Hikvision NVR 5.0 Professional Installation Guide

Hardware Installation

Software Configuration

Additional Resources

Important Note: The provided steps serve as a general guideline. Specific configurations might differ based on your NVR model. Always refer to the official user manual for detailed instructions and advanced functionalities.

Setting up a Hikvision NVR (Network Video Recorder) involves several steps, including hardware setup, network configuration, and camera configuration. Here’s a detailed guide to help you set up your Hikvision NVR 5.0:

1. Hardware Setup

Step 1: Unbox and Connect Components

Step 2: Connect the NVR to a Monitor

Step 3: Connect the NVR to the Network

Step 4: Connect Cameras to the NVR

Step 5: Power Up the NVR

2. Initial Configuration

Step 1: Boot Up and Log In

Step 2: Set Date and Time

Step 3: Network Settings

3. Adding Cameras

Step 1: Detect and Add Cameras

Step 2: Configure Camera Settings

4. Recording Settings

Step 1: Set Up Recording Schedule

Step 2: Configure Storage Settings

5. Remote Access Setup

Step 1: Enable Hik-Connect

Step 2: Port Forwarding (if necessary)

Step 3: Mobile App Setup

6. Final Steps

Step 1: Test the System

Step 2: Backup Settings

Troubleshooting Tips

This guide should help you set up your Hikvision NVR 5.0 system. For more detailed instructions, refer to the user manual or the Hikvision support website.

.

Our IP camera can connect directly to your network or computer, and there are three ways to do so. The three ways listed below do not require a NVR. A NVR, or Network Video Recorder, is the device that IP cameras connect to.  The NVR records video provided by the IP cameras to a hard drive, either in HD (720p, 1080p), 2K HD, or Ultra HD (4K) depending on the type of NVR and type of camera that’s being used with it.

IP cameras are network-based cameras, however they don’t require Internet access in order to be used as they are standalone devices that can be used on a local network. A simple local network can be either of the following:

1.An IP network camera connected with a network cable to your desktop computer’s network port.

2.An IP camera connected to a router that is connected to a desktop or laptop computer, but the router is not connected to the internet.

Only if you want to view your system remotely from the internet then you would have to connect the system to the Internet.

Do I need a NVR for my IP security camera system?

A NVR is not necessary in order to view your network cameras or even record video. If you are testing cameras, looking for a temporary setup or want to set up something inexpensive then using a computer with an IP camera is a good alternative to a NVR.  SmartPSS is our computer software program that allows PCs to view and record IP cameras. However, this kind of processing will demand a lot from the computer. Most likely, you wouldn’t be able to use that computer for personal use as it would be bogged down processing video from high resolution IP network cameras.  Also, computers can be unreliable and crash, potentially leaving you with no recorded video.

NVR products are standalone devices using a Linux operating system which is known to be rock-solid and crash free, and designed to be operate 24/7 and maintain system security with user account access permissions. For a complete security camera system, you will want to use a NVR along with cameras. SmartPSS software can be used as a client software to connect from a computer to a NVR to watch cameras connected to the NVR and to playback/download recorded security footage.

How to Connect IP Camera Guide 2024

Three ways to connect an IP camera to a computer

Before we begin, it is important to understand that network camera systems require the ability to transport video and power to work correctly. Power Over Ethernet (PoE) is a technology that transmits video/data signal and power over one Ethernet cable. In situations where PoE isn’t available, a 12V DC power adapter will be necessary to supply power to the camera.

Secondly, you will need to use our IP finder Config Tool to find cameras on your network. For more info on basic networking knowledge as to how IP addresses matter when deploying network cameras, please read our guide about connecting security cameras to the internet.

Now, let’s discuss the three ways to to connect to an IP camera from your computer.

1.12V DC power adapter with a network cable straight into a PC

2.12V DC power to camera + network cable to router

3.Camera to PoE Switch or PoE Injector

How to Connect IP Camera to Computer

1) 12V DC power adapter with a network cable straight into a PC

a) For this method we will provide power to the camera using a 12V DC 1amp power adapter that plugs into a 110V AC outlet. Below is a picture of our trusty power adapter.

b) Next, connect a network cable from the camera to your computer.

c) Set your computer’s network port to a static IP address like 192.168.1.200 so you can talk to the camera. Here’s how you do it on a Windows Computer:

d) All newer cameras with firmware from 2018 and onward have stringent password rules that require initialization before making any configuration changes to the camera including the IP address. In order to set the password and password recovery email address you must login to the web interface of the camera. Be sure to note down and keep the credentials you are setting in a safe place that you will remember.

There are no master reset passwords for our equipment. If you forget your password, recovery email address, and security questions that you set on the camera at time of initialization, resetting the camera requires factory service which will incur out-of-warranty costs to reflash the camera.

.

e) Once you have a static IP address assigned to your computer’s wired network port, turn off WiFi on your computer. You can find the camera’s current IP address by using the Config Tool as shown. Our test camera has a current IP address of 10.1.1.65. If you need to change the IP address to let’s say 192.168.1.120, you can do that by clicking on the pencil icon to edit.

Note: if you have a password other than admin set on the cameras, then you will need to enter that in the “search settings” options before attempting to edit the IP address. See the illustration below on how that is done.

f) As explained in our article connecting security cameras to the internet, for two devices on a network to talk to each other, they must have the same IP address scheme. In 1C we set our computer’s address to 192.168.1.200, so we need to set change this camera’s address to 192.168.1.X where X is a number between 2 and 254, and not same as the our computer’s current address. We picked 12, so below is a screenshot of what to set your camera’s ip address to if you are following along in our guide. Set the subnet to 255.255.255.0 and gateway to 192.168.1.1.

g) After changing your camera’s IP address to one that matches your network, type the new IP address of your camera into the URL of internet explorer. Here’s a brief example:

You can also view the camera using our PC software. If you don’t already have it, you can download SmartPSS from here. Here’s how if you already have SmartPSS installed.

In summary, the above is a quick and easy way to connect an IP camera to a computer with a hardwired network port. This is great for the following scenarios:

• You don’t have a router and want to set up a closed circuit system between a computer and a security camera.

• You are trying to test an IP camera or troubleshoot it.

• You are trying to connect to a security video recorder directly from a computer.

Most computers have only one network port, so this method can be problematic as it would use up your only network port, preventing you from having a hard-wired Internet connection. The next 2 methods will demonstrate how to set up a network camera on a network. Method 2 is for setting up a camera with a 12V DC power supply and Method 3 entails using a PoE injector or switch. The only different between these two methods is how power is supplied to the camera.

2) 12V DC power to camera + network cable to router

This method will show you how to connect an IP camera to your router and view it over a network, while supplying power to the camera using a 12V DC power adaptor.

a) Connect a 12V DC power supply to your camera and connect the power adaptor to the wall to power the camera.

b) Connect a network (Ethernet) cable from the camera to the router to establish a data connection between the camera and the router.

c) Give the camera about 2-3 minutes to boot. Use our IP Finder Config Tool to find the camera on your local area network (LAN).  Below is a screen shot of how it looks in our case.

The camera currently has an IP address of 10.1.1.65. As explained in our article connecting security cameras to the internet, for the camera to be reachable from the computer on your network, its IP address has to match the IP scheme of your network. In our case our router IP is 192.168.1.1, so we are going to have to change the IP address of the camera. To change the IP simple press the pencil icon to edit.

d) We are going to set the camera to an IP of 192.168.1.X, we chose 192.168.1.12. Before we go ahead and change the IP address, we have to think about duplicate IP addresses on the network which would create networking issues. To see if a specific IP address is available on your LAN, use the command prompt in Windows to ping the address you intend to use. Below is a video explaining how to use the ping command. You can use this command on Mac as well by using the terminal.

e) Let’s change the IP address. In our case we set it to 192.168.1.12. Subnet mask is usually 255.255.255.0 on simple networks, and the gateway is the IP address of the router. Press OK.

f)  Once the camera is assigned a new IP address, you can access the camera using your Web Browser or SmartPSS as shown in 1F above.

3) Camera to PoE Switch or PoE Injector

We discussed that PoE supplies power to the camera, so a 12V power adapter is not necessary in this scenario.

In this method you plug an ethernet cable from the camera to a PoE port on a compatible PoE switch or injector. The PoE switch or injector connects to the router.

Here’s how you connect to a PoE switch.

Here’s how you connect to a PoE injector

Again, use the Config Tool to find your camera’s IP address and change it to match your network scheme (if necessary) as described in steps 2C thru 2E. Once the camera is on the same network as your computer you can login and watch the camera as shown in Step 1F.

.

Summary

At this point, you now should know a good amount about networking and have used the above mentioned steps to make your very own IP camera system using your computer and IP camera.

Viewing an IP Camera on a Smart TV

Among the many different ways that security cameras are used, we are often asked if it is possible to view an IP camera directly on a Smart TV without using a NVR recorder. With most Smart TVs on the market there is no application that is available to watch IP cameras directly on the TV. In this guide we show how to use an Android TV box by downloading an App to connect an IP camera to a Smart TV or any monitor that has an HDMI input.

All IP cameras from CCTV Camera World support a RTSP video stream that is usable by third party programs and apps. The App that we suggest you use on an Android TV box is called VLC Media Player. You can login and access the RTSP stream from an IP camera and have it display on a TV.

Keep in mind any device that can download VLC Media Player can do this process like iPhones, iPads, Android tablets, and phones.

What equipment is needed?

Here’s the list of all the equipment that is needed to connect an IP camera to a Smart TV.

1.IP camera from CCTV Camera World

2.PoE injector or 12V DC Power Adaptor to power the camera

3.Network cables to connect the camera to your computer network

4.Android TV Box from any online shopping marketplace

5.Computer network to connect the camera and Android TV Box

6.Internet connection to setup and install Apps on the Android TV box which can later be removed after the setup process is finished

7.SmartTV or Computer Monitor with HDMI input

.

How to connect IP security cameras to an Android TV Box

Before you can access the stream from the camera you will need to have it connected to your computer network and verify that it’s accessible. If you purchased a standalone IP camera from CCTV Camera World the camera is likely already configured with an IP address. Check the top of the camera box for the login information label. If the camera has not been configured, or you need to set it up on your network we recommend following our How to Connect an IP Camera guide.

You will also need to set up your Android TV box on your network, consult with the manufacturer of your box to find out how to do this.

You will need your IP address, username, and password that is set on the camera in order to access it. Inside of the VLC Media Player app you can access network streams. Inside of the app navigate to adding a video source and select network stream. Using the example RTSP stream below plug in the information for your camera’s IP address and type the text into the media player URL.

rtsp://192.168.1.109:554/cam/realmonitor?channel=1&subtype=0

After you’ve typed in the correct RTSP stream for your camera you will be required to login to your camera stream. Type in the username and password for your camera to allow the app to login to your camera stream.

If you receive an error, double check that your camera is connected to the network and you’ve typed the correct username and password. Provided the camera is set up on the network and you are able to login you should now see your camera stream inside of the VLC Media Player App.

Keep in mind that Smart Camera features cannot be used with the RTSP stream. If you would like to use Smart Detection features that your security camera may have, you will want to use an NVR to display the camera on your TV.

Watch our video below that shows the setup process described above on an Android TV box.

.

.

Unlimited Access Anywhere, Anytime

When you combine our “Blue Line” IP Cameras with one of our compatible IP camera network video recorders you can keep an eye on your assets no matter where you are. Take advantage of the free remote viewing app to view on your cell. Use the free software to view and control you cameras on your tablet, or computer. Stay connected and have peace of mind knowing you can monitor your cameras remotely, without any additional monthly fees.

LATEST FIRMWARE UPDATES FOR YOUR DEVICE

UPDATING YOUR SECURITY CAMERA FIRMWARE

Firmware Updates

In order to do a firmware update you must first identify the EXACT model number of your DVR or NVR unit. The model number can be found on the sticker located on the bottom or side of the unit. All CCTV Security Pros model numbers begin with the prefix “CSP” (Example, CSP-XXXX). Please match your model number to the list provided below. You will also need to locate your order confirmation email to determine when the unit was purchased. Once you have identified the correct model number and firmware please continue by following the instructions below.

Blue Line IP Camera Troubleshooting v2

Upgrading Your Firmware

Please identify the correct model from the list of firmware provided below.

Please select the appropriate link and download the .bin file. Once the download is completed copy the .bin file to a USB Flash/Thumb Drive. We suggest formatting your USB drive to FAT32 before attempting the update.

**Note : Units with Build Dates of 2013 or earlier may require you to rename the file to “update.bin” before launching the upgrade.

Once the .bin file has been transferred onto your drive you can insert the USB Drive into either of the two USB ports found on your unit. One can be found on the front panel and one can be found on the rear of the unit.

Once the drive is inserted into the unit go to the following menu:

Main Menu –> Setting –> System –> Upgrade. Click Start. Find and select the .bin file you transferred to the USB Drive and Click Start.

*NOTE – On select models you will need to go to:

Main Menu–> Info –> Version –> Upgrade

The unit will now begin upgrading to the latest Firmware Revision that is available for your device. Once completed the system will reboot. After the reboot we recommend doing the following:

1) Remove the USB Drive from your system.

2) Change your passwords on your “admin” account. For assistance in altering your password please follow this link: https://www.cctvsecuritypros.com/content/pdfs/password-account-settings.pdf

.

IMPORTANT: If you are having difficulty identifying the correct firmware please email us at support@cctvsecuritypros.com with your order number and unit model number.

User Account Locked

Your system will lock itself out when you or someone else has attempted to log into your DVR

with an incorrect user/password combination more than three times within 30 minutes

When this happens you have two options.

1. Wait 30 minutes after the last failed login attempt and try again.

2. Reboot the DVR by using the rear toggle switch or by unplugging.

When the unit powers back on try and login with the default username and passwords.

Username: admin

Password: admin

or

Username: 888888

Password: 888888

If neither of these passwords get you into your system you will need to email us at

Support@CCTVSecurityPros.com

and request a Master Password. Once we can confirm your

account we will happily be able to provide you with the correct login credentials.

Please have your Order Number or DVR/NVR Model Number when requesting a Master

Password.

*Note: The DVR/NVR Model Number can be found on the Bottom or Side of your system.

.

IP Camera Harness Repair

If your connector looks like the ones below, moisture has gotten into your RJ45 connector. The number one cause of premature IP camera failure has to do with improper weatherproofing techniques. If caught early enough a simple cotton swab and rubbing alcohol will clean that connector right up! You may need to resort to some heavier duty electrical contact cleaner if the cotton swab method does not work.

If all else fails and the connector is too far gone and cleaning it will not work, you will need to perform a harness repair.

.

In order to perform the repair you will need:

.

.

1 x RJ45 Crimp Tool1 x Male RJ45  1 x Female to Female RJ45

Connector

.

1 x Your choice of weatherproofing ( Weatherproof junction box or weatherproof Female to Female connection)

.

.

Start by removing the RJ45 end off of your IP cameras harness. Be sure

.

Strip back the outside insulation to expose the internal cables.

.

Organize the cables to match the pinout of the IP camera. Slide the organized cables into the connector and crimp. All CCTV Security Pros IP cameras will use this pinout.

Connect your Female to Female RJ45 connector to check your work, you should have a functioning IP camera now that its void of all corrision.

