device to mobile APP(XMeye Pro), please follow the below instructions

–>1. Please connect the NVR box to your Router via Network Cable;

–>2. Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR is online (Please skip step3), 

.

–>3. If the cloud status shows “Probing DNS”, Please Navigate to Main Menu > Network > Check Enable DHCP–>Apply;

–>Reboot DVR by unplug power adapter and re plug it, then double-check the cloud status. 

.

–>4. Go to your TV Monitor, navigate to Main Menu–>Advanced–>Version–> You will see the serial number. 

The QR code contains serial number info. 

.

–>5. Open the mobile APP “XMeye Pro” and register an account by your email

–>6. Click”+” to add device–>Choose “NVR”

Click the “Scan” icon to Scan NVR’s QR Code. (QR code contains username and password)

No need to input the user name and password manually.

And click “Ok”, and go back to the Device page on App,and you will see the device shows status: online ,

.

Note1:

We do not suggest customers to manually input the serial number, If they input it, the user name and password need to be input, If they scan the code, they don’t have to input the user name and password, So we need to guide them to scan the QR code first, in some situations if we really need the information of the user name and password, and for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

Note 2:

If device shows “offline”, there could be two causes:

(1) DVR is not connected to network successfully, plz go back to Monitor UI Interface to check if the cloud status shows connected or not in the path of “Main Menu > Network > Net Service”

(2) The way he adds the device to the app is wrong, especially some customers don’t know how to find out the QR Code and input the wrong user name and password

What should I do If I forgot my DVR password

1.Right click mouse from home screen, Click “Log Out–>Log Out”

2.Then click “Forget password” ＞ “Forget answer ” ＞ Then you will see two “QR code” on the monitor

3.Open your Mobile APP “XMEye Pro” , 

(1). Click the “+” icon on the top right corner—>Hit “NVR”

(2). Click “Forgot your device password”–> Scan the QR code (CAPTCHA on the TV monitor)

(3). Scan the QR code shown on your TV monitor. You will get the verification code.

(4). Input the code in “CAPTCHA”

Why can’t live view the videos on mobile APP or PC Client VMS

1.Please make sure that your DVR system is already connected to the router through ethernet cable successfully

2.Please go to Main Menu > System > Net Service to check the network is connected or not, Cloud should shows: connected 

3.Make sure the way you add device to your mobile app or PC client with correct serial number and password

Serial number: “Main Menu–Advanced–Version”

Password: DVR login password 

Why the DVR can’t record or playback video

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

1. Check if the hard drive status is normal or error

Navigate to: Main Menu–>Advanced–>HDD info. 

 If it’s hows “error” or no hard drive info, means hard drive failure. (need to replace hard dirve)

2. Check the record plan is set up for 24/7 continues recording

Navigate to Main Menu–>Record Conf

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3.   Please make sure the HDD was set up to “Overwrite”

Navigate to Main Menu–>General–>Storage Full

Any ideas, let us know. Thank you for your cooperation. 

.

Welcome to our updated comprehensive how-to guide for getting started with your Hikvision IP CCTV system. IP systems are taking over the surveillance world and whether you’re setting up your brand new Hikvision system, or you need help adding more cameras to an existing setup you have, the step-by-step guides in this Megaforum should be all you need to get up and running!

Part 1: How do I install a Hard Drive in a Hikvision NVR?

Any setup with an NVR will need a hard drive to function as it is what all your footage is saved to. The WD Purple Drive is our go-to recommendation for the vast majority of IP setups as it designed with the high workload requirements of 24/7 surveillance solutions in mind. Please see the guide on picking the right HDD to better understand your storage needs and why we don’t recommend using HDD’s that aren’t optimised for use in a CCTV system.

Please see the five simple steps below for getting your hard drive installed into your NVR:
.

.

Step 1:
.

Firstly, you’ll need to locate and remove the screws that secure the NVR’s casing to the base so that you can access the inside of it. Typically, you’ll find two of these screws on the back of the unit and, depending on the NVR model, more on the sides – Do not lose these screws!​

.

.

Step 2:
.

Once inside, your NVR will look something like this. The parts in here you’ll need to identify are the:​

.

.

Now look at your HDD – fewer things to identify here:​

Step 3:
.

Get your hard drive and NVR connected – You can screw the drive into its bay in NVR first if you wish, but it’s normally easier to wire everything up first. Plug one end of the SATA interface cable into the HDD and the other into the corresponding port on the motherboard, then do the same with the SATA power cable. If the power cable has come already connected to the motherboard, then just plug the other end into the HDD’s SATA power port.​

.

.

Step 4:
.

You now just need to screw the HDD into the bottom of the NVR via the screw holes located in the HDD and corresponding holes in the HDD bay (insert the screws from underneath the NVR into the HDD inside – it can be a bit fiddly).​

.

Step 5:
.

Finally, screw the NVR’s casing back onto the base. Your HDD is now installed and ready to be formatted during the initial NVR setup, which is explained in Part 2.​

Part 2: How do I complete the basic setup of my Hikvision NVR?

You now need to configure the NVR so that it’s ready to connect to your network. Don’t worry – this is simpler than it sounds. This initial setup is simplest when done on the local GUI, using a directly connected monitor. The following steps walk you through this initial setup process:

Note – Avoid plugging anything into the back of the NVR until instructed to do so in this tutorial.

Firstly, you’ll need to look at the back of your NVR and make sure you can identify the following parts that are needed for this stage:
.

[1] – PoE (Power over Ethernet) ports (Most Hikvision NVRs have PoE ports which will power any camera via the network cable. Those that do not will require you to connect the camera across remotely, using a separate PoE injector or switch for power.)
​

[2] – VGA display port
​

[3] – HDMI display port
​

[4] – USB port(s) (and mouse – one should come included with the NVR)
​

[5] – LAN port (and ethernet cable – Cat5e or Cat6 is fine)
​

[6] – Kettle power socket (the power lead is included with the NVR)​

Now, follow these steps. It is easier if you leave your cameras disconnected until prompted later in this guide:

Step 1:
.

Plug the kettle plug into the power inlet to connect the NVR to a power supply.​

​

​

.

​

Step 2:
.

Connect your NVR to a display (this can be any monitor or television) by connecting either an HDMI or VGA cable from the monitor to the corresponding port in the back of the NVR.​

​

.

​

Step 3:
.

Plug your USB mouse into one of the NVR’s USB ports.​

​

​

Step 4:
.

Use an ethernet cable to connect your NVR to your local network – Plug one end of the cable into the RJ45 ports into a network access point (such as an ethernet port on your router), and the other into the LAN port in the back of your NVR.​

​

​

.

​

Step 5:
.

Turn the NVR on and let it boot up. Ignore the beeping noise, it’s completely normal and just the NVR telling you that it isn’t properly configured yet.​

​

You may get a prompt to adjust the NVR’s resolution to match the connected display, click “yes” to view everything in the best resolution supported by your display.​

​

​

​

Step 6:

​

Set your language when prompted.​

​

​

​

Step 7:
.

Set a password for the NVR , as well as a “Channel Default Password”, which will be passed onto any inactive device that is directly connected to the NVR’s PoE ports. We recommend keeping these passwords the same for simplicity’s sake. It’s key that you set a password that the NVR defines as strong and that you remember this password, as resetting the passwords on Hikvision devices can be a hassle that you want to avoid, if possible.​

​

Note – If you have lost your password then please see our guide on How to Reset the Password of your Hikvision Camera/NVR in 5 steps using the SADP Tool​

​

​

​

Step 8:
.

Now set a valid “reserved email” address for the NVR, which Hikvision will use for verification if you need to reset your password.​

​

Step 9:
.

Next, set an unlock pattern of your choice by using your mouse to draw any shape you like – you will be asked to do this twice to confirm the pattern. This will be used to quickly login to your NVR in the local GUI.​

​

​

Step 10:
.

Now, set your time zone, your preferred date format, and date/time.​

​

​

Step 11:

​

On the Network Setup page:​

​

Leave the “NIC Type” as it is.​

​

Either leave the “Enable Obtain DNS Server” box ticked, or untick it and use one these recommended public DNS servers.​

​

It is best to leave the “Enable DHCP” box unticked here. Instead, set the “IPv4 Address” of the NVR to an unused IP address on your network, which is within your gateway’s range. Your Gateway will typically be the IP address of your router. E.g. if your router’s IP address is “192.168.1.1”, you’ll want to give the NVR an IP address within the range of “192.168.1.x”, where “x” is any unused address between “2” and “254”.​

​

Note – DHCP can be left on during this stage of the setup to automatically assign your NVR an open IP address if you like, just be sure to turn it off again once your system up and running. To disable it again once set up, just go to: ​

System/Configuration→ Network → TCP/IP → DHCP Off → Apply​

​

Input the Subnet Mask of your network (typically it’s “255.255.255.0”) and “IPv4 Default Gateway”. If you’re unsure of these, see the below articles which explain how to check what they are and if a particular IP address is available:​

How to setup Hikvision IP CCTV System

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

The “Internal NIC IPv4 Address” can be left as it is, this just refers to the NVR’s own LAN address (so Plug and Play cameras will use IP addresses on this range).​

​

​

​

Step 12:
.

