IPC – XVRAID XVR-DVR-NVR CCTV DESK https://www.xvraid.com security and surveillance blog Fri, 26 Apr 2024 15:44:13 +0000 en-US hourly 1 https://wordpress.org/?v=7.1 https://www.xvraid.com/wp-content/uploads/2022/02/ipcam.png IPC – XVRAID XVR-DVR-NVR CCTV DESK https://www.xvraid.com 32 32 Verkada intercoms setup guide v1 https://www.xvraid.com/guide/verkada-intercoms-setup-guide-v1.html https://www.xvraid.com/guide/verkada-intercoms-setup-guide-v1.html#respond Fri, 26 Apr 2024 15:41:59 +0000 https://www.xvraid.com/?p=5665 Verkada intercoms setup guide v1, Verkada’s intercom solution enables you to answer calls, grant entry, and secure entrances from anywhere.

Get Started with Verkada Intercom Set up and connect your Verkada intercoms Updated over a week ago

Required. You need Org Admin and/or Site Admin permissions for your Verkada Command organization to complete these actions.

What you need

• PoE-enabled switch or PoE injector
• DHCP-enabled network
• Cat5 or Cat6 cabling

Create a site

Sites are the logical way of grouping and managing devices within your Command organization. Site-level permissions make managing and viewing your devices easier. See Manage Your Sites and Subsites for more information on site creation and management.

Add an intercom

At least one intercom needs to be added to Command before you can see the Intercom tab in the All Products menu. Intercoms can be added to Command from the Devices page. See Add an Intercom to Your Site for more information.

Connect a door

You can pair an existing access-controlled door or wire a door to the intercom that can be unlocked by an intercom receiver. See Configure a TD52 and Wire a TD52 Video Intercom for more information.

Configure receivers

Receivers allow you to answer calls from an intercom and unlock any associated doors. See Add and Configure Receivers in Intercom for more information.

Licensing

Every intercom you manage in Command will need a license. Verkada licensing is applied for each Command organization, and the licenses co-term to a single expiration date. Your licenses may have been automatically added if you claimed your devices via order number. Otherwise, manually add the licenses from the Admin page. See Manage Your Licenses for more information on adding and managing licenses.

Connect your intercom

Recommendation. While Verkada intercoms are considered low-voltage devices that do not require a certified electrician to install, we strongly recommend you work with a system integrator or other professional for installation.

Please refer to the intercom setup guide for instructions on mounting and wiring the door port.

Power and network

Verkada intercoms use Power over Ethernet (PoE) for power and communication over the LAN. In most cases, intercoms will connect directly to an 802.3af PoE standard switch. PoE injectors can be used when a PoE switch is not available. See the intercom’s datasheet for more information.

Check network settings

Verkada intercoms are designed to be plug-and-play. However, if your environment includes a firewall with custom rules and policies, you may need to make some configuration changes to get your access controllers connected to the cloud. See Intercom Network Settings for more information.

Roles and Permissions for Intercom

Roles and Permissions for Intercom

Learn more about Verkada Intercom roles and permissions

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Intercom.

• Permissions are set using roles, which define the level of access users and groups have to devices and settings within an organization and its sites/subsites.
• User permissions specify what tasks users can perform and what features users can access in Command.
• Site-level permissions define what access a particular user or group has to the cameras within the site. Site-level permissions are configured using roles.

See Roles and Permissions for Command users for an in-depth explanation of the features and configurations available for overall Verkada Command usage and administration.

Verkada intercoms setup guide v1

Verkada Intercom permissions determine who can receive calls, view intercom video, and unlock intercom doors. Intercom permissions depend on your site-level permissions, and whether you’re configured as a Receiver.

At a high level, these are the permissions granted to each level of Intercom devices:

screenshot2023 10 31at8 02 52am 605w255h

Site-level roles

Receiver

Required. You must be configured as a receiver to receive calls.

If you’re a Verkada Intercom Receiver, you have the baseline receiver permissions (as shown above). These baseline Receiver permissions combine with site-level permissions to determine overall intercom permissions within a certain site.

For example, if you’re a Receiver for a particular intercom, and a Site Viewer, you get all the Receiver permissions, in addition to the ability to view historical video and events.

Note: Receivers, such as Desk Stations and Session Initiation Protocol (SIP) phones are not tied to a Verkada Command user. This means that the user can only get Receiver permissions, regardless of the user’s site-level permissions.

Regardless of their site-level permissions, a Receiver can:

• Receive calls with video.
• See 24/7 live intercom video, even if not on an active call.
• Unlock the door both during and outside of a call.
• Talk down to the intercom.

Live-View Only

• Receive calls with video.
• See 24/7 live intercom video, even if not on an active call.

Site Viewer

• Receive calls with video.
• See 24/7 live intercom video, even if not on an active call.
• View historical video and events.

Site Admin

• Receive calls with video.
• See 24/7 live intercom video, even if not on an active call.
• View historical video and events.
• Unlock the door both during and outside of a call.
• Unlock the door 24/7.
• Talk down to the intercom.
• Change Receivers and device settings.

.

Verify a user’s eligibility to receive Verkada Pass calls

• A user who has previously logged in to Verkada Pass has a black and white symbol next to their name in the call list. To verify, hover over the Verkada Pass symbol. The tooltip should show Pass App (as shown).

7743538 verkadapass1

• A user who is configured as a Receiver and has never logged in to the Verkada Pass App should show Send Pass App Invite, which you can click to send an invite to that user.

7628594 verkadapass2

.

Set Org Admin permissions

1.In Verkada Command, go to All Products > Admin.
2.Under Org Settings, scroll down to and select Users.
3.Select the user who you want to grant Org Admin permissions.
4.Click the User Actions dropdown and select Grant Org Admin.
5.When prompted to confirm, click Confirm.​

Revoke Org Admin permissions

1.In Verkada Command, go to All Products > Admin.
2.Under Org Settings, scroll down to and select Users.
3.Click the User Actions dropdown and select Revoke Org Admin.
4.When prompted to confirm, click Confirm.

.

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

1.In Verkada Command, go to All Products > Admin.
2.Under Org Settings, scroll down to and select Users.
3.At the top right, click Add User.
4.On Add User:
1.Enter the user’s first name, last name, and email address.
2.(Optional) Check the Grant Organization Admin box to give Org Admin permissions.
3.Click Assign Groups to add them to one or more existing groups,
4.Click Add.
5.Under Site Roles, click Manage Roles and grant the user the desired role for each site and subsite.

Add a group

1.In Verkada Command, go to All Products > Admin.
2.Under Org Settings, scroll down to and select Groups.
3.At the top right, click Create Group.
4.On Create Group, enter the group’s name, and click Create.
5.On Add Members to this Group, check the box next to the members you want to add to the group and click Add.
6.On the new group page, at the top, click Site Roles > Assign Roles.
7.On Assign Roles:
1.Under the Role column, select the permission level you want to assign for each site and subsite.
2.Click Save.

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

1.In Verkada Command, go to All Products > Admin.
2.Under Org Settings, scroll down to and select Users or Groups.
3.Select the desired user or group.
4.At the top right, click Manage Roles.
5.On Manage Roles:
1.Grant the desired site and subsite roles.
2.Click Save.

Manage sites

1.In Verkada Command, go to All Products > Cameras.
2.At the top right of Cameras, click Manage Sites.
3.Select the desired site to manage and in the right pane, click Manage Permissions.
4.Grant the desired roles for users and groups.

Intercom Network Settings

Intercom Network Settings

Learn about the required network settings for Verkada Intercoms

Updated over a week ago

This article outlines the required network settings that your Verkada Intercom needs to communicate with Verkada Command. For more information on the required network settings for other Verkada product lines see Required Network Settings.

Note: Verkada devices are incompatible with LANs that require proxy servers or Secure Socket Layer (SSL)/Transport Layer Security (TLS) inspection. If either is in use, a bypass for all Verkada devices must be implemented for Verkada devices to communicate with Verkada Command.

Status LED

A flashing blue status LED on the top of the intercom indicates the intercom is not communicating with Command. If you see this behavior, check that the network is set up correctly with the intercom’s requirements. If the problem persists, contact Verkada Support.

IP address

Intercoms must be assigned an IPv4 address to communicate on the LAN and to Verkada Command. Intercoms use Dynamic Host Configuration Protocol (DHCP) and User Datagram Protocol (UDP) to obtain their IP addresses and network configurations.

If you require your intercom to have a specific IP address, create a DHCP reservation using the device’s Media Access Control (MAC) address (found on the device’s label).

Domain Name System

Intercoms use the DNS server to resolve Verkada’s fully qualified domain names (FQDN) to IP addresses to communicate with them. Your DHCP server tells the intercom where the DNS server is on the network and the intercom communicates using UDP port 53.

Note: DNS over HTTPS (DoH) is currently not supported.

Power

Intercoms are powered through Power over Ethernet (PoE). This means the network switch needs to provide power to the intercom, or a PoE injector needs to be utilized. For specifics on power requirements, see the Intercom datasheet.

Firewall settings

Intercoms require access to many endpoints to ensure they can communicate with Command and all features will be accessible. Many customers may want to allow the intercoms to communicate with the general required endpoints.

These are the general domains to allow, applicable for all organization-regions:

• *.amazonaws.com – TCP+UDP/443, UDP/1024 to 65535
• *.backblazeb2.com – TCP/443
• *.twilio.com – TCP+UDP 443, 5060, 5061
• *.verkada.com – TCP+UDP/443, UDP/123
• *:4100 – TCP/UDP on LAN
• 34.216.15.26 – UDP/123
• 35.166.49.153 – TCP+UDP/443, UDP/123
• 168.86.128.0/18 – UDP 10000 to 60000
• time.cloudflare.com – TCP/4460 + UDP/123

If your firewall does not allow wildcard masking, or you prefer to have the entire FQDN of the endpoint in your firewall rules, you can add the domains to your allowlist based on the region your devices are in.

Note: Your region is selected when you create an organization in Command.

Region: United States

Standard Verkada Endpoints

• api.control.verkada.com – TCP+UDP/443
• api.global-prod.control.verkada.com – TCP+UDP/443
• api-ga.control.verkada.com – TCP+UDP 443
• device.pyramid.verkada.com – TCP+UDP/443
• device-nlb.verkada.com – TCP+UDP/443
• firmware.control.verkada.com – TCP+UDP/443
• nlb.verkada.com – TCP+UDP/443
• update.control.verkada.com – TCP+UDP/443
• user.pyramid.verkada.com – TCP+UDP/443
• vconductor.global-prod.command.verkada.com – TCP+UDP/443

NTP Endpoints

• 34.216.15.26 – UDP/123
• 35.166.49.153 – UDP/123 + TCP+UDP/443
• time.control.verkada.com – UDP/123
• time.cloudflare.com – TCP/4460
• time.cloudflare.com – UDP/123

Streaming Endpoints

• *:4100 – TCP/UDP on LAN (only required for local streaming)
• index.control.verkada.com – TCP+UDP/443
• relay.control.verkada.com – TCP+UDP/443
• relay.global-prod.control.verkada.com – TCP+UDP/443
• *.kinesisvideo.us-west-2.amazonaws.com – TCP+UDP/443, UDP/1024 to 65535 (webrtc)

Calling Endpoints

• 168.86.128.0/18 – UDP 10000 to 60000
• chunderm.gll.twilio.com – TCP 443†
• ers.twilio.com – TCP 443†
• eventgw.twilio.com – TCP 443†
• verkada-erik-sip.sip.twilio.com – TCP+UDP 5060, 5061
• verkada-erik-sip.sip.us1.twilio.com – TCP+UDP 5060, 5061
• verkada.sip.us1.twilio.com – TCP+UDP 5060, 5061
• verkada-vinter-audio-files-prod1.s3.amazonaws.com – TCP+UDP 443

Access Control Endpoints

• access.control.verkada.com – TCP+UDP/443
• vcerberus.command.verkada.com – TCP+UDP/443

Cloud Backup Endpoints

• s3.ap-southeast-2.amazonaws.com – TCP/443‡
• s3.ca-central-1.amazonaws.com – TCP/443‡
• s3.us-west-004.backblazeb2.com – TCP/443‡
• s3.us-west-2.amazonaws.com – TCP/443‡

Region: Europe

Standard Verkada Endpoints

• api.global-prod.control.verkada.com – TCP+UDP/443
• api.prod2.control.verkada.com – TCP+UDP/443
• api-ga.control.verkada.com – TCP+UDP 443
• update.control.verkada.com – TCP+UDP/443
• vconductor.global-prod.command.verkada.com – TCP+UDP/443
• vconductor.prod2.command.verkada.com – TCP+UDP/443

NTP Endpoints

• 35.166.49.153 – UDP/123 + TCP+UDP/443
• time.control.verkada.com – UDP/123
• time.cloudflare.com – TCP/4460
• time.cloudflare.com – UDP/123

Streaming Endpoints

• *:4100 – TCP/UDP on LAN (only required for local streaming)
• index.prod2.control.verkada.com – TCP+UDP/443
• relay.global-prod.control.verkada.com – TCP+UDP/443
• relay.prod2.control.verkada.com – TCP+UDP/443
• *.kinesisvideo.eu-west-1.amazonaws.com – TCP+UDP/443, UDP/1024 to 65535

Calling Endpoints

• 168.86.128.0/18 – UDP 10000 to 60000
• chunderm.gll.twilio.com – TCP 443†
• ers.twilio.com – TCP 443†
• eventgw.twilio.com – TCP 443†
• verkada-prod2.sip.twilio.com – TCP+UDP 5060, 5061
• verkada-prod2.sip.us1.twilio.com – TCP+UDP 5060, 5061
• verkada-vinter-audio-files-prod2.s3.amazonaws.com – TCP+UDP 443

Access Control Endpoints

• access.prod2.command.verkada.com – TCP+UDP/443
• vcerberus.command.verkada.com – TCP+UDP/443

Cloud Backup Endpoints

• s3.eu-central-003.backblazeb2.com – TCP/443‡
• s3.eu-west-1.amazonaws.com – TCP/443‡

Footnotes:

†required for Desk Stations and Verkada Pass

‡required for cloud backup

Mount a TD52

Mount a TD52

Learn how to mount the Verkada TD52 Video Intercom

Updated over a week ago

Use this article to learn how to mount a Verkada Intercom (TD52). Once you complete the mounting, you can connect the TD52 to the network.

Before you begin

You can mount the TD52 using a flush mount or using a mounting bracket. We recommend that you verify the contents of your box and make sure you have the tools you need

Contents of your box

• TD52 video intercom
• Flush mount plate
• T10 security Torx screwdriver
• 2 grommets
• Grommet punch
• 4 drywall screws
• 4 drywall anchors
• 4 M4x18mm machine screws
• 4 8–32¾” machine screws

Tools you need

• A working internet connection
• A smartphone or laptop
• A #2 Phillips head and power drill
• A level

Choose your mounting option

Whichever mounting option you choose, you should remove the front cover of the TD52 to access the screw holes that allow you to install on a mount.

1.At the bottom of the front cover, with a T10 security Torx screwdriver, remove the security screws.
2.Slide the front cover up and then out.
3.When the front cover is removed there are four screw holes in each corner of the TD52. You use these screw holes to install the TD52 to the mount.

Use a flush mount

The TD52 comes with a flush mount in the box. You can use the screw holes of the flush mount to mount the Intercom (see image below for visual):

• Legacy intercom back box (A)
• Direct wall mounting (B)
• 4 gang junction box mounting (C)

image

• You can use screw holes corresponding to A to mount to an existing intercom back box
• You can use screw holes corresponding to C to mount to a 4 gang junction box

Mount directly to a wall

1.Place and hold the flush mount plate and against the desired surface.
2.Using the mount plate as a template, mark the wall to line up with screw holes labeled “B”.
3.Drill pilot holes in to the wall:
1.For direct mounting, drill a .11 in (3mm) pilot hole.
2.If using wall anchors, drill a .23 inch (6mm) pilot hole.
4.Use the screws supplied to attach the mount plate to the wall.
5.With the flush mount plate on the wall, use the included Torx screwdriver to remove the screws on the bottom of the faceplate (front cover of the TD52).
6.Place the TD52 on top of the flush mount plate and install it using the supplied screws.