Now that the IP camera has been repaired we still need to weatherproof this connection. It is now more vulnerable than ever!

Consider using a weatherproof junction box to make your connections in, or perhaps a weatherproof Female to Female connector.

Remember that different coupling styles exist so make sure that you are informed about how to use the coupler before you start crimping wires.

Troubleshooting Steps 4/8/16 Channel

(Cannot Find the Network Host)

To solve the error, please verify that the camera is properly plugged into the back of the system. If you unplug and re-plug it back in this should verify it is connected physically.

If the issue continues go to Main Menu > Camera > Camera List and delete the camera with the red status from the bottom list and do a Device Search to verify the camera is showing up on the top list.

If the camera does not show up this means the cable is not connecting properly, which could either mean the camera is not getting power or isn’t transmitting data. The best way to determine whether it is an issue with the Camera or Cable is to bench test the camera on a known working cable.

If it does show up but it has a different IP Address, please confirm the IP Address is in the 10.1.1.1-255 range (This is the default range of the internal Switch).

If the camera is not within the correct IP range, then the camera could need to be modified on the top list to properly connect in which you would select the camera, hit modify, type in the camera’s username and password and set the IP address to DHCP to automatically obtain an IP or statically assign the camera an IP address to match your switch range and gateway.

If the camera is on the correct range, you should be able to add it to the bottom list and it will come up with Green or Red, If Red double check the error message on the live view on the system.

If the Error says Invalid Username or Password, go back to Settings > Camera > Camera List and modify the camera at the bottom of the list and type in the correct login information.

If the error says Cannot Find the Network Host, check the IP Address is in the correct range, if it is you need to verify your cable is good by testing the camera with another known good cable or testing on a short patch cable as the cable could be experiencing packet loss.

Make sure the cable is T568B Standard and is within 100 meters (328 feet.)

Night Vision Issues

When a camera goes into night vision mode, the infrared LEDs around the lens turn on. If the video signal at nighttime or in dark locations is washed out, foggy or you see “halos” on the screen it is because the infrared LEDs are reflecting back into the camera lens.

cameras LEDs to focalize on the mounting surface and greatly reduce the Infrared distance.

Adding 3rd Party Cameras to Blue Line NVR

We always recommend using Blue Line IP cameras with our Blue Line NVRs for the easiest and most complete experience possible. However, we understand that using 3rd Party Cameras can be beneficial in some applications. This guide will explain the basics of adding a 3rd Party IP camera into your Blue Line NVR.

Information you will need to add 3rd Party Cameras.

With your camera attached to one of the PoE ports on your NVR, you’ll navigate to the camera settings from the main menu.

A 3rd Party Camera normally will not add itself, so you will need to go into the Camera List and click on Search Device. If the camera is detected, you will be able to select it and click on the Modify IP button toward the middle of the screen.

When modifying the IP address of the camera the default IP range for the PoE ports on the NVR is

10.1.1.xxx so you’ll want to make sure the camera is on the same range.

You will need to know the camera’s password to change the IP Address. Once the IP is successfully changed it should update after clicking Search Device again

Check the box to the left of the camera and click Add. Most cameras will show up with the Manufacturer as ONVIF. If they do not and show up as red, you will need to click on the edit button on the camera and change the Manufacturer to match the camera’s manufacturer, or to ONVIF if the manufacturer of the camera is not listed.

While in the modify window you can also enter the password for the camera in the password field. Once that is completed you can click OK. After a few seconds the status should change to a green icon and then you should be able to see the camera’s live view. Please keep in mind that if the Error Message says Invalid Username or Password you may need to login to the camera from the Web and setup an Onvif User for the system to login with.

If the camera is still showing offline, setting the manufacturer to PELCO can sometimes resolve the issue.

Additional 3rd Party Camera Information

DVR/NVR Rebooting

If your DVR or NVR is rebooting by itself please read the guide below.

If your DVR or NVR is rebooting once a week this is completely normal. Our DVR and NVR systems are designed to reboot once a week (Tuesday at 2AM by default).

If your DVR or NVR is rebooting more frequently you first want to check the power source of the DVR or NVR.

Be sure you are using the correct Power Source that was included with the DVR or NVR. Below are the correct power adapter specs so you can identify the correct one.

NVRCUBE = 12V, 2.0Amp NVRWIFI = 12V, 2.0Amp

LITE Series DVR = 12V, 2.0Amp

Pro Series DVR = 12V, 5.0Amp

Pro Series NVR = 3 Prong Power Cord to Power Outlet Extreme Series DVR/NVR = 3 Prong Power Cord to Power Outlet

If you can confirm you are using the correct Power Adapter you may need to double check the outlet you are plugged into. Try an alternate outlet and eliminate any Battery Backup Power Supplies for test purposes.

If the power source is not causing the reboot cycle it could be related to the internal hard drive. To check this out please continue reading.

First you will need to Power Off the DVR. We suggest powering the system down from the Power Switch on the rear of the system or by simply unplugging the Power Cable.

Once the system has been powered down you will need to open up the system. Please see below to locate the screws that need to be removed.

NVRCUBE or NVRWIFI

There will be 4 Phillips head screws located on the bottom of the system. Once the screws are removed the top cover will lift off.

Lite Series DVR

There are 2 Phillips head screws located in the rear and 2 on the side of the DVR, 1 on each side. Once the screws are removed the top cover will lift off.

Pro Series DVR/NVR

There will be 4 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Extreme Series DVR/NVR

There will be 2 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Once the top cover has been removed it will expose the Hard Drive and its connections.

First we want to Unplug the Large Black Connector. Press down on the metal tab and pull the connector out of the Hard Drive.

Now we want to unplug the second smaller connector (Blue Cable) from both ends. Press down on the tab and remove from the Hard Drive as well as the System Board.

Once the connections have been disconnected. Plug them back in securely and listen for the metal tab to click. This will ensure a good connection in between the System Board and Hard Drive.

Note*

While you still have the system open, it might be a good idea to check the cooling fans for any dust or debris that could be stopping the fan from moving. This could cause the DVR or NVR to overheat.

Once the connections are tight, lets put the top cover back on. When the cover is back on you can proceed to power on the system. Once the system is powered on you will need to monitor the system and check if it is still rebooting.

Disconnecting The Internet

If the system is still rebooting you may want to disconnect it from your Router or Modem by unplugging the Ethernet cable in the rear. You will loose your remote viewing capabilities temporarily while unplugged but can help us diagnose the issue.

With the cable unplugged you may want to monitor the system closely to see if this has made any changes to the rebooting issue.

Disconnecting Cameras and Other Sources

Disconnecting cameras, alarms, extra monitors and microphones is the last thing we can try to solve your rebooting issues.

Cameras, monitors, and microphones mounted near high voltage could be causing your system to reboot by itself. If your system detects any incoming voltage or amperage coming into the rear inputs the system will shut down to protect itself from damage.

Leave your main Display Monitor and Power Source connected. Disconnect one input at a time to see if it makes a change in your reboot cycle. If you notice a change in the rebooting you can single it out by using this method of elimination.

Get Started with Verkada Intercom Set up and connect your Verkada intercoms Updated over a week ago

Required. You need Org Admin and/or Site Admin permissions for your Verkada Command organization to complete these actions.

What you need

Create a site

Sites are the logical way of grouping and managing devices within your Command organization. Site-level permissions make managing and viewing your devices easier. See Manage Your Sites and Subsites for more information on site creation and management.

Add an intercom

At least one intercom needs to be added to Command before you can see the Intercom tab in the All Products menu. Intercoms can be added to Command from the Devices page. See Add an Intercom to Your Site for more information.

Connect a door

You can pair an existing access-controlled door or wire a door to the intercom that can be unlocked by an intercom receiver. See Configure a TD52 and Wire a TD52 Video Intercom for more information.

Configure receivers

Receivers allow you to answer calls from an intercom and unlock any associated doors. See Add and Configure Receivers in Intercom for more information.

Licensing

Every intercom you manage in Command will need a license. Verkada licensing is applied for each Command organization, and the licenses co-term to a single expiration date. Your licenses may have been automatically added if you claimed your devices via order number. Otherwise, manually add the licenses from the Admin page. See Manage Your Licenses for more information on adding and managing licenses.

Connect your intercom

Recommendation. While Verkada intercoms are considered low-voltage devices that do not require a certified electrician to install, we strongly recommend you work with a system integrator or other professional for installation.

Please refer to the intercom setup guide for instructions on mounting and wiring the door port.

Power and network

Verkada intercoms use Power over Ethernet (PoE) for power and communication over the LAN. In most cases, intercoms will connect directly to an 802.3af PoE standard switch. PoE injectors can be used when a PoE switch is not available. See the intercom’s datasheet for more information.

Check network settings

Verkada intercoms are designed to be plug-and-play. However, if your environment includes a firewall with custom rules and policies, you may need to make some configuration changes to get your access controllers connected to the cloud. See Intercom Network Settings for more information.

Roles and Permissions for Intercom

Roles and Permissions for Intercom

Learn more about Verkada Intercom roles and permissions

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Intercom.

Verkada intercoms setup guide v1

Verkada Intercom permissions determine who can receive calls, view intercom video, and unlock intercom doors. Intercom permissions depend on your site-level permissions, and whether you’re configured as a Receiver.

At a high level, these are the permissions granted to each level of Intercom devices:

Site-level roles

Receiver

Required. You must be configured as a receiver to receive calls.

If you’re a Verkada Intercom Receiver, you have the baseline receiver permissions (as shown above). These baseline Receiver permissions combine with site-level permissions to determine overall intercom permissions within a certain site.

For example, if you’re a Receiver for a particular intercom, and a Site Viewer, you get all the Receiver permissions, in addition to the ability to view historical video and events.

Note: Receivers, such as Desk Stations and Session Initiation Protocol (SIP) phones are not tied to a Verkada Command user. This means that the user can only get Receiver permissions, regardless of the user’s site-level permissions.

Regardless of their site-level permissions, a Receiver can:

Live-View Only

Site Viewer

Site Admin

.

Verify a user’s eligibility to receive Verkada Pass calls

.

Set Org Admin permissions

Revoke Org Admin permissions

.

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Intercom Network Settings

Intercom Network Settings

Learn about the required network settings for Verkada Intercoms

Updated over a week ago

This article outlines the required network settings that your Verkada Intercom needs to communicate with Verkada Command. For more information on the required network settings for other Verkada product lines see Required Network Settings.

Note: Verkada devices are incompatible with LANs that require proxy servers or Secure Socket Layer (SSL)/Transport Layer Security (TLS) inspection. If either is in use, a bypass for all Verkada devices must be implemented for Verkada devices to communicate with Verkada Command.

Status LED

A flashing blue status LED on the top of the intercom indicates the intercom is not communicating with Command. If you see this behavior, check that the network is set up correctly with the intercom’s requirements. If the problem persists, contact Verkada Support.

IP address

Intercoms must be assigned an IPv4 address to communicate on the LAN and to Verkada Command. Intercoms use Dynamic Host Configuration Protocol (DHCP) and User Datagram Protocol (UDP) to obtain their IP addresses and network configurations.

If you require your intercom to have a specific IP address, create a DHCP reservation using the device’s Media Access Control (MAC) address (found on the device’s label).

Domain Name System

Intercoms use the DNS server to resolve Verkada’s fully qualified domain names (FQDN) to IP addresses to communicate with them. Your DHCP server tells the intercom where the DNS server is on the network and the intercom communicates using UDP port 53.

Note: DNS over HTTPS (DoH) is currently not supported.

Power

Intercoms are powered through Power over Ethernet (PoE). This means the network switch needs to provide power to the intercom, or a PoE injector needs to be utilized. For specifics on power requirements, see the Intercom datasheet.

Firewall settings

Intercoms require access to many endpoints to ensure they can communicate with Command and all features will be accessible. Many customers may want to allow the intercoms to communicate with the general required endpoints.

These are the general domains to allow, applicable for all organization-regions:

Region: United States

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Region: Europe

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Mount a TD52

Mount a TD52

Learn how to mount the Verkada TD52 Video Intercom

Updated over a week ago

Use this article to learn how to mount a Verkada Intercom (TD52). Once you complete the mounting, you can connect the TD52 to the network.

Before you begin

You can mount the TD52 using a flush mount or using a mounting bracket. We recommend that you verify the contents of your box and make sure you have the tools you need

Contents of your box

Tools you need

Choose your mounting option

Whichever mounting option you choose, you should remove the front cover of the TD52 to access the screw holes that allow you to install on a mount.

Use a flush mount

The TD52 comes with a flush mount in the box. You can use the screw holes of the flush mount to mount the Intercom (see image below for visual):

Mount directly to a wall

Use a mounting bracket

You can use the mounting bracket to install the TD52 on to various surfaces that the flush mount plate cannot, where they’re typically used to mount the TD52 on an exterior surface.

<< Click on the page numbers to go to other pages. >>

Upgrade your DVR Security System

If you have a camera security system that is wired for coaxial and you cannot run Ethernet, you can connect our Coaxial to Ethernet Converter Kit. This enables upgrading your analog system to IP while still using existing coaxial cabling. The converters are small, lightweight, easy to install, and do not need to be connected to an additional power adapter. There is no need to run new cabling, simply plug the converters in. Send data and power over coax up to 900 m (2,952 ft) reach (performance and supported length are subject to transmission coaxial cable and coupler quality). This is a cost-effective and useful solution for legacy DVR upgrades and future expansion.

.

Coaxial to Ethernet Converters

To upgrade your wired system to an NVR with IP security cameras, you will need:

or

Features:

Easily Connect IP Cameras Over Existing Coaxial Cabling

Also Read : How to use Webcam on Surveillance Station on QNAP NAS?.

Installing your Coaxial to Ethernet Converters

Safety Precautions

Please read the following safeguards and warnings carefully before using the product in order to avoid damages or losses:

 WARNING: Do not use power line other than the one specified. Please use it properly. Otherwise, it may cause fire or electric shock.

Installation

.

Product Overview & LED Indicators

.

Mounting

The Coaxial to Ethernet Converter supports two installation modes: junction box or it can support DIN rail mount.

Note: Supports slide width of 28 mm (1.1”)

For full mounting instructions, please refer to the junction box’s Quick Start Guide on Lorex’s support page.

.

Product Specifications

.

PoE Power Supply Specifications (RG59 Coaxial Cable)

ePoE switch supply voltage 48V. / RG-59, max. DC resistance < 5 Ω / 100 m (328 ft)

ePoE switch supply voltage 53V. / RG-59, max. DC resistance < 5 Ω / 100 m (328 ft)

4K IP Wired Dome Security Camera with Smart Deterrence: Installation

This article provides instructions on how to install and connect 4K Smart Deterrence IP Dome Camera with Smart Motion Detection Plus (E893DD Series) to the NVR.

.

Before Installing

.

Installing 4K Smart Deterrence IP Dome Camera

.

Connecting 4K Smart Deterrence IP Dome Camera

Connect the cameras and cables to your NVR using one of the following two setup methods.

1. Connect cameras directly to the NVR (recommended)

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to the NVR’s PoE ports. The camera may take a minute to power on after being connected.