You can now stop the annoying bleeping! Select your hard drive(s) from the list and click “Init” to format it, and then “Next” when the formatting has completed.​

​

Note – This will completely wipe the drive, so please make sure that any that are being reused to not have data that you might need on them. ​

​

Step 13:

​

The next page is for the Camera Setup. As mentioned earlier, we recommend connecting any cameras after the NVR setup process has completed, so you can skip this page.​

​

Note – Please see part 4 for the instructions for adding cameras to your NVR after the initial setup. ​

​

Step 14:
.

You will now be taken to the platform access page. Again, skip through and leave this for now.​

.

Note – Please see part 12 for adding the NVR to the Hik-Connect app, which revisits this page. ​

​

​

Step 15:
.

Finally, you’ll be taken to the Change Password page and given the option to set a new admin password. Ignore this, unless you actually want to change your password. Remember, your admin password is different from your activation password, which you’ll need to use when activating individual cameras on your network.​

​

Click “Exit” and “Yes” on the “Exit Wizard” popup.​

​

​

.

That’s the initial setup of your NVR complete. You should now be taken to the NVR’s live view page (you won’t see your cameras until these are connected in Part 4), with your main navigation menu at the top of the screen.​

​

.

Part 3: How do I find my Hikvision device and edit its network settings?

You probably want to be able to view your camera feeds remotely wherever you are; either in a web browser, the iVMS-4200 software, or the Hik-Connect mobile app. All IP CCTV devices communicate over your LAN (local network) and have a unique location on the network. So, you will need to be able to locate where the device you want to view is and make sure it has the right settings for it to work on your LAN. You will then be able to access the device from a PC or mobile device, and connect it with the rest of your CCTV system.

Please follow the steps beneath to find and correctly set your Hikvision device’s network settings.
.

.

Step 1:
.

The first step is to work out if you need Hikvision’s SADP tool or not. If you only need to discover and access an NVR and some Plug and Play cameras connected directly to its PoE ports, then you don’t need to use it.​

​

​

If you aren’t using the SADP tool:​

​

Or, on the NVR’s local GUI (Graphical User Interface – when operating the recorder from a connected monitor and mouse), go to:​

​

System → Network → TCP/IP​

​

Here, you can view and change the NVR’s network settings to match your LAN which is explained in step 2 – you can then ignore the rest of the steps.​

​

​

If you are using SADP:​

​

If your cameras are connected to your LAN, rather than to an NVR’s PoE ports, you will need to install the SADP tool. This scans for all Hikvision devices on your LAN by their MAC addresses. Now, follow steps 2-5 below.​

Step 2:

​

You now need to identify some of your LAN’s settings, which you need to set to match on your devices.​

​

From a Window’s PC, you will need to use the Command Prompt tool to find these.​

​

If you’re using a Mac, then you can find these by launching System Preferences, and then going to:​

​

Network → Advanced (make sure your Wi-Fi/Ethernet connection is selected on the LHS) → TCP/IP​

​

​

Make a note of the following numbers, as you will need to use them when changing your device’s network settings:​

​

IPv4 Address – This is the IP address of the computer that you are using. This address is therefore already occupied, so you will not be able to assign any other devices to this specific address. The digits after the final decimal point indicate where the device is located within the range of your local network, which spans 1-254. You’ll need to change the number after the third period (or full stop/dot) to something that is between “1” and “254” and not already occupied by another device on the LAN.​

​

NB – Please see these guides for instructions on checking if a proposed IP address is occupied:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

Subnet Mask – This shouldn’t need to be changed on the NVR, it will usually be “255.255.255.0”.​

​

Default Gateway – This is the IP address that’s been assigned to your router. Any device being added to your system needs to be within the range of your gateway in order to be discoverable.​

.

Step 3:

​

Now, launch the SADP tool again. It should show a list of all the Hikvision devices on your local network and their default network settings. Provided the device is being powered and has a connection to your LAN, then it will show up here. You can also alter the device’s network settings here, and check things like the model number, serial number, the firmware version installed on it.​

​

NB – Remember that any camera that is directly connected to your NVR’s PoE ports will not show up in SADP. This is because the NVR hides any cameras directly connected to it from SADP on its own “subnet”, which is separate from your local network. Don’t worry though, as you won’t need to change the settings for these cameras. ​

.

Step 4:

​

Tick the box beside your device to view and edit the network settings.​

​

If the device hasn’t yet been connected to the network then it will show as “Inactive”. You will be asked to set a password for it when you click the tick-box for it. For more instructions on activating your device, please see Part 6.​

​

​

.

.

​

Once activated, ticking the box beside your device will change the network settings in the “Modify Network Parameters” window, so that they match your LAN. You need to make sure that you enter the password for that device before clicking “Modify” for these changes to be saved.​

​

.

Step 5:
.

Check that these changes have been reflected in the SADP device table – you may need to wait a few minutes before refreshing. If they have, then you should be to carry on with getting this device connected to the rest of your system.​

​

NB – If you aren’t the camera’s first owner then you will need to perform a hard reset on it. This will reset the device to its inactive factory state so that you can set new password by activating the camera in SADP. Once this has been done, SADP will allow you to modify each network setting edit the network settings to match your LAN so that you can use the device standalone or add it to your NVR remotely.

.

Part 4: How do I add a Hikvision device to my NVR?

There are a couple of methods for getting your IP camera connected and recording to your NVR:
.

Plug and Play – This is the most popular and simplest method for smaller setups, as all you need to do is plug your camera straight into the PoE ports in a Hikvision NVR. The NVR will then do the rest of the work. Please note that for Plug and Play to work, the device will need to be inactive or activated with the same password as the NVR.​

​

Remote connection via IP – If you can’t have a wired connection to the NVR, you can instead remotely add a camera on the same network as your NVR to it using the camera’s IP address. For this to work, you will need to make sure to do two things:​

​

1. Replace the power supply that would normally come from the NVR’S PoE ports. Using a PoE switch or injector is usually the best way, as it means you can still add power to the device over the same ethernet cable used for everything else. If not, most will let you connect to a separate PSU.​

​

2. You have connected the camera and NVR to the same LAN and that its network settings are correct for the LAN’s range.​

The following steps will guide you through adding new devices using both of these methods. Part 1 covers doing this on the NVR’s local interface (GUI) and part 2 covers how to do this remotely using a web browser.
.

.

Method 1 – Via the NVR’s GUI:

.

Step 1:​

On the NVR 4.0 menu at the top of the screen, go to:​

​

Camera → Hover over the desired channel → Click on ‘Edit’ (small icon in the bottom-left corner of channel thumbnail)​

​

​

.

Step 2:​

An edit window should appear, fill out the fields to add your camera as follows:​

.

Option 1 – Using “Plug and Play”​

​

Connect the camera to the corresponding PoE port number on the NVR (I.e. D1 corresponds to port 1). Then, just select “Plug-and-Play” from the “Adding Method” dropdown, and then click OK to add the camera to that channel – the camera feed should appear after a few seconds to confirm that it’s been picked up.​

​

Note – If you haven’t activated and set a password on the device in SADP, then the IP address should automatically work. The password will be the Activation Password set on your NVR in the initial setup.​

.

.

Option 2 – Adding manually via IP​

​

Change the “Adding Method” to “Manual”, which will let you alter the other fields.​

​

Now edit the other fields to point your NVR to the camera’s location on the network, like below:​

​

​

Adding Method – Select “Manual”.​

​

IP Camera Address – Enter your camera’s IP address here (as explained in the introduction, this will need to match the range of your LAN).​

​

Protocol – Select the device’s manufacturer if it is on the list, or “ONVIF” if it is an ONVIF conformant product.​

​

Management Port – “8000” by default will work fine, or whatever you’ve set the device’s Server Port to if it’s been changed.​

​

Channel Port – This refers to the channel that you want to add the camera to, so leave this as the corresponding number for the channel that you would like to edit.​

​

Transfer Protocol – Set this to “Auto”.​

​

Username – The username you set up when activating the device, usually “admin”.​

​

Password – The camera’s password, which you will have set when it was first activated.​

​

Use Channel Default Password – If you have assigned the NVR and camera the same password during their activation, then you tick this box. This will use the NVR’s password to add the camera and will save you from entering it again in the future.​

​

Enable IP Camera Time Sync – Tick this, as it means the camera will synchronise with the time set on the NVR.​

​

Use Default Port – You can leave this unticked, as you have specified the management port already.​

​

Verify Certificate – Leave this box unticked too.​

​

​

Click OK to save your changes, the NVR should pick the camera up after a few seconds and show the feed on that channel’s thumbnail to confirm this.​

.

.

Step 3:​

To rename the camera, go to:​

​

Camera → Display​

.