Use a mounting bracket

You can use the mounting bracket to install the TD52 on to various surfaces that the flush mount plate cannot, where they’re typically used to mount the TD52 on an exterior surface.

1.Place and hold the mounting bracket against the desired surface.
2.Using the mount as a template, mark surface through screw holes labeled “A”.
3.Drill pilot holes into the wall:
1.For direct mounting, drill a .11 in (3mm) pilot hole.
2.if wall anchors are being used drill a .23 inch (6mm) pilot hole.
4.Use the screws supplied to install the mounting bracket on the wall.
5.With the mounting bracket installed, remove the front cover from the TD52.
6.Place the TD52 on top of the mounting bracket and install it using the supplied screws.

<< Click on the page numbers to go to other pages. >>

]]> https://www.xvraid.com/guide/verkada-intercoms-setup-guide-v1.html/feed 0 Latest Dahua Firmwares 2024 https://www.xvraid.com/firmware/latest-dahua-firmwares-2024.html https://www.xvraid.com/firmware/latest-dahua-firmwares-2024.html#respond Fri, 05 Apr 2024 10:43:31 +0000 https://www.xvraid.com/?p=5211 Latest Dahua firmwares 2024, Dahua Technology is a world-leading video-centric AIoT solution and service provider. The company firmly strengthens its technological strategies that include AloT and IoT digital intelligence platforms, comprehensively promoting the digital intelligence upgrading of cities and enterprises based on customer needs, and creating more value for the digital-intelligent transformation of various industries.

How to Download and Prepare Firmware

Description

This guide will show how to download and prepare the firmware file for a Dahua device.

Firmware files for Dahua devices can be found at Firmware by Device or the specific product page for the device

Firmware is typical provided in a ZIP file, a compressed file format

This file will contain the actual firmware file, which needs to be extracted from the ZIP file in preparation for the upgrade

Prerequisites

• Computer with internet access (to download firmware file)

• Dahua device

Video Instructions

Step by Step Instructions

Confirm the Model and current firmware of Dahua device

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

download and prepare firmware 1

2. Click Info

download and prepare firmware 2

3. Click Version

The Device Type will be displayed

The current System Version will be displayed

download and prepare firmware 3

Download the firmware file for device from DahuaWiki

4. In a browser go to DahuaWiki.com

Under Specifications, Firmware, & Manuals

Click the device type (in this example Recorder)

download and prepare firmware 4

5. Enter the device model into the field

download and prepare firmware 5

6. The results will be filtered

download and prepare firmware 6

7. Click the firmware icon to download the firmware file

download and prepare firmware 7

8. The file will download

download and prepare firmware 8

Extract the firmware file to local computer

9. Right click the Start Menu / Windows icon in the bottom left of the screen

Select File Explorer

download and prepare firmware 9

10. Select Desktop

download and prepare firmware 10

11. Click Home

Then click New folder to create a new folder to extract the contents of the firmware zip file

download and prepare firmware 10 1

12. Find the created folder in the list, double click to open

download and prepare firmware 11

13. Under the Downloads window of the browser, click ‘Show in folder’

download and prepare firmware 12

A new File Explorer window should open containing the directory the firmware zip was downloaded to

Locate the file in the list

download and prepare firmware 13

14. Right click

Select Cut

download and prepare firmware 14

15. Select the window with the new directory

Right click in the window

Select Paste

download and prepare firmware 15

The folder will appear in the directory

download and prepare firmware 16

16. Right click the file

download and prepare firmware 17

17. The contents of the zip file will appear in a new window

download and prepare firmware 18

18. Click to select all files in the folder

Drag and drop the files to the created folder

download and prepare firmware 19

The files will appear in the directory

download and prepare firmware 20

The firmware file will appear in the directory ready to use

download and prepare firmware 21

How to Reset Device to Factory Default

Latest Dahua firmwares 2024

Step by Step Instructions

1. From Live View

Right click select Main Menu

factory reset systemui old 1

2. Under Setting

Click System

factory reset systemui old 2

3. Click Default

factory reset systemui old 3

4. Click Factory Reset

factory reset systemui old 4

5. A prompt will appear to confirm the factory default

Click Yes

factory reset systemui old 5

6. The unit will default and reboot

factory reset systemui old 6

7. When the device has booted back up it will be factory reset and is now ready for device initialization

factory reset systemui old 7

icon for type systemui new

SystemUI New

Step by Step Instructions

1. From Live View

Right click, select Main Menu

factory reset systemui new 1

2. Click Operation

factory reset systemui new 2

3. Click System Maintain

factory reset systemui new 3

4. Click Default

factory reset systemui new 4

5. Click Factory Default

factory reset systemui new 5

6. A prompt will appear to confirm the factory default

Click OK

factory reset systemui new 6

7. The NVR will default and reboot itself

factory reset systemui new 7

8. The unit will boot back up

factory reset systemui new 8

9. The device has been factory reset and is now ready for device initialization

factory reset systemui new 9

WebUI Old

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

factory reset webui old 1

2. Click Setup

factory reset webui old 2

3. Click System

factory reset webui old 3

4. Click Default

factory reset webui old 4

5. Click Factory Reset

factory reset webui old 5

6. A prompt will appear to confirm the Factory Reset

factory reset webui old 6

The unit will reboot and is now ready for device initialization

WebUI New

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

factory reset webui new 1

2. Click Setup

factory reset webui new 2

3. Click System

factory reset webui new 3

4. Click Default

factory reset webui new 4

5. Click Factory Reset

factory reset webui new 5

6. A prompt will appear to confirm the factory default

Click Yes

factory reset webui new 6

The unit will reboot and is now ready for device initialization

Firmware Update via USB Drive

Description

This page will show you how to update the firmware of your Dahua device via a USB drive at the recorder

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device

• USB drive with the firmware file for the device – Firmware by Device

icon for type systemui old

SystemUI Old

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

1. Download Firmware and copy to USB such as a flash drive ➞ Insert USB into recorders USB port.


2. It will prompt for option to upgrade, Click System upgrade ➞ Click Start.

usb upgrade 1

usb upgrade 2

3. Browse for firmware ➞ Open firmware folder is in ➞ Select Bin File ➞ Click Start. Device will reboot once finished.

usb upgrade 3

SystemUI New

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

USB drive with Firmware file should be plugged into USB slot on recorder

1. From the Main Menu, click Operation

how to update firmware via usb newui 1


2. Click System Maintain > Upgrade

how to update firmware via usb newui 2


3. Click the System Upgrade in the middle of the page.

how to update firmware via usb newui 3

4. Select the Firmware file from the list

Click OK

how to update firmware via usb newui 4

5. The firmware update will begin.

Make sure to not unplug the power during this process.

how to update firmware via usb newui 5


6. The NVR will reboot as the final step of the process

how to update firmware via usb newui 6

Firmware Update via WebUI

Description

This page will show you how to update the firmware of your Dahua device via the WebUI

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device with network connection

• Local Windows computer

• Firmware file for device downloaded to computer – Firmware by Device

Instructions

icon for type webui oldWebUI Old

Prerequisites

• Computer

• Internet

• Compatible Browser (Internet Explorer)

• NVR/HCVR/IPC

Video Instructions

Step by Step Instructions

Step 1: From IE(Internet Explorer) type in the devices IP address on the IE address bar → login with credentials.

web upgrade wiki 2

Step2: Setup → System → Upgrade

firmware22

Step 3: Click on “Browse” → Select correct firmware

web upgrade wiki

• Click on “Upgrade”

firmware 3

• Device will reboot after upgrade is finished.

updatebrowser 1

USB firmware Upgrade via web.

If firmware is on USB Device → Click on browse → Navigate to USB location → Select firmware → Open → Upgrade.

updateusb1

updateusb3

updatebrowser 1 1

icon for type webui newWebUI New

Prerequisites

• Dahua device with network connection

• Local windows computer

• Firmware file for device downloaded to computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

firmware update webui new 1

2. Click Operation

firmware update webui new 2

3. Click System Maintain

firmware update webui new 3

4. Click Upgrade

firmware update webui new 4

5. Click Browser

firmware update webui new 5

6. Locate the firmware file

Click Open

firmware update webui new 6

7. Click Upgrade to begin the update process

firmware update webui new 7

8. A message will appear to confirm the upgrade process

firmware update webui new 8

9. When the upgrade is complete the device will reboot

firmware update webui new 9

Firmware Update via SmartPSS

Description

This page will show you how to update the firmware of your Dahua device via SmartPSS

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• SmartPSS installed

• Device added to SmartPSS

• Firmware file downloaded to computer – Firmware by Device

Instructions

icon for type smartpssSmartPSS 2.002

Prerequisites

• SmartPSS installed

• Dahua device added to SmartPSS

• Firmware file for device downloaded to computer – Firmware by Device

Video Instructions

Step by Step Instructions

1. From the Main Page of SmartPSS

Click Device CFG

firmware update smartpss 1

2. Click to select the device from the device tree on the left side of the screen

firmware update smartpss 2

3. Click Upgrade

firmware update smartpss 3

4. Click the folder icon

firmware update smartpss 4

5. Locate the firmware file

Click Open

firmware update smartpss 5

6. Click Firmware Upgrade to begin the firmware update process

firmware update smartpss 6

7. A prompt will appear to confirm the upgrade process

firmware update smartpss 7

8. A prompt will appear to confirm a successful upgrade

firmware update smartpss 8

Firmware Upgrade via ConfigTool

Description

This page will show you how to upgrade the firmware of your Dahua device via ConfigTool

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device(s) with network connection(s)

• ConfigTool installed on a local computer

• Firmware file for device(s) downloaded to computer – Firmware by Device

Step by Step Instructions

Single Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

configtooldevicefirmwareupgrade1 756w457h

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the device you are looking for in Start IP and End IP.
Enter the login information for that device in Username and Password.
Then click OK at the bottom

configtooldevicefirmwareupgrade2

3. Click on Device Upgrade on the left.
Find the device you want to upgrade in the list and click on the Folder icon next to it under the Upgrade File Path column

configtooldevicefirmwareupgrade3 756w458h

4. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

configtooldevicefirmwareupgrade4 700w485h

5. Verify the file path is listed next to the device in the list.
Then click on the Upgrade icon to the right of the device in the Operate column

configtooldevicefirmwareupgrade5 756w457h

6. Click on OK

configtooldevicefirmwareupgrade6 400w313h

7. The progress bar will fill up as the device is upgraded

configtooldevicefirmwareupgrade7 756w458h

8. Once the device has been successfully upgraded you will see a Green Check Mark next to it in the list

configtooldevicefirmwareupgrade8 756w460h

Batch Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

configtooldevicefirmwareupgrade1 756w457h 1

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the devices you are looking for in Start IP and End IP.
Enter the login information for those devices in Username and Password.
Then click OK at the bottom

configtooldevicefirmwareupgrade2 1

3. Click on Device Upgrade on the left.
Find the devices you want to upgrade in the list and check the boxes next to them. (Make sure all devices you check require the same firmware.)
Then click on Batch Upgrade at the top

configtooldevicefirmwareupgrade9 756w458h

4. Click on OK

configtooldevicefirmwareupgrade6 400w313h 1

5. Click on Browse

configtooldevicefirmwareupgrade11

6. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

configtooldevicefirmwareupgrade12 700w484h

7. Click OK at the bottom

configtooldevicefirmwareupgrade13

8. The progress bars will fill up as the devices are upgraded

configtooldevicefirmwareupgrade14 756w458h

9. Once the devices have been successfully upgraded you will see Green Check Marks next to them in the list

configtooldevicefirmwareupgrade15 756w458h

Recorder Firmware Update via Online

Description

This page will show you how to update your Dahua Recorder online.

Note: All devices should be “Factory Reset” once the firmware update is complete.

When the NVR detects there is a newer firmware in the server, a ‘1′ icon will appear at the System icon.

The entire process takes about 5 minutes depending on network connection.

Prerequisites

• Dahua device that supports online update

• Internet connection to Dahua device

Instructions

icon for type systemui new 1

SystemUI

Prerequisites

• Dahua device with internet connection

Video Instructions

Step by Step Instructions

1. From Live View

Right click, select Main Menu

firmware update via cloud systemui new 1

2. Click Operation

firmware update via cloud systemui new 2

3. Click System Maintain

firmware update via cloud systemui new 3

4. The upgrade menu will show if a new firmware version is available

firmware update via cloud systemui new 4

5. Click Upgrade Now to begin the update process

firmware update via cloud systemui new 5

6. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

firmware update via cloud systemui new 6

7. The firmware file will begin to download

firmware update via cloud systemui new 7

8. After the download is complete the unit will automatically begin the firmware upgrade

firmware update via cloud systemui new 8

9. The unit will reboot as the final step of the upgrade

firmware update via cloud systemui new 9

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

From Live View, right click Select Main Menu

firmware update via cloud system ui old 10

11. Click Operation

firmware update via cloud system ui old 11

12. Click System Maintain

firmware update via cloud system ui old 12

13. Click Default

firmware update via cloud system ui old 13

14. Click Factory Default

firmware update via cloud system ui old 14

15. A prompt will appear to confirm the factory default

Click OK

firmware update via cloud system ui old 15

16. The unit will reboot

firmware update via cloud system ui old 16

17. When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

firmware update via cloud system ui old 17

icon for type webui new 1

WebUI

Prerequisites

• Dahua device with internet connection

• Local Windows computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

firmware update via cloud webui new 1

2. Click Operation

firmware update via cloud webui new 2

3. Click System Maintain

firmware update via cloud webui new 3

4. Click Upgrade

firmware update via cloud webui new 4

5. The upgrade menu will show if a new firmware version is available

firmware update via cloud webui new 5

6. Click Upgrade Now

firmware update via cloud webui new 6

7. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

firmware update via cloud webui new 7

8. The firmware file will begin to download

firmware update via cloud webui new 8

9. After the download is complete the unit will automatically begin the firmware upgrade

firmware update via cloud webui new 9

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

firmware update via cloud webui new 13

12. Click Operation

firmware update via cloud webui new 14

13. Click System Maintain

firmware update via cloud webui new 15

14. Click Default

Click Factory Default

firmware update via cloud webui new 17

15. A prompt will appear to confirm the factory default

Click OK

firmware update via cloud webui new 18

The unit will factory default and reboot

When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

Index of /Firmware

Name

Last modified

Size

Description

.

Parent Directory

 .

–

 .

Access Control/

2021-07-13 11:30

–

 .

Dekodery/

2022-11-29 14:22

–

 .

Digital Signage/

2020-10-07 15:08

–

 .

Domofony/

2020-04-10 16:26

–

 .

Kamery -IP- ANPR/

2021-10-12 13:26

–

 .

Kamery -IP- obrotowe- PTZ/

2021-07-05 12:01

–

 .

Kamery -IP- stałopozycyjne/

2022-10-12 13:42

–

 .

Kamery -IP- termowizyjne/

2023-11-20 11:10

–

 .

Kamery-IP- panoramiczne/

2024-03-07 15:08

–

 .

Klawiatury/

2019-11-05 13:59

–

 .

Macierze/

2020-11-17 15:26

–

 .

Monokulary/

2022-11-15 09:43

–

 .

Radary/

2020-06-30 14:42

–

 .

Rejestratory/

2023-03-21 12:24

–

 .

Switche/

2021-07-07 08:27

–

 .

TabliceInteraktywne/

2023-03-24 10:49

–

 .

WiFi/

2020-04-16 11:22

–

 .

_RTMP/

2021-07-08 12:41

–

 .

.

.

]]> https://www.xvraid.com/firmware/latest-dahua-firmwares-2024.html/feed 0 How to Extract and Prepare Firmware nonadult Vivotek NVR Linux based user guide https://www.xvraid.com/guide/vivotek-nvr-linux-based-user-guide.html https://www.xvraid.com/guide/vivotek-nvr-linux-based-user-guide.html#respond Mon, 15 Jan 2024 18:24:32 +0000 https://www.xvraid.com/?p=4627 Vivotek NVR Linux based user guide, VIVOTEK’s ND9425P is a H.265 Linux-based standalone NVR that supports up to 4K IP camera video decoding and local 4K video display. With advanced H.265 compression technology, users are able to experience Full HD quality video while expending less HDD capacity than H.264.