Note: A 12V DC power adapter (model#: ACCPWR12V1, not included) is only required if connecting the camera’s Ethernet cable to a router or switch that does not support PoE.

Notes:

2. Connect cameras to a PoE switch or router on your network (not included)

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to a router or switch on your network. See your NVR manual for details on connecting the camera to your NVR using a router or switch.

.

Using the RJ45 cable gland (optional)

The pre-attached RJ45 cable gland covers both the camera’s Ethernet connector and the RJ45 plug to provide weather-resistance and protection from dust, dirt and other environmental contaminants.

To use the RJ45 cable gland, twist the RJ45 cable gland barrel securely onto the camera’s Ethernet connector.

Tip: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for additional sealing if it will be exposed to precipitation regularly.

Cable extension options

You can extend the Ethernet cable run for your camera up to 300ft (91m). To extend the cable run beyond 300ft (91m), a switch will be required (sold separately). Use an RJ45 coupler or a network switch (not included) to connect male ends of Ethernet cables together. We recommend using UL CMR approved cables available at lorex.com.

4K IP Wired Dome Security Camera with Smart Deterrence: Getting Started

This article provides instructions on how to setup the 4K Smart Deterrence IP Dome Camera with Smart Motion Detection Plus (E893DD Series).

.

Important Installation Guidelines

The optimal installation location, including the height and angle of your camera, will depend on the type of detection settings that you want to enable. Since the optimal angle for person and vehicle detection is different from the optimal angle for face detection, you will need to select one approach.

Note: You cannot enable both face detection and person and vehicle detection at the same time.

Based on your detection preference choose between:

1. Optimizing person and vehicle detection accuracy

2. Optimizing face and mask detection accuracy

Note: Facial recording without consent is illegal in certain jurisdictions. Lorex Technology does not assume liability for any use of its product that fails to conform with local laws.

High accuracy Vs. low accuracy face detection

Accuracy will be influenced by lighting conditions and the distance/angle of a person’s face to the camera.

Mask detection

With face detection enabled, you can set the alarm type to detect if a person is not wearing a mask. A person not wearing a mask or improperly wearing a mask will be captured in the face preview sidebar and a notification will be sent through the Lorex App.

.

For full instructions on installing and connecting the 4K Smart Deterrence IP Dome Camera to the NVR, visit Installing 4K Smart Deterrence IP Dome Camera.

4K Ultra HD Smart Deterrence IP Camera: Installation Guide

This article provides instructions on how to install and connect 4K Ultra HD Smart Deterrence IP Camera (E893AB Series) to the NVR.

.

Before Installing

.

Installing 4K Ultra HD Smart Deterrence IP Camera

.

Connecting 4K Ultra HD Smart Deterrence IP Camera

Connect the cameras and cables to your NVR using one of the following two setup methods.

1. Connect cameras directly to the NVR (recommended).

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to the NVR’s PoE ports. The camera may take a minute to power on after being connected.

Note: A 12V DC power adapter (model#: ACCPWR12V1, not included) is only required if connecting the camera’s Ethernet cable to a router or switch that does not support PoE.

Notes:

2. Connect cameras to a PoE switch or router on your network (not included).

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to a router or switch on your network. See your NVR manual for details on connecting the camera to your NVR using a router or switch.

.

Using the RJ45 cable gland (optional)

The pre-attached RJ45 cable gland covers both the camera’s Ethernet connector and the RJ45 plug to provide weather-resistance and protection from dust, dirt and other environmental contaminants.

To use the RJ45 cable gland, twist the RJ45 cable gland barrel securely onto the camera’s Ethernet connector.

Tip: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for additional sealing if it will be exposed to precipitation regularly.

Cable extension options

You can extend the Ethernet cable run for your camera up to 300ft (91m). To extend the cable run beyond 300ft (91m), a switch will be required (sold separately). Use an RJ45 coupler or a network switch (not included) to connect male ends of Ethernet cables together. We recommend using UL CMR approved cables available at lorex.com.

.

Is the fan noise on my DVR NVR recorder normal?

Q- Is the fan noise on my recorder normal?

A- Digital or network Vide Recorder’s fan is comparable to one in a mini PC, and the sound coming out of the vent that you may hear is a sign of a DVR that’s working well.

The working fan indicates that the trapped heat is being dissipated, and the DVR can record 24/7 on the hard drive, and without this cooling mechanism, the DVR and hard drive’s life span will be shortened.

How to add IP Camera to Camius DVR (Advanced Security XVR)

Camius Trivault DVR recorders are designed to support analog security cameras via coaxial wiring and IP cameras over the Network. To add an IP camera to Camius DVR, you’d need to add PoE cameras to your local Network. Then, connect a regular network or PoE switch to the LAN port of the Camius DVR. Based on the example of a Camius 16-channel DVR, the connecting diagram illustrates this process. This system allows users to quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection.

If you are not using a PoE (power-over-ethernet) switch or a PoE injector, you can power the IP camera by connecting a UL-listed 12VDC-2AMP power supply to the DC plug on the camera and an ethernet cable between the IP camera and the router or switch on your local network.

Camius TRIVAULT4K2168R Connection Diagram

Camius TRIVAULT4K184R, TRIVAULT4K184R2 Connection Diagram

Navigate to the DVR’s Menu >> System >> General >> Mode >> Set to XVR and Apply.

Wait 1 to 2 minutes for the surveillance DVR to reboot in a hybrid XVR mode. This switch will reset the Configuration and Password.

There are a few ways to add IP cameras to the DVR, and we will describe them below.

Adding IP Cameras in the Start Wizard

While in the Start Wizard, navigate to the Network>> Date/Time >> IP Cameras.

Click the Search button to add compatible IP cameras on your local Network. Next, select the IP camera(s) you want to add, and then click the arrow icon to add them to the DVR, followed by the Next button.

Select the suitable Protocol from the dropdown (Private is for Camius IP cameras), enter the IP camera(s) credentials (User Name and Password), and click Add. Green status indicates a successful connection; grey status could show a password or network error.

Adding an IP camera while in the DVR’s Setup Menu

If you add IP cameras to DVR’s menu, navigate to Channel >> IP Channels.

Select the IP camera you wish to add, click the ‘Add‘ tab or use a plus button.

The ‘Add IP camera‘ window will pop up with IP camera details.

How to add IP Camera to Camius DVR (Advanced Security XVR) 21

Once the IP camera is added to the DVR, it will appear under the IP channel list. The green state means the camera has been added successfully. A grey color state means the IP camera needs attention, and when you click on the state icon, it will indicate if the error is caused by a wrong IP camera username/password or if it has a network issue.

To avoid network issues, make sure that your camera, DVR, and router are on the same IP address segment, e.g.

How to add IP Camera to Camius DVR (Advanced Security XVR) 22

Using the Camius XVR system, users can quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection. In addition, Camius Hybrid 8-Channel DVR recorders support up to 12 and 16-channel DVRs and up to 24 HD cameras, making a scalable solution for residential and commercial surveillance needs.

It is important to note that the cameras’ quality will significantly impact the system’s overall performance and effectiveness. Of course, high-quality cameras will provide better images, enabling more effective monitoring and surveillance, but also, Camius IP cameras offer intelligent motion, sound, and AI detection. Other manufacturers’ IP cameras are usually limited to basic video motion detection.

How to install a hard drive in a Camius DVR or NVR?

Installing a hard drive in a DVR (digital video recorder) or an NVR (network video recorder) (DVR NVR for short) is a relatively straightforward process. Still, it is essential to follow the steps carefully to ensure proper installation and prevent damage to the equipment. Here is a step-by-step guide on how to install a hard drive in your surveillance DVR or NVR recorder.

Camius network and hybrid digital video recorders accept 3.5″ and 2.5″ SSD internal hard drive disks. While 8 channel DVR and NVR recorders accept a single hard drive up to 10 TB in capacity, 16-channel DVR and NVR recording, along with 32-channel NVR will support a 14TB hard drive on each SATA port. 

Visit this link to see the tested and recommended hard drives, CLICK HERE

1 – Gather Tools and Equipment

You will need a Phillips head screwdriver, the hard drive you want to install, and any necessary screws (when you order a DVR or NVR from Camius without a pre-installed hard drive, the product box will include a set of screws for the hard drive disk installation).

2 – IMPORTANT: Make sure your DVR / NVR is unplugged and powered off

3 – Removing the Top Cover or the Video Recorder

Remove any screws from the Recorder’s top cover (chassis) using a Philips head screwdriver. Carefully remove the top chassis and set it aside (picture 1)

Picture 1 – 8 channel DVR

4 – Insert the Hard Drive

Place the hard drive into the hard drive bay, ensuring the drive is oriented correctly and appropriately seated.

5 – Connect the SATA Data and Power Cables

Connect the Data and Power cables to the two hard disk drives and place the hard disk drives on the video recorder’s case. The Data cable connects the hard drive to the DVR NVR’s motherboard. Locate the SATA port on the DVR’s motherboard and connect one end of the SATA cable to it. Then, connect the other end of the cable to the hard drive. The SATA Power cable provides power to the hard drive. Locate the SATA Power cable and connect one end to the hard drive and another to the Power Supply (pictures 2 and 3)

Picture 2 – Power and Data Cables on the Hard Drive

Picture 3 – Power and Data Cables on the DVR or NVR recorder’s board

Read Also : LaView NVR setup and user guide

6 – Secure the hard drive with srews

Carefully flip the video recorder case and secure the hard disk drives to the recorder with the four (4) screws if it is one SATA HDD (pictures 4 and 5) and eight (8) screws for the 2 SATA HDDs (picture 6)

Picture 4 – DVR with one internal SATA bay

Picture 5 – DVR with one internal SATA bay

Picture 6 – NVR with two internal SATA bays

7 – Return the DVR NVR top cover

Place the top cover on the DVR NVR and secure it with the screws (picture 7)

Picture 7 – DVR with one internal SATA bay

8 – Power on the DVR NVR

Power on the DVR NVR and allow it to boot up completely. If the hard drive was installed correctly and is in working condition, it should be recognized by the DVR and ready for use. Remember to format the hard drive (here is the guide on how to format the hard drive). Ensure that you use the power supply with the Camius video recorder.

IMPORTANT: Some users may find an issue when the hard drive is not recognized or not showing on the DVR. One of the primary reasons could be a wrong or defective recorder’s power supply.

That’s it! Your DVR NVR should now have a new hard drive installed, allowing it to store more video footage. Follow these steps carefully and seek additional assistance if you encounter any difficulties.

How to adjust my DVR NVR monitor resolution?

Camius video surveillance DVR NVR camera recorders have HDMI and VGA video output to live video feed on your monitor.

VGA output supports a max resolution of 1080p, while the HDMI video output 4K video resolution. So if the monitor you use with the Camius DVR or NVR recorder is capable of 4K and the camera, you can view live videos in 4K.

TRIVAULT4K2168R

How to adjust my DVR NVR monitor resolution? 19

IPVAULT1128PR

Two ways to adjust the DVR NVR monitor resolution

You can adjust the DVR NVR monitor resolution in the Wizard Setup mode or by navigating to Setup >> System >> General >> Output Configuration.

While in ‘Wizard Setup’ mode, choose an output resolution that matches your monitor. The DVR should adjust the output resolution automatically to match the best resolution of your monitor at the system startup. 

Please note that some legacy monitors could fail to communicate their acceptable resolution. In this case, please manually plug the video surveillance DVR into a newer monitor and change the resolution to the lowest setting, then save and plug the older monitor back to see if it’s supported.

After completing the Start Wizard, you can further adjust the Display Output Resolution using the following Menu Path: Setup – System – General – Output Configuration.

Select the output resolution suitable for your TV/Monitor. 1080P(1920 x 1080) will suit most monitors. If your DVR supports 4K output resolution, you can select either 2K (2560 x 1440) or 4K (3840 x 2160) to take advantage of the higher resolution that your 4K TV provides.

You can also adjust the size & position of the display screen to match your monitor/TV by using the ‘Scale and Offset’ feature; click the tab ‘Setup,’ which allows you to:

Click once or long-press the left button of your mouse on the arrow to adjust the size and position, or you can scroll the supplied USB mouse’s wheel to adjust. Click the right button of your mouse to exit, and click Apply to save your modifications.

How to reset the DVR and NVR video recorder to default factory settings

To reset DVR or NVR to default settings, navigate to the left bottom of the screen to the main menu. Select Setup >> System >> Maintenance >> Load Default

Here you can select the setting you wish to set to default. If you do not wish to reset the password, do not check the System boxes. Please note Load Default settings do not format your hard drive.

You’d need to enter the system password in the Authentication pop-up window (picture 1), which will lead to restarting your recorder (picture 2).

Picture 1

Picture 2

Navigate to Setup >> System >> Maintenance >> Reset Settings (Picture 3), where you can not select settings to reset so that it will reset your system completely, including the login credentials. You can choose ‘Format HDD‘ if you wish to format your hard drive, leading to erasing any recorded footage.

Picture 3

How to change your DVR and NVR password and add a user

You can update the ‘admin’ password by clicking the ‘User Edit’ button. You will need the admin’s current password to authenticate the new password.

Camius NVR and DVR recorder have an advanced user management feature to add multiple users to the system and control their permissions. System administration (admin) can add users, edit their permissions and delete them.

Navigate to the Main Menu in the bottom left corner, select System >> Multi-User (picture 1)

Picture 1

How to add a user to Camius NVR or DVR recorder 15

Click on the Edit icon in the User Edit column and select ‘Enable‘ in the User Enable tab. You can change the User Name or keep it as ‘user1‘. Create the new user password, confirm it, and click on the ‘Save‘ tab (pictures 2 and 3)

Picture 2

Picture 3

Then click the gear icon in the last Permission column to open the User Permission dialogue. Select (tick checkbox) the permissions you wish to grant to the new user. Click Save (picture 4)

Picture 4

How to troubleshoot if my DVR is not powering on?

If you’re having trouble with your DVR not powering on, here are some recommended troubleshooting steps:

Step 1 – Check the LEDs on the front panel, a steady green LED (PWR) means your DVR is powered on normally, and a blinking red LED (HDD) means ongoing recording on the hard drive. 

8 channel DVR

16 channel DVR

.

Step 2 – Check the sounds coming out of your recorder. A faint fan sound and a faint hard drive sound are normal, and a click sound when you plug in the DC connector and turn on the switch is typical.

Step 3 – If you have the green LED on but no output on the monitor, follow these steps:

Step 4 – Check the power outlet and the power supply unit of the DVR. If the power supply doesn’t have any LED indicator or the LED light is very faint and not bright green, and there is no fan sound coming from the DVR, the power supply may need replacement. If your DVR has running hardware warranty, please contact us. If the DVR is covered with warranty, you can order a new power supply on Camius site.

Why can’t I access my Camius IP cameras, DVR, and NVR on my Camius View app? 

If you can not access your Camius IP cameras, DVR (digital video recorder), or NVR (network video recorder) on the Camius View smartphone app, please check the below:

1 – Check if you are using the latest version of the Camius View app

On the App’s ‘Devices‘ page, make sure your recorder is added using P2P (ID) instead of IP (IP Address), and if in doubt, delete it and add it again. 

In the Media Port, make sure to enter the right port number:

2 – Make sure you’re connected to a reliable network on your phone 

3 – Check if your Camius IP camera or recorder is connected correctly to the LAN (Local network).