Then, select the camera’s channel from the dropdown, and use the field below to set a new name.​

​

Click “Apply” to save your changes.​

​

​

​

​

Step 4:​

You may want to rearrange the Live View screen to show the new camera on a particular tile. To do this, first, go to:​

​

System → Live View → View​

​

Then, select the output port for your connected display that you would like to show the camera on, click on the selected tile and then double-click on the new camera to add it to that tile.​

​

You can select different layout options, or create a customised layout using the toolbar at the bottom of the page.​

​

Click “Apply” to save the new layout.​

​

​

To check the new layout, launch “Live View” using the NVR’s main menu, and then select that layout using the toolbar in the bottom right-hand corner.​

​

​

.

Method 2 – In a web browser:

.

Step 1: ​

Browse for NVR’s IP address in a web browser, and log in with your username and password for it.​

​

.

Step 2:​

Now, navigate to:​

​

Configuration → System → Camera Management → IP Camera​

​

You’ll be shown a table of all the NVR’s channels, showing which are occupied by cameras, and which aren’t.​

​

These channels normally correspond to the same-numbered PoE ports on the back of the NVR.​

​

Click on the channel that you want to add your device to, and then the “modify” button above the table.​

​

.

Step 3:​

A window titled “IP Camera” should appear allowing you to change the “Adding Method” and “IP Camera Address” set for that channel.

If you haven’t already, you will need to make sure that the camera has a valid IP address and correct network settings for your LAN’s range.
.

Option 1 – using “Plug and Play”:
.

You just need to make sure that:​

​

Note – If you haven’t activated and set a password on the device in SADP prior to connecting it to the NVR, then the IP address should automatically work and the password will be the “Channel Default Password” set on your NVR in the initial setup (see step 7 here)​

.

Option 2 – Adding manually via IP:​

​

Change the Adding Method to Manual, which should let you alter the other fields.​

​

Now alter the other fields to point your NVR to the camera’s location on the LAN, like below:​

​

​

IP Camera Address – Insert the camera’s IP address​

​

Protocol – Select the brand of your camera here, or ONVIF if it is ONVIF conformant and the manufacturer doesn’t appear in this list.​

​

Management Port – This is the camera’s network port, which is usually 8000 by default.​

​

Username – The username that you set for the camera, which is usually “admin”.​

​

Password – The password assigned to the camera upon activation in SADP. If you have automatically activated the camera by plugging it into your NVR’s PoE ports, this will the the “Channel Default Password” set during the NVR setup.​

.

Confirm: Retype this password.​

​

Transfer Protocol: This is fine for you to leave as “Auto”.​

​

.

Green ticks should appear beside each field to indicate that what’s inside is valid. Once completed, you can click “OK”:​

.

​

The “Security” column should be “Strong” and “Status” should change to “Online” on the “IP Camera” page – If they do, then you’re finished, just return to the Live View page to check that the camera’s feed is now visible.

​

Note – Clicking the “Start All Live View” button in the toolbar at the bottom of this page will show all of your working cameras feeds at the same time.​

​

Click on other pages for more.

with a wealth of intelligent products, we strive to identify and satisfy diverse demands by delivering intelligence at your fingertips; through innovative AIoT applications, we are dedicated to empowering every individual to enjoy a better future by building an intelligent world that is more convenient, efficient and secure.

Hikvision ‘How To’ Tutorials

Here you can find all of the Hikvision-related ‘How-To’ Tutorials that the team at use-IP have created

How Do I Configure the Camera’s Onscreen Display Text?

All Hikvision users will have seen that when you first log in to a camera the live view will have overlayed text stating the date & time and the default name of the camera “IPcamera 01”, depending on your requirements you may want to change some or all of this overlay text and below is the instruction for how to do that.

Method 1 – In a Web Browser

Log in to the camera and go to Configuration > Image > OSD Settings
.

Below we will take you through each of the above settings and what they do:

Character Set – This lets you select the characters/language the OSD settings use, by default all UK stock will come with this set as GBK for English characters but if you are a European customer and you want to enter special characters from your particular language (e.g. é, ü, ç, etc…) you can switch it to EUC-KR to access those characters (do this will require the camera to reboot).

Display Name / Date / Week – These tick boxes let you show/hide the camera name (Display Name), the current date (Display Date), and the day of the week (Display Week)

Camera Name – This box lets you set the displayed name of the camera, it will also change the name of the camera shown in the System menu and if added to an NVR it will change the name shown in the live view camera list and the Camera Management list.

Time Format – This dropdown lets you select how the time appears in your live view, either 24-hour format (00:00 – 23:00) or 12-hour format (00:00 – 12:00)

Date Format – This dropdown lets you select how the day, month, and year are displayed. Your options are DD/MM/YYYY (UK format), MM/DD/YYYY (US format), and YYYY/MM/DD (Chinese/International Standard format). You also have the option of separating the day, month, and year with either a “–” or a “/“.

Text OverLay – On most cameras, you should have the option to add up to 4 additional text overlays to the live view. You can use all of them or none of them depending on your requirements.

Display Mode – This dropdown lets you choose how the text behaves on screen, by default it will usually be set to Not Transparent & Not Flashing which means the text will obscure objects/people behind it and it will be onscreen all the time. You have the option to change it to one of the following – Transparent & Flashing / Transparent & Not Flashing / Not Transparent & Flashing – When set to transparent the text will become semi-transparent so that you can see objects/people behind the text and if set to flashing the text will flash on & off screen every few seconds (there are no controls for the flashing duration).

OSD Size – Technically this setting should adjust the size of the OSD text but we’ve found that when changing it there was little change to the text and so we would just stick to the default Auto option because this will allow the text size to adapt based on where you are viewing the live image (e.g. whether a small phone screen or a large TV).

Font Color – This dropdown lets you select the colour used by the OSD text, by default the camera will use Black&White Self-adaptive which means the text colour will automatically switch between black & white based on what is behind the text (e.g. if a person walks through the text) and for high-security sites, this can be an important feature for using the footage in court because the adaptive text shows that the image/text has not been manipulated in post. If the scenario requires it you can select Custom which will allow you to pick the text colour from a standard colour table.

Alignment – Again like OSD size this setting doesn’t appear to have a huge impact so we would just leave it as the default Custom and you can adjust the positioning/alignment of the OSD text by dragging the red boxes around the live view window above (these red boxes are only for adjusting the text position and will not appear on the actual live view image).

 .

Hikvision Full installation guide

 .

Read More : How To basic setup of Hikvision NVR

 .

.

Method 2 – Via the NVRs GUI

.

You can access similar OSD settings from the NVR by going to Camera > Display and selecting the camera you want to configure.

.

Although, as you can see from the above screenshot you won’t get all the settings that can be found by logging into the cameras directly.

How do I set up ‘Rotate Mode’ on my Hikvision IP camera for the best picture in narrow scenes?

Corridor mode is a really useful feature available on many different CCTV cameras that can be utilised to effectively monitor a space that is more vertical, rather than horizontal, in shape. These types or areas include hallways, pathways, staircases, shopping aisles, tunnels and roads. When installing and viewing a CCTV camera, you want the image frame to include as much of the area of interest, while cutting out as much of the redundant areas, like the walls and ceiling, as possible.

 .

Corridor mode allows you to rotate the camera’s lens and the video image 90 degrees so that it’s in a portrait, rather than a landscape format. As a result, you can use the camera to really focus on those areas of interest of within in your frame changing the image’s aspect ratio from 16:9 to 9:16 to suit narrow monitoring settings. The image below is taken from a camera making use of this function and illustrates the differences between the corridor and standard settings:
.

This guide will show you how to utilise corridor mode on Hikvision’s three most popular camera types: domes, turrets, and bullets. I will cover how to activate this useful setting in iVMS-4200, a browser, and locally through your NVR’s GUI so that, irrespective of your setup, this guide should be of help.

Part 1: How do I activate the corridor mode function in my camera’s settings?

We suggest getting your camera set up on your network and activating corridor mode in its settings before you try to rotate and position the lens. This way, you can use the live video stream, in the correct aspect ratio, to point the lens in your optimum direction. Positioning the lens often involved a bit of trial and error to get the best result specific to your space.

.

Note – For the G2 AcuSense models, you will need to connect to the camera directly in a web browser and change the “VCA Resource” to Monitoring Mode by navigating to:​

​

Configuration → System→ System Settings → VCA Resource​

​

​

.

​

Please note that this will disable most of the smart event options, leaving only Scene Change Detection available to use. ​

Locally (via a monitor connected to an NVR):

If your camera is connected to an NVR, then you can easily configure corridor mode in the setting through the NVR’s GUI menu. Just Navigate to:

Menu > Camera > Image

Pick your camera from the top drop-down box beside Camera and then select “Clockwise 270 degrees” in the Enable Image Rotation box

Then, just click Apply

Through iVMS-4200:

If you’re not using an NVR, or don’t have easy access to your NVR’s GUI, then an option is to use iVMS-4200 to set up corridor mode by accessing the camera directly.