The NVR features embedded 16x 802.3 at/af PoE ports to provide users easy and convenient IP camera installation, and also supports remote and mobile access via VIVOCloud and iViewer apps for both iOS and Android devices. The VIVOCloud app provides instant push notification and direct video playback functions when triggered by an alarm notification and provides users a flexible and intelligent NVR for seamless use in small to medium sized video surveillance applications.

Highlight Feature

.

New Web UI Available for Plug-in Free Browser

C:\Users\msalihaslan\Downloads\nvr_plug-in_free.png

Actively adopting current trends and simultaneously protecting your cybersecurity, VIVOTEK’s new web UI supports Chrome browsers without the need for web plugins. It lets users login and operate with ease, and solves issues related to system administrator authority, safety risks, browser, and OS updates. Furthermore, it now supports H.265 technology meaning that users can attain higher and more efficient image compression rates than previous H.264 systems while maintaining high image quality.

More

Smart VCA Event Search

The NVR supports alarm management and event search of VIVOTEK’s deep-learning video analytics technology, Smart VCA. The user can search by single or multiple event types, playback triggered events and then export these search results to video clips.

.

PoE Management

Allow users to quickly troubleshoot problems and monitor power use for better operation. When overloaded, some PoE ports will auto power-off until system power is falls below the threshold for system protection.

Integration with Genetec™ Security Center

VIVOTEK NVR’s are not only fully integrated with our own VMS software – VAST 2, now they are also able to connect with Genetec™ Security Center via ONVIF, offering various functions including NVR search & add, video/audio display, video streaming configuration, edge playback, and NVR firmware upgrades. With the connection to Genetec™ Security Center, reliable video surveillance solutions can be delivered to address small, medium, and large surveillance implementations.

Customer Support

Customer support allows VIVOTEK technical support to rapidly debug your NVR, users only need to export logs by pressing one key and providing the logs to the technical support team to get customer support.
In addition, you can get an access ID while connected to the internet. By keeping the remote access button on and providing the access ID to the technical support team, we can remote access your NVR to analyze the cause of errors and then debug it.

Better Video Quality with Lower Bandwidth

With H.265 standard and VIVOTEK’s Smart Stream technology, VIVOTEK NVR is not only able to provide the high quality video, also save the usage of network bandwidth and recording capacity more than regular H.264 standard.

4K IP Camera Video Input and 4K Local Video Output

Supporting 4K IP camera video input and 4K local video output, VIVOTEK’s NVR can provide users extra high definition video resolution ensuring they will never miss a single detail in both video monitoring and recording.

VIVOCloud App & Portal for 24/7 Viewing

The free VIVOCloud app makes surveillance lightweight and portable, ensuring efficient operation. The latest P2P technology makes remote access even more convenient, by simply scanning the QR-code and installing the app, users can view live streams and play recorded clips with the intuitive interface anytime, anywhere. Armed with the Push Notification function, users will directly get an alert message on their Android/iOS mobile device and directly playback the video to check for any suspicious activity.

Vivotek NVR Linux based user guide

Read Also : Vivotek firmware DVR NVR IPC Software download

.

What information of the ND/NV-Series NVR should I provide to contact technical support for help?

Please provide the following information while contacting technical support for help:

2.Problem description.
3.Snapshots or video clips to show the problem.
4.Date and time when the problem happened.
5.NVR configuration file with the password of the admin account.
How to get the configuration file of the ND/NV-Series NVR(Linux-based)?
6.Logs.(Debug log/Archive log/System log/Recording log/User log/Error log)
How to collect logs for Linux-based NVR and provide to VIVOTEK support team?
7.Information of the added camera.(Model name/MAC address/Firmware version)
8.Enable remote access.(If VIVOTEK support engineer needs to connect NVR)
How to export debug logs and enable remote access function from ND/NV-Series NVR(Linux-based)?

We might need the following information, but they are not compulsory:

1.Public IP (with port if any).
2.Port forwarding for FTP port(port 21),SSH port(22), telnet port (port 23).
3.Reproducing steps/ history.
4.HDD model name and storage capacity.

[Linux-based NVRs] How to upgrade the ND-series NVR?

Enhancing the functionality and security of your ND/NV-Series NVR is crucial, and firmware upgrades play a pivotal role in this process. Please follow the steps below to upgrade the ND/NV-Series NVR:

Before starting the upgrade, it’s recommended to back up your current settings and data to prevent any potential loss.

Step 1. Search for your NVR model on the VIVOTEK official website: https://www.vivotek.com/.

001.png

Step 2. Click on the webpage of your specific NVR model.

Step 3. Select ‘Downloads’ to find and download the latest firmware version (for example, ND9425P, as shown in the picture).

mceclip0.png

Step 4. After downloading, unzip the file to find a .img file.

Step 5. To update the firmware, access the NVR and import the .img file via Settings > System > Maintenance > Update Firmware.

mceclip1.png

There are two ways to access the NVR: via a Web console or a Local console. Please choose the appropriate method for accessing your NVR.

Web console

Navigate to Settings > System > Maintenance > Update Firmware and follow the previously mentioned steps.

mceclip0.png

Local console

Firstly, place the .img file on a USB drive and insert it into the NVR.

USB.PNG

Then, access the system settings by clicking on the gear icon in the local view.

mceclip3.png

Once in the ‘Settings’ interface, go to System > Maintenance > Update firmware and proceed as described earlier.  

How to export debug logs and enable remote access function from ND-Series NVR(Linux-based)?

Starts from firmware version v4.1 of ND/NV-Series NVR, VIVOTEK add remote access function on the customer support page.

Please follow the step below to export debug logs and enable remote access* function to get access ID:

There are two ways to access the NVR, please choose which one you access to NVR. 

Web console.

Local console.

Note 1:
1.Remember to provide MAC address of ND-Series NVR at the same time when providing the access ID.
2. Remote access has 14 days validity.

 

Note 2:
* Important Notice *
The ND9213P, ND9323P and ND9425P NVR remote access service for customer support will be temporarily stopped starting from Feb. 7th, 2022 until the middle of April, 2022 due to service maintenance and firmware tunning. After the proper changes have been done in the cloud platform and the firmware, VIVOTEK will release an statement informing the new NVR firmware v4.1 release and will resume the remote services for those specific models.
For ND9441. ND9541, ND9441P, ND9541P, ND9322P, ND9424P, ND9322P-v2 and ND9424P-v2, remote cloud service will NOT be supported. 

 

Web console.

• Go to setting>System>Customer support page
(A). Export debug logs.
(B). Enable remote access.(OFF->ON)
(C). Cope Access ID.
mceclip0.png
Access_1.PNG


Local console.

• Go to setting>System>Customer support page
(A). Export debug logs.
(B). Enable remote access.(OFF->ON)
(C). Cope Access ID.
mceclip3.png
Access2.PNG

How to export the backup/configuration file of the ND/NV-Series NVR(Linux-based)?

The NVR backup file contains the device configuration files, usually this file is exported as a security measure in case the device needs to be reset to defaults and then be restored with a predetermined configuration or previous configuration. This file can also be used by VIVOTEK Technical Support in case they require to reproduce an issue (using the same configuration parameters). In order to export the backup file of the ND/NV-Series NVR please follow the next guide:

Chose your interface:
There are two ways to access the NVR, please choose which one you access to NVR. 

Note: If you are planning to provide the configuration file to Technical Support for analysis/troubleshooting please remember to provide the password of the admin account as well.
.

Web console:

Step 1. Using a browser, access the NVR using the username and password.

mceclip0.png

Step 2. Click on the gear icon to access the NVR configuration page.

mceclip1.png

Step 3. Click on the “System” tab and select “Maintenance”.

mceclip2.png

Step 4. In the “Maintenance” interface click on the “Backup” button to export the backup/configuration file of the NVR. 

mceclip3.png

Step 5.When the download promp appears, click on “Save” to save the backup file to the computer.

mceclip4.png

Step 6.Be sure that the file was correctly stored.

 

mceclip5.png

.

Local console:

Step 1. Prepare and insert the USB into the NVR USB port. You can use either the back panel USB and frontal panel USB ports (if any) to extract the files. 

USB.PNG

Step 2. In the Live View interface, click on the gear icon to access the device configuration page. 
mceclip3.png

Step 3. Go to the system tab, select the maintenance section and click on the “Backup” button to copy the configuration file in the USB. 
mceclip1.png

How to know the MAC address, model name, firmware version and device pack version of the ND/NV-Series NVR(Linux-based)?

Please follow the steps below to check the MAC address, model name, firmware version, and device pack version of the ND/NV-Series NVR:

 

There are two ways to access the NVR, please choose which one you access to NVR. 

Web console.

Local console.

 

Web console.

1.MAC Address:
Please open the Shepherd on your PC to find the MAC address of NVR.
(Refer to How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?)
shepherd.PNGMAC.PNG
2.Model name, Firmware version and Device pack version:
Go to setting>Information>Information

mceclip0.png
mceclip2.png

.

 

Local console.

1.MAC Address:
Please find the MAC label on the top of cover or bottom cover of ND/NV-Series NVR.
If there are 2 MACs on the MAC label, please provide us 2 MACs.
mceclip1.png
2.Model name, Firmware version and Device pack version:
Go to setting>Information>Information
mceclip3.png
mceclip4.png

How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?

Question

How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?

 

Answer

.

]]> https://www.xvraid.com/guide/vivotek-nvr-linux-based-user-guide.html/feed 0 How to get camera list with camera model name, firmware version and MAC addresses via Shepherd? nonadult Hiseeu XMEYE DVR ADVANCED GUIDE https://www.xvraid.com/general/hiseeu-xmeye-dvr-security-system-advanced-guide.html https://www.xvraid.com/general/hiseeu-xmeye-dvr-security-system-advanced-guide.html#respond Wed, 04 Oct 2023 14:59:07 +0000 https://www.xvraid.com/?p=3014 Hiseeu XMEYE DVR SECURITY SYSTEM ADVANCED GUIDE,XMEye is video monitoring software for IPC and DVR. With cloud technology, easy log in by the device’s serial number to show the live view monitoring video to phone and do operation accordingly.

Support log in with cloud technology

Support real time live view

Support remote playback

Local recording and play

Support snapshot and pictures searching

Support bidirectional talk

Support PTZ control

Support scanning serial number by QR code

Support cloud user register and modify

Support remote device add, edit and delete

Support local device add, edit and delete

Support adding device by address

Support manually searching device in LAN

Support version updating automatically

Support searching device function by shake

Why can’t live view the videos on mobile APP or PC Client VMS

1.Please make sure that your DVR system is already connected to the router through ethernet cable successfully

2.Please go to Main Menu > System > Net Service to check the network is connected or not, Cloud should shows: connected 

undefined

3.Make sure the way you add device to your mobile app or PC client with correct serial number and password

Serial number: “Main Menu–Advanced–Version”

undefined

Password: DVR login password 

undefined

Hiseeu XMEYE DVR SECURITY SYSTEM ADVANCED GUIDE

Read More : XMEYE DVR User Manual

What should I do If I forgot my DVR password

1.Right click mouse from home screen, Click “Log Out–>Log Out”

undefined

2.Then click “Forget password” ＞ “Forget answer ” ＞ Then you will see two “QR code” on the monitor

undefined

undefined

undefined

3.Open your Mobile APP “XMEye Pro” , 

(1). Click the “+” icon on the top right corner—>Hit “NVR”

(2). Click “Forgot your device password”–> Scan the QR code (CAPTCHA on the TV monitor)

(3). Scan the QR code shown on your TV monitor. You will get the verification code.

(4). Input the code in “CAPTCHA”

undefined

Add device to mobile APP (XMeye Pro)

As for how to add the device to mobile APP(XMeye Pro), please follow the below instructions

–>1. Please connect the NVR box to your Router via Network Cable;

–>2. Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR is online (Please skip step3), 

.

undefined

–>3. If the cloud status shows “Probing DNS”, Please Navigate to Main Menu > Network > Check Enable DHCP–>Apply;

–>Reboot DVR by unplug power adapter and re plug it, then double-check the cloud status. 

.

undefined

–>4. Go to your TV Monitor, navigate to Main Menu–>Advanced–>Version–> You will see the serial number. 

The QR code contains serial number info. 

.

undefined

–>5. Open the mobile APP “XMeye Pro” and register an account by your email

–>6. Click”+” to add device–>Choose “NVR”

Click the “Scan” icon to Scan NVR’s QR Code. (QR code contains username and password)

No need to input the user name and password manually.

And click “Ok”, and go back to the Device page on App,and you will see the device shows status: online ,

.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p36.png?v=1689673844

Note1:

We do not suggest customers to manually input the serial number, If they input it, the user name and password need to be input, If they scan the code, they don’t have to input the user name and password, So we need to guide them to scan the QR code first, in some situations if we really need the information of the user name and password, and for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p37.png?v=1689674015

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p38.png?v=1689674067

Note 2:

If device shows “offline”, there could be two causes:

(1) DVR is not connected to network successfully, plz go back to Monitor UI Interface to check if the cloud status shows connected or not in the path of “Main Menu > Network > Net Service”

(2) The way he adds the device to the app is wrong, especially some customers don’t know how to find out the QR Code and input the wrong user name and password

Enable the APP push notification on mobile app “XMEye Pro”

1.Please right-click mouse and navigate to Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK” (Default Setting is for Channel 1, Please select “All” channels.)

undefined

2.Open “XMeye Pro” mobile App, and navigate to Event–>Device (the one you named)–>Enable “Allow Notifications”

undefined

undefined

Camera stay in Black’n white during the daytime

It’s a normal situation especially during the switch from night to day, but if the camera keep stayiing in the black and white mode for a long time in the daytime, plz unplug the camera from the DVR port, and replug the wire of the camera into the DVR port to have a try first. 

After repluging the wire of the camera, and if the situation happens again, plz contact us for further support

Add device on PC Client(VMS)

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=  

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=  

.

1. Download PC Client “VMS” and installed

[ Need to drag the file to the desktop after installing firmware, or it would ocurred the issue of “unable to open archive file”]

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

undefined

3. Navigate to “Device Manager”–>”Manual Add”

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p32.png?v=1689673321

4. Login Type: Cloud ID

Device Name: Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

[Note: most customers do not know how to find the serial number, so they can’t add the device to PC Client

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p33.png?v=1689673437

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

[Note: Most customers do not know their user name and password, so we need to guide them to go next to the TV monitor, and right click the mouse from “Log out–Log out”, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p34.png?v=1689673510

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p35.png?v=1689673576

What if the APP keeps asking the user and password?

Step: Plz input the Monitor UI user name and password to resolve this issue

The cause： Sometimes the APP would be in the process of auto-maintain, so it would ask for the user name and password to protect the account’s safety. This page will pop up when you want to live to view the camera.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p28.png?v=1689672924

Note: Some customers enter the App account user name and password. Actually, it’s the Monitor UI user name and password      

As for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu“, this interface [system login] will pop up, and here are the user name and password we need to enter into the app

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p29.png?v=1689673007

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p30.png?v=1689673042

.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p31.png?v=1689673057

Upgrade NVR/DVR firmware

If customers need a firmware upgrade for NVR/DVR, and we need the “System version” to send to XMmanufacturer to ask for a firmaware to upgrade  

Go to Monitor UI Interface, and navigate to “Main Menu– Advanced–Version“

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p25.png?v=1689672707

After get the Version:

Please follow the instructions below to upgrade the NVR/DVR firmware. Steps:

Attached new firmware for you, please download it and unzip it.  

1. Copy to your USB flash drive, and put it in the root directory(Do not under any folder)

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p26.png?v=1689672763

2. Plug the USB device into NVR/DVR

3. Navigate to “Main Menu–> Advanced–> Upgrade”

> Upgrade position(Select your usb device)

–> Upgrade file (Select the firmware)

–> Upgrade

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p27.png?v=1689672837

Unable to open VMS archive file

Please drag the exe file to your Desktop interface (do not under any folder) and run it again.