4 – Check for the IP address conflict

5 – Reset the Network settings of your Camius device

Navigate to Setup >> System >> Maintenance >> Load Default >> check the Network box and Apply

Camius Trivault DVR (local interface via HDMI)

Web browser view

6 – Check the Camius device network status 

Navigate to Setup >> System >> Information and check the Network Status if it shows ‘Connect success’.

If the above steps don’t help, submit a support request and include the device model number and the current ’Firmware/Software Version,’ which can be found using the Camius Device Config Tool

HDMI interface: DVR / NVR information is available under Setup >> System >> Information

Web browser view: information is available under Remote Setting >> System >> Information (web browser view)

7 – Wrong Password 

Before you add the Camius security device to the app, make sure to set a password  following the below setup guides:

We got you if you lost your IP camera or DVR NVR recorders password. Follow the below links on how to reset your device password:

You can not set a password on your Camius device using the Camius View app. 

Can I install an SSD hard drive instead of a regular one on my Camius DVR and NVR? 

The answer is ‘Yes.’

Camius recorders are compatible with 3.5″ and 2.5″ SATA (Serial Advanced Technology Attachment) and SSD hard drives (Sold-State Drive). 

Can I install an SSD hard drive instead of a regular one on my Camius DVR and NVR?  3

How to disable menu logout on the DVR and NVR?

Certain Camius device users prefer to remain logged into the menu of their DVR or NVR without re-entering their login credentials unless necessary. To achieve this, you can follow the steps outlined in this guide.

Move the mouse cursor to the bottom left, and click the main menu button: Setup >> System >> General >> Menu Timeouts >> Off >> Apply.

Optionally, you can set a different time for menu log-out as well. This guide applies to Camius NVR and DVR recorders.

It’s important to note that the web browsers will log you out of the session after some time (even if you set the number of sessions), as this function is implemented by the web browsers to enhance security.

To assist you in managing your login details more conveniently, consider using a password manager such as LastPass or similar services with browser extensions available. These services can help you securely store your login information (such as IP address, username, and password) and provide easy access even after your browser session expires.

You can also use VMS software on your desktop to add the DVR using a P2P ID and access the DVR’s ‘Remote Setting’ within the VMS; follow this guide on how to add the DVR to the software.

How to add IP cameras on a network that are not connected directly to the NVR’s PoE ports?

For the PoE-enabled NVR, connect Camius IP cameras via the internal NVR’s PoE ports and/or external LAN (WAN) port using the below-described model 2 or 3:
.

Camius PoE NVR is optimized for Camius PoE cameras making the whole setup process plug-and-play; the NVR assign a unique IP address to each Camius PoE camera and adds them automatically.

NOTE: Connecting multiple cameras via a switch or router to the PoE port is not recommended. One PoE port supports one IP camera.

The below steps are based on the NVR’s local interface via HDMI video output. Navigate the mouse to the screen’s left bottom corner and click on Setup, followed by Channel >> IP Channels.

In the below menu, you configure the connection of wired IP cameras.

Click Search to search for IP cameras from a local network, click Add to add an individual IP camera, and click Add All to add all IP cameras.

Below we will describe a few ways to add IP cameras from a local network using an external LAN (WAN) port.

IP channels menu description:

Select the suitable Protocol from the dropdown (Private is for Camius IP cameras), enter the IP camera(s) credentials (User Name and Password), and click Add. Green status indicates a successful connection; grey status could show a password or network error.

Green color State means the camera is added to the NVR

Grey color state icon means the IP camera failed to connect to the NVR. Click the gray icon to show the failure reason:

Option 1 – Adding IP Cameras to the NVR within the LAN (local area network )

If you want to connect to an IP camera from LAN (Local Area Network), please make sure your NVR is well-connected to the LAN and the IP camera you want to add is in the same network segment as your NVR.

If you want to add all channels manually, click the dropdown arrow next to Switch Mode and select “Manual.” 

If you want to add an individual channel manually, click the Edit Pencil-shaped icon in the Channel list, and then click the drop-down arrow next to Switch Mode to select “Manual” and click OK to save.

Option 2 – Adding an individual IP camera in the LAN (Local Network area)

STEP 1- Click the Search button; all available cameras in the LAN will be displayed, 

Optionally you click the Add plus-shaped green icon  in the IP channels list to add a camera to an individual channel. Click the Search button to show all available cameras in the LAN.

STEP 2 – Select the camera you want to add and then click Add button. Next, insert the user name and password of the camera and click Add button.

STEP 3 – You will see the added camera in the IP channels list

Option 3 – Add Multiple IP Cameras within the LAN

STEP 1- Click the Search button to display all available cameras in the LAN click Add All button, and the NVR will search & add all available cameras in the LAN.

STEP 2 – Select the cameras from the search result and click “Add.” You would need to input the username and password of the cameras. Please ensure all the cameras you want to add use the same username and password. Otherwise, the cameras with different user names and passwords cannot connect.

STEP 3 – The added cameras will show up in the channel list.

Option 4 – Add IP Cameras from another NVR in the same LAN (Local Area Network)

The NVR allows adding IP cameras from other Camius NVRs in the local network.

STEP 1 – Click the Search button to display all available devices in the LAN. There is an Edit icon (blue plus)  if the device is an NVR.

STEP 2 – Click the Edit icon (blue plus) and select the camera channels one by one or check the box to select all cameras. Click the icon X to go back to the Search list.

STEP 3 – Select the NVR in the search list and click the Add button.

STEP 4 – Input the Username and Password of the NVR and then click Add button

STEP 5 – The added cameras will be displayed in the channel list

Option 5 – Add IP Cameras from the Internet

If your NVR is connected to the Internet, you can add cameras with a WAN (Wide Area Network) IP address.

STEP 1 – Click Add button on the search page.

STEP 2 – Input the IP address or Domain name, Alias (name of the IP camera), Port, Protocol (choose the protocol of the IP camera from the dropdown menu: Private, Onvif or RTSP), User Name & Password of the IP camera.Tap the Add button to add the camera.

To avoid network issues, make sure that your camera, NVR, and router are on the same IP address segment, e.g.

.

How to configure Camius NVR using a web browser?

To quickly find the Camius DVR (digital video recorder) or NVR (network video recorder) IP address, visit camius.com/support to download and install the Camius Device Config Tool.

Web browser access

Click on the Camius NVR or DVR’s local IP or type it into your browser’s address bar. The latest Camius surveillance security camera recorders work with multiple web browsers, including Edge, Google Chrome, Mozilla Firefox, Edge, and Safari, and include the following models:

Use your admin username and DVR or NVR password to log in. Your recorder’s Configuration is under Remote Settings.

You can check the ‘Web Compatibility Mode‘ in the Camius NVR/DVR and even IP camera settings (this can be done from the Camius recorder’s local user interface (Via HDMI/VGA) and in the web browser viewer.

The below picture is based on the IPVAULT1128PR’s web browser view

Accessing web client through VMS software

For certain Camius DVRs, NVRs, and IP camera models, we recommend installing the VMS Software on your Windows or Mac computer to access the device’s remote settings since the VMS software has a built-in web client using the P2P ID. Here is the link to the guide on how to add the device to the VMS software. This applies to Camius IPVAULT2320P16N, SCOUT20PTZ, GUARDMA

.

.

Can I add cameras over the network?

Yes, you can add cameras over the network, they do not have to always be connected directly to the NVR. You can use a switch on the network that connected to the same router as your NVR. Please follow these steps to set this up:

Log into the NVR and go to Camera>Camera Management, click on Manual Add, and enter the IP information for the camera. Use the default username: admin password: 123456

Can I connect all the cameras to a switch, then the switch to one of the NVR ports?

No, unfortunately each port on the back of the NVR is only designed for 1 camera. This will only allow about 2 cameras to show up. To use a switch, you’ll have to connect the switch to the same router that the NVR is connected to. Then you’ll proceed to setup the cameras over the network. Please see the Adding cameras over the network FAQ.

Can I use my PC to view my cameras remotely?

Yes, you can use your external IP address to view your cameras and manipulate configuration via Web Browser. Our plug in will only work on Internet Explorer or Mozilla Firefox. Once one of those browsers are open, type in your external IP address in the URL bar. If the port forwarding is done correctly, it should bring you to your NVR log in page. Log in using the same credentials as you would directly on the system. After you’re logged in, click the link to download and install the plug in. Restart the browser and click the “All Main” button on the left-hand side, and it should bring up your camera streams.

LaView NVR setup and user guide

Read Also : LaView DVR User Guide

Can I use port forwarding to setup remote viewing for my NVR?

Yes, you can setup your system via port forwarding. Although, this setup is recommended for more advanced users. You will need to note the IP Address of the NVR/DVR. To obtain this, go to Main Menu>Maintenance>System Info>Network, your IP address will be the IPv4 address at the top. Then you’ll need to log into your router via web browser on a PC. Once logged in, you’ll need to add ports 80, 8000, and 554 to the port forwarding rules. For help with port forwarding for your router, contact the manufacturer or your ISP. There are also guides for a lot of various models of routers here https://portforward.com.

The port forwarding setup should look something like this:

Application   Start     End         Protocol   IP Address

DVR1                 80           80         TCP            192.168.x.x.

DVR2               8000      8000       TCP            192.168.x.x.

DVR3                554         554       TCP            192.168.x.x.

To make sure test the ports on www.canyouseeme.org, and if they are open you can add the information to your phone app.

LaView Net App Setup:

*Make sure Wi-Fi is off on the phone when attempting the remote view.

How do I change the camera names on my system?

To change the camera names go to Menu>Camera Management>Advanced>Basic>IP Camera Name. In that section, you can edit the “Camera Name” Option, please click apply at the bottom before selecting another camera.

How Do I Set up Remote Viewing for My Surveillance System?

Assuming you have the IP address of the NVR/DVR, there is a 4-step process to set up remote viewing. Learn more about remote view camera set-up here.

Are There Any Cameras that Also Allow Me to Monitor the Audio as Well as the Video?

Yes, we have multiple solutions available to our clients. Here is our most popular audio camera.

Does the Surveillance System Come with All of the Wires, Switches, and Accessories I Need?

Yes. The kit comes with everything you need to install the system and begin recording immediately, including  any necessary wire, PoE switch, or AC 12v adapter required for the system to operate.

How far Apart Can I Set up My Wireless Cameras?

The environment, particularly barriers such as cement walls, steel structures, or large trees, play a big role in transmission distance. A wifi camera will typically transmit well for about 150 feet outdoors and 50 feet indoors.

How do I connect my NVR to my Phone?

Please download and use LaView Patrol:

Note: The app set up is done on an Android device, the iPhone set up will be almost identical.

2. Click on the “BACK” button. Tap the “+ Device” option to add a device.

3. Enter IP address information and click “Save”. Your new device will be on the previous screen. To obtain his IP address go to Main Menu>Configuration>Network. Your IP address will be the “IP address”. (Please note: This setup will only work inside the local network. To enable remote viewing, setup port forwarding and use your WAN IP address from your network. See port forwarding instructions.)

4. Select new device and choose the channels you wish to see, click the Play/Live button.

How Do I find my system’s IP address?

To find your system’s IP address go to Main Menu>Configuration>Network. The IP Address at the top is your local IP. If your IP address is 0.0.0.0 or 192.0.0.64, this means your system is offline. There are a few causes from this, but usually it’s a bad ethernet cable or the cable is not plugged in properly to either the NVR or Router. If those are checked to be correct, try restarting your router by unplugging it for a minute and restarting the DVR.

Do I Need Internet to Activate My Wireless Security Camera System?

Not exactly. You can set up your wireless security camera system without any internet at all, as this is not a requirement to begin recording. In order to access remote viewing on your mobile devices, you will need a live internet connection.

Does the Surveillance System Come with All of the Wires, Switches, and Accessories I Need?

Yes. The kit comes with everything you need to install the system and begin recording immediately, including  any necessary wire, PoE switch, or AC 12v adapter required for the system to operate.

Are There Any Cameras that Also Allow Me to Monitor the Audio as Well as the Video?

Yes, we have multiple solutions available to our clients. Here is our most popular audio camera.

What are the Advantages of Installing a Wifi Security Camera System?

A wifi security camera system is significantly easier to install than a traditional system, because there is no need to run special wires to each wifi camera. This not only helps the day of installation, but also allows clients to position cameras in places they might not otherwise be able to place them.

How Do I format my HDD?

To format your HDD you’ll need to go to the Main Menu>System>Storage>Management Tab. Once in the HDD menu, highlight the HDD information. Then click on “Format” at the bottom. Please note this will delete all information off the HDD.

How do I playback my recordings?

To playback videos go to Main Menu>Playback. In that section choose your camera(s) on the right-hand side. Then double click any of the days on the calendar. This should automatically start playback for that day. Use the bar at the bottom to jump to a specific time during that day.

How Do I set up my recording schedule?

To set the recording schedule you’ll need to go to Main Menu>Configuration>Schedule>Record Plan. In that section, you’ll have access to each channel’s recording schedule. The camera’s will automatically start and stop, recording, at desired times. If you want to set up only motion recording to each camera, select “Setting” on the right-hand side for the desired day. Choose MD for Motion Detection for the day and set a desired time, if not all day. Then you can copy the schedule to other days at the bottom. Click apply then ok, then apply again. You can now click copy at the bottom and copy the schedule to other channels as well. Or choose another channel at the top to setup a different schedule.

How Do I upgrade my system’s Firmware?

Make sure to download your firmware from our website here: https://www.laviewsecurity.com/cms/download/

Once the file is downloaded, extract the file and place it onto a flash drive. Then connect the flash drive to a USB port on the NVR.
Please go to Main Menu>System>Maintenance>Version and select upgrade. Choose your Firmware file from the list.

How to I download videos off my NVR?

To download video footage you’ll need a flash drive inserted into one of the USB ports on the system. Then go to Main Menu>Backup. Once in the Backup page, you’ll need to select the USB device from the list. Then click on “Backup” at the bottom and you’ll have the file selector screen show up. Make sure AVI is checked, then proceed to backup. You can select a specific channel along with date and time you want to backup. Click on Add, then the list should update. Each file will have a start and end time. Check mark the files desired for back up and click backup at the bottom. Once the progress bar finishes, you now have the files on your USB drive.

I forgot the password for my system, how do I reset it?

Please email us at info@laviewusa.com to reset the password for this system. In the email please mention you need a password reset along with the model number and date that displays on the main view of the system. A technician will reply with some instructions and a temporary password for your system.

I have port forwarding setup, but my external IP address keeps changing. Can I fix this?

Yes, you can either contact your ISP and ask them for a static IP address or setup a DDNS. LaView does offer a free DDNS service that you can setup with these instructions:

To set up a DDNS please go to www.laviewddns.com and register.

After registering and creating your domain name we need to enable the DDNS feature.

Please go to Main Menu>App Center>DDNS.

Enable DDNS: √ (Checked)

DDNS Type: Laview

Domain Name: “yourdomainname”.laviewddns.com (“yourdomainname” is the name you created don’t use that or the “ “)

User Name: your email account used for www.laviewddns.com

Password: password used for www.laviewddns.com

Server IP: Laviewddns.com

Port: 8000

Please note, in order for the DDNS to work, port forwarding must be setup. You can now use your Domain name to access your system instead of IP.