To do this, first, you’ll need to navigate to:

Menu > Device Management

.

Find your camera in the device list. If accessing a camera connected to an NVR, you’ll need to open your NVR within the Group section of the Device Management screen and then the particular camera within the NVR’s device list.

Click Configure (the small cog) on your camera.

If your camera isn’t connected to an NVR, then open Basic Settings, if it is then open Advanced Function.

.

In the popup window, open the Image tab in the sidebar. You should then see either a tick-box or drop-down that allows you to turn on Rotate, tick or select ON in the applicable box or drop-down and then Save. The camera view should now have been rotated.
.

.

In a web browser:

The other method commonly used to access cameras and NVRs is through a web browser. You will only be able to configure the image rotation settings for a remote camera. The image for cameras connected directly to an NVR cannot be rotated in this menu due to the restricted access to the camera’s settings.

To access your camera in a browser, simply input its IP address into the browser’s address bar and hit enter. You’ll be taken to a login screen, here you’ll need to fill out the username and password combination you created for the camera when you first set it up. If correct, you should be taken to a page displaying the camera’s live video stream.

The process of rotating the camera’s image is relatively similar to that in iVMS-4200, just go to:

Configuration > Image > Video Adjustment > Rotate > On

The setting should be automatically saved, you’ll see a popup in the bottom-right corner of your window confirming this. That’s it!

.

.

.

Part 2: How do I position and rotate my camera’s lens correctly?

Rotating the camera’s image through its settings will rotate the image 270 degrees. To rotate the final video stream to the desired 180 degrees, you will manually need to turn the camera’s lens 90 degrees in the opposite direction as compensation. The entire process allows the rotated image to properly fit a 9:16 portrait aspect ratio. You’ll need to follow the below steps in order to rotate the camera’s lens.

For Domes / Mini Domes:

Domes and mini domes are the fiddliest type of camera to move and rotate the lens on. You can do this with the camera either installed or taken down. You’ll need to take the outer casing off the dome first to allow you to move the lens inside.

 .

Then, loosen the locking screw located to the right of the lens rotate to allow you to move the lens and bracket. Now twist the lens bracket (the bit that can turn surrounding the lens, see the picture below) 90 degrees anti-clockwise, so that the gap in it is in the 3 o’clock position. You should see the “90” marker in the middle of the gap once in this position.

 .

Now twist the lens (see the picture below) 90 degrees anti-clockwise, holding the lens bracket in place while doing this helps, so the “90” marker is at 12 o’clock and the “0” marker is in the 3 o’clock position. It may take a bit of wiggling and feel unnatural but the lens will move to this position, you won’t break anything!

.

Finally, rotate the lens bracket 90 degrees clockwise so that the gap is at 6 o’clock, and then move the lens so that is fits into this gap, so it looks like the picture below. This next stage takes a bit of trial and error on your part to get your desired camera view.

 .

You’ll need to fiddle around with the lens while looking at the camera’s live stream to ensure it is straight and something you’re happy with. Viewing your stream through iVMS-4200 or Hik-Connect is best as you can look at the image and remotely while fiddling with the lens position at the same time.

.

For Turrets:

Rotating the lens on a turret camera is a slightly more straightforward process. First, you’ll need to remove the trim ring (shown in the picture below) by twisting it anti-clockwise and lifting it off the base of the camera.

.

This should expose the locking screw, you’ll need to loosen this using a Phillips-head screwdriver enough for Turret’s ball to be rotated. You shouldn’t need to take the screw out entirely. All these parts are labeled in the picture below. The “UP” marker on the ball indicates the top of the camera.

 .

You’ll now need to rotate the ball 90 degrees anti-clockwise so that this marker moved from the 12 o’clock to 9 o’clock position. Now, tighten the locking screw back up and replace the trim ring to its original position. The lens should now be appropriately rotated.

.

For Bullets and Mini Bullets:

The camera models that allow for the easiest rotation of their lenses are bullets and mini bullets.

It is important to note that the sun shield on these cameras cannot be moved to be above the lens when rotated, which presents a drawback so using them for corridor mode.

 .

The sun shield will sit to the side of the rotating lens in this case so you’ll need to make sure that you shelter the camera somewhat (such as under the eaves of a roof) if setting a bullet or mini bullet for corridor mode.

Mini bullets have a locking nut (shown below) at the end of their base which will allow you to rotate the camera when loosened. Larger bullets will require you to loosen the locking screw, which is the screw furthest to the right of the base if looking at them (shown below).

Once you’ve loosened the locking screw/nut as appropriate, rotate the main body of the camera 90 degrees anti-clockwise, so that the sun shield is in the 9 o’clock position. This will rotate the lens. Once you’ve done this, tighten the screw or nut again to secure the camera in its newly rotated position.

.

.

Part 3: How do I change the layout of my camera streams to accommodate for corridor mode?

Once your camera is all set up in corridor mode, you’ll want to be able to adjust the way that you view the grouped cameras to avoid the camera’s live stream being reduced in size to fit the standardised landscape 16:9 frame. This is easily done by simply merging two of the landscape frames to make a portrait, 9:16 frame to which you can dedicate your camera.

 .

This custom view layout can be set up in an NVRs local GUI and in iVMS-4200. Please see the guides below for an explanation on how to customise your stream layout to accommodate corridor mode.

In iVMS-4200:

Click on the small icon made up of several small boxes at the bottom of your Main View screen in the program, this should bring up the window division page. Click Add to create a Custom Window Division.

.

In the Add Custom Window Division popup, set the name and dimensions of your new stream layout as desired.

Now, click and drag your mouse over the two frames you want to merge to select them both. Once they’ve both been highlighted by a surrounding red box, click Joint to merge them. Now click Save.

.

Once back in the Main View, click on the Window Division icon in the bottom right-hand corner again and select your new custom layout from the list. Your new stream layout should load ready for you to assign the individual cameras to.
.

Locally through your NVR’s GUI:

Please Note – This option is only available on NVRs that are running Version 4 firmware. There is not currently an option to customise your stream layout on K-Series recorders. If you’re running Version 3 firmware then your only option is to configure your layout as per above in iVMS-4200.

It’s also useful to be able to customise the stream layout as viewed directly from your NVR’s GUI as this is many people’s preferred method for observing and configuring their camera feeds.

To do this, firstly, you’ll need to navigate to:

Configuration > Live View > View > Set Custom Layout (small cog in bottom-left hand corner)
.

In the Custom Layout Configuration popup, set the name and dimensions of your new stream layout as desired. Now, click and drag your mouse over the two frames you’re going to merge and click the Joint button in the top toolbar, followed by Save.
.

Once back in the Live View, click on the Split button in the bottom-right hand corner of your screen. Then, select your new custom layout from the Custom Layout list that appears to load your new stream layout. You can then add the camera streams to each frame as appropriate.
.

You should now be up and running with corridor mode set up properly on your camera! Feel free to start a new thread or comment below with any other questions or suggestions. Thanks for reading!

How Do You Setup Event Pre & Post Recording for a Hikvision Camera?

To Adjust the smart event pre-record and post-record you need to follow these steps:

1) Log in to the NVR/Camera

2) Go to Configuration > Storage > Schedule Setting > Record Schedule

3) Click the ‘Advanced’ button at the top right of the record schedule
.

4) Select the duration you want from the pre/post record dropdowns and click OK
.

​

One thing to be aware of with event pre/post-recording is what Hikvision call a Buffer Zone. The buffer zone is simply a bracket of footage around the current moment in time that is continually recording/erasing, this buffer zone allows you to record only by event but still have access to footage before and after the trigger event without having continuous recording enabled.

The issue is that the buffer zone is limited to around 2-4MB of storage and so the higher your resolution and stream settings the larger the files sizes are and thus the maximum duration of the buffer you can use is limited.

So basically an 8MP camera will not be able to have as long pre/post recording durations as a lower-spec 4MP or 2MP model. (unless you reduce the resolution/stream settings of the 8MP camera)

We recommend that to get the longest duration possible from your pre/post recording you should set them to the not limited option to use the full 2-4MB buffer capacity.

(One other thing to be aware of, there is no advantage or disadvantage for pre/post recording when using an NVR. Although the NVR is managing the event recording, each channel on the NVR is still set to the same 2-4MB buffer, the same as the individual cameras. So you would not get more pre/post recording capacity with 1x 8MP than you would with 8 x 8MP cameras on an NVR.)

How do I stop my Hikvision NVR from beeping?

If a Hikvision NVR notices what it deems to be a critical error, or “exception”, it will make a constant beeping sound to draw your attention to this.

These exceptions can occur when:
.

• A hard drive has not been installed or properly formatted

• There is an error with the hard drive, it has been damaged, or the cameras are just not recording properly

• A hard drive has been filled and not set to overwrite

• There is an IP conflict, preventing the NVR from operating properly

• The NVR detects an illegal login

• The NVR loses its network connection

Of course, ignoring these exceptions are not recommended. However, you can disable the beeping while you address whatever the issue is by following the steps below.
.