Like it the photo shows , plz do have a try again ,the VMS will run normally

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p24.png?v=1689672625

One or two cameras are not wokring

(1) BNC Cable connected to Camera is broken

Step: Use another BNC cable to connect the camera to have a try

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p22.png?v=1689672465

(2) The port of the DVR box is broken

Step: After changing the BNC cable, and still there is no camera image, plz insert the camera into another port of the DVR to have a try

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p23.png?v=1689672512

(3) Camera is broken after troubleshooting with the steps （1）–（2）

Network “Probing DNS”?

1. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p20.png?v=1689672327

–>2. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply; –>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p21.png?v=1689672381

How to Sign Up APP Account

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p8.png?v=1689670489

[Note: You can tap on “Local” for quick login without registration. (In this situation, you still can have live view and playback but are not able to receive motion detect alarm message), so mostly we suggest customers to sign up an account first]

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p9.png?v=1689670618

My UI Interface stuck in Hiseeu Logo

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p16.png?v=1689671876

We need to upgrade the system to solve this problem, and check customer’s NVR mainboard info first, and take a photo for us to make sure about firmware verison, then we will ask manufacturer to send us a firmware to upgrade the system to solve this problem

1. If you are in the phone call , just let the customer take a photo of the mainboard, and send it to email  We will ask for a firmware to solve this problem during our working time

(Different versions have various firmware, there is no standard firmware to upgrade the system, so we need to ask the original manufacturer to do that)

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p17.png?v=1689671986

2. If you are dealing with the email:

Try with the steps:

1. Ask the customer to open the DVR box by using the screwdriver, and take a photo of this mainboard, and make sure the QR Code is clear enough for us to scan

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p18.png?v=1689672101

2.After receiving the photo of the mainboard,  we will ask the XM Manufacturer for a firmware, and upgrade the NVR with the new firmware.    

Upgrade steps

Attached upgrade firmware is for your reference, please download and unzip it first.

1. Copy these 2 files to your USB flash drive, the root directory(Do not under any folder, see the picture attached)

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p19.png?v=1689672176

2. Power off the DVR and insert the USB device

3. Power on the DVR, it will upgrade automatically. Please give it a try and let us know the outcome.

My UI Interface shows “No signal” or “Black Screen”

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p11.png?v=1689671374

We need to divert this issue into two situations:

1. DVR Indicator light is on:

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p12.png?v=1689671440

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur. Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

  (2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having the issue, and needs a replacement, plz contact email for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

After the steps, if the thing still can’t be resolved, which means the DVR box is broken, plz contact email for a replacement DVR box if their warranty is still 1 year, and if the warranty is over 1 year, plz leave us a five-star review for us to apply for a free DVR box

.

2.DVR Indicator light is off:

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p13.png?v=1689671613

(1) Cause: The power adapter 12V 2A connected to DVR box is broken

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p14.png?v=1689671678

Step: Use another power supply 12v 2A to power on the DVR unit to have a try

( If you do not have a spare one, use the one that is connected to 4 cameras to have a try)

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p15.png?v=1689671738

(2) Cause: The hard disk drive inside of the DVR box is broken Step: Use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

After the steps, if the thing still can’t be resolved, which means the DVR box is broken, plz contact email for a replacement DVR box if their warranty is still 1 year, and if the warranty is over 1 year, plz leave us a five-star review for us to apply for a free DVR box

How to Share the APP to other

1.Open the “Xmeye Pro ” app ,Click the pencil to edit,

Then Click the Share

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p5.png?v=1689670221

.

2.Select the function which you want to share

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p6.png?v=1689670273

.

3.Finally enter the user name who you want to share ,then you can shre to others successful.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p10.png?v=1689671026

How to reset XMEye Pro Password?

1. Click on “Forget Password”

2. Input your number or Select “Email”(Depends on the method you signed up before)

3. Input your email address and click on “Get Code”

4. A code will be sent to your email, input the verification code here and click on “Next” to continue.

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p4.png?v=1689670117

How to Flip the Camera

1. select the channel of the flip camera

2. Navigate to “Main Meun“–> “XVI control“

3. check the”Overturn

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/p3.png?v=1689670007

How to find out the “Cloud ID” (Serial Number) when adding device to PC Client “VMS”?

The “Cloud ID” is “serial Number”on the NVR UI Monitor Interface

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/11_b6c20a07-04f9-4b0d-b0d4-7c88cf3df45a.png?v=1689669578

Go to your TV Monitor that is connected to NVR, Navigate to “Main Menu–>Advanced–>Version“–> You will see the Serial Number

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/110.png?v=1689669661

https://cdn.shopify.com/s/files/1/0581/4521/0500/files/110_b2c44b35-0827-441f-9a04-deaabde56716.png?v=1689669718

Why the DVR can’t record or playback video

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

1. Check if the hard drive status is normal or error

Navigate to: Main Menu–>Advanced–>HDD info. 

 If it’s hows “error” or no hard drive info, means hard drive failure. (need to replace hard dirve)

undefined

2. Check the record plan is set up for 24/7 continues recording

Navigate to Main Menu–>Record Conf

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

undefined

3.   Please make sure the HDD was set up to “Overwrite”

Navigate to Main Menu–>General–>Storage Full

undefined

Any ideas, let us know. Thank you for your cooperation. 

.

]]> https://www.xvraid.com/general/hiseeu-xmeye-dvr-security-system-advanced-guide.html/feed 0 RXCamView XVR User Manual https://www.xvraid.com/general/rxcamview-xvr-user-manual.html https://www.xvraid.com/general/rxcamview-xvr-user-manual.html#respond Thu, 21 Sep 2023 15:14:17 +0000 https://www.xvraid.com/?p=2878 The RXCamView app is designed to work with NVR, DVR, IPC and other surveillance camera.
With the video preview feature of this app, you can remotely view real-time surveillance video anytime, anywhere;

With the video playback feature, you can conveniently view what happened in the past period. Work with a surveillance camera which supports AI, you can even search video records from a large number of videos by a face photo;

Of course, with the alarm message service, you can receive the alarm information of the places you care about in the first place, so as to take timely measures to reduce your losses;
With the voice intercom feature, you can also communicate with the people where the camera is located

Key features:
1. Watch HD video in real time
2. Historical video viewing
3. Event message reminder
4. Call through two-way audio
5. Get instant alerts when motion, human form, sound are detected
6. Customize detection area and sensitivity
7. Set recording schedule and alarm notification schedule

RXCamView XVR User Manual

Reset password for DVR system

Firstly, please provide mac address to me (See below pictures) ,and I will use it to create a super password to you .

http://www.tontonsecurity.com/UploadFile/image/20210715/20210715112045_93353.jpg

.

.

http://www.tontonsecurity.com/UploadFile/image/20210715/20210715112122_18957.jpg

.

Secondly ,please enter your system >Multi-user,and click User Edit on the right (generally only the first line No.1 is enabled), then you can modify the user name and set a new password .

.

http://www.tontonsecurity.com/UploadFile/image/20210715/20210715112820_95702.jpg

.

.

http://www.tontonsecurity.com/UploadFile/image/20210715/20210715112843_79382.jpg

.

RXCamView XVR User Manual

Read More : GW Security XVR NVR Firmware Software Download

How to connect the device to the mobile app

.

.

1. Please connect DVR system to the Internet:

.

   a) Please connect the system to a router via LAN cable first

    b) Please DO NOT tick “Enable” of the IP FILTER in the Network page, see below pic

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615154241_60969.jpg

.

    3)Please check the system if it is connected to the Internet successfully. If yes, you can add the device to the mobile app.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615154545_90940.jpg

.

2.Open the app, if it is the first time use, directly click the “+” icon in the upper right corner of the”Device Manager” interface; if it is not the first time, click the icon http://www.tontonsecurity.com/UploadFile/image/20210615/20210615154502_53033.jpg in the upper left corner,then select “Device List” to enter the “Device Manager” Interface, and then click the “+” icon in the upper right corner.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615154726_81066.jpghttp://www.tontonsecurity.com/UploadFile/image/20210615/20210615154814_77376.jpghttp://www.tontonsecurity.com/UploadFile/image/20210615/20210615154821_88570.jpg

.

3.Scan the P2P ID QR code on the DVR / NVR to add the device. (Alternatively, it can be added through “Online Search” and “Manual Add”, the method is omitted).

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615155751_64449.jpg

.

4.This step is more important:

.

a) The “Media Port” must be the same as the “Client” port on the DVR / NVR (If the user’s DVR /NVR has not been modified, the default value is 9000. If the user has modified the “Client” port on the DVR / NVR, (The “Media Port” on the APP needs to be modified synchronously).

b) “User Name” fill in the user name set during the first use. If you are not sure, you can click”Setup”-“System”-“Multi-User” to view.

c) “Password” fill in the password set during the first use, which is the login password of the user DVR / NVR.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615155955_78465.jpghttp://www.tontonsecurity.com/UploadFile/image/20210615/20210615160000_12275.jpg

.

5.After the setting is completed, click “Save”, then the APP will display the added device, and”Connection Status” prompts “Connected” to indicate that the DVR / NVR is connected. Click the icon http://www.tontonsecurity.com/UploadFile/image/20210615/20210615160152_27800.jpg to play the video. Click on the icon http://www.tontonsecurity.com/UploadFile/image/20210615/20210615160158_36754.jpg to select 1/4/8/16 picture viewing.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615160243_40423.jpghttp://www.tontonsecurity.com/UploadFile/image/20210615/20210615160248_13577.jpghttp://www.tontonsecurity.com/UploadFile/image/20210615/20210615160253_43433.jpg

.

How to upgrade your NVR or DVR

NVR Upgrade

.

1. Copy the firmware file(.sw file)to your USB drive, and insert the USB flash drive into the NVR’s USB port.

http://www.tontonsecurity.com/UploadFile/image/20210128/20210128141633_34749.jpg

http://www.tontonsecurity.com/UploadFile/image/20210128/20210128141706_23241.jpg

2. Click Select File button to choose the firmware file in your USB flash drive, then Click OK.(Setup-System-Maintenance-Upgrade)

http://www.tontonsecurity.com/UploadFile/image/20210128/20210128141751_61119.jpg

3. Click Upgrade button to start system upgrade. The system upgrade will last around 5-10 minutes, please do NOT power off the NVR or remove the USB from NVR during firmware upgrade.
http://www.tontonsecurity.com/UploadFile/image/20210128/20210128141827_74173.jpg

.

Add IP camera (1319 1329 8204 8208) to DVR (D3505)

ADD IPCAMERA

.

Before you start:

.

1.The DVR supports to disable analog channels to increase IP channels. If you want to disable an analog channel, uncheck the box and click Apply to save. To disable an analog channel can increase an IP channel input. To do so, you need to enable the XVR mode in advance at System→General→Mode.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615161227_18176.jpg

.

2.Ensure the network connection is valid and correct, and Make sure your IP Camera and DVR are on the same network during setup.

.

Steps:

.

1.If you enable the XVR mode for the DVR, it supports to add IP cameras & modify IP channels.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615161448_89611.jpg

.

2.Click Search to search IP cameras from local network, click Add to add individual IP camera, click Add All to add all IP cameras.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615161543_18028.jpg

.

3.Click Search button to search IP cameras, and then click one of the IP camera in the
device list.

       IP Address/Domain: IP address or domain name of the IP camera
       Alias: Name of the IP camera
       Position: Position to display the camera name on the screen.
       Port: Port of the IP camera

       Protocol: Choose the protocol of the IP camera from the dropdown menu
       User Name: User Name of the IP camera
       Password: Password of the IP camera
       Bind channel: Choose a channel of the DVR you want to attach to
       Auto Assign IP to Camera(s): The added IP camera would be not able to connect if its IP address is not in the same network segment with DVR. With this function to reassign an IP address to all added IP cameras.
       Channel Delete: Choose one or more added IP cameras, and click this button to Detele.

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615161927_76466.jpg

.

How to add IPC to DVR via Onvif

How to add IPC to DVR via Onvif

.

1.Power on the DVR, connect the IPC, and enter the password to log in to the following interface:

 

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615141230_33920.jpg

.

2.Please click Channel to enter the following interface:

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615141336_73940.jpg
.

.

3.Click Search to search for IP, then check the IP to be added, and click Add:

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615141419_50332.jpg
.

.

4. The following interface appears, change the Port port to 80, select Onvif for the procotol protocol, and confirm that the user name and password are correct:

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615141507_37145.jpg
.

.

5. Close the page to see that the IPC is online:

.

http://www.tontonsecurity.com/UploadFile/image/20210615/20210615141557_45349.jpg

How to add device to surveillance client

How to add device to surveillance client              Click here to download

.

]]> https://www.xvraid.com/general/rxcamview-xvr-user-manual.html/feed 0 How to reset the password of SAFIRE devices https://www.xvraid.com/guide/how-to-reset-the-password-of-safire-devices.html https://www.xvraid.com/guide/how-to-reset-the-password-of-safire-devices.html#respond Thu, 18 May 2023 18:33:57 +0000 https://www.xvraid.com/?p=1371 How to reset the password of SAFIRE devices, There are two procedures to recover the password of Safire recorders, and each procedure depends on the system of the HTVR, DVR, NVR or camera you want to recover. In both cases the SADP software is used.

1- Install the SADP from the manufacturer’s website:

https://athena-visiotech.s3-eu-west-1.amazonaws.com/d1XvP3EBNOqssiu8J01D/Safire_SADPTool_v3.0.2.50build20200402.zip

2- Run the device finder, which will find the devices by MAC address.

3- Select the device to be recovered and click on the Forgot Password button (bottom right button)

?name=inline 1774174411​

If the software indicates to export a file, follow the procedure from step 4 to 7, while if the software indicates to enter a Security Code follow the procedure from step 8 to 12.

Procedure 1:

4- We are asked to export a file (Export File). Click on the Export button, and select the path where the file is to be saved; confirm.

?name=inline 716268710​

5- El fichero se descargará al Pc. A continuación envíe un correo al nuestro servicio técnico para que se lo mandemos al fabricante y genere el fichero de recuperación de contraseña: no apague el grabador en ningún momento desde el momento de generar el fichero hasta que se lo devolvamos.

?name=inline1015703687​

6- After importing in the same tab the recovery file, enter the new password for the recorder and repeat it. The password must be identical in both boxes (New Password and Confirm Password), otherwise, it will not allow you to continue.

7- Confirm the import and wait for the file to load. If you have done the procedure correctly, a window will appear with the following text: Your recorder’s password has now been reset.

Procedure 2:

8- You are asked to enter a Security Code9-

Press the Cancel button, and go back to the SADP, you have to take the Serial number and the Start time, and send them to our technical service

How to reset the password of SAFIRE devices

Read Next :

This can be achieved in two ways:

a. Go, within the SADP list, to the device from which you want to retrieve the password and look at the data in columns 4 and 5.

b. Click directly on the Export button, to generate the Excel file to be sent to us (to avoid errors when entering the data)

?name=inline249027838

10- Safire will send us some security codes, go to step 3, then step 8 and enter the code according to the date you are in.

We remind you that the correct code for the date (Today) will return the equipment to the factory password, which is “12345”

EXAMPLE

If you request the codes, for example for the 7th of October and you are only going to have access to the equipment on the 9th, you have to use the code corresponding to the 9th of October. It is important that the recorder is not restarted until the password is reset.

The password will be the factory default (User: admin / Password: 12345).

IMPORTANT: When sending the file or the required data, the device cannot be turned off under any circumstances, otherwise the procedure would have to be redone

User and password of the cameras that come pre-activated in SAFIRE

On Safire cameras that come activated and with a password, the user is admin and the password is admin+verification code.

The verification code is located on the sticker on the camera itself.

Below is a list of the products that have this feature:

  • SF-IPCV037AH-4W
  • SF-IPDM820AH-4W
  • SF-IPB025HA-2E
  • SF-IPB025HG-2E
  • SF-IPB025WHG-4P

*this list is for indicative purposes only, and subject to change

Reset of Safire cameras SF-IPSD4704IHA-4P and SF-IPSD4704IHA-4PW

Resetting these two cameras requires the pressure of a physical button.