I have some trees in my yard that are triggering my motion detection. How can I fix this?

You can setup areas for your motion recording within the camera’s configuration. Go to Main Menu>Configuration>Alarm>Set Area “Setting”. In that section, you’ll have a preview of one of the camera along with a red grid over it. You can clear the area and only draw specific areas with motion detection. Or you can just remove the areas by clicking and dragging over the red boxes. Everything in red will trigger motion, anything clear will not.

Which mobile app do I need?

-If you have DVR starting from LV-N52xxxx please download “LaView Patrol”

-If you have DVR starting from LV-N9xxxx, LV-D11xxxx, LV-D21xxx, or LV-T94xxxx, please download “LaView Net”

-If you have DVR starting from LV-D04xxxx, or LV-D51xxxx  please download “LaView Mobile”

The system worked seamlessly until last week when it suddenly shut off and now won’t come back on

Would suggestion you follow the instruction below for troubleshooting,

1.Please ensure the cameras are connected, would suggest you to connect them directly to the PoE ports at the back of the system.

2.At the day time, try to cover the camera lens with your hands to see if there is a IR red light on the problematic cameras. And please also check if the camera goes hot when it is connected.

3.The camera appears not to get powe if there is no light and heat. We will need to check if it is the camera/port/cable issue.

1.At first, please switch the problematic camera to the workable PoE ports to test. You can also go to your PoE Configuration setting to check the power.

2.If it still doesn’t work with another port, please exchange the cable to check again. If possible, you can also add the camera to another system to confirm the problem.

Please contact our support team for further support if it does not help.

What should I do if I connect a LaView Saturn Camera to LV-N96, LV-N95, LV-N98 series NVR but only get 720P maximum resolution in main stream?

If you only get 720p in mainstream, it means the IP camera is set to H.265. Please use the following instruction to switch the camera to H.264 compression.

What features are LaView Saturn Series Camera compatible with LaView (LV-N95, LV-N96, LV-N98, LV-N99) Series NVR?

LaView Saturn Series IP Cameras have many great features designed to work with LaView Saturn Series NVR. If you already have a LaView NVR and wish to add a LaView Saturn IP Camera, you can do so using this instruction. However, we recommend using LaView Saturn Series IP Cameras with a LaView Saturn Series NVR for best performance.

The following features of LaView Saturn IP Camera are compatible with LaView Series NVR:

The following features may NOT be compatible

How to reset LaView Saturn IP Camera

3. Press and hold the reset button for at least 5 seconds until the camera restarts, and then the camera will be restored to factory default settings.

How to connect a LaView Saturn Series IP Camera to a Non-Saturn Series NVR

5a. If you are connecting the camera to the NVR PoE port, set up the Target IP to 192.168.254.xxx (xxx being a random number from 2-254), and Gateway to  192.168.254.1, Subnet Mask 255.255.255.0. Then unplug the camera from the PoE switch or Router and connect it to the NVR using Cat5e cable.

5b. If you are connecting the camera via LAN, use DHCP or set up the IP address to your network range. For example: Target IP 192.168.0.217, Subnet 255.255.255.0, Gateway 192.168.0.1

6. Go the NVR Menu => Camera => Camera.

7. Click on the channel which the camera is connected to (ie if the camera is connected to port 3 on the back of the NVR, click on channel 3). If you are connecting the camera via LAN, Click on any unused channel.

8. Change ‘Plug and Play’ to ‘Manual’ and enter the camera IP address (192.168.254.xxx or 192.168.0.217 as in previous example)

9. Change protocol to ONVIF and Management port is 80

10. Enter user name and password you set up when you activated the camera in step 3.

.

.

Welcome to our updated comprehensive how-to guide for getting started with your Hikvision IP CCTV system. IP systems are taking over the surveillance world and whether you’re setting up your brand new Hikvision system, or you need help adding more cameras to an existing setup you have, the step-by-step guides in this Megaforum should be all you need to get up and running!

Part 1: How do I install a Hard Drive in a Hikvision NVR?

Any setup with an NVR will need a hard drive to function as it is what all your footage is saved to. The WD Purple Drive is our go-to recommendation for the vast majority of IP setups as it designed with the high workload requirements of 24/7 surveillance solutions in mind. Please see the guide on picking the right HDD to better understand your storage needs and why we don’t recommend using HDD’s that aren’t optimised for use in a CCTV system.

Please see the five simple steps below for getting your hard drive installed into your NVR:
.

.

Step 1:
.

Firstly, you’ll need to locate and remove the screws that secure the NVR’s casing to the base so that you can access the inside of it. Typically, you’ll find two of these screws on the back of the unit and, depending on the NVR model, more on the sides – Do not lose these screws!​

.

.

Step 2:
.

Once inside, your NVR will look something like this. The parts in here you’ll need to identify are the:​

.

.

Now look at your HDD – fewer things to identify here:​

Step 3:
.

Get your hard drive and NVR connected – You can screw the drive into its bay in NVR first if you wish, but it’s normally easier to wire everything up first. Plug one end of the SATA interface cable into the HDD and the other into the corresponding port on the motherboard, then do the same with the SATA power cable. If the power cable has come already connected to the motherboard, then just plug the other end into the HDD’s SATA power port.​

.

.

Step 4:
.

You now just need to screw the HDD into the bottom of the NVR via the screw holes located in the HDD and corresponding holes in the HDD bay (insert the screws from underneath the NVR into the HDD inside – it can be a bit fiddly).​

.

Step 5:
.

Finally, screw the NVR’s casing back onto the base. Your HDD is now installed and ready to be formatted during the initial NVR setup, which is explained in Part 2.​

Part 2: How do I complete the basic setup of my Hikvision NVR?

You now need to configure the NVR so that it’s ready to connect to your network. Don’t worry – this is simpler than it sounds. This initial setup is simplest when done on the local GUI, using a directly connected monitor. The following steps walk you through this initial setup process:

Note – Avoid plugging anything into the back of the NVR until instructed to do so in this tutorial.

Firstly, you’ll need to look at the back of your NVR and make sure you can identify the following parts that are needed for this stage:
.

[1] – PoE (Power over Ethernet) ports (Most Hikvision NVRs have PoE ports which will power any camera via the network cable. Those that do not will require you to connect the camera across remotely, using a separate PoE injector or switch for power.)
​

[2] – VGA display port
​

[3] – HDMI display port
​

[4] – USB port(s) (and mouse – one should come included with the NVR)
​

[5] – LAN port (and ethernet cable – Cat5e or Cat6 is fine)
​

[6] – Kettle power socket (the power lead is included with the NVR)​

Now, follow these steps. It is easier if you leave your cameras disconnected until prompted later in this guide:

Step 1:
.

Plug the kettle plug into the power inlet to connect the NVR to a power supply.​

​

​

.

​

Step 2:
.

Connect your NVR to a display (this can be any monitor or television) by connecting either an HDMI or VGA cable from the monitor to the corresponding port in the back of the NVR.​

​

.

​

Step 3:
.

Plug your USB mouse into one of the NVR’s USB ports.​

​

​

Step 4:
.

Use an ethernet cable to connect your NVR to your local network – Plug one end of the cable into the RJ45 ports into a network access point (such as an ethernet port on your router), and the other into the LAN port in the back of your NVR.​

​

​

.

​

Step 5:
.

Turn the NVR on and let it boot up. Ignore the beeping noise, it’s completely normal and just the NVR telling you that it isn’t properly configured yet.​

​

You may get a prompt to adjust the NVR’s resolution to match the connected display, click “yes” to view everything in the best resolution supported by your display.​

​

​

​

Step 6:

​

Set your language when prompted.​

​

​

​

Step 7:
.

Set a password for the NVR , as well as a “Channel Default Password”, which will be passed onto any inactive device that is directly connected to the NVR’s PoE ports. We recommend keeping these passwords the same for simplicity’s sake. It’s key that you set a password that the NVR defines as strong and that you remember this password, as resetting the passwords on Hikvision devices can be a hassle that you want to avoid, if possible.​

​

Note – If you have lost your password then please see our guide on How to Reset the Password of your Hikvision Camera/NVR in 5 steps using the SADP Tool​

​

​

​

Step 8:
.

Now set a valid “reserved email” address for the NVR, which Hikvision will use for verification if you need to reset your password.​

​

Step 9:
.

Next, set an unlock pattern of your choice by using your mouse to draw any shape you like – you will be asked to do this twice to confirm the pattern. This will be used to quickly login to your NVR in the local GUI.​

​

​

Step 10:
.

Now, set your time zone, your preferred date format, and date/time.​

​

​

Step 11:

​

On the Network Setup page:​

​

Leave the “NIC Type” as it is.​

​

Either leave the “Enable Obtain DNS Server” box ticked, or untick it and use one these recommended public DNS servers.​

​

It is best to leave the “Enable DHCP” box unticked here. Instead, set the “IPv4 Address” of the NVR to an unused IP address on your network, which is within your gateway’s range. Your Gateway will typically be the IP address of your router. E.g. if your router’s IP address is “192.168.1.1”, you’ll want to give the NVR an IP address within the range of “192.168.1.x”, where “x” is any unused address between “2” and “254”.​

​

Note – DHCP can be left on during this stage of the setup to automatically assign your NVR an open IP address if you like, just be sure to turn it off again once your system up and running. To disable it again once set up, just go to: ​

System/Configuration→ Network → TCP/IP → DHCP Off → Apply​

​

Input the Subnet Mask of your network (typically it’s “255.255.255.0”) and “IPv4 Default Gateway”. If you’re unsure of these, see the below articles which explain how to check what they are and if a particular IP address is available:​

How to setup Hikvision IP CCTV System

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

The “Internal NIC IPv4 Address” can be left as it is, this just refers to the NVR’s own LAN address (so Plug and Play cameras will use IP addresses on this range).​

​

​

​

Step 12:
.

You can now stop the annoying bleeping! Select your hard drive(s) from the list and click “Init” to format it, and then “Next” when the formatting has completed.​

​

Note – This will completely wipe the drive, so please make sure that any that are being reused to not have data that you might need on them. ​

​

Step 13:

​

The next page is for the Camera Setup. As mentioned earlier, we recommend connecting any cameras after the NVR setup process has completed, so you can skip this page.​

​

Note – Please see part 4 for the instructions for adding cameras to your NVR after the initial setup. ​

​

Step 14:
.

You will now be taken to the platform access page. Again, skip through and leave this for now.​

.

Note – Please see part 12 for adding the NVR to the Hik-Connect app, which revisits this page. ​

​

​

Step 15:
.

Finally, you’ll be taken to the Change Password page and given the option to set a new admin password. Ignore this, unless you actually want to change your password. Remember, your admin password is different from your activation password, which you’ll need to use when activating individual cameras on your network.​

​

Click “Exit” and “Yes” on the “Exit Wizard” popup.​

​

​

.

That’s the initial setup of your NVR complete. You should now be taken to the NVR’s live view page (you won’t see your cameras until these are connected in Part 4), with your main navigation menu at the top of the screen.​

​

.

Part 3: How do I find my Hikvision device and edit its network settings?

You probably want to be able to view your camera feeds remotely wherever you are; either in a web browser, the iVMS-4200 software, or the Hik-Connect mobile app. All IP CCTV devices communicate over your LAN (local network) and have a unique location on the network. So, you will need to be able to locate where the device you want to view is and make sure it has the right settings for it to work on your LAN. You will then be able to access the device from a PC or mobile device, and connect it with the rest of your CCTV system.

Please follow the steps beneath to find and correctly set your Hikvision device’s network settings.
.

.

Step 1:
.

The first step is to work out if you need Hikvision’s SADP tool or not. If you only need to discover and access an NVR and some Plug and Play cameras connected directly to its PoE ports, then you don’t need to use it.​

​

​

If you aren’t using the SADP tool:​

​

Or, on the NVR’s local GUI (Graphical User Interface – when operating the recorder from a connected monitor and mouse), go to:​

​

System → Network → TCP/IP​

​

Here, you can view and change the NVR’s network settings to match your LAN which is explained in step 2 – you can then ignore the rest of the steps.​

​

​

If you are using SADP:​

​

If your cameras are connected to your LAN, rather than to an NVR’s PoE ports, you will need to install the SADP tool. This scans for all Hikvision devices on your LAN by their MAC addresses. Now, follow steps 2-5 below.​

Step 2:

​

You now need to identify some of your LAN’s settings, which you need to set to match on your devices.​

​

From a Window’s PC, you will need to use the Command Prompt tool to find these.​

​

If you’re using a Mac, then you can find these by launching System Preferences, and then going to:​

​

Network → Advanced (make sure your Wi-Fi/Ethernet connection is selected on the LHS) → TCP/IP​

​

​

Make a note of the following numbers, as you will need to use them when changing your device’s network settings:​

​

IPv4 Address – This is the IP address of the computer that you are using. This address is therefore already occupied, so you will not be able to assign any other devices to this specific address. The digits after the final decimal point indicate where the device is located within the range of your local network, which spans 1-254. You’ll need to change the number after the third period (or full stop/dot) to something that is between “1” and “254” and not already occupied by another device on the LAN.​

​

NB – Please see these guides for instructions on checking if a proposed IP address is occupied:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

Subnet Mask – This shouldn’t need to be changed on the NVR, it will usually be “255.255.255.0”.​

​

Default Gateway – This is the IP address that’s been assigned to your router. Any device being added to your system needs to be within the range of your gateway in order to be discoverable.​

.

Step 3:

​

Now, launch the SADP tool again. It should show a list of all the Hikvision devices on your local network and their default network settings. Provided the device is being powered and has a connection to your LAN, then it will show up here. You can also alter the device’s network settings here, and check things like the model number, serial number, the firmware version installed on it.​

​

NB – Remember that any camera that is directly connected to your NVR’s PoE ports will not show up in SADP. This is because the NVR hides any cameras directly connected to it from SADP on its own “subnet”, which is separate from your local network. Don’t worry though, as you won’t need to change the settings for these cameras. ​

.

Step 4:

​

Tick the box beside your device to view and edit the network settings.​

​

If the device hasn’t yet been connected to the network then it will show as “Inactive”. You will be asked to set a password for it when you click the tick-box for it. For more instructions on activating your device, please see Part 6.​

​

​

.

.

​

Once activated, ticking the box beside your device will change the network settings in the “Modify Network Parameters” window, so that they match your LAN. You need to make sure that you enter the password for that device before clicking “Modify” for these changes to be saved.​

​

.

Step 5:
.

Check that these changes have been reflected in the SADP device table – you may need to wait a few minutes before refreshing. If they have, then you should be to carry on with getting this device connected to the rest of your system.​

​

NB – If you aren’t the camera’s first owner then you will need to perform a hard reset on it. This will reset the device to its inactive factory state so that you can set new password by activating the camera in SADP. Once this has been done, SADP will allow you to modify each network setting edit the network settings to match your LAN so that you can use the device standalone or add it to your NVR remotely.

.

Part 4: How do I add a Hikvision device to my NVR?

There are a couple of methods for getting your IP camera connected and recording to your NVR:
.