.

​

Step 1:​

Connect to your NVR in a web browser by using its IP address and logging in.​

​

Step 2:​

Check what the exception that is causing the beeping is in the NVR’s logs. To find these, go to:​

​

Configuration → System → Maintenance → Log​

​

Set the log search so that the “Major Type” is “Exception”, with the start and end time covering a period when the beeping has occurred.​

​

For example, you can see that it is an IP address conflict causing it in this case.​

​

Note – Camera disconnections will not cause the NVR to beep. ​

​

​

.

Step 3:​

Go to:​

​

Configuration → Event → Basic Event → Exception​

​

Find the “exception type” identified in step 2 in the dropdown on this page.​

​

.

Step 4:​

Select the exception shown in your logs from the dropdown.​

​

You will see that “Buzzer” is ticked as a “Normal Linkage” action, which is what is causing the NVR to beep.​

​

.

Step 5:​

Untick this, click “Save”, and the beeping should stop.​

​

My Hikvision NVR has both HDMI & VGA connections, can I connect two monitors to my NVR?

This question gets asked a lot and we have always assumed that as the larger Pro NVRs (9600 Series) have 2 x VGA & 2 x HDMI that they were the only models that would support any kind of multi-screen setup.

Today we did some tests with a selection of demo NVRs we have in our office to see if it was possible to connect two monitors to an NVR that only had 1 x VGA & 1 x HDMI, below are our findings from testing K-series & I-series NVRs

K-series (DS-7604NI-K1-4P(B) / DS-7608NI-K2-8P / DS-7616NI-K2-16P / DS-7716NI-K4-16P / DS-7732NI-K4-16P)

When we connected a monitor to both the VGA & HDMI of a 7604 4-channel NVR we were able to see the usual K-series GUI on both screens at the same time, but with the older K-series GUI when viewing on two monitors your actions will be synchronised (e.g. when you move the mouse on one screen the mouse will do the same movement on the 2nd screen, and this is the same for any action whether it’s opening menus and selecting individual live streams).

 .

So the main disadvantage of this is that you can’t have different live views streaming on each monitor, both monitors will show exactly the same thing and the only difference will be that one will be a VGA quality. The advantage of these synchronised displays is if you have a setup with say a large wall-mounted monitor and a smaller desktop monitor,

 .

you can have the HDMI output to the big screen while you operate from a smaller VGA screen, this kind of setup would be useful for any situation where you need to demonstrate a feature of the NVR or play back footage in real-time to a large group of people.

I-series (DS-7608NI-I2-8P / DS-7616NI-I2-16P / DS-7716NI-I4-16P /DS-7632NI-I4-16P / DS-7732NI-I4-16P)

We have a 7716-I NVR as part of our demo system in the office and when we connected two monitors to the VGA & HDMI connections on the back we got the live streams displayed on both monitors just like we did with the K-series NVR. The difference with the I-series NVRs is that they use the latest 4.0 GUI, and on the live view page of this new interface you will find an icon in the bottom right

 .

of the screen labelled ‘AUX Monitor’ (see image below), clicking this icon allows for you to switch control between the HDMI & VGA screens and allows you to move through the NVR menus on one screen whilst keeping the cameras streaming on the 2nd screen.
.

​

Now that you have the ability to switch between and control multiple screens you would obviously want to be able to set each screen up with their own camera stream layouts, to do this simply go to the System page (cog icon at the top of the 4.0 GUI) and then click the Live View tab and select the view page from the dropdown options. On this page you can switch between the HDMI & VGA screen and set the camera stream layout for each monitor (see image below).

 .

There are limitations to how you can set the layouts, you can set the same camera to appear on both screens in the same place or in different positions and you can also spread all 16/32 cameras out across

 .

the 2 screens, the main thing you can’t do is have a camera appear in different positions when using different live view layouts on the same screen (e.g. if you put camera 1 in the top left position for the 2*2 layout it will also appear in this top left position when you switch to the 3*3 layout).
.

9600 Series, Deep in mind, and Other NVR models

We don’t tend to get hands-on with these larger, top of the range NVRs but as you will see from the product pages and datasheets for these models a lot of them have 2 x VGA & 2 x HDMI connections. We assume that the 2 x connections on these models takes the multi-screen setup one step further by allowing you to seamlessly

move your mouse between screens (like you can with a 2 screen setup on a PC), thus allowing you to adjust each screens layout with ease and see all your camera streams in full quality via HDMI connection on both screens. (be aware that you will only see the full resolution stream of each camera when you select to view main-stream)

If anyone out there on the forum has had experience using two monitors with a 9600 Series NVR (or any other top of the range NVR with dual VGA/HDMI ports) then please share any information you have in this thread.

How do I set my Hikvision ColorVu camera’s built-in light to turn on during event periods?

We’re often asked if a ColorVu camera’s built-in supplementary white light can be programmed to turn on during VCA event trigger periods, such as during instances of motion detection, intrusion detection, or line crossing detection.

After testing, we can confirm that this is now possible on all 2nd Generation ColorVu cameras (any with a ‘G2’ in the part number) and works reliably.

In effect, it means the light on the camera can be used like a PIR floodlight, but with more control over a number of variables. Notably, trigger object type (human, vehicle, or both), the motion detection area, and direction of trigger object movement.

Please see the below steps for instructions on doing this.
.

.

.

Step 1:​

Connect to your camera directly in a web browser, even if it is recording to an NVR.​

​

If your camera is connected to your local network, just use its local IP address to do this.​

​

If it is directly connected to your NVR’s PoE ports, then you will need to use the virtual host feature to connect to the camera via your NVR’s Camera Management page.​

.

Step 2:​

If you have a ColorVu camera from the G3 platform, then make sure you have installed the firmware, version 5.5.800 (build 210628), or later.​

​

If you have one of the G5 models (indicated by a ‘C’ at the end of the part number), install version 5.7.2 (build 211228).​

​

You can also check your camera’s platform when connected to it in a web browser by going to:​

​

Configuration → System→ System Settings → Basic Information​

​

The platform will then be indicated by either a “G3” or “G5” in the “Firmware Version Property” box:​

​

​

Note – Please see this guide for instructions on how to check and update the firmware on your camera.​

.

Step 3:​

Once you’ve logged in, navigate to:​

​

Configuration → Event → Basic Event (for motion detection) / Smart Event (all smart event options support this) → Select your preferred event type​

.

Step 4:​

Enable and set your event up in the Area Settings and Arming Schedule pages, this guide explains how to set up motion detection, line crossing, and intrusion detection.​

.

Step 5:​

Navigate to the “Linkage Method” page, tick the “White Light” box, and set how long that you want it to remain on for on event triggers (in seconds) in the “Duration” box.​

​

Click “Save” once this is done so the settings are kept.​

​

How do I use a Hikvision NVR’s “Virtual Host” feature?

One of the most successful selling points of a Hikvision NVR to many small-setup customers is the “Plug and Play” functionality that simplifies the setup process of their surveillance system.

However, plugging a camera directly into a port on the NVR, unfortunately, does not allow you to access the camera via its own internal LAN IP using a browser due to it being on the NVRs internal network, and this can significantly reduce the number of configuration options you have access to.

 .

The NVR does allow you to configure many options for each connected camera, but some essential features are only accessible via connecting to the camera itself (such as audio codec options). This was of course a big problem previously.

With the advent of newer firmware and models of NVR, Hikvision has introduced a feature called Virtual Host. Activating this feature turns your NVR into a “host” for the cameras allowing you to connect to them via a browser. Essentially, the NVR forwards all traffic received from your browser to the appropriate camera you’re trying to connect to, eliminating the biggest problem of plug and play functionality.
.

.

Step 1:​

First of all, access your NVR via a web browser. If you do not know the LAN IP of your NVR, download Hikvision’s tool SADP tool, which scans your network for any Hikvision devices that are connected and allow you to see and change their network settings, including the IP address.​

​

Download SADP for Windows ​

Download SADP for MacOS​

.

Step 2:​

Once you’ve logged in, navigate to: ​

​

Configuration → System → Camera Management​

.

​

.

This screen displays all the connected cameras on your NVR. Notice that the final column labelled “Connect” is currently empty. We’ll be coming back here in a moment.​

.

Step 3: ​

Now, navigate to:​

​

Network → Advanced Settings → Other ​

​

Turn on the Enable Virtual Host option.​

​

Note – Your NVR will reboot when you click “Save”.​

.

.

​

Step 4:​

Now, navigate back to the Camera Management window from earlier. You’ll notice that the previously empty connect tab now features links for each camera currently connected to your NVR.​

.

​

Step 5:​

Click on any of these links to access the respective camera via your web browser:​

That’s it, you’re done!

This should be useful when you want to access options on your camera that your NVR doesn’t feature. If you have any further questions feel free to ask, we’re happy to help.

Why am I not able to tilt my Hikvision PTZ camera upwards?