This reset button is found by opening the base of each device:

 

mceclip0.png

mceclip1.png

Safire – How to recover password by email or recovery questions

To recover the password:

 

1. Open SADP Tool2

. Click on “Forgot Password”

 

?name=inline338602627

3. Use the questions or the email option

4. If the email option is chosen

Save the QR and send the QR to the email address pw_recovery@device-service.com as an attachment. (Or use the XML code)

In general, when using automated email services, you will get a retrieval file within 5 minutes.

Note:

This email address only works when you have registered the email address you registered on the device. See the article: Safire – Prepare for lost passwords

 

mceclip1.png

?name=inline 1723637902

When you have received the email

mceclip3.png

Use the verification code from the email and create a new password

Note:

When deactivating the Safire network cameras that are connected to the NVR for which you have requested password recovery, also select (A) “Reset Network Camera’s Passwords”.

mceclip5.png

 

When not using email or questions on the device

 

Select the secret key export/import mode and send the XML file to your supplier or distributor.

They will process the recovery and get back to you with the key in your mail.

Please note that this is not an automated process and may take time.

 

Note:

The file you receive is valid for a period of 48 hours. You cannot shut down or restart your computer until after you have completed all the steps.

 

?name=inline166396462

3. When you receive the recovery file

3.1 In step 2

A. Select import file

B. Import the XML file from the received e-mail

C. Create a new password

D. Confirm password

mceclip0.png

mceclip6.png

]]> https://www.xvraid.com/guide/how-to-reset-the-password-of-safire-devices.html/feed 0 How to Use Milesight PoE NVR https://www.xvraid.com/guide/how-to-use-milesight-poe-nvr.html https://www.xvraid.com/guide/how-to-use-milesight-poe-nvr.html#respond Thu, 13 Apr 2023 19:17:06 +0000 https://www.xvraid.com/?p=1328 How to Use Milesight PoE NVR For the PoE ports, each port has a fixed number like the above picture showing. They can be directly used to connect to the Milesight cameras.

1. LAN Port and PoE Ports

ZOSGCUB1yuJpdg7pzRRQGOtYqvLrCmUaIA

Intuitively, there is one LAN port and four PoE ports in the MS-N1009-UPT.

For the LAN port, the default IP address is 192.168.5.200. You can set the local IP for the NVR via Smart Tools which you can download from the official website of Milesight. And you can log-in the NVR to manage it via web by using the IP address .

For the PoE ports, each port has a fixed number like the above picture showing. They can be directly used to connect to the Milesight cameras.

2.How to use PoE ports

For MS-N1004-UPC, the default IP address of the 4 PoE channels are 192.168.20.xx. When you activate a NVR, the NVR password will also be used to activate the PoE channels.

when you put the IP camera into the PoE port,

  • 1) It can plug and play as long as its password is same with the NVR.

For example: NVR: 192.168.7.150Password: ms111111

IPC1: 192.168.7.151Password: ms111111

Plug in and refresh.

yVcPBZI0U6M99A5pkImZ31PY7cOGubTUXw

You will find that the IP address has been changed into 192.168.20.xx. And it shows .

1) When the password of the IP camera is not same with the NVR, we can make it connected through editing the exact password of the IP camera.

For example:NVR: 192.168.7.150Password: ms111111

IPC2: 192.168.7.152Password: ms123456

                    Plug in and refresh.

ra6 g0aia2ofcOI6UQuDmaMhaiMkPyEqXQ

The password of the IP camera is not the same as the channel, so status will be shown as NOP8nkhzmOj0JDLYfuViDonIgkZPqbyzjA.

There are two ways to edit password to make the IP camera connected:

l One way:

Choose the tVmp2yZPi CZ0Vsa2o541iyppPmc8JukjA IP camera, and then click on “Edit Authentication”.

 

Milesight PoE NVR

Read Next : Milesight &#8211; How to Upgrade Firmware for IP Camera

After clicking on the button, it will pop up a window as follows. Then input the exact password “ms123456” and click on “OK”.

  • The other way:

Click on the button “Edit”.

After clicking on the button, it will pop up a window as follows. Then input the exact password “123456” and click on “OK”.

After saving the password, the status will be shown as  by clicking on the button “Refresh”.

lPo1GtvkEMfglWO51PVDt7Q6dRlTvW0W3w

3) If the IP camera has ever been connected into the random PoE port , even if its IP address changes after being pulled out , as long as the password dose not change, you can plug in random PoE port without verifying password anymore.

On the contrary, you need to verify the password if you changed the password of the IP camera.

For example:IPC1 :192.168.20.2password: ms111111

Previously it connected in Port1.

Pull out the IPC1 and edit the IP address into 192.168.7.151, but don’t change the password.

vL2OCccLRMyzkxRwNfVVbNXuzTJ J3siwg

Now put it into Port3. Just refresh, then you will find that it has been connected in Port3 without verifying password and the IP address has been changed into 192.168.20.xx.

ROa9ax0S DxKcCvFbj OhZnd IO R4vjtA

Note:

If you have done the right steps, but you find that the state is “Disconnected”. Please keep clicking on the “Refresh” till “Connected” comes out.

3. How to configure IP camera connected via PoE

For the network cameras connected with PoE NVR via PoE ports, you can not view or configure them on web directly because the IP network segments of IP camera and your PC are different. There are two ways to solve this issue.

One way:

1) Connect PC to one of the PoE ports of PoE NVR using a network cable;

BiXlyhWvVapHGa WV6 i8QW51r25LrRH g
Configure camera on web via PoE port

Then you can view and configure both PoE NVR and IP camera directly on web using corresponding IP address.

  • The other way:

1) Enable the “ Channel Access” in Setting and saving.

Note: This setting is disabled by default.

2) Click on the “IE” button.

3) After clicking on the button, it will pop up a window as follows.

4) Input the user name and password,Then you can view and configure IP camera directly on web.

2tHadBYQEsXuf7bery3h01dmHvKUJKda6A

]]> https://www.xvraid.com/guide/how-to-use-milesight-poe-nvr.html/feed 0 Unboxing the Milesight 4K H.265 Mini PoE NVR 1000 Series nonadult Vivotek firmware DVR NVR IPC Software download https://www.xvraid.com/firmware/vivotek-firmware-dvr-nvr-ipc-software-download.html https://www.xvraid.com/firmware/vivotek-firmware-dvr-nvr-ipc-software-download.html#respond Mon, 13 Mar 2023 19:10:06 +0000 https://www.xvraid.com/?p=1302 Vivotek firmware DVR NVR IPC Software download We are with you with our guide where you can find software and firmware files of all devices belonging to Vivotek company . vivotek company is one of the giant brands of the company in the global sense with its DVR NVR IPC AHD TVI XVI and Hybrid devices .

Vivotek firmware DVR NVR IPC Software download

Read Next : How to upgrade vivotek camera?

AB5156

AB5156

Firmware0202a / 2016.03   Datasheet
AB5166

AB5166

Firmware0200e / 2016.09   All Files ➤
AB5353H

AB5353H

Firmware0204c / 2014   Datasheet
AB5376

AB5376

Firmware0101b / 2016.03   Datasheet
AB5376 to

AB5376 to

Firmware0200e / 2016.09   All Files ➤
AB5396

AB5396

Firmware0102a / 2016.03   Datasheet
AB5396 to

AB5396 to

Firmware0200e / 2016.09   All Files ➤
AB6117-HP

AB6117-HP

Firmware0101f / 2016.11   All Files ➤
AB6317-HT

AB6317-HT

Firmware0101f / 2016.11   All Files ➤
the AD5166

the AD5166

Firmware0200e / 2016.09
AD5196

AD5196

Firmware0102a / 2016.03   Datasheet
the AD5196

the AD5196

Firmware0200e / 2016.09   All Files ➤
AF5108

AF5108

Firmware0200b / 2016.11
AF5127

AF5127

Firmware0102b / 2014   Datasheet
AF5147

AF5147

Firmware0102g / 2014
AF5147V

AF5147V

Firmware0200f / 2016.03   Datasheet
AS5336 to

AS5336 to

Firmware0203d / 2016.03   Datasheet
AS6316-EHL

AS6316-EHL

Firmware0101h / 2016.11   All Files ➤
AW-GET-094 A-130

AW-GET-094 A-130

Firmware0106 / 2015.09   All Files ➤
AW-GEV-104 A-130

AW-GEV-104 A-130

Firmware0119 / 2016.09   All Files ➤
AW-GEV-104B-130

AW-GEV-104B-130

Firmware0003 / 2017.09   All Files ➤
AW-GEV-107 A-130

AW-GEV-107 A-130

Firmware0002 / 2017.12   All Files ➤
AW-GEV-184B-250

AW-GEV-184B-250

Firmware0003 / 2017.09   All Files ➤
GEVA-264-AW-185

GEVA-264-AW-185

Firmware0119 / 2016.09   All Files ➤
AW-GEV-264 A-370

AW-GEV-264 A-370

Firmware0119 / 2016.09   All Files ➤
AW-GEV-267 A-370

AW-GEV-267 A-370

Firmware0002 / 2017.12   All Files ➤
AW-GEV-264B-370

AW-GEV-264B-370

Firmware0003 / 2017.09   All Files ➤
BB5116

BB5116

Firmware0107a / 2014   Datasheet
BB5315

BB5315

Firmware0401a / 2015.01   Datasheet
BB5315-C

BB5315-C

Firmware0401a / 2015.01
BD5115

BD5115

Firmware0301c / 2014   Datasheet
BD5336

BD5336

Firmware0200d / 2014   Datasheet
CC8130

CC8130

Firmware0202a / 2016.03   All Files ➤
CC8130 (HS)

CC8130 (HS)

All Files ➤
CC8160

CC8160

Firmware0100e / 2017.11   All Files ➤
CC8160 (HS)

CC8160 (HS)