Plug and Play – This is the most popular and simplest method for smaller setups, as all you need to do is plug your camera straight into the PoE ports in a Hikvision NVR. The NVR will then do the rest of the work. Please note that for Plug and Play to work, the device will need to be inactive or activated with the same password as the NVR.​

​

Remote connection via IP – If you can’t have a wired connection to the NVR, you can instead remotely add a camera on the same network as your NVR to it using the camera’s IP address. For this to work, you will need to make sure to do two things:​

​

1. Replace the power supply that would normally come from the NVR’S PoE ports. Using a PoE switch or injector is usually the best way, as it means you can still add power to the device over the same ethernet cable used for everything else. If not, most will let you connect to a separate PSU.​

​

2. You have connected the camera and NVR to the same LAN and that its network settings are correct for the LAN’s range.​

The following steps will guide you through adding new devices using both of these methods. Part 1 covers doing this on the NVR’s local interface (GUI) and part 2 covers how to do this remotely using a web browser.
.

.

Method 1 – Via the NVR’s GUI:

.

Step 1:​

On the NVR 4.0 menu at the top of the screen, go to:​

​

Camera → Hover over the desired channel → Click on ‘Edit’ (small icon in the bottom-left corner of channel thumbnail)​

​

​

.

Step 2:​

An edit window should appear, fill out the fields to add your camera as follows:​

.

Option 1 – Using “Plug and Play”​

​

Connect the camera to the corresponding PoE port number on the NVR (I.e. D1 corresponds to port 1). Then, just select “Plug-and-Play” from the “Adding Method” dropdown, and then click OK to add the camera to that channel – the camera feed should appear after a few seconds to confirm that it’s been picked up.​

​

Note – If you haven’t activated and set a password on the device in SADP, then the IP address should automatically work. The password will be the Activation Password set on your NVR in the initial setup.​

.

.

Option 2 – Adding manually via IP​

​

Change the “Adding Method” to “Manual”, which will let you alter the other fields.​

​

Now edit the other fields to point your NVR to the camera’s location on the network, like below:​

​

​

Adding Method – Select “Manual”.​

​

IP Camera Address – Enter your camera’s IP address here (as explained in the introduction, this will need to match the range of your LAN).​

​

Protocol – Select the device’s manufacturer if it is on the list, or “ONVIF” if it is an ONVIF conformant product.​

​

Management Port – “8000” by default will work fine, or whatever you’ve set the device’s Server Port to if it’s been changed.​

​

Channel Port – This refers to the channel that you want to add the camera to, so leave this as the corresponding number for the channel that you would like to edit.​

​

Transfer Protocol – Set this to “Auto”.​

​

Username – The username you set up when activating the device, usually “admin”.​

​

Password – The camera’s password, which you will have set when it was first activated.​

​

Use Channel Default Password – If you have assigned the NVR and camera the same password during their activation, then you tick this box. This will use the NVR’s password to add the camera and will save you from entering it again in the future.​

​

Enable IP Camera Time Sync – Tick this, as it means the camera will synchronise with the time set on the NVR.​

​

Use Default Port – You can leave this unticked, as you have specified the management port already.​

​

Verify Certificate – Leave this box unticked too.​

​

​

Click OK to save your changes, the NVR should pick the camera up after a few seconds and show the feed on that channel’s thumbnail to confirm this.​

.

.

Step 3:​

To rename the camera, go to:​

​

Camera → Display​

.

Then, select the camera’s channel from the dropdown, and use the field below to set a new name.​

​

Click “Apply” to save your changes.​

​

​

​

​

Step 4:​

You may want to rearrange the Live View screen to show the new camera on a particular tile. To do this, first, go to:​

​

System → Live View → View​

​

Then, select the output port for your connected display that you would like to show the camera on, click on the selected tile and then double-click on the new camera to add it to that tile.​

​

You can select different layout options, or create a customised layout using the toolbar at the bottom of the page.​

​

Click “Apply” to save the new layout.​

​

​

To check the new layout, launch “Live View” using the NVR’s main menu, and then select that layout using the toolbar in the bottom right-hand corner.​

​

​

.

Method 2 – In a web browser:

.

Step 1: ​

Browse for NVR’s IP address in a web browser, and log in with your username and password for it.​

​

.

Step 2:​

Now, navigate to:​

​

Configuration → System → Camera Management → IP Camera​

​

You’ll be shown a table of all the NVR’s channels, showing which are occupied by cameras, and which aren’t.​

​

These channels normally correspond to the same-numbered PoE ports on the back of the NVR.​

​

Click on the channel that you want to add your device to, and then the “modify” button above the table.​

​

.

Step 3:​

A window titled “IP Camera” should appear allowing you to change the “Adding Method” and “IP Camera Address” set for that channel.

If you haven’t already, you will need to make sure that the camera has a valid IP address and correct network settings for your LAN’s range.
.

Option 1 – using “Plug and Play”:
.

You just need to make sure that:​

​

Note – If you haven’t activated and set a password on the device in SADP prior to connecting it to the NVR, then the IP address should automatically work and the password will be the “Channel Default Password” set on your NVR in the initial setup (see step 7 here)​

.

Option 2 – Adding manually via IP:​

​

Change the Adding Method to Manual, which should let you alter the other fields.​

​

Now alter the other fields to point your NVR to the camera’s location on the LAN, like below:​

​

​

IP Camera Address – Insert the camera’s IP address​

​

Protocol – Select the brand of your camera here, or ONVIF if it is ONVIF conformant and the manufacturer doesn’t appear in this list.​

​

Management Port – This is the camera’s network port, which is usually 8000 by default.​

​

Username – The username that you set for the camera, which is usually “admin”.​

​

Password – The password assigned to the camera upon activation in SADP. If you have automatically activated the camera by plugging it into your NVR’s PoE ports, this will the the “Channel Default Password” set during the NVR setup.​

.

Confirm: Retype this password.​

​

Transfer Protocol: This is fine for you to leave as “Auto”.​

​

.

Green ticks should appear beside each field to indicate that what’s inside is valid. Once completed, you can click “OK”:​

.

​

The “Security” column should be “Strong” and “Status” should change to “Online” on the “IP Camera” page – If they do, then you’re finished, just return to the Live View page to check that the camera’s feed is now visible.

​

Note – Clicking the “Start All Live View” button in the toolbar at the bottom of this page will show all of your working cameras feeds at the same time.​

​

Click on other pages for more.

How to Add a Uniview NVR Device to EZstation for Viewing on the Local Network (LAN) Only

This guide will show you the few simple steps to add a Uniview product (NVR/IP Camera) to the EZStation software for Local Viewing only.   This can prove beneficial in cases where:

1. There is no internet access.

2. Viewing the device remotely isn’t needed.

3. Signing into a cloud account on EZStation on the same network as the device is slow to load the video.

Note:

-EZStation should already be installed and running.

-Click on any of the images below to enlarge them in a new tab.

1. Click Device Management

Read Next :

1. Uniview IP Security Camera Guides
2. Uniview NVR Remote Access
3. Uniview Setup Guide: Video Content Analysis

2. On the Device Management page the top section on the right labeled “Managed Device” will show devices that have been added to EZstation.  The bottom section on the right labeled “Online Device” will show all devices that are detected on your local network.

1. Select the device from the list on the bottom.

2. Click the Add button.

3. The device will now be added to the top Managed Device section.  If the default password to the device was changed previously it’s important to click the Edit button and input the password on the window that comes up, then click Okay.

4. If everything went well the Status should now say Online.

5. Click the Live View tab at the top of EZstation.  Lastly, double click on the device on the left column to start the live view.

How to record audio on a Uniview NVR

Record audio on a Uniview NVR by following each step below

NOTE

-This audio setting has only been added on select models with newer (2022+) firmware installed. -This guide assumes you have already enabled audio on the IP cameras with a microphone.

1.  After logging into the web interface of the NVR go to Setup->Camera->Schedule.

2. Select the camera you want to enable audio recording on by clicking the drop down.

4. Change the Audio Storage option to On.

3. Click Save.

Creating New Users

Adding users to your UNV NVR allows you to customize exactly what people are able to see when operating your device, which can help protect your settings and the security of your device.

This tutorial assumes you have already completed the basic set up for your UNV NVR

Accessing and Configuring a New User

1. Sign into your UNV NVR. To do this, start at the Live View screen of your NVR.
2. Right Click Anywhere on Live View > Main Menu > Draw Pattern or Enter Password
3. You will be taken to the main menu. Click on “System” and then navigate to the “User” menu. At the bottom of the screen, you will see a button labeled “Add”. Click there.

You will see a pop up menu with everything you need to configure your new user. From top to bottom:

1. Username: This is the username for the user you are creating. It can be whatever you’d like.
2. User Type: This controls the general configuration for the user you are creating. You will notice that you cannot have more than one admin account.
   1. Operator: This is a user type that has permission to use the NVR configuration menu. Use this account type if you want your user to be able to change and configure your NVR through it’s main menu. Please Note: You can customize exactly what permissions this user gets, but by default, the Operator type is used for tech support and configuration.
   2. Guest: This is a user type that has permission to ONLY view Live View and Playback on your NVR. You can customize exactly what cameras they can view. This is the recommended user for anyone that is only allowed to Live View and Playback your cameras.
3. Password: This is the password that the new user will use to sign into the NVR. It must be considered a “STRONG” password. Once you have decided upon a strong password, you must retype it in the Confirm Password section.
4. Pattern: As with the admin account, your user account can have it’s own distinct lock pattern. This is where you can draw that pattern. Please note that the pattern MUST be distinct from other users, or there will be a conflict.
5. Permissions: This menu allows you to configure permissions for your new user account.
   • 1. Basic Permissions:
        1. Configure: This allows the use of the main menu to configure the settings of the NVR. Only give this option to trusted users.
        2. Upgrade: This allows the user to update the firmware on the cameras and recorder. Only give this option to trusted users.
        3. View and Export…: This allows the user to view and export logs and configuration files. Only give this option to trusted users.
        4. Restart: This allows the user to restart the NVR. Only give this option to trusted users.
     2. Camera Permissions:
        1. Live View: This allows the user to view the Live View on certain cameras. You can choose either all cameras or specific cameras by selection the camera numbers on the right-hand side. Unselecting a camera will turn that camera into a blank square when this user is logged in.
        2. PTZ Control: This allows the user to move and zoom cameras that have the ability to do so. Only give this option to trusted users, as they will be able to adjust the position on motorized cameras.
        3. Playback: This allows the user to view Playback on certain cameras. ou can choose either all cameras or specific cameras by selection the camera numbers on the right-hand side. Unselecting a camera will force the error “You Do Not Have Permission” if the user tries to view playback.
        4. Manual Recording on from the NVR: This allows the user to override the recording schedule for your cameras and manually decide when a camera should record. Only give this option to trusted users.

Once you have completed the permissions for your new user, click the “OK” button on the bottom right-hand side. This will take you back to the User screen.

Setting Up Motion Recording Via Web Interface

Motion detection recording allows you to only record footage when there is activity in any of the areas that you are monitoring, making it easier to search for events recorded and also allowing your system to conserve disk space on your NVR’s hard drive.

Step 1. Navigating To The Motion Settings

1. Open the recorder web login by typing the recorders local IP address / external IP / DDNS into the Internet Explorer web browser.
2. Click “Download” at the top of the page to install the web plugin. Make sure you close your browser during the installation.
3. Reopen the recorders login page and login using your user name and password (Default is Username: admin Password: 123456)
4. Once you are logged in navigate to the “Settings” button at the top of the screen
   
5. . Once in the “Settings” menu on the left hand side navigate to “Camera > Motion”
6. All of your motions settings will be found in this menu. The first setting that will need to be configured is the “Area”. To set up the area for detection first click on “Start Drawing”, next on the image provided to the left start in the corner and drag and drop a red grid over the whole image.
   
7. Next make sure that the “Motion” setting is check to the “On” Position.
8. Every situation is different where the camera will be installed. Typically setting the sensitivity to 50 is recommended, then adjusting from there if needed. Either lowering if too many false triggers occur, or raising it if little to no triggers occur
9. Setting the Arming Schedule will be the next tab over.(time when actions will be
   triggered). We usually recommend keeping this at 24/7, but every situation is different!
   
10. Next setting to set up is going to be the “Trigger Actions”. The trigger actions are set up to the camera what to do when motion is detected. The main setting that you want to make sure you have set is the “Trigger Recording”. When setting the trigger reordering setting you want to check on the channel that you are currently configuring, for example if you are configuring motion for camera one in the trigger recorder menu “D1” would be checked on while all the other are unchecked and if you were configuring channel 5 under trigger recorder “D5” would be checked on while all the other were unchecked.
    

Key

• Conventional
  • Buzzer – The NVR’s Speaker will beep when event is triggered.
  • Send Email – NVR will send an Email when Event is Triggered
• Alarm Output – When an event is triggered, the NVR can enable a built in alarm output for a siren, light, etc.
• Recording – When Event is triggered for the particular cam, the NVR will start recording on cams that are checked
• Snapshot – When Event is triggered on the particular camera, the NVR will take a snapshot of any cams that are checked
• Goto Preset – When Event is triggered, the NVR can set a PTZ cam to a specific preset

Step 2. Setting Up The Schedule

1. Next thing to set up will be the Schedule on the recorder. To access these setting navigate to “Settings > Camera > Schedule”
2. Pre-Record is for how much data will be saved from before the motion started. Post-Recorder is how long the camera will keep recording even after it has stopped detecting motion.
3. Make sure that “Recording Schedule” is check to the “On” position.
4. First thing you want to think about is if you want the cameras to record all of the time or on motion in this tutorial we are setting up all camera on motion. If you want the camera to record all of the time by default you can leave the schedule at the all blue color.
5. To change the Schedule to motion you can click the “Motion” button on the right and then drag and drop the green color over each day and hour starting in the corner.
6. Other option for setting up the Schedule is you can click on the “Edit” button just above the upper left corner. This will allow you to manual type in each periods start and end times how you want the recorder to record during that time.
   
   
7. You can then use the “Copy to” drop down to copy the schedule to all cameras or you can manual set up each camera by changing the Camera ID at the top.

How to set up Gmail email alerts on a Uniview NVR

This guide will explain each step to set up email alerts on a Uniview NVR using a Gmail account

Note

If you would like to receive E-mail alerts whenever an event has occurred, we recommend using a Gmail account. It’s free, secure, and easy to configure.  If you don’t already have a Gmail account you can create one here.

First, you’ll need to make sure that your Gmail account is configured to allow “less secure apps” to send E-mail to your account from the NVR.

1. Log into Gmail with your user name and password, then click on your account icon in the top right. Our account has been customized with the Nelly’s “N”.  Yours might have a default user icon.

2. Then click on the “My Account” button:

3. Then click on “Sign-in & Security” on the left:

4. 2-Step Verification: Turn on 2 Step Verification if it’s not enabled, otherwise the setting you need to enable will not be displayed.

5. Now there should be an option for “App passwords” underneath 2-Step Verification. Select this option, Select App and choose “custom” and name it NVR/DVR and it will generate an app password that you will need to save for later.

6. Now that 2-step verification and app passwords are enabled the next step is to log into your NVR by opening a web browser and typing in the IP address.   Alternately, if you have the EZTools software you can click the “e” icon on the right to open the NVR in a web browser.