Hikvision PTZ cameras are not usually set by default to have their full range of movement enabled. This often means that cameras that are advertised as being able to tilt upwards are not able to do so straight out of the box, as this needs to be enabled in the camera’s settings.

You can check the movement range available on your camera in the PTZ section of its datasheet. Below is an example of this range shown for the DS-2DE5425IW-AE (S5):
.

​

0˚ tilt refers to the camera being in its home position, where it running parallel to the ground beneath and looking straight out at the scene.​

Any negative figure (e.g. -15˚) here refers to the angle that it can tilt to upwards of the 0˚ position.​

Any positive figure (e.g. 90˚) refers to how the angle of tilt available below this 0˚ position.​

​

Cameras with “auto flip” will rotate 180˚ and then flip their image when it reaches its full 90˚ downwards tilt, which will give the illusion of you having a full 180˚ (or more) range when you try to continue to tilt beyond this 90˚ position.​

To change the movement range currently set on the PTZ, you will need to connect to the camera directly in a web browser.
.

NB – If your camera is directly connected to an NVR’s network ports, then you will need to use the Virtual Host feature to access the camera’s backend. If it is connected to your local network, then you can just browse for its IP address to do this. ​

Then, go to:
.

Configuration > PTZ > Basic Settings > Max. Tilt Angle​

​

​

You should have some different options in this dropdown, depending on the maximum tilt range of your camera. If you want to enable the complete range of movement, then select the option with the largest range between the two figures (in this case, “-15 – 90˚”).​

Once you have chosen an option that you’re happy with, make sure to click “save” at the bottom of the page so that these changes are updated on the camera.

How do you Shutdown a Hikvision NVR?

This is a common question by Hikvision users so we thought we would create a short forum post to give a clear answer on the possible ways to shutdown an NVR.

Direct Monitor Access
If you are accessing your NVR from an HDMI/VGA monitor then it is possible to shutdown the NVR from within the menus, depending on the NVR model the menus and shutdown process is slightly different as you will see from the below explanations:

I-series (76xxNI-I2 / 77xxNI-I4 / 96xxNI-I8 / 96xxNI-I16) & K-series (7604NI-K1/4P(B) / 76xxNI-K2 / 77xxNI-K4) NVRs – In the top right corner of the live view you will see a power icon which if you hover over will bring up text that says either ‘Power’ or ‘Power Off’, click the icon and a pop-up menu will appear with 3 options, one of which will be shutdown.

Click shutdown and a box will appear saying ‘shutting down…’ and then after 20-30 seconds, new text will appear asking you to switch the NVR off at the back to complete the shutdown.

(Above is for I-series and K-series NVRs that are running 4.0 GUI and EUI GUI respectively, if your NVRs are running older firmware and not using the latest user interface you will need to follow the below instructions)

7604NI-K1, E-series (76xxNI-E1 / 76xxNI-E2 / 77xxNI-E4), SE-series, and other older generation NVRs – Right-click the live view page and select the main menu from the dropdown, one of the menu options should be clearly labelled ‘Shutdown’ which when clicked should bring up the same 3 options as mentioned above.

Click ‘Shutdown’ and a window should appear with the text ‘shutting down…’ and roughly 20-30 seconds later new text will appear asking you to switch the NVR off at the back to complete the shutdown.

Browser Access
if you are accessing the NVR primarily from a browser then your only option for shutting the NVR down is to simply flick the switch on the back of the NVR because the browser menus do not include a button to shut the NVR down like you can with the direct monitor.

How do I know if the lens on my Hikvison mini dome is orientated correctly?

It’s easy to install your Hikvision mini dome only to turn it on and find that the image is upside down. If you’re not familiar with Hikvision cameras, adjusting the lens and settings can be confusing. This post will explain the two different ways that you can rotate your camera’s image by:
.

1.Manually rotating the lens itself.

2.Rotating the cameras image 180° in the image settings.

Part 1: How do I orientate my camera’s lens manually?
.

1.Remove the mini dome’s cover by loosening the screws surrounding the glass dome, shown in the image below:

.

2.You should now be seeing something like the image below. Loosen the locking screw to the right of the lens, and then the lens bracket which locks the orientation of the lens in place. The lens is effectively attached to the camera body via a ball and socket joint, so this can be orientated however you like.

Part 2 of this guide explains rotating the lens in more detail, as well as how to rotate the lens on the turret and bullet styles of camera – How-to: How do I set up Corridor Mode on my Hikvision Turret, Bullet or Mini Dome IP CCTV camera?

NB – This image shows a camera with the lens rotated 180°, you’ll actually need this 90° marker to be in the 3 o’clock position, and the 180° marker pointing towards the bottom of the unit.

Hata! Dosya adı belirtilmemiş.

.

3.The lens should be positioned like the one shown in the below image. The small line marker located directly parallel to the 180° marker signifies the top of the lens. So, this needs to be pointing up, towards the top of your scene. This will orientate the camera’s view correctly. You should also make sure that the lens bracket is repositioned correctly so that the thicker part surrounds the top half of the lens.

.

4.Now, tighten the locking screws and fasten the dome cover back in place, making sure the cover screws are tight to prevent water ingress into the camera. It’s always worth checking your camera stream before doing this to make sure that the camera view is orientated as you like.

For a guide on installing you Hikvision IP camera correctly to ensure it is properly waterproofed, please see this guide – Please Read: IMPORTANT – Installing Hikvision IP Cameras Correctly

Part 2: How do I orientate my Hikvision camera’s view through its settings?
.

1.Log into your camera’s web browser interface (not your NVR’s), by entering its IP address into the browser’s address bar. This will only work for cameras that are on the same LAN as your PC. If the camera is directly connected your NVR’s PoE ports, then you will need to use the NVR’s ‘VIrtual Host’ feature to access the camera’s own browser view, which gives you access to a wider range of settings.

NB – It is recommended that you use Internet Explorer if possible. If you are a macOS user, the best web browsers for this seem to be Google Chrome or Apple’s Safari. You might need to install Hikvison’s macOS Web Plugin as well.

2.When you have access to the cameras in a web browser, go to:

Configuration > Image > DIsplay Settings > Video Adjustment

The different options are will adjust your image as described below:

Left/Right: The image will be flipped horizontally, so it appears as a typical mirrored image.
Up/Down: The image will be flipped vertically, which will still show a mirrored image of the default view as you are not actually ‘rotating’ the image 180°
Center: This will be the option that you need to select to rotate the image 180°, which will show the same view as physically rotating the lens would.

If you only need to rotate the image 90°, then setting the Rotate option to ON will do this, as shown below.

To rotate your view 270°, set the Mirror dropdown to Center, and then set Rotate to ON.
.

Thanks for reading – hopefully, this will prove helpful to some of you in the future! As always, please feel free to post any questions or feedback that you have below or by creating a new thread.

Hikvision Password Reset Options – 4 Ways the User can reset their Passwords

The new video from Hikvision (linked below) takes you through the 4 password reset options that the user can do themselves, these are:

1. Reset Password by reserved email
2. Reset Password via Hik-Connect App
3. Reset Password via Security Questions
4. Reset Password via GUID File

IMPORTANT: Not all of the above options will be available on all Hikvision products, also be aware that all the above options do require some level of pre-configuration to use them so if you have done none of the setups explained in the video you will have to follow the traditional reset file method as described here (remember though that we at use-IP will only reset passwords of our own customers)

How to Set up the Hikvision 2nd Generation Modular Intercom

We get asked a lot of questions by people looking to buy or who have already bought Hikvision’s 2nd Gen modular Intercom solution and for a long time, we have had to take the majority of those questions to Hikvision Support as we just don’t have enough hands-on experience with the intercom solution to answer them confidently.

Now we have finally found time to get a demo intercom system set up, test some of the features, and give you a guide of how to get a basic intercom solution up and running.

The below guide will initially** be split into 3 key sections with multiple sub-sections:

Single Module Setup (Video Intercom Module)
.

• Setting up the Video Intercom Module

• Setting up the Indoor Station

Three Module Setup (Video, Indicator, Keypad)
.

• Sub Modules & Dip Switches

• Setting Room Numbers & Unlock Codes

Six Module Setup (above + Display, RFID, nametag)
.

• Nametag & Display Modules

• Card Reader Module

The reason we have decided to cover it this way is that the modular nature of the solution means there are too many variations to cover specifically, so instead we will cover the details of the 3 most common setups and once you know the basics of all 3 any combination of modules should be achievable.

(**IMPORTANT – This will be a continual work-in-progress thread and we will add new posts with explanations of new features & settings as we test the intercom further and learn things from customers & Hikvision Support, this initial post will basically be a contents page for the entire thread)

Will the smart tracking feature on a Hikvision PTZ camera allow it to zoom in to its maximum zoom ratio automatically?