All Files ➤
CC8370-HVR

CC8370-HVR

Firmware0204j / 2017.11   All Files ➤
CC8371-HVR

CC8371-HVR

Firmware0104j / 2017.11   All Files ➤
Autodesk Revit

Autodesk® Revit®

All Files ➤
Device Pack

Device Pack

5.9.1422017.10  5.9.1302017.08  5.9.1222017.07 All Files ➤
CD8371-HNTV

CD8371-HNTV

Firmware0104j / 2017.11  All Files ➤
CD8371-HNVF2

CD8371-HNVF2

Firmware0104j / 2017.11  All Files ➤
fd61x2v

FD61x2V

Firmware0104c / 2014  Datasheet Guide  Manual
FD7131

FD7131

Firmware0300b / 2014  Datasheet Guide  Manual
FD7132

FD7132

Firmware0301a / 2014  Datasheet Guide  Manual
FD7141

FD7141

Firmware0200a / 2014  Datasheet Guide  Manual
FD8131

FD8131

Firmware0301c / 2014  Datasheet Guide  Manual
FD8131V

FD8131V

Firmware0301c / 2014  Datasheet All Files ➤
FD8133

FD8133

Firmware0300e / 2014  Datasheet Guide  Manual
FD8133V

FD8133V

Firmware0300e / 2014  Datasheet Guide  Manual
FD8134

FD8134

Firmware0301c / 2014  All Files ➤
FD8134-SS

FD8134-SS

Firmware0105b / 2014  All Files ➤
FD816B to-HF2

FD816BA-HF2

Firmware0104j / 2017.11  All Files ➤
FD816B-HT

FD816B-HT

Firmware0101b / 2016.11  All Files ➤
FD816B to-HT

FD816BA-HT

Firmware0104j / 2017.11  All Files ➤
FD8161

FD8161

Firmware0105b / 2014  Datasheet Guide  Manual
FD8162

FD8162

Firmware0104b / 2014  Datasheet Guide  Manual
the FD8166

FD8166A

Firmware0204j / 2017.11  All Files ➤
FD8166-Na

FD8166A-N

Firmware0104j / 2017.11  All Files ➤
the FD8167

FD8167A

Firmware0204j / 2017.11  All Files ➤
FD8167-T

FD8167-T

Firmware0103a / 2016.04  All Files ➤
FD8168

FD8168

Firmware0100e / 2014  All Files ➤
the FD8169

FD8169A

Firmware0204j / 2017.11  All Files ➤
FD816C-HF2

FD816C-HF2

Firmware0100x / 2016.11  All Files ➤
FD816 by-HF2

FD816CA-HF2

Firmware0104j / 2017.11  All Files ➤
FD8177-H

FD8177-H

Firmware0103d / 2017.11  All Files ➤
FD8179-H

FD8179-H

Firmware0103d / 2017.11  All Files ➤
FD8182-F2

FD8182-F2

Firmware0104j / 2017.11  All Files ➤
FD8182-T

FD8182-T

Firmware0104j / 2017.11  All Files ➤
FD8366-V

FD8366-V

Firmware0104j / 2017.11  All Files ➤
FD836B-EHTV

FD836B-EHTV

Firmware0101b / 2016.11  All Files ➤
FD836B to-EHTV

FD836BA-EHTV

Firmware0104j / 2017.11  All Files ➤
FD836B-EHVF2

FD836B-EHVF2

Firmware0101b / 2016.11  All Files ➤
FD836B to-EHVF2

FD836B to-EHVF2

Firmware0104j / 2017.11   All Files ➤
FD836B-HIV

FD836B-HIV

Firmware0101b / 2016.11   All Files ➤
FD836B to-HIV

FD836B to-HIV

Firmware0104j / 2017.11   All Files ➤
FD836B-HVF2

FD836B-HVF2

Firmware0101b / 2016.11   All Files ➤
FD836B to-HVF2

FD836B to-HVF2

Firmware0104j / 2017.11   All Files ➤
FD8361

FD8361

Firmware0205a / 2014   Datasheet  Guide   Manual
FD8361L

FD8361L

Firmware0205a / 2014   Datasheet  Guide   Manual
FD8363

FD8363

Firmware0200d / 2014   All Files ➤
FD8365HV

FD8365HV

Firmware0203c / 2016.09   All Files ➤
FD8365EHV

FD8365EHV

Firmware0203c / 2016.09   All Files ➤
FD8367 A-V

FD8367 A-V

Firmware0204j / 2017.11   All Files ➤
FD8369 A-V

FD8369 A-V

Firmware0204j / 2017.11   All Files ➤
FD8377-HVR

FD8377-HVR

Firmware0103d / 2017.11   All Files ➤
FD8379-HVR

FD8379-HVR

Firmware0103d / 2017.11   All Files ➤
FD8382-TV

FD8382-TV

Firmware0104j / 2017.11   All Files ➤
FD8382-ETV

ETV-FD8382

Firmware0104j / 2017.11   All Files ➤
FD8382-VF2

FD8382-VF2

Firmware0104j / 2017.11   All Files ➤
FD8382-EVF2

FD8382-EVF2

Firmware0104j / 2017.11   All Files ➤
FD9171-HT

FD9171-HT

Firmware0103g / 2017.11   All Files ➤
FD9371-HTV

HIV-FD9371

Firmware0103g / 2017.11   All Files ➤
FD9371-EHTV

FD9371-EHTV

Firmware0103g / 2017.11   All Files ➤
FD9181-HT

FD9181-HT

Firmware0103h / 2017.11   All Files ➤
FD9381-EHTV

FD9381-EHTV

Firmware0103h / 2017.11   All Files ➤
FD9381-HTV

HIV-FD9381

Firmware0103h / 2017.11   All Files ➤
FE8171V

FE8171V

Firmware0101c / 2014   Datasheet  Guide   Manual
FE8172

FE8172

Firmware0102b / 2014  Datasheet Guide  Manual
FE8172V

FE8172V

Firmware0102b / 2014  Datasheet Guide  Manual
FE8174

FE8174

Firmware0200f / 2015.08  All Files ➤
FE8174V

FE8174V

Firmware0200f / 2015.08  All Files ➤
FE8180

FE8180

Firmware0200b / 2016.09  All Files ➤
FE8181

FE8181

Firmware0200h / 2015.08  All Files ➤
FE8181V

FE8181V

Firmware0200h / 2015.08  All Files ➤
FE8182

FE8182

Firmware0204j / 2017.11  All Files ➤
FE8191

FE8191

Firmware0103a / 2016.12  All Files ➤
FE8391-V

FE8391-V

Firmware0103a / 2016.12  All Files ➤
FE9181-H

FE9181-H

Firmware0103h / 2017.11  All Files ➤
FE9381-EHV

FE9381-EHV

Firmware0103h / 2017.11  All Files ➤
FE9182-H

FE9182-H

Firmware0103h / 2017.11  All Files ➤

NEW

FE9382-EHV

FE9382-EHV

Firmware0103h / 2017.11  All Files ➤
IB8168

IB8168

Firmware0100e / 2015.06  All Files ➤
IB8360

IB8360

Firmware0100d / 2017.11 All Files ➤
IB8360-W

IB8360-W

Firmware0100g / 2017.11  All Files ➤
IB8367A

IB8367A

Firmware0204j / 2017.11  All Files ➤
IB8367-R

IB8367-R

Firmware0103a / 2016.07  All Files ➤
IB8367-T

IB8367-T

Firmware0103a / 2016.07  All Files ➤
IB8367-RT

IB8367-RT

Firmware0103a / 2016.07  All Files ➤
IB8369A

IB8369A

Firmware0204j / 2017.11  All Files ➤
IB836BA-EHF3

IB836BA-EHF3

Firmware0104j / 2017.11  All Files ➤
IB836B-EHT

IB836B-EHT

Firmware0101b / 2016.11  All Files ➤
IB836BA-EHT

IB836BA-EHT

Firmware0104j / 2017.11  All Files ➤
IB836BA-HF3

IB836BA-HF3

Firmware0104j / 2017.11  All Files ➤
IB836B-HT

IB836B-HT

Firmware0101b / 2016.11  All Files ➤
IB836BA-HT

IB836BA-HT

Firmware0104j / 2017.11  All Files ➤
IB8377-H

IB8377-H

Firmware0103d / 2017.11  All Files ➤
IB8379-H

IB8379-H

Firmware0103d / 2017.11  All Files ➤
IB8382-EF3

IB8382-EF3

Firmware0104j / 2017.11  All Files ➤
IB8382-ET

IB8382-ET

Firmware0104j / 2017.11  All Files ➤
IB8382-F3

IB8382-F3

Firmware0204j / 2017.11  All Files ➤
IB8382-T

IB8382-T

Firmware0104j / 2017.11  All Files ➤
IB9371-HT

IB9371-HT

Firmware0103g / 2017.11  All Files ➤
IB9371-EHT

IB9371-EHT

Firmware0103g / 2017.11  All Files ➤
IP21x2

IP21x2

Firmware0301d / 2014  Datasheet Guide  Manual
IP3132

IP3132

Firmware0203a / 2014  Datasheet Guide  Manual
IP3133

IP3133

Firmware0201b / 2014  Datasheet Guide  Manual
IP3135

IP3135

Firmware0101c / 2014  Datasheet Guide  Manual
IP3136

IP3136

Firmware0100e / 2014  Datasheet Guide  Manual
IP3137

IP3137

Firmware0101d / 2014  Datasheet Guide  Manual
IP31x1

IP31x1

Firmware0201b / 2014  Datasheet Guide  Manual
IP31x2

IP31x2

Firmware0204a / 2014  Datasheet Guide  Manual
IP61x2

IP61x2

Firmware0105b / 2014  Datasheet Guide  Manual
IP61x4

IP61x4

Firmware0102f / 2014  Datasheet Guide  Manual
IP61x7

IP61x7

Firmware0102a / 2014  Datasheet Guide  Manual
IP7130

IP7130

Firmware0102d / 2014  Datasheet Guide  Manual
IP7131

IP7131

Firmware0200a / 2014  Datasheet Guide  Manual
IP7132

IP7132

Firmware0200a / 2014  Datasheet Guide  Manual
IP7133

IP7133

Firmware0202a / 2014  Datasheet Guide  Manual
IP7134

IP7134

Firmware0202a / 2014  Datasheet Guide  Manual
IP7135

IP7135

Firmware0400a / 2014  Datasheet Guide  Manual
IP7137

IP7137

Firmware0401a / 2014  Datasheet Guide  Manual
IP7138

IP7138

Firmware0300a / 2014  Datasheet Guide  Manual
IP7139

IP7139

Firmware0300a / 2014  Datasheet Guide  Manual
IP7142

IP7142

Firmware0302c / 2014  Datasheet Guide  Manual
IP7151

IP7151

Firmware0200g / 2014  Datasheet Guide  Manual
IP7152

IP7152

Firmware0200c / 2014  Datasheet Guide  Manual
IP7153

IP7153

Firmware0300a / 2014  Datasheet Guide  Manual
IP7154

IP7154

Firmware0300a / 2014  Datasheet Guide  Manual
IP7160

IP7160

Firmware0105a / 2014  All Files ➤
IP7160-SS

IP7160-SS

Firmware0105a / 2014
IP7161

IP7161

Firmware0105a / 2014  Datasheet Guide  Manual
IP7161-SS

IP7161-SS

Firmware0105a / 2014  Datasheet
IP7251

IP7251

Firmware0100f / 2014  Datasheet Guide  Manual
IP7330

IP7330

Firmware0300b / 2014  Datasheet Guide  Manual
IP7361

IP7361

Firmware0201f / 2014  Datasheet Guide  Manual
IP8130W

IP8130W

Firmware0100f / 2018.01  All Files ➤
IP8132

IP8132

Firmware0201a / 2014  Datasheet Guide  Manual
IP8133

IP8133

Firmware0200a / 2014  All Files ➤
IP8133W

IP8133W

Firmware0200a / 2014  All Files ➤
IP8151-SS

IP8151-SS

Firmware0301e / 2014  Datasheet
IP8162-SS

IP8162-SS

Firmware0102a / 2014  Datasheet
IP8162P

IP8162P

Firmware0200d / 2014  All Files ➤
IP8162P-SS

IP8162P-SS

Firmware0200d / 2014  Datasheet
IP8166

IP8166

Firmware0204j / 2017.11  All Files ➤
IP816A-HP

IP816A-HP

Firmware0201b / 2017.08  All Files ➤
IP816A-LPC

IP816A-LPC Kit

Firmware0201b / 2017.08  All Files ➤
IP816A-LPC-v2

IP816A-LPC-v2 Kit

All Files ➤
IP816A-LPC Highway-Street

IP816A-LPC

Firmware0201b / 2017.08  All Files ➤
IP816A-LPC(18mm)

IP816A-LPC(18mm)

Firmware0200c / 2015.08  All Files ➤
IP816A-LPC(40mm)

IP816A-LPC(40mm)

Firmware0200c / 2015.08  All Files ➤
IP8330

IP8330

Firmware0104a / 2014  Datasheet Guide  Manual
IP8332

IP8332

Firmware0401a / 2015.01  Datasheet Guide  Manual
IP8332-C

IP8332-C

Firmware0401a / 2015.01  Datasheet Guide  Manual
IP8332-SS

IP8332-SS

Firmware0110a / 2014  Datasheet
IP8160

IP8160

Firmware0100g / 2017.11  All Files ➤
IP8160-W

IP8160-W

Firmware0100j / 2017.11  All Files ➤
IP8352

IP8352

Firmware0200a / 2014  Datasheet Guide  Manual
IP8355EH

IP8355EH

Firmware0201c / 2014  All Files ➤
IP8361

IP8361

Firmware0100c / 2014  Datasheet Guide  Manual
IP8365H

IP8365H

Firmware0201c / 2014  All Files ➤
IP8365EH

IP8365EH

Firmware0201c / 2014  All Files ➤
IP8371E

IP8371E

Firmware0302a / 2016.04  All Files ➤
IB9381-EHT

IB9381-EHT

Firmware0103h / 2017.11  All Files ➤
IB9381-HT

IB9381-HT

Firmware0103h / 2017.11  All Files ➤
IP9171-HP

IP9171-HP

Firmware0103g / 2017.11  All Files ➤
IP9181-H

IP9181-H

Firmware0103h / 2017.11  All Files ➤
IZ9361-EH

IZ9361-EH

Firmware0103g / 2017.11  All Files ➤
ipvsdt

IPVSDT

Ver. 8.12016.05  All Files ➤
iView is

iViewer App

All Files ➤
IW2

IW2

1.3.0.2
2015.10  All Files ➤
IZ7151

IZ7151

Firmware0101f / 2014  Datasheet Guide  Manual
MA8391-ETV

MA8391-ETV

All Files ➤
MD7530

MD7530

Firmware0101a / 2014  Datasheet Guide  Manual
MD7560

MD7560

Firmware0103a / 2014  Datasheet Guide  Manual
MD8531H

MD8531H

Firmware0201a / 2016.03  All Files ➤
MD8563-EH

MD8563-EH

Firmware0104j / 2017.11  All Files ➤
DEH-MD8563

MD8563-DEH

Firmware0104k / 2018.01  All Files ➤
MD8564-EH

MD8564-EH

Firmware0104j / 2017.11  All Files ➤
MD8565-N

MD8565-N

Firmware0104j / 2017.11  All Files ➤
ND8301

ND8301

Firmware1.9.1.8 / 2015.04  All Files ➤
ND8321

ND8321

Firmware1.2.0.201 / 2016.09  All Files ➤
ND8322P

ND8322P

Firmware2.2.0.102 / 2017.06  Firmware1.3.0.3 / 2015.10 All Files ➤
ND8401

ND8401

Firmware1.9.1.8 / 2015.04  All Files ➤
ND8422P

ND8422P

Firmware2.2.0.102 / 2017.06  Firmware1.3.0.3 / 2015.10 All Files ➤
ND9441

ND9441

Firmware2.2.0.102 / 2017.06  All Files ➤
ND9441P

ND9441P

Firmware2.2.0.102 / 2017.06  All Files ➤
ND9541

ND9541

Firmware2.2.0.102 / 2017.06  All Files ➤
ND9541P

ND9541P

Firmware2.2.0.102 / 2017.06  All Files ➤
NR7401

NR7401

Firmware1.0.751 / 2014  Datasheet Guide  Manual
NR8201

NR8201

Firmware1.0.261 / 2014  Datasheet Guide  Manual
NR8301

NR8301

Firmware1.0.670 / 2014  Datasheet Guide  Manual
NR8401

NR8401

Firmware1.1.0.102 / 2014  All Files ➤
NR9581

NR9581

Firmware1.13.1.10 / 2017.12  All Files ➤
NR9681

NR9681

Firmware1.13.1.10 / 2017.12  All Files ➤
PD8136

PD8136

Firmware0201a / 2014  All Files ➤
pt31x2

PT31x2

Firmware0203c / 2014  Datasheet Guide  Manual
pt31x3

PT31x3

Firmware0101a / 2014  Datasheet Guide  Manual
pt31x4

PT31x4

Firmware0102b / 2014  Datasheet Guide  Manual
pt31x7

PT31x7

Firmware0100h / 2014  Datasheet Guide  Manual
PT7135

PT7135

Firmware0400a / 2014  Datasheet Guide  Manual
PT7137

PT7137

Firmware0500b / 2014  Datasheet Guide  Manual
PT8133

PT8133

Firmware0100g / 2014  Datasheet Guide  Manual
PT8133W

PT8133W

Firmware0100g / 2014  Datasheet Guide  Manual
pz61x2

PZ61x2

Firmware0105e / 2014  Datasheet Guide  Manual
pz61x4

PZ61x4

Firmware0105b / 2014  Datasheet Guide  Manual
PZ7131

PZ7131

Firmware0200a / 2014  Datasheet Guide  Manual
PZ7132

PZ7132

Firmware0200a / 2014  Datasheet Guide  Manual
PZ7151

PZ7151

Firmware0101b / 2014  Datasheet Guide  Manual
PZ7152

PZ7152

Firmware0101b / 2014  Datasheet Guide  Manual
pz71x1

PZ71x1

Firmware0201a / 2014  Datasheet Guide  Manual
pz71x2

PZ71x2

Firmware0201a / 2014  Datasheet Guide  Manual
pz81x1

PZ81x1

Firmware0104a / 2014  All Files ➤
pz81x1w

PZ81x1W

Firmware0104a / 2014  All Files ➤
RX7101

RX7101

Firmware0200a / 2014  Datasheet Guide  Manual
Shepherd

Shepherd

2.3.0.1042017.07  All Files ➤
sd61x2v

SD61x2V

Firmware0101d / 2014  Datasheet Guide  Manual
SD7151

SD7151

Firmware0301b / 2014  Datasheet Guide  Manual
sd73x3

SD73x3

Firmware0103c / 2014  Datasheet Guide  Manual
SD8121-SS

SD8121-SS

Firmware0100g / 2014  Datasheet
sd81x1

SD81x1

Firmware0103c / 2014  Datasheet Guide  Manual
SD8323 A-SS

SD8323E-SS

Firmware0100g / 2014  Datasheet
the SD8362

SD8362E

Firmware0203d / 2014  Datasheet Guide  Manual
SD8362 A-SS

SD8362E-SS

Firmware0102b / 2014   Datasheet
the SD8364

the SD8364

Firmware0200d / 2016.03   All Files ➤
sd83x1 to

sd83x1 to

Firmware0202b / 2014   All Files ➤
sd83x2 to

sd83x2 to

Firmware0202b / 2014   All Files ➤
sd83x3 to

sd83x3 to

Firmware0202b / 2014   All Files ➤
SD9161-H

SD9161-H

Firmware0103g / 2017.11   All Files ➤
SD9361-EHL

SD9361-EHL

Firmware0103g / 2017.11   All Files ➤
SD9362-EH

SD9362-EH

Firmware0103g / 2017.11   All Files ➤
SD9362-EHL

SD9362-EHL

Firmware0103g / 2017.11   All Files ➤
SD9363-EHL

SD9363-EHL

Firmware0103g / 2017.11   All Files ➤
SD9364-EH

SD9364-EH

Firmware0103g / 2017.11   All Files ➤
SD9364-EHL

SD9364-EHL

Firmware0103g / 2017.11   All Files ➤
SD9365-EHL

SD9365-EHL

Firmware0103g / 2017.11   All Files ➤
SD9366-EH

SD9366-EH

Firmware0103g / 2017.11   All Files ➤
SD9366-EHL

SD9366-EHL

Firmware0103g / 2017.11   All Files ➤
SF8172

SF8172

Firmware0100d / 2014   Datasheet  Guide   Manual
SF8172V

SF8172V

Firmware0100d / 2014   Datasheet  Guide   Manual
SF8174

SF8174

Firmware0100c / 2014   All Files ➤
SF8174V

SF8174V

Firmware0100c / 2014   All Files ➤
MS8391-HOUSE

MS8391-HOUSE

Firmware0102c / 2017.08   All Files ➤
MS8392-HOUSE

MS8392-HOUSE

Firmware0102c / 2017.08   All Files ➤
VAST

VAST

1.13.1.1042018.01  1.13.1.102017.10 1.12.5.3012017.07  1.12.5.2012017.04 1.12.5.1012017.01  1.12.1.1022016.09 1.12.1.82016.07  1.11.0.1012016.02 1.10.0.2022015.05  1.9.0.82014.12  1.8.5.32014.08 All Files ➤
VAST 2

VAST 2

2.0.0.57202018.01  All Files ➤
VC8101

VC8101

Firmware0104j / 2017.11  All Files ➤
VC8201

VC8201

Firmware0101a / 2016.04  All Files ➤
vıvocloud

VIVOCloud

All Files ➤
VS2101

VS2101

Firmware0301g / 2014  Datasheet Guide  Manual
VS2402

VS2402

Firmware0301b / 2014  Datasheet Guide  Manual
VS2403

VS2403

Firmware0103e / 2014  Datasheet Guide  Manual
VS3100P

VS3100P

Firmware0203b / 2014   Datasheet  Guide   Manual
VS3102

VS3102

Firmware0201e / 2014   Datasheet  Guide   Manual
VS7100

VS7100

Firmware0301b / 2014   Datasheet  Guide   Manual
VS8100

VS8100

Firmware0102b / 2014   All Files ➤
VS8100-v2

VS8100-v2

Firmware0100e / 2017.11   All Files ➤
VS8102

VS8102

Firmware0300c / 2014   All Files ➤
]]> https://www.xvraid.com/firmware/vivotek-firmware-dvr-nvr-ipc-software-download.html/feed 0 UNV Recorder Set Up Guide https://www.xvraid.com/guide/unv-recorder-set-up-guide.html https://www.xvraid.com/guide/unv-recorder-set-up-guide.html#respond Sun, 05 Mar 2023 19:45:29 +0000 https://www.xvraid.com/?p=1298 UNV Recorder Set Up Guide The NVR can be accessed via phone app (EZView) or by Internet Explorer (http://en.ezcloud.uniview.com). Each user will need to register an account by providing an email address. The first person to scan the code will be the primary account holder, who will then share it with additional accounts as wanted/requested.