7. Once you’re logged in to the NVRs web interface go to Setup->Network->Email.  (Click to view full size)

8. First turn the Server Authentication to On, this is required by Gmail.  Next insert each field as explained below:

Username: Full Gmail email address  (ex. nellyssecurity@gmail.com)

Password: Generated App Password

SMTP Server: smtp.gmail.com

SMTP Port: 587 – Check the TLS/SSL box

Snapshot Interval: Check the box to attach a snapshot to the email when an event has occurred

Sender: NVR

Sender’s Address: Full Gmail email address

Select Recipient: Here you can choose to send to multiple people

Recipient: The name of the person receiving the email alerts

Recipient Address: Full Gmail email address of the person that will receive the email alerts

Schedule: Whenever you want the emails to send.  By default they are set to send all day every day if they are triggered.

9. Once all the information is in click Save.  Next click the Test button next to “Recipient Address” to send a test email to the specified email address.

10. Lastly, you will need to check the “Send Email” box for the event you want to trigger the alerts.  (Motion Detection, Cross Line Detection, etc)

If you want to set up email alerts for regular motion detection go to Camera->Motion.  The check box can be found under the Trigger Actions tab.

How To Manually Upgrade a UNV NVR Via Web Interface

If your NVR is accessible on the local area network using the web interface, you may update the
firmware using a file that has been downloaded and stored locally.

Within the Setup section of the web interface, go to the Maintenance section and select the Local Upgrade entry. On the screen that comes up, click on the Browse button next to the Upgrade text entry field and browse to the location on the local PC where the firmware file is stored and click on it. Once the file is properly entered, press the Upgrade button and the unit will perform the upgrade procedure including a reboot which will terminate your connection.

Please Note

If you download a firmware off the Nelly’s website, you must export the Zip Folder out of the initial Zip Folder that is downloaded.

Adding Blank UNV Camera To UNV Retail NVR via Plug n Play

In scenarios where a Blank UNV camera is paired with a UNV Retail NVR, these will be plug n play. However, you may not get the full functionality of the Blank UNV Camera right away.

In this guide, we will show you the steps needed to allow the full functionality of the Blank UNV Camera.

Connecting The Camera

Since the Blank UNV cameras are plug n play with UNV Retail NVRs, the camera will come online if it is connected directly to the integrated POE switch of the NVR.

Camera Configuration via NVR

One thing you may notice however, the camera will show added with the ONVIF protocol. This can be very limiting as ONVIF only guarantees a live view and 24/7 recording.

If you go into the Smart Event section of the NVR while the camera is added via ONVIF, you will notice that none are available:

To accommodate for this, Go to Setup -> Camera -> Cameras. Checkmark the Camera, select Modify, change the Add Mode to IP Address, then change the Protocol to Uniview. Save.

Now that the camera is talking via the Uniview protocol, the Smart Events are now available!

Please Note

Not all UNV cameras support Smart Events, be sure to verify what events the camera supports beforehand! If you are unsure what events a camera may support, feel free to contact our Support or check the camera’s spec sheet.

Also Note

This guide will work along with UNV Retail Cameras and UNV Blank NVRs. Just the protocol will be changed to Private instead of Uniview on the Blank NVR.

Getting Started with ClareVision – WiFi Cameras

Overview

The following article provide the following information:

• Setting up your WiFi camera
• Configuring motion, image, and event settings
• Adding the camera to the ClareVision App

 Step One: Connect the Camera to Your LAN

To add the camera to a WiFi network, first connect the camera to the Local Area Network (LAN) through a router, modem, or network switch.

1. Using an Ethernet cable, connect the WiFi camera to a router, switch, or modem that is on the network you would like to configure WiFi for.
2. Power up the camera using the included power supply (Bullet and Turret cameras)
3. Once the camera has connected to the network, use the IP Search Tool to discover the camera IP Address.

IMPROTANT: The WiFi Turret (CLR-V100-4T36WF-W) and Bullet (CLR-V100-4B36WF-W) do not support POE. You must connect the camera to the network using an Ethernet cable and power the camera with the included power supply.

ClareVision Cameras Setup Guide

Read Next :

• ClareVision Camera and NVR Setup Documentation
• ClareVision Camera and NVR Firmware
• Hikvision AX PRO Configuration Full Setup &#8211; Video

Step Two: Discover the Camera

All Clarevision cameras ship with DHCP turned on. DHCP simply means the router will assign an IP address to the camera when it boots up using the LAN IP address scheme. Example:

• Router IP Address: 192.168.1.1 (typical)
• IP address range that may be available: 192.168.1.2 through 192.168.1.255
• Router will assign an address like this: 192.168.1.x, where x can be any number between 2 and 255.

1. Install and launch the IP Search Tool and select “Search”
   
2. Open a Chrome or Edge browser and input the WiFi camera’s IP address into the URL field on your web browser
   
3. Input the default username and password.

IMPORTANT:

The default username is: admin

The default password is the first six characters of the UUID. The UUID can be found on the camera label or the quick start guide. If those are not available or inconvenient, you can use one of these methods found HERE to discover the UUID.

Tip:

When you login, you will be asked to change the password and answer security questions. Make sure you configure the security questions and store them. If you do not and you lose the password you will have to go to the camera and physically reset it.

Step Three: Update the Camera to the Latest Firmware Release

Clare Controls releases camera firmware with new features about once every four months. Chances are, your camera will need to be updated when you take out of the box. The camera firmware database is located here.

1. Log into the camera and go to the Configuration > System Configuration > Device Information to review the firmware version.
2. Cameras with version numbers where the last 3 digits are lower than 30.x will require you to to to the maintenance tab and upload the firmware to the camera you retrieved from our website. Cameras with version numbers greater than 30.x will have online update services directly from the web console as shown below:
   
3. Simply click on the “Check” button and the camera will check our servers for an update and if available ask you if you want the camera updated. Updates take about 3 minutes.

Step Four: Configure the WiFi Settings

Make sure the camera is connected to a router, switch, or modem before proceeding with the next steps.

1. Select WiFi Configuration on the home page or navigate to Configuration > Network > Advanced Setup > WiFi.
   
2. Tap Scan to discover available WiFi 2.4GHz WiFi networks.
   
3. Select the desired WiFi network you would like to connect the camera to.
   
4. All fields should automatically populate when you select a WiFi network. Input the WiFi password into the Key field.
   
5. Check DHCP if you would like the network to assign the network parameters automatically. Leave this field unchecked if you would like to manually configure settings such as IP Address, Netmask, Default Gateway, and Preferred DNS Server.
   
6. Tap Save to complete and save your configuration.
   

Step Five: Configure the Video Stream

Video stream: the IP Camera streams one or more streams to mobile apps, NVR’s and integrated systems. The video settings control the configuration of those streams. Image settings control the parameters that affect the way the image is captured.

The video stream is configured through two basic menu items: Video and Image.

ClareVision Cameras are configured for best optimal settings out of the box. You will most likely not need to adjust settings unless specific settings require it. You can adjust image settings under Configuration > Image > Image Adjustment.

Tip:

We have configured the encoder for H.264 encoding on all streams. You may want to encode the main stream (stream 1) using H.265 as it requires about 50% of the network bandwidth and 50% of the HDD storage space vs. H.264. We set the main stream to H.264 because certain control systems and mobile phones do not decode H.265. You can tune this to your application.

Step Six: Configure Events

Events are the heart of the intelligent camera. All configuration is found under the Configuration Tab/Events. Events are broken into two categories: motion and smart.

The standard configuration for events from the factory is as follows:

• Motion detection: enabled, full field (entire field of view
• Motion sensitivity: 5 (medium) – will detect a human about xx feet for Value Series and yy for Performance Series
• Motion record calendar: 7×24
• Motion event arm calendar: 7×24
• Motion record: main stream (except V100 4mp, which is set to sub-stream)
• Smart event: disabled

1.   Determine whether you want to use Smart Events or Motion Events:

• 1. Smart Events: detects human objects only and is quite accurate. Use this when other objects, like vehicles are not required. Smart events include intrusion zone, line cross detection, loitering and people gathering. False positives with Smart Events are very rare.
  2. Motion Events: detects motion of any kind (human, package, vehicle, animal)

Tip:

When using the camera stand alone, do not set up more than one event type (motion, smart). It is the event arming action that sends the event to the push notification server and the recording engine inside the camera. The camera will only record ONE event type (motion OR smart). If you arm both, you will get both event types sent to the user as push notifications but only one will record. The user could then receive a push notification for which there is no recording.

2.   Go HERE for details on setting up motion events

3.   Go HERE for tips on setting up smart events.

Step Seven: Configure Storage

While you may store events locally to the SD Card and to an NVR at the same time, in this example, we will discuss the SD Card storage only.

1.   Go to Configuration > Storage > Recording Schedule.
Set the storage schedule and event type you wish to store.

Tip:

It is the COLOR of the bars that indicate the events that are going to be recorded NOT the drop down box above.

Caution:

Always set the recording schedule to 7×24 and use the EVENT ARMING calendar to control when something will actually be detected, recorded and a push notification sent.

2.   Click on storage management to see the status of the SD Card. If it needs to be formatted it will indicate that, simply press the FORMAT button. The SD Card overwrites by default.

3.   Advanced properties allows you to control the pre-record and post record interval. When an event is detected in the example below, the camera will store the 5 seconds leading up to the event and 10 seconds after the event ends.

Step Eight: Add the Camera to the Mobile App

Now that you have set up your camera, it is time to add it to the ClareVision app. It is quite simple.

1. Launch the ClareVision App
   
2. Tap the ‘Plus’ sign and you will be presented with the three options shown below.
   
3. If you tap device is on the network, the app will scan the LAN for any ClareVision cameras and present them in the following screen. Device is on a remote network provides you with the option of scanning a QR code for a camera on a remote network.
   The system will locate it anywhere in the world and provide you with a login screen to add the remote camera.In our example, we tapped on “Device is on the local network” and two devices were found.
   
4. Tapping on a device brings you to a login screen where you may enter the credentials
   
5. And DONE!
   

You have just successfully installed, configured and enabled a stand alone ClareVision camera on the ClareVision mobile app. Any push notifications and events that are configured  will automatically propagate to your customer’s mobile device.

Getting Started with ClareVision – Standalone Camera Setup

The following is a getting started guide to for ClareVision cameras…it is the basics.

Overview

The following article provide the following information:

• The basic functions of an NVR
• The basic functions of an IP camera
• Best practices for setting up a stand alone camera

NVR’s

The NVR provides two basic functions: it network attaches the cameras and provides storage. In fact, the NVR does very little else.

• Network services: the NVR provides a central place to access IP cameras. You can attach IP cameras directly to the ports of the NVR or leave the cameras on the LAN. The NVR can be configured attach to those cameras for purposes of centralized access and recording. Centralized access can be viewing on the web console or providing access to integrated solutions such as the ClareOne Panel or a home automation system such as Control4
• Recording services: the NVR also provides recording services. You may record full time video or motion events, smart events, alarm events or any combination.

Note:

The NVR does NOT create events. The camera creates all events and the NVR simply records them. Why are the settings in the NVR for motion events, smart events and alarm events? Convenience. The NVR is simply configuring the camera so you do not have to log into each camera to configure an event. Check it out: configure an event in the NVR and log into the camera. You will see the exact settings you configured in the NVR in the camera settings web console.

Tip:

Since many ClareVision cameras come with SD cards installed, when should I use an NVR?

• Full time recording: the SD Cards are not useful for full time recording. A 4MP camera will overwrite in less than one day on full time record
• Storing multiple event types: the camera will store motion OR smart events OR alarm events. Use the NVR if you need multiple event types stored
• Camera count: if you are getting above 2 to 3 cameras, it is probably time for an NVR. Centralized access and storage flexibility will be very useful in those use cases.

IP Cameras

The IP camera is where almost everything interesting happens. The IP camera collects, analyzes and forwards video streams and snapshots to one or more clients. The camera can provide service to a mobile app, the NVR and an integrated control system simultaneously. It also provides multiple streams of video in different resolutions and frame rates so the client device can select the stream it can process. The following provides a high level reference highlighting the differences between the Value Series and Performance Series ClareVision IP cameras:

Feature	Value Series	Performance Series
Motion
Advanced Motion
Smart Events
Streams	2	3
Starlight
Available Varifocal
Fixed Lens	3.6mm	2.8mm
Color at Night		Coming Soon

In summary, the camera is where everything interesting happens. The NVR simply provides convenient access and storage.

Next, let’s set up a camera, stand alone and attach the ClareVision mobile app….

Setup a Stand-Alone ClareVision Camera, Connect to ClareVision Mobile

What You Need

Learning by doing is far better than reading articles and watching videos. Before you proceed, you will need the following:

• ClareVision IP camera: we will use a Performance series camera in our exercises.
• A computer with internet access
• A mobile phone with ClareVision installed. (Do not install ClareVision Plus – that is our legacy app)
• A PoE switch or a standard ethernet switch with a stand alone PoE injector.

Step One: Install the Camera on Your LAN

The following image shows the connection scheme for a PoE switch connected to a camera.

Tip:

If you are using a PoE switch, most switches have two LED’s on them: power and link. The power LED indicates the switch is powering the camera and the link light indicates data is being transmitted to the camera. Both of these LED’s should be lit. The link light will often flash.

If your link light is flashing on the ethernet switch and the power LED is lit – you have powered up the camera. Success!

Step Two: Find the Camera on Your LAN

All Clarevision cameras ship with DHCP turned on. DHCP simply means the router will assign an IP address to the camera when it boots up using the LAN IP address scheme. Example:

• Router IP Address: 192.168.1.1 (typical)
• IP address range that may be available: 192.168.1.2 through 192.168.1.255
• Router will assign an address like this: 192.168.1.x, where x can be any number between 2 and 255.

Tip:

While you can simply launch the mobile app, discover the camera and configure the password change, we DO NOT recommend this as a best practice. Many configuration parameters and all Smart Events are configurable from the web console only. Take the time to tune the camera to the installation, it will pay dividends in customer satisfaction!

How do you find your camera so you can login and configure? Download the IP search tool here.

Install and Launch IP Search and select “Search”

All IP cameras and NVR’s regardless of their IP address will appear in the results window.

Next launch a web browser (Chrome or Edge) and enter the IP address of the camera you just installed.

The default USERID is: admin (not case sensitive)

The default password is the first six characters of the UUID. The UUID can be found on the camera label or the quick start guide. If those are not available or inconvenient, you can use one of these methods found HERE to discover the UUID.

Tip:

When you login, you will be asked to change the password and answer security questions. Make sure you configure the security questions and store them. If you do not and you lose the password you will have to go to the camera and physically reset it.

Step Three: Update the Camera to the Latest Firmware Release

Clare Controls releases camera firmware with new features about once every four months. Chances are, your camera will need to be updated when you take out of the box. The camera firmware database is located here.

Log into the camera and go to the Configuration tab and click on System Configuration/Device Information to review the firmware version.

Cameras with version numbers where the last 3 digits are lower than 30.x will require you to to to the maintenance tab and upload the firmware to the camera you retrieved from our website. Cameras with version numbers greater than 30.x will have online update services directly from the web console as shown below:

Simply click on the “Check” button and the camera will check our servers for an update and if available ask you if you want the camera updated. Updates take about 3 minutes.