We’re frequently asked if Hikvision PTZ cameras will automatically zoom in to their maximum ratio when they are automatically tracking a target. After talking to Hikvision, we found out that you’ll need to do the following to enable the camera to do this:

On the camera’s menu (via a web browser) navigate to:

Configuration > PTZ > Smart Tracking

Here, set the Zoom Ratio to its maximum value, which will then allow the camera to automatically zoom to this maximum ratio.

Do It Youself – How To Silence a HikVision DS-7608NXI-I2/4S AcuSense NVR

Hi Guys,

I’m new to business here, but have made a video tutorial to decrease fan noise on my AcuSense 7608-NXI-i2-4S device. Maybe this helps others as internal construction of many NVRs from HikVision seems to be almost the same.

I also have some questions towards the community.
1. What is my latest firmware available for my NVR?
It is an AcuSense 7608NXI-i2-4s, but as I see it is not a full i-series device.
i-series are up to 4.22, but mine seems to be different. Can I use firmware here or not: Firmware – Latest HikVision Firmware for I-Series NVRs – V4.22.005

2. Scene change detection+alarm seems to be problematic. My cameras are AcuSense 2086G2 Bullet, but they do only detect scene change when going completely dark scene to normal recording scene. If I let them record a normal scene situation and then simulate a camera removal from wall situation – camera does not trigger a scene change event.

How to update the Hik-Connect App on your Android phone using Hikvision’s App Store

The method for updating the Hik-Connect App on Android devices has recently changed to mean that users can no longer update via Google’s Play Store. To use Version 4.1.0 of the app Android users now need to access Hikvision’s own App Store and update via the .apk file which is downloadable from there. The reasons for this change have been discussed in this post, as well as our thoughts on the situation.

This simple tutorial has been put together to walk you through this new method for updating in 5 easy steps, so that you can ensure you install the latest version of the Hik-Connect app is installed properly on your Android device.

Step 1:
Open Hik-Connect if you have it already installed, and press the Upgrade Now button in the popup. If you don’t have the app installed or do not get this popup upon opening the act, this link to the Hikvision App Store will take you to the update file.

You need to make sure you open this page on the Android device that you wish to install the updated software on, as this will be the device that the update file is saved to! In the App store, make sure Android is selected in the top-left hand corner and then select Download beneath Hik-Connect to get the .apk update file.
.

Step 2:
Press Download when the prompt to do so appears at the bottom of your screen. Don’t worry, this is a safe and secure link!
.

Step 3
Select Install when the prompt to do so appears at the bottom of the screen.
.

Step 4
The installation will begin, wait for the progress bar to complete… Go and put the kettle on!
.

Step 5
If you get the same screen as the one below, then you’re all done. You should now have the latest version (V4) of Hik-Connect installed on your device. You can either press Open to launch the app, or Done to return back to whatever you were previously doing. If your screen doesn’t say App installed with a tick above, then you’ll need to repeat steps 1-4 again!
.

How do I set up an alarm to work with an external device on my Hikvision NVR?

We often have customers ask us “how do I get my new NVR to work with an existing alarm system I already have installed” or “how do I connect something to the IN/OUT ports of my NVR?” Indeed, for such an important feature for the NVR’s to have, it is not the most straightforward to get set up with.

We thought it would therefore be useful to put together this guide to walk you through how to configure the alarm function, either through locally through your NVR and monitor, or through Hikvision’s iVMS-4200 software, in 10 easy minutes.

.

Contents:

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?​

Part 1: How to wire my alarm system into my NVR’s alarm input and output ports?

As daunting as it may seem when you look at the multiple different alarm ports in the back of your NVR, this part is simple enough once you know what you’re doing. If you’re struggling to find you alarm IN/OUT ports, they are the block of green connections which should be labeled as “ALARM IN/OUT” on the device.

The number of connections will vary here depending on the size of your NVR, the picture shown is of a smaller Hikvision DS-7608NI-K2-8P 8 Channel NVR. Larger NVRs will have more of each connection, but nonetheless, the process is the same.

Firstly, make sure you can locate the NVR’s “ALARM IN ” and “ALARM OUT ” ports, with their corresponding “Ground/G” ports. If you’re connecting a device to trigger your NVR cameras with an external event (e.g. a smoke alarm, PIR senor etc) then you’ll need to run the wires from the device into one of the input ports and its corresponding ground port.

If you’re connecting a device to be triggered by a smart event set up on your NVR (e.g. a siren or warning light), then connect the wires to the output port and corresponding ground port. All the ports are marked up in the picture below but should also be clearly labelled on your unit.
.

Part 2: How do I configure the alarm function settings of my NVR locally via a monitor?

Now that all the necessary connections are made, you’ll need to set up your NVR’s alarm function for it to alert the alarm system that you’re connecting to it.

Firstly, I’ll show you how to do this locally. You’ll need to boot up the NVR, once in the menu, navigate to:

Menu > Configuration > Network > General

Here, you’ll need to insert your network’s IPv4 address, IPv4 subnet mask, IPv4 default gateway and your preferred DNS server:

.

• If you’re unsure of your IPv4 address, subnet mask or default gateway, our tutorials on How To find your router and PC’s IP address using a Windows PC or How To find your router and Mac’s IP address using a Mac show you how to do so. Please note, you need to make sure the PC you use to find these is hard wired via a network/Ethernet cable do make sure this turns up the correct addresses for your network/router.

• Unless you know of a preferred DNS server that you’ve set up yourself, Google’s public DNS server address (8.8.8.8) should work fine. It’s worth entering an alternate backup DNS too beside Alternate DNS Server, Cloudflare’s public DNS address is a good option (1.1.1.1). Follow this link for a list of the best publicly available DNS servers.

Now, navigate to:

Network > Email

At this screen, you’ll need to fill in all the fields as appropriate to your Email account. If you’re unsure of these, then complete the fields as below:

Enable Server Authentication: Tick/check this box
User Name: Insert your email address here
Password: Insert the password you use to access this email account
SMTP Server: If you don’t know this, follow this link for “finding your SMTP server address”
SMTP Port: Insert either 25 or 587 here
Enable SSL: Leave this box unticked
Sender: Insert the first part of your email address (everything before @)
Sender’s Address: Insert your email address here
Select Receivers: Insert “Receiver 1/any name” here
Receiver: Insert your email address (same as Sender’s Address)
Enable Attached Picture: Tick/check this this box, it will mean that you’ll receive picture of anything that triggers your cameras’ alarms in an email.
Interval: Insert 5s (5 seconds)
.

When you’ve completed these fields, navigate to:

Menu > Camera

Ensure all your cameras are properly connected to the NVR and are visible on this screen. If you haven’t yet added any cameras to your NVR, this guide on adding Hikvision cameras to an NVR walks you through how to do so.
.

Now, navigate to:

Menu > Configuration > Alarm

This should take you to the Alarm Status menu. This menu lists the status all your alarm IN/OUT ports and any alarms that have been configured/assigned to these ports.

You’ll need to use this screen to check that you’ve set the correct Alarm Type for the alarm/device that you’re connecting. The options you have are N.O (Normally open) and N.C (Normally Closed). In brief, N.O alarm types use switches/sensors that normally remain open with no current flowing through them, so closing the switch allows for the flow of current and activates the alarm.

N.C alarm types, on the other hand, use switches/sensors the normally remain closed with current flowing through them, so opening the switch stops the flow of current and activates the alarm. There’s a lot to be said about N.O and N.C alarms but for now, you only need to know which category the alarm that you’re using falls under. If you want to take a journey down the N.O vs N.C rabbit-hole, I found this article on the differences between N.O vs N.C useful.
.

To assign an alarm to one of these IN/OUT ports, navigate to:

Alarm > Alarm Input > Settings (click on the small cog) > Trigger Channel

Choose the channel that you would like to trigger your alarm. In this case, we’ve selected channel 1.
.

Now, navigate to:

Settings > Arming Schedule

Select the hours that you would like to schedule your alarm to be turned on for. Typically, this would be 24/7, so set the schedule for Monday, Week 1 as 00:00-24:00. Now, copy this schedule to the rest of the week by clicking Copy and then checking the box for All in the popup window. If you only want your alarm scheduled for certain days, then select the specified days in this popup from the list of 1-7 (1 = Monday, 2 = Tuesday etc).Once you’ve done this, click Apply.
.

Finally, navigate to:

Settings > Linkage Action

Tick the boxes for Notify Surveillance Center and Send Email and then click Apply so that you email notifications whenever the alarm is triggered. If you have connected a separate device to be activated by the alarm in the NVR’s Alarm OUT port, then ticking the box for Trigger Alarm Output will activate this device when your alarm is triggered.
.

That’s it for the local setup section of this tutorial! Your NVR’s alarm function should now be set correctly.

Part 3: How do I configure the alarm function settings of my NVR remotely via iVMS-4200?

The first thing you’ll need to do is ensure you have the most up to date version IVMS-4200 installed and that you’re able to view the live feed of your camera(s) through the software.

If you haven’t already added your NVR to the program, navigate to:

Maintenance and Management > Device Management > Add
.

Add your NVR here by filling out the fields in the popup window, ensure the boxes beside Export To Group and Synchronise Time is checked and then click Add.
.