UNV Recorder || How to Set Up EZCloud || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

WvtW dpL0AwcgZurL mKkBPVetkwenuktg6Vr78f1A95gFepTxbclZgZhjySbklb

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select System

After selecting System, select the Network option.

0pQKOPDz4HtpBQg3SqGflvVZEcaU8Z7MWofBwDSJX9o4ZluBtXnx0 71wT68LQYigf4 ePqLiHGd8jFhPVpYg8o xFaD0PFt

Under the network tab, make sure that DHCP is enabled (to obtain a network IP address automatically), then select the EZCloud tab.

Ld6qluqF FZr3xd7VSw0bX1rvfLfZIfrn8 LihtiMSk JpttqtdX

On the EZCloud tab, make sure that EZCloud is enabled. Once enabled, the system will be able to be used via P2P

SxFtDHna2GusmU3Gfw0RCppe1gGvdAldJPRIDSINbUsMd4UDzD9cD7K28AS7O0ioxpCvy2XRVAYOt4nFnnjXduQlc9EPUXiw

Note: The NVR can be accessed via phone app (EZView) or by Internet Explorer (http://en.ezcloud.uniview.com). Each user will need to register an account by providing an email address. The first person to scan the code will be the primary account holder, who will then share it with additional accounts as wanted/requested.

UNV Recorder Set Up Guide

Read Next : Uniview Software Firmware Download

Uniview Setup Guide: Video Content Analysis

UNV Recorder || How to Update Firmware on Recorder || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

63BCVgmbzT8hGuOVWYrMx izhx9SgMCt0OIKQn BHh0Tp4VNKSglTOKzjOJcMSSBF8BRq Sk8eFmVxI

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

lYQmkiy9W yozo DOq uVU7 qTWbwmetNX0Mhg2jD8k2F2qTMtRDez2Eg6GMY6IR3 KVLh vBWhCSlOVJo8U2iOecLXyZnxMgsfQ Aqwt1HjZmiZiyhdgbsJo9hSlqzBeyE7iJvg

After logging in, select the “Setup” option.

eVD1ETOLQX 8ek45IJKW9Szi VgiY1qbFvWrxJFWd6dA7W6fGUvxT s9Gq53hKrMJyxamOaNFcZY9QAYgne01G2DTmQRw4dRAFaCOKlFBG7CR x9A5eWw5ZMcTK B3AVIw2BospV

After selecting Setup, select Maintenance

ahpOp TFekGRQOmHFjiiYj9SBCYNLTJ1 WLardr2yAPy0ckJvyQPFTtazq8c9ddgFNkg32 BACKh KhzK8QzDr15NwPLmswlqXQPHDWYa92hUC33nStEPDsa4jon85iYLyN7U9La

After selecting Maintenance, select the Maintenance sub-menu.

ihoLnG5UZbmcJIulvSmWglyegaXFJHqg6HHNQRgEhImEBibteap4aqCTRxloHZEYa5B6w8wBRaXbs99GfqvzWXcZQh

On the Maintenance page, there are two options to do a firmware upgrade: If the system is online, the easiest way to upgrade would be via the cloud option. If the system is not online, please receive the firmware from a technician and upload the file to the NVR via PC and upgrade accordingly.

mhBWAHs2nqxoB3J4gdk4asEEJ0onWw235ClshmLAYO1HGSXos7I1HcOFsQJLQCCS4TgCAethB17CdddYejMYu eZMCr246FniPVOOGJvWHUdl2TtPUaqYN3BhmeCyrm O2czsNbV

UNV Recorder || Factory defaulting the Recorder || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

ZTHSynjGAitv9tf5pLOzVya4kyEQ7D7y 07L CDkDOJCziuguNC 4vzhOg1stfoQnQKoHvi2uk5KjYmEItFIyWGVerZ1FONjMlgp8oncJSsjIW46yf8RrcbJQ9DpxT O2CpBEMPh

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

nyu9VxWNiHK6yYzzvbnc1mKc6TS2 VX qMv3jwhXaMvamzwihZehbXX0j9qts 75 M0MYGf2tbg3QGwMkr4uFFgC2sybpMIQCndGK6EhzBGfrpoN6XMcylALM0s9WyH5EU53vBr

After logging in, select the “Setup” option.

BstcUFCDLcBzM7PufZ9m4gUNmqTzHFPp1p

After selecting Setup, select Maintenance

NKxyJqQLyiumVM

After selecting Maintenance, select the Maintenance sub-menu.

gTjtw TRS5h NIufz3nIetdF7l6UuunySBf0HyJsDhx5D9PBPfQsSwWit3 eVBTySOXysUTwywJ3YJQFEZ6Tw I3Vgpimh0CgCy0TiZLNYIqatQpXWZ1f6i0bv hpmTwfcsiasJC

On the Maintenance page, you will be able to choose the defaulting options. Factory Default will default the system to a brand new state, Default will keep current network settings.

oFnjTG7V5JnnDLxTT05RIwjjH0CFDTvKhm m6cGPcKrx 2ubldmIjDTrhsjHXVS1uCul PdJ06uNCitCR1QKnU39rELsg1rsw47KhNdLBspDiNiD12R6KJhqGs24hHCDoHhv rjw

UNV Recorder || How to Update Firmware on Recorder || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

q3pv9 x3lZYIGU7nj37xN5pUrS4SAvuUi65imVpXvg5ze6 aV2jtiPL4t4rKj9rj3jJeulLvzCGO1Bj4 D 1ah5z ZP4bGGLc0TNCQ7M4ao z35vhQXNXGfeLr5lfIv0 lFyJPcg

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Maintain.

WKMgUKH1hJxOD9CliOx4 0W4nuKND8zZAZGFDTNdj1gLozgVjhiCEjb0c jqoHEa8zIRbhe7oCfoyndQDhSnZBJ2HdtpPo rh4fHriXkPIY3biDfXHQdRnP

On the Maintain menu, please select the Upgrade tab.

sVz2cS5D9fi14cQSg0OECdayUlKg8pLsPSMBfOmyZ6Yn7MMplyNB2 8hNlMN4H1A2 gwLJNlndCW5cU1NX

On the initial Upgrade page, you will be able to locally upgrade the firmware if the file is on hand with a USB drive. If those resources are unavailable, please click the Upgrade by Cloud tab.

On the Upgrade by Cloud page, you will be able to check and see if there are any updates that are available through the internet. After checking and confirming that there is an update, select the Upgrade button after it becomes available. Please note that the cloud function will only work if the NVR is connected to the internet.

GTS9tpxvVhhc2jVB31 SYlyhWTEdzYsRIHxUUkKWXTqE5HdAxQvx6Lain4utTQF7DjfgPQAzRQG8eG27C5eKNqNcjqLJeGRACvrO6YJ aDfdy0Q6N7k0hnCWyA891 372OqXf

UNV Recorder || Configuring Recording Schedule || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

TiwuoAJhvXDOGLFjQGBYj1onpA3DX8Uw1Qc1w8fzecU33RPcKGRL0fXkVfcsAQK0XX6I8lUX86jmZDNj396yWhM5O2 7liTYL6nDDXglpTHEXBVNL6EFOL0QzVuNi8KMAPBLGUpd

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

After logging in, select the “Setup” option.

DKra CmJPADnwoC7QoFLsCMT7Lkg8W3 LzVUYGl5TeTDDc1R7XiW X81KK2Z6jZcVML9t7r64VE77w jeEUvp87R1GwA7M4Ia zUgb1vOjg9m7S03 8Tz86sNIWLpBGlP2zz7wpd

On the Setup page, select Camera on the left hand side menu.

After selecting Camera, select the Schedule sub-menu.

zdvByenNy iDiFfTzi7jYfRjG kqxLi FXUnrdMYURjcqfk3XPZnPGIY1p6B7eSG7oNRlQiQsKBFcdgonHq0zWV7

On the Schedule page, you may click on the record types on the right hand side of the grid. These will be the recording types for each respecting camera. After selecting a recording type, click and drag within the grid area to change the recording type for a specific day and hour.

After setting up a schedule, you may press the down arrow to the right of the “Copy to” checkbox and select all the cameras that will have the same schedule.

UNV Recorder || Configuring Recording Schedules || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

mK1pCsA79EjIiT sggscpgxksRo6wzu52tzvTI2fTUxHrdDgCzYSsxAjmYni8fer0c2jbGDzJETFPKOlioxoDMfniwkKWk5ct2HKqpD hVjEFeTbmb69p6qpX y9iW5CnHdXK aI

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Storage

TvNQjGcur6prXf8IZ apDgWZepKqPxZrJzvG6x2ZffdVXbcFcgsv2s0ffqZqMWO4zQxNZhk dKkYwpZfIu5kozdmD8JO SJjekEar GDn DK otHNQQSREsNX5kQQ3is FOBRk 0

Once on the storage page, it will show the current schedule for camera 1 by default. You may adjust the schedules by selecting the schedule type to the right hand side of the time bar. Please make sure that the schedule is enabled as well.

baQisY5Ya1

You can select the copy button on the bottom of the Storage screen to copy the recording schedule to specific or all cameras.

EMHqvS3ipGCeYOqjE9ksQ9sLFcBFvguq06Zea0if 4Z1TxHJhAFOMyZijTf7O3l9MZ 9pslkl8qY77MSNcQhDNEq9zJYdO014bw9tQUO4qaxDVMqSlgLvcy6Vlp i58JgFYiHlR

You may individually select channels to manually set each one specifically as well.

vq2KkJkI6lhVpDCjtCvOvpZ T5Id87jJ7qF1s8wm hm JiUTn2DPeCT0xI4BoyK uq gGEGQd wgbQP5oXwSrjG4Dj2pojm3hYaNNHkLcBo4oxC NUAipjsFO1Y6F7GY2oKpnnze

UNV Recorder || Configuring Motion Detection || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

NnkZq4hy3g jNPjDe2g6 4gDSFVfWiKhw83CzuQHPqNd0h1yoda6SSBX34uvDQxMLf6oA6etUw xBdBtLAeASiI2Yvjp0ahxxux7O4pmi82 DvJdZ 0juJiI EqgfHh F5YSb v

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

M9HaHX9BtnCCsSUxfY7ckcUM25 zJ5zcEH08ssbuZ1XOaK6S9HBmu ojVwEMv0UaOqDyQAEUiXg 1W iYiMBd2 JNx39

After logging in, select the “Setup” option.

LVBcLijO0yLykrSwYTLGrgIXYbCyR

On the Setup page, select Camera on the left hand side menu.

q 4Cphf6RFbPMjdE5WEAXz2468haFeBI7QYLWnShRy0F43tnbm01dFYyw6b5gQSsBAw4UkyAmUrXy 23rpIRH DVVr

After selecting Camera, select the Motion sub-menu.

olKMrwAelAJxR4Y9uMluQU4ycT2JUpQHc7oDM7g9HjHl kQcOiDs57gaaeGz5Ab1E2YntYpi45 2tvTe4HkV1xRzIyN20oirNcPUCAcPsWftICzYQlFNwNkKTSP LmfhJ9w J A

On the Motion page, you will be able to select individual cameras to create the motion area. Anywhere the red grid is highlighted over will be the motion recording area; you can also enable and disable motion detection on this page. You may change the arming schedule as well as the trigger actions on the respective tabs.

DOaBGMfZe32DvBHi3NByUMTH04UA 55DbJBZa2sprzJnZZ4U F531C6QBJk9 nTaTjD57r QqOaEdE2JiyU4bqhRQ3BD7RASwXFAbmo5HOdrW iqkmQvDM9lym

UNV Recorder || Configuring Motion Detection || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

oKvB9Gv9YomrM2pGkZbun88vP8r7 PcWD9y q7Xkk1xm6kAh3aEBChJJhAfRtlT2rSAaFqgKtlwUE9G5FS3N2piR7bmPQckeXuGs kGRU89AH1eXos0HBBGuYt60WZtoDTf5Eph8

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Alarm.

CnUVPTh9o4BKjJzm3ePAZZ5cWzk h2LNYMJK94v0Qw1IbNCAB1TOa24OVwCBF FL4ea20aTBOghbDMYoMFrRbIyq jIIA5Fdwzyh52EJZ2qDg8NsT6MhnVyQ20ay0HBrR13z5Fq5

On the Alarm menu, you will see the first camera available with motion detection by default. On this page, you can adjust the motion detection area, sensitivity, and other motion related options on this page.

h6fkvEbGAq5Ji XTxd6Sgg1OJ9uzhtfG7tVv5bDHpdbsRvq9irz5JcNl7JT7O8pTlj3hSGy56aczqKoZ3G mnjB91NADPRX8MRAaqnPOIP6eUu5ch7a5e 2un2gT27cDoJN4P63N

You may copy the settings by selecting the Copy button on the bottom of the screen, or you may also select individual cameras to change settings per each camera separately.

NF8KaJEzqFCiTeRGW 9YodnwO9Cvr0We652k44HPzyANu IOISd3ZxL4OzvjsPLXexWzoFc79Az8JDAgmgyTd1lJfX3YyZV4XFskCEm

UNV Recorder || Setting Up Audio and Two Way Talk || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

T6npfS7bksbMBn

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

MWr1Y GCBvNzxW3NKMpW46hsHR74hJY2FSqsuQ94Yp8saijoGNHHbwAbEmC5fnQcpmdSRkqi5BNP

After logging in, the Live View page will be where you will be able to use audio/2-way talk features. If a camera supports 2-way audio, you will see that option.

v5N dgYKbwntNU9ey1nFBu2Wh0Ns9KrQC1X

Another option is using the RCA input and output directly on the back of the recorder to produce 2-way talk audio. This will be on the bottom of the Live View page.

olyExgEwR bAyP0GWCDtwTlKn0mu26GE0SUxI zoK5vow0CGtPSBu iKWGN5Onk9hkbUczVoP8ZckO0c3N1cNUZyovlEwbWQiaqEG4qdyYXYLzADR6ifgVUC78rApuPsLbc1ucYf

UNV Recorder || How to Default an IP Camera || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

BIziMLBphQeTM7Yo PvroD3w5SahMcvPt0PPUPtAuYdPRZElhoVWLhiaT4Eti96CTcOfZZjKMcIb2ZXIex16H0xcWpLyp7ohrlqAVGqZ0LLFhEciAaGEjxqTyufif 5iysehQ lH

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

QxCS1ocQAj04NolGInw6GlQkx9TKjeIBb3KPZuY6MoAlMWIVViSE9WWMySbglQ

After logging in, select the “Setup” option.