Step Four: Configure the Video Stream

Video stream: the IP Camera streams one or more streams to mobile apps, NVR’s and integrated systems. The video settings control the configuration of those streams. Image settings control the parameters that affect the way the image is captured.

The video stream is configured through two basic menu items: Video and Image.

Here’s the good news. You likely will not have to adjust any video settings. We have configured those to allow for seamless integration into the ClareOne system and third party control systems.

Tip:

We have configured the encoder for H.264 encoding on all streams. You may want to encode the main stream (stream 1) using H.265 as it requires about 50% of the network bandwidth and 50% of the HDD storage space vs. H.264. We set the main stream to H.264 because certain control systems and mobile phones do not decode H.265. You can tune this to your application.

You likely will not touch any image settings except image rotation. Clare put a lot of time into optimizing all settings. We believe you will agree when you see the image quality!

Here is the image rotation setting:

That’s it! You are done with video and image settings!

Step Five: Configure Events

Events are the heart of the intelligent camera. All configuration is found under the Configuration Tab/Events. Events are broken into two categories: motion and smart. (V200 only).

The standard configuration for events from the factory is as follows:

• Motion detection: enabled, full field (entire field of view)
• Motion sensitivity: 5 (medium) – will detect a human about xx feet for Value Series and yy for Performance Series
• Motion record calendar: 7×24
• Motion event arm calendar: 7×24
• Motion record: main stream (except V100 4mp, which is set to sub-stream)
• Smart event: disabled

1.   Determine whether you want to use Smart Events or Motion Events:

• 1. Smart Events: detects human objects only and is quite accurate. Use this when other objects, like vehicles are not required. Smart events include intrusion zone, line cross detection, loitering and people gathering. False positives with Smart Events are very rare.
  2. Motion Events: detects motion of any kind (human, package, vehicle, animal)

Tip:

When using the camera stand alone, do not set up more than one event type (motion, smart). It is the event arming action that sends the event to the push notification server and the recording engine inside the camera. The camera will only record ONE event type (motion OR smart). If you arm both, you will get both event types sent to the user as push notifications but only one will record. The user could then receive a push notification for which there is no recording.

2.   Go HERE for details on setting up motion events

3.   Go HERE for tips on setting up smart events.

Step Six: Configure Storage

While you may store events locally to the SD Card and to an NVR at the same time, in this example, we will discuss the SD Card storage only.

1.   Go to Configuration/Storage/Recording Schedule

Set the storage schedule and event type you wish to store

Tip:

It is the COLOR of the bars that indicate the events that are going to be recorded NOT the drop down box above.

Caution:

Always set the recording schedule to 7×24 and use the EVENT ARMING calendar to control when something will actually be detected, recorded and a push notification sent.

2.   Click on storage management to see the status of the SD Card. If it needs to be formatted it will indicate that, simply press the FORMAT button. The SD Card overwrites by default.

3.   Advanced properties allows you to control the pre-record and post record interval. When an event is detected in the example below, the camera will store the 5 seconds leading up to the event and 10 seconds after the event ends.

You have just professionally configured a ClareVision camera! 

Step Six: Add the Camera to the Mobile App

Now that you have set up your camera, it is time to add it to the ClareVision app. It is quite simple.

Launch the ClareVision App

Tap the ‘Plus’ sign and you will be presented with the three options shown below.

If you tap device is on the network, the app will scan the LAN for any ClareVision cameras and present them in the following screen. Device is on a remote network provides you with the option of scanning a QR code for a camera on a remote network. The system will locate it anywhere in the world and provide you with a login screen to add the remote camera.

In our example, we tapped on “Device is on the local network” and two devices were found.

Tapping on a device brings you to a login screen where you may enter the credentials

And DONE!

You have just successfully installed, configured and enabled a stand alone ClareVision camera on the ClareVision mobile app. Push notifications and events as configured will automatically propagate to your customer’s mobile device!

Configuring Motion Events in a ClareVision Camera

The following a is a quick guide to setting up motion events in a ClareVision camera.

Motion events are quite simple to set up.

Step One: Go to the configuration tab, Events/Motion Events

Step Two: Set the motion area.

Set the motion area by dragging your mouse over the grid pattern. The area without grid coverage will not be analyzed for motion. In the image above, the pool surface should be removed from the motion detection area as the spa spillway will create rippling on the surface of the pool which will result in false triggers.

You should also watch for nearby bushes/trees/foliage that may move when the wind is blowing. The motion algorithm in the ClareVision cameras was overhauled in the fall release. As a result, insects, birds and foliage in the distance will rarely cause false triggers.

Step Three: Tune the Sensitivity.

As you lower the sensitivity, the likelihood of false triggers will be reduced, but the camera’s detection zone for a human size object will also be reduced. See the table below:

Note:  the above table is for human sized objects and the fixed lens cameras.  Cars, for example, will trigger motion events at greater distances and zoom adjustment on a varifocal camera will allow you to detect human objects at greater distances than those listed above.

Step Four: Set the arming schedule.

The arming schedule is what controls when the camera will process motion events. When a motion event is created, it is automatically sent to the push server (stand alone) or sent to the NVR for processing. Additionally, when a motion event is created, it will be sent to the recording engine in the camera and if configured to record, it will be recorded to the SD Card.

The arming schedule default is 7×24.

Caution:

It is easy to get confused by the multiple calendars that are in a camera or NVR. The event arming schedule shown above is the primary calendar you need to manage.

If your installation requires events to be disabled during certain hours of the day or days of the week ALWAYS do the following:

1. Use the event arming schedule to control when the event will be analyzed and propagated

2. Leave the record schedule on 7×24 record. DO NOT try to match the two calendars – use the event arm schedule to control when events happen NOT the record schedule.

Step Five: TEST

This is an easy thing to skip – make sure you test your setup! Watch the area of interest and make sure objects moving in that area are captured (go to the Playback tab to view). Equally as important, make sure you have filtered out areas that are prone to create false triggers: nearby foliage, pools, sidewalks, roadways etc.

Configuring Smart Events in Standalone Performance Series ClareVision Cameras

The following a is a quick guide to setting up Smart Events in standalone Performance Series ClareVision cameras.

Step One: Go to the configuration tab, Events/Smart Events

Make sure you ENABLE Intelligent Detection such as Humanoid detection. You must have Intelligent detection enabled to use any of the presents below.

There are four smart event types:

• Intrusion: intrusion events are boundary intrusion events. Intrusion detection can be configured with up to four zones.
• Line Crossing: line crossing detection can be configured as a unidirectional crossing or bidirectional crossing.
• Loiter Detection: detects when people stay in a region of interest for an certain time period.
• People Gather: detects when the density of people in an area exceeds a threshold.

All of these events are human based. Vehicle detection is being worked on at this time and will be in a future firmware release.

Although there are four smart event types, they all are stored and propagated to the mobile app as ‘Smart Events’. There is meta-data that indicates the smart event type in the event log in the mobile app and in the push notification. You can configure more than one smart event type.

Step Two: Intrusion

Intrusion is the most commonly used smart event type. It is similar to motion detection in concept but is restricted to human detection. False positives are very rare with smart intrusion events.

First – check the ‘enable’ box. Without the event enabled, nothing will happen.

Click “Draw Area”. You can draw a quadrilateral anywhere on the screen. If the region of interest does not fit nicely within a quadrilateral, you can draw a second quadrilateral by using the “Warn Region” dropdown box. You can have up to four regions of interest.

Any intrusion in any of the up to four regions will trigger the intrusion event.

The “Time Threshold” is the duration the person needs to be in the region for the event to trigger. The time is in seconds.

“Sensitivity” is the human detection sensitivity setting. A higher number will detect humans further away from the camera, but may be prone to more false detections. Lower sensitivity has the reverse effect.

Step 3: Line Crossing

Line crossing is used when you want to know when someone has entered or exited a specific threshold or doorway as opposed to simply knowing if someone is in a region

In this example, the camera will trigger when someone walks from the house to the pool, but not the reverse.

Step Four: set the arming schedule.

The arming schedule is what controls when the camera will process smart events. Each smart event type can have its own arming schedule. When a smart event is created, it is automatically sent to the push server (stand alone) or sent to the NVR for processing. Additionally, when a motion event is created, it will be sent to the recording engine in the camera and if configured to record, it will be recorded to the SD Card.

The arming schedule default is 7×24.

Caution:

It is easy to get confused by the multiple calendars that are in a camera or NVR. The event arming schedule shown above is the primary calendar you need to manage.

If your installation requires events to be disabled during certain hours of the day or days of the week ALWAYS do the following:

1. Use the event arming schedule to control when the event will be analyzed and propagated

2. Leave the record schedule on 7×24 record. DO NOT try to match the two calendars – use the event arm schedule to control when events happen NOT the record schedule.

Step Five: TEST

This is an easy thing to skip – make sure you test your Smart event! Watch the area of interest and make sure objects moving in that area are captured (go to the Playback tab to view). You can use the sensitivity setting to adjust the distance the camera will pick up a human event.

Where to find the default password for ClareVision Cameras and NVRs

The default password for all ClareVision cameras and NVRs is the FIRST SIX CHARACTERS of the UUID which can be found on:

• Back of the installation manual
• Label on the camera box
• Label on the back of the physical camera

IMPORTANT NOTE: The password is case sensitive.

You will be prompted to change the password when initially setting up the camera in both the camera web console and ClareVision App.

How to use the SD Card in a ClareVision Camera as Backup to Your NVR.

Want to be sure events are available for your customer in the event of an NVR failure or NVR theft? Use the SD Card on the Camera as a backup.

Overview

The SD Card in the camera (included in all 4MP and 2MP fixed lens ClareVision cameras) is a useful tool when you want to install one or two cameras and keep the job low cost and simple.  The user experience is similar to an NVR with event playback and the storage is reliable.  What about an installation with an NVR?  Use the SD Card as a back up for events.

NVR Setup

The NVR setup is not changed in any way to accomplish the goal of using the SD Card as a backup for events.  Read this article to learn more about setting up a ClareVision NVR.  Once you have completed setting up the NVR to record motion or smart events, you are ready to configure the camera to record events.

Camera Setup

By setting up the NVR to record events in the motion or smart event setup, you have already configured the camera’s motion or smart events.

Here is the NVR with smart events configured using Intrusion Detection

By configuring the Intrusion Detection in the NVR as above, the camera Intrusion Detection is configured as shown below (the NVR simply ‘programs’ the camera)

The recording schedule you setup in the NVR is the recording schedule for the NVR, not the camera.  To use the camera SD card as a backup to the NVR for events, we need to set the recording schedule up in the camera.

The image below shows the camera recording schedule.  It is set to record all Smart Events, 7 days/week, 24 hours/day.

Save the schedule and you are done.  The camera will both, send the event to the NVR for storage and record the event locally.

Points to Remember:

1. You cannot access SD Card events from the mobile app when it is behind an NVR (i.e. on the PoE ports).  If the camera is connected to the NVR on the general network, you can add the camera to the mobile app as a separate device and access the events directly from the camera tile on the home page.  We only recommend doing this for troubleshooting and access to SD Card events as it will get confusing for your customer if the camera is visible on the home page and the NVR screen.
2. You can only back up ONE event type: motion OR smart and not both.  The camera will only record a single event type.
3. Accessing the stored events on the camera itself involves the following steps assuming the camera is on an NVR PoE port:
   1. Log into the NVR
   2. Go to Configuration/Channel/Camera
      
   3. Access the virtual host by clicking on the IP address of the camera you wish to view and login to the camera.
   4. Once logged into the camera, go to the Playback tab and view the stored events.

Conclusion

Clare Controls includes SD cards on many of its cameras standard.  You can use the camera stand-alone OR use the SD card as a backup to the NVR.  With a few minutes of work, you can assure you customer their data is safe!

Where do I find the UUID on an Installed Camera

If you camera is already installed and you need the UUID for setup – follow these instructions.

Let’s say you are being called out to configure cameras that have already been installed and no one wrote down the UUID you need for the password. There are two simple methods for retrieving the UUID without getting a ladder out and going to each camera

Method 1: Cameras are Stand-Alone on the LAN

Launch the ClareVision App

Tap the ‘Plus’ sign and you will be presented with the three options shown below.

If you tap device is on the network, the app will scan the LAN for any ClareVision cameras and present them in the following screen.

There you have all ClareVision cameras attached to the LAN with the UUID (needed for the default password) and the IP address of the camera. You can now log into the camera your browser using the IP address and the first 6 digits of the UUID as the default password.

Method 2: Cameras are on the NVR

This is even easier. Log into the NVR, change the password as requested. When you do so, all attached cameras will have their UserID and password set automatically to the UserID and password of the NVR.

If you want to change the UserID and password of the NVR, you do so under the Configuration tab System/Users

Check the “Sync Camera Password” box and password will change on all attached ClareVision cameras whether on the PoE ports or the general LAN when the NVR password change is accepted.

Note:

The camera password sync feature works with ClareVision cameras only. It does not work with attached ONVIF cameras (e.g. Luma, Hikvision etc)

How to set up Event Snapshots using cloud storage for ClareVision cameras and NVRs

Event snapshots can be configured for ClareVision cameras and NVRs that are backed up on a Google Drive account. Whenever an event is detected such as smart event, motion, or other alarm trigger, a snapshot image will be created of the scene and uploaded to your Cloud storage device. This guide will help you set up Google Drive for use as a backup with event snapshots.

Google Drive:

1. Utilize IP Search Tool to find your camera on the network and notate the IP address.
2. Open Edge or Chrome and navigate to the IP address for your camera.
   • (ex. http://10.100.0.100)
3. Log into the camera using camera’s credentials that you created at setup.
4. Click on the “Configuration” tab, then click on “Storage” in the navigation tree on the left side of the page.
   
5. Click on the “Storage Management” sub-menu and switch to the “Cloud Storage” tab.
6. From the drop-down menu in a camera, select “Google” or the “Enable” checkbox and “Google” checkbox on an NVR. The web console will auto-fill with the Web setup URL and Authentication Code. You will need this code to complete setup.
   
7. Copy and past the web browser URL link (https://www.google.com/device) into a new browser tab.
8. Copy and paste the Authentication code into the Google devices login window and tap “Next“.
   
9. Log in or select your Google Drive account.
10. Tap “Allow” to give the NVR rights to your Google Drive.
    
11. After the success screen displays, switch back to the camera web console and tap “Bind“.
    
12. The camera is now be connected with your Google Drive account. You must enable Cloud Snapshot Backup individually for each camera including those connected to an NVR by opening the camera through the Virtual Host. Configure the Cloud Linkage method in your motion detection settings:
13. Open the “Events” window in the sub-menu and select “Ordinary Events or Smart Events“, depending on the need.
14. Under your selected event type, select “Linkage Method” in the sub-menu.
15. Add a check box next to “Upload Via Cloud” to have event snapshots loaded into the cloud.
    
16. Tab “Save“.
17. The next time motion is detected, a folder will be created in your Google Drive that will capture and upload snapshots of motion events.

Where to find the default password for ClareVision Cameras and NVRs

• Back of the installation manual
• Label on the camera box
• Label on the back of the physical camera