Now find the NVR on your device list and select:

Remote Configuration (the small cog listed beside your NVR) > [Basic Settings] > Event > Alarm
.

NB the configuration menu layout you will see henceforth will vary between two depending on the model of NVR that you have. I have included both variations for each step, so don’t worry if some of the below screenshots look unfamiliar.

Fill out the alarm parameters here, e.g. as follows:

Alarm Input: Select your NVR’s channel that you would like to trigger your alarm (e.g.: A<-1)
IP Address: Local
Alarm Name: Name your alarm as desired
Alarm Status: Normal/Remain Open or Normal/Remain Closed depending on the type of alarm, see the first half of this tutorial to understand the differences
Enable Alarm Input Handling/Enable Alarm Linkage Actions: Check this box
Arming Schedule: All-day Template
.

.

Open Arming Schedule, pick an arming template or a custom schedule of hours that you want your alarm active for.
.

Now, Click Settings beside Linkage Method. Check the boxes for Notify Surveillance Centre, Email linkage and Trigger Alarm Output (if you’re connecting an external alarm device to an output channel), then set the desired Triggered Camera.
.

.

Click Save, and then Save again in the alarm configuration window.

Switch back to Main View and select your NVR from the side panel.

Now, click the small alarm picture and speaker icons at the very bottom toolbar so that they’re both enabled and look like the second image below. This will enable the alarm’s function to send an image of its trigger, as well as the audio.
.

That’s it for the remote setup! It’s always worthwhile testing your alarms to check everything is now working as it should be.

If you have any questions or comments to make, please do so in a separate thread mentioning this tutorial and I’ll get back to you as soon as I can.

How to Unbind a Hikvision Device using SADP on a PC

Unbinding a Hikvision device is not something that is required all that often, in most cases you can do the unbind from within the app. There are though some rare cases when the user does not have access to the Hik-connect account that the device is bound to, for example, if you have purchased a used device that has not been properly disconnected from its previous owners Hik-connect account or if you added the device to an employee’s account and they leave without removing the device from the app correctly.

As long as the Hikvision device has been set up correctly on your local network, then the process of unbinding should be pretty simple:

Step 1 – Open SADP on a PC
Step 2 – Click Refresh and select the device you want to unbind by ticking the box next to the device on the far left of the list
Step 3 – Click Unbind
Step 4 – Enter the current username and password of the device (this is NOT the username & password of the Hik-connect user you are trying to unbind the device from)
Step 5 – Enter the Verification Code and click confirm

You should then see a quick pop-up with a green tick saying Unbind Successful, If the device does NOT unbind and you get an error message like “The device is Offline” or “connecting device failed” then the most likely problem is that your DNS settings for the device are not set correctly.

You can change the DNS settings by logging in to the device using a browser and go to Configuration > Network > Basic Settings > TCP/IP and you will see the 2 DNS boxes at the bottom. We recommend that if you are unsure of what DNS to use that you enter default/most commonly used DNS servers which are shown below:

Prefered DNS – 8.8.8.8
Alternative DNS – 8.8.4.4

Once you have saved these DNS settings the unbind process should work

How do I update HikVision Firmware in just nine simple steps?

Updated 20-2-19 – corrected the link to the portal as Hikvision changed their url (again). Otherwise all is good. We use this method every day. Now viewed over 38,000 times.

Here’s how to upgrade your HikVision camera or NVR to the latest firmware version in just nine simple steps:

Step 1: Download the latest HikVision firmware to your PC.

Step 2: Extract the digicap.dav file (which is the actual firmware file) from the zipped file you downloaded.

Step 3: Copy that digicap.dav file to your PC’s root folder e.g. C://

Step 4: Browse to your NVR, camera, etc – using Internet Explorer:

Step 5: Login and navigate to Config -> Maintenance (screenshot attached below)

Step 6: Scroll to the bottom of the screen you’ll see Upgrade Firmware.

Step 7: Click the Browse button at the right-hand side.

Step 8: Browse to and select the digicap.dav file in your C:// drive

Step 9: Click ‘Upgrade’.
.

I have seen reports that you cannot leap updates, but not encountered the problem myself for some time (applies to old firmware of older models). If you do not succeed in upgrading from your current version to the latest version in a single step, please try interim releases.

Additional helpful tips:
.

1.Use a PC

2.Use a wired connection – PC and camera/NVR wired to your network

3.Use Internet Explorer browser (not Edge)

4.Move the digicap.dav file to your C:// folder (root of your HDD)

5.If you select/download firmware for the wrong camera family or device you will see an error message which states – “The type of upgrade file mismatches”

If you need any help finding the latest Hikvision firmware for your device:

Tutorial videos from HikVision Technical Support:

HikVision Firmware Update using Internet Explorer on your PC

HikVision Firmware Update using a monitor connected to your NVR

NVR Firmware update using a USB memory stick

Upgrade devices using IVMS-4200

NB We cannot guarantee outcomes – if you are one of our customers you will of course have our full support. We have only ever supplied official UK version HikVision cameras & NVRs. If you sourced your HikVision products from another supplier you may want to check their recommendations.

How To Set Up Live View & Playback Audio on Hikvision Cameras

There is a small selection of Hikvision cameras that support some sort of audio – audio I/O, built-in mic, 2-way audio – but on multiple occasions, customers have come back to us saying they are getting no audio on live view or playback. So to avoid this problem in the future we are creating this post to take you through the steps that must be completed to get audio from a Hikvision camera.

Step 1 – Update Firmware

Keeping firmware up to date is always important so it is always where we start with any issue, now most firmware should support the audio but if you’ve had a model for several years and never updated it you are likely on an old firmware and so updating just removes any potential problem that might be caused by out of date firmware.

EU Firmware Portal
UK Firmware Portal

The most common audio cameras will be EasyIP 2.0+ (2xx3G0) and EasyIP 3.0 (2xx5FWD/2xx5G1) which all use the same G1 Firmware.

Step 2 – Video & Audio

Login to the camera, go to the Configuration page and open the Video/Audio menu where you will see all the video settings. The important one for audio is the Video Type which needs to be changed from Video Stream to Video & Audio as shown below:
.

​

Make sure you also switch the Video Type of any other streams you are using, the main one for most cameras will be the sub-stream which is used when viewing the camera from the Hik-connect app. Also, if your camera is connected to a Hikvision NVR make sure to check the camera is set to Video & Audio in the NVRs Video Settings.

Step 3 – Audio

The final Settings to check are the Audio settings which more often than not out of the box is set up correctly and should look like the below screenshot:
.

​

The only setting that might change depending on the model you have is the Audio Input option. If you have a camera with only a built-in mic or 2-way audio then the only option you will have is MicIn, but if the camera only has audio I/O connectors or has both options then you will have both MicIn and LineIn input options. Make sure if your camera has both options that you select the correct input for your setup, LineIn will be used if you have a more powerful audio device connected like an amplifier or a stereo microphone, while MicIn will be for smaller standard Mono microphones.

With all 3 of these steps completed, you should now have live audio from the camera on the browser, app, and direct monitor live view, but there is one final step to have your camera record audio.

Step 4 – Record Audio

Login to your camera/NVR and go to Configuration > Storage > Schedule Settings and select the camera with audio, once you have the schedule for that camera onscreen you will need to click the Advanced button which you will see in the top right of the schedule. A pop up will appear and you will see an option to Record Audio, tick this option and click OK to apply the setting, now all the recorded footage from that camera will have audio.
.

.

.

.

Support log in with cloud technology

Support real time live view

Support remote playback

Local recording and play

Support snapshot and pictures searching

Support bidirectional talk

Support PTZ control

Support scanning serial number by QR code

Support cloud user register and modify

Support remote device add, edit and delete

Support local device add, edit and delete

Support adding device by address

Support manually searching device in LAN

Support version updating automatically

Support searching device function by shake

Why can’t live view the videos on mobile APP or PC Client VMS

1.Please make sure that your DVR system is already connected to the router through ethernet cable successfully

2.Please go to Main Menu > System > Net Service to check the network is connected or not, Cloud should shows: connected 

3.Make sure the way you add device to your mobile app or PC client with correct serial number and password

Serial number: “Main Menu–Advanced–Version”

Password: DVR login password 

Hiseeu XMEYE DVR SECURITY SYSTEM ADVANCED GUIDE

Read More : XMEYE DVR User Manual

What should I do If I forgot my DVR password

1.Right click mouse from home screen, Click “Log Out–>Log Out”

2.Then click “Forget password” ＞ “Forget answer ” ＞ Then you will see two “QR code” on the monitor

3.Open your Mobile APP “XMEye Pro” , 

(1). Click the “+” icon on the top right corner—>Hit “NVR”

(2). Click “Forgot your device password”–> Scan the QR code (CAPTCHA on the TV monitor)

(3). Scan the QR code shown on your TV monitor. You will get the verification code.

(4). Input the code in “CAPTCHA”