0Y IShZsG6u l4naD3CWx44NDWpVSn xQhreMbc9QplGr

On the Setup page, select Camera on the left hand side menu.

pkHLEw hlLs I5HSdjRYt8MAQoMpC1tYAE 4YvjkoUDIMqB9tLYtJDhQh35L15doyU

After selecting Camera, select the Advanced tab on the Camera menu.

pRH DTni1Z dG8Rn82O79qZeJ883b8TQdSJjYyzBHnPDzRR UuoD9FTF9K5yozCAnxDCmxa Qmog plTDnyj5qTWIY1qbjI5PdLqNiHdYR0o qM P1VVjts2YaIhiKcYVKbAYT3

On the Advanced menu, there is an option to see the cameras and default them respectively. You will receive a popup prompt wanting to confirm the default request as well prior to defaulting it completely.

rYgimyk6dlGjASHUDFRvcwJ54AoZQRmKPJq0kzHL4C 3hYwQjsQZZF48lZJno MXYDvFolrr58qg7ytb0L4wrGtRiK9NFeAHkZQ9QBVfUn1LE3RD1GZg0ZO09ecUNqp2kcRSFndB

kNf0e qWxke9rErUSuXv82vgxNCorNqEHL9r53r6m4Tzf79ITt7us0

UNV Recorder || Configuring Email Notifications || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

I8nUq7bSAaM XhisTnSW6nfCPf9pPBQLI gId7viR u311D3QJgPoAF0hbzPl4 Uo9a Ow9eqRh6vFJQ

After logging in, select the “Setup” option.

NGSvbnlVlDOIng97 I1v96ypbnhsakCe8U9Sv8qFO4by1wiiaq Zn9Wlj1qLmczDx8NfAGp7M dnGqp5vFLvNHcCiXO3fErvDk7H2m6TpJvvaL8IKoPDUDSak8GOFMCAPD PkEm

On the setup page, select “Network”.

S MH8JLEB2GYgyZPdiTmMdBg6hN6KQLhNWu P y1vyFWdluaYzh6pUosGMM9HduoQdvE0bybeGZ3A7YJLP Ya TETZB4H ReYlf1LDirpMKfXShZFJG00nbOCRo ZEBcLgWP ikb

After selecting Network, select the Email sub-menu.

Enter the necessary information needed to set up a sender and receiver account. Below is an example of a Gmail account used for email notifications.

1R2Et 7i2zl3Ci IJSEQWIczJEc3MLR3cRtxtVA7v 2k1Wkwghiq9WcmxL

After completing the email page, and successfully testing the email sender and receiver, you may go into any area that would send an email notification. Below is an example of email notifications for motion detection.

NK xQdtiiIKgvR5xKaTCUZioY3U2mvlduh3B1g1doOB8RgFbPw1Hq FQAfQ5cULwsSiGvsMA0ckIIJjB9EazJmOQWO9PLR6WoN8ePQbaSrfF8d cHZpPwAwG0cjgum7Lb426nQsw

If you receive failure messages please log in to the gmail account as the first account and click the link: https://accounts.google.com/b/0/DisplayUnlockCaptcha to unlock the account

UNV Recorder || Configuring Intrusion Detection || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

XaajI0CsAJLPpOy34E8oDocEfPtEaAHjlMylIHbpOgyHRHQReCQFcEuxf Qy1tpfz0AbZCHzuzAPheUnmKt5KJN

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

yL4j fIk76jO5F5oxEiCfzck1czItumDPfSIVSsIebr rzUhDmlHZkeYIUrqiHmYs 3OoWgx43jJYbhtj TGDgerh1h4D5TvLXpcrWF g0q5PfM3

After logging in, select the “Setup” option.

DmXOuqYmaA1byurmWzU5ZdVQvE33IyV8e2Ka94fNRbbzoTXoG0qo0Qo6cUEhFVvp 3rD7FL KuAIoXOjQJjlOyzFGqJIEh5hSETFHsLA4CIWaeZEkQj7yGXloNatmzqS sFpZ1BO

After Selecting Setup, select VCA.

1RqYWY1YuqEjfeuDhmNaqgPZ768rtd7g1H3WqT88qoszhMaDZ6DZGapy3kIaRVQ gIEXZ1yxi 9O4l 49UBOkKWe5CnoPUUSHbM8zeDaABpFSsZKjVZKPTM HTX4vjC8U 4zakfP

After selecting VCA, select the Intrusion Detection sub-menu.

u66 GLp1LgOk28rqm3P7NRG20Arwtw3qiDSs5qXsNnLjr10KXzhBmWSCo9T314Hna1M1eVM1rtMbGHYZOZJl0eZIAF2oxxf8R3Ubmp2BPmqHQc

On the Intrusion Detection Page, select the camera that intrusion detection should be enabled on. Make sure that Intrusion Detection is set for On. Draw the intrusion perimeter and configure the detection area as needed. The primary information needed will be the sensitivity and percentage. Percentage will be the amount of the drawn area that must be filled in order to trigger the intrusion. Select Arming schedule and Trigger actions to indicate when the line cross schedule is active, as well as the commands that it will trigger (record on separate channels, audible alarms, alarm out, email notifications, etc.)

GZAXSsPZxsrCe4i92cGDMwVGy5 ep7fohOrbYgOMjvsvPucVDFltLpux5JCQkQRDI38qFBRFpgIpXEqZvYZmsajALF19EIADObK1kTxvIRELsOJzPoEAGlghi0orxkmz TBEYFlt

UNV Recorder || Finding Recorder Information || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

fXaSSIwhUnO YquXz YZSj9XTXxv70OVFow5 SRzOvNLv kyyiWPwWN5I2vuDkl0374hj4dfCeaUROidkvJ1xG5BKZf49Lqfdg33adjTJ20bNER mPyIIaDfHAMwJ1vGcsbBvGUv

After logging in, select the “Setup” option.

n1I5CnZox6zTO uAInH EswKsL IEt8o1w KwImc gfteFdaChB9gZb6 GFGHPsb55pQgBKlEumJ7 Ntm6Dpozsyp8lKbrloq6153UpznZRpfWqzhMRDx

The Setup page will show the current model and firmware version of the system. This page should be sufficient enough information for any technician to help troubleshoot the system.

7PXVokgjOapSWH5YpiJX0ohBiM6WT

UNV Recorder || Finding Recorder Information || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

eVoSP 1TJ3Za699c7ylDYiDhFR krpuCgg TwgRfiYaT1OzlX2wuI4cZtZL5BwdrTUtgDB F5ziCPo0gNzavVrf0tLyToilRdYSPDQwTyZ7nvAwdeDWdYF6AN87S3mV77JMrgfdg

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Maintain.

5RDdyH cQhINUWSRuMEL23bODdJqPct67Yv2Aa1Yi7mva17pBkl8nBwOgbjnQVz 6EV 0JyR3fvYq8N7chGXjCJOik5GCUPM0oGmWoN0LZmSvqPRbnGX3YllcgescjphF6nqDaYF

After selecting the Maintain page, it will take you directly to the System Information page. This page will have most of the information for a technician to help troubleshoot the system if necessary.

sflkkOoNEN2H 1f neRyhIkE3q 523HzJgKsZA0mLtEHf32YgzMjjaGdkmclKUpwjBKE0e 3R iJNT Abe6qTLrzoNJ2Sce6GEQhuHo3XTBlfo5U8J7i8juHQuhl6V6uFjL4 pWs

UNV Recorder || How to View Recorder Logs || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

Fq1bjTyZV07OV1fJVuiN7T3a ntrclj4HjYj0YuUhunBpWU1aLmPAT3BHoSvhRpFmEr N35FbQhD5DLVhuD7YPPk dkrTv9gA1BykNIGsp88sXkWfWKNNeUfhzrg7i6MLb4BO4A

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Maintain.

On the Maintain menu, please select the Log tab.

JP8xawL7sludmEOrRZbrTOBsymq7xum9rwrR 2L19PEIKtWq2Sn nNFjeCF1WrNFLgUK56nlnMocpvfu5LdrUyDzDAlOL0INTlrpn8BsvOPHlAvGLPgNlVDbW3VpUhyzEaZJX5S1

On the Log page, select the time and dates for when to query the logs. This will populate a list on the current page for any actions or events that have taken place within the requested time frame. You may change the type of log search under the Main type. Exporting will create a text file with the log query as well.

sMsi5TOPBwRayM6hTk73juN5vdpYzDSdeApkqbkfEZyIjyXb4Zil6f0YoLQX6EYuym9vSrbB52WotfcQ6K5NnnSfncu5 AbM hoHXQ6536eIBs2ugvrR 6gTmbNYnvJp4mqcCdWH

UNV Recorder || Configuring Line Crossing || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

dm1qYFnrIv8PTkn6WhwRXzn4LAmnhwFZMPZzeSvRrHjyjIlre 12cg0ZtwLJjCcR2DfQJB3iQrY1hSrCdllYWJvBEfUdYPF hzZNaw6isRv1TDJa 3MBJInRmwmwBN4NbGYjucq

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Alarm.

sen28rh2Qb6 EhYgIuFotqw90aZgb57TAjv0iqVZ6D7uXdK8fB42DpXgwigaNa8xk1mRCyYA42r BWbbOnDh59ELNandsmP9ZaDPnmuvkotBfQsuePzUFiXYHEK8ivgwN1JSvHwW

After selecting Alarm, select VCA.

SxkGfXkAR23xn Uf9j8m2u9X3pb83JDxvaFzgLDiGojkGCPy49Q775NeRT8LDgbYF8nsdMWwnfRvrVEU7TKy7bKOiYhLKj7whDql5gFfDuau0LO6F ibBRZ75KBnRtt4J7Z2sYUA

After selecting VCA, select Cross Line Detection.

S0EHCIDX7DrQLlboYs2sxGmj64WBC6p2zm8jf1lTz BKnYSOoxdBdveG

On the Cross Line Detection page, you will be able to draw the line intrusions as wanted. Make sure to enable Cross Line Detection by marking the checkbox next to Enable.

vOVf0mHoLmWqkFjy5gWt6vxUQXlzSqf6JUFm PGHD0GzpGzpMILe4LmcJnBD7JfGASfRSexHzZ3PQy1ON2eT 6X 36miYtzXeoVITxIj3pTIECFW0FlWf HuIdJX8LoOJ zoDK5d

UNV Recorder || Factory Defaulting the Recorder || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

WrB Y6RrqJrzTxotmBHwnBLniTkSVm6pKnh3all8dhCQXES8N XN5EZQHB6wHgk7zWhJds3 Aqpm93M38RXepvWC

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Maintain.

On the Maintain page, please select the Restore tab.

uqiDCNkKDeeeatd9ui16Xq8exwgU iTlC6QeC q cYCU8mdezz3r6K4xioUWyvRE2szD3LnuY1kzy7JUDruFXzjxp2L878PxFDCitVpUsWjEjVe9utkx W ok HErhLTH1Ii po

On the Restore page, you will have the option to select to factory default all settings, or restore everything to default except the networking parameters. Regardless of which one is chosen, there will be a pop-up requesting to confirm the action. Once confirmed, the selected action will be performed.

Yltf kaU4XCZBt6KrNq3zS7oyVbmMumI0H r2yUODhwven8QIvBMm08YcYs QwmKOycTbopYi872LtS GZKqjwBQAGe8lcBqghnensTZfB1 sk1nQZTMHX5EOS8dKCsJyr3qrcsn

UNV Recorder || How to View Recorder Logs || Web GUI

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

M8JR9Yb2o kXsRp1cVppc YwEWdZ2IEJNKw74llHtcx2lcgvii 5cd6U41KG3M2lz1mu1zxVGq7xMJGRPYzq0E6bmhq5KqSh28PaOaSO0sJTc5mYNwWrOpi9uJJim X8zYwnVtwy

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

After logging in, select the “Setup” option.

mhkSC7Zvey iMu UgcGY7CHzIVDQ GdLxhcJXYdKme1zhHdjUsnG7FqPRCXgQNviHTZshW3girz1pXikkI yh2eZHQvQdGjWa gqm2pegXODWq4w6J5Q8aFMrcKkKfTWvPv nmlp

After selecting Setup, select Maintenance

7oDGCBQfwmw5 EescAvMaSjreJ8pnalLTWg CDuLTuFOflUWQpUzSR0z6B6eEVKFSVF 4zL5eLC j

Immediately after clicking Maintenance, it will direct you to the Log page where you can query the logs for the system. You can select the start/end time of the log search, as well as the log types.

yZojWZt9LSub8NBAMdL9l8cAMgOC0qSzG888K0T15HzC9KDxCg8049NUbQkTp nwZskZH

UNV Recorder || IPC Initialization || Web GUI

Please note: A Uniview NVR with Uniview cameras plugged into the internal POE of the recorder will essentially be plug and play. By default, cameras have DHCP enabled, however, when plugged into the back the NVR, it will receive a static IP address.

***It is important that all cameras are plugged in the same timeframe and that all cameras are connected prior to disconnecting any of the currently installed cameras. Failure to do so may result in an IP address conflict and will need further troubleshooting to resolve the issue.***

To access the web client, please use a Windows based PC and use Internet Explorer as the web browser.

Access the recorder’s web interface by typing in the IP address on the address bar of Internet Explorer. The path should look like the following: “http://xxx.xxx.xxx.xxx” (Note: If the HTTP port has been changed from default, you will need to add the port number after the ip address by inserting a colon “:” in between the address and port number).

MAY8FcIYW2z9XPWhyiOOFM MWrNpXX5KLxoRsctVfeWpch44K

Install all requested web plugins that are prompted by Internet Explorer. Once installed, you may need to refresh, or restart the web browser. You may install the plugin by selecting “Run”. In some instances, you may need to close the web browser to complete the installation. After installation completes, please re-open Internet Explorer.

Ta1YE1QY7CQoS88YwvFhZPpUHvKmax21aKEvYTIlPwB39pLJmrjvVrLn 8TQcjF Ks2 knbFsbpWiIeHk mbBI7YwCKAFJQt7MPpqOu7xK2BYNBW N 6eznQdXXaV0rWR6HqHjV6

After logging in, select the “Setup” option.

Ad5LK62jWBd0GFs4L5F oaKZApp5rJ hzwkyymg9KQ vK7cQoK juHaFw9JvmXakFdHyShhFsNyCystgTF2STD RC3zjpTloHZONkQV4SEn3gp25rswtl6

On the Setup page, select Camera on the left hand side menu.

yYagGIJa3X 4VzbIN9qFsNK43P12ydKTLsYyWG isNHUn qM9JGFjnkpxp5L6GJudZB0rF4nulQ4H6k29XIdgixFvPe4xYg3hnmYsswbqzwaO0GpiIJnBh8TPNa3WiA G Ro OU

Make sure that the channels are grayed out. By default, the plug and play address is 172.16.0.X Each Uniview camera will receive an IP address within this range if it is brand new, out of the box, or set to factory default.

By default, the system is set up for plug and play configuration.

NhRxNXNQj08Xi5jd4VJ0lG2cRJ7eyKI5P7BcaapPqN0tL2wXOZ0eGNxyP5Pyhc6OvipViGnLdHTxM 8mXOdGF83VoIEzXl clJmQGMm4WPnWpts2496a78Uh mmKe WlLIpZVSGK

UNV Recorder || Configuring Email Notifications || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

bPREuYiNsymgmX7ptoDr40kE3JK9Oq2ZoBoE Tr2VOI1qKv0dQBXV M1Fwq63hQPkxjephG hq0BUu24HwaF5e03tVH q 1AiUunHtSBjjj8dIJCGMwh8Hv48lGzwWqgB8uo1JfA

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select System

68RDKKQVlU5M ZRh1oTDlAyAIX9IlnmZ8AQBjYKXnYtJpqRzi1EdOZImTVfIpD3D

After selecting System, select Network

lxvOH6tWIMO3O a8W5IByA4CdIKjEICSrIyg94xCpbhXRcDyYs7NezKxI80zkCK4crSwtcogC1HbetRVmOFqAugXvhgA9FoNwXouwknh8re3MOVMxXm EifYLh9vTJOndV1 Qvrf

On the Network page, confirm that all settings are correct for the recorder to access the internet. After doing this, select the Email tab.

wuSb EVZ2mBloV mlrFKdsJC0UlU xE1HhUm9ryo sOn16Sspjv0DdFVxy b1316nqXmos0K8S3ZIs2zyQAFAgKst67DlpsH59Hp9GnJ69VMnLZJMoAS6 lCmo8hNdNSZDW5vlFL

Fill out all the necessary information for the email page. Some email provider information may be different, please refer to the email provider for additional information. Below will be an example on how to set up an email for Google’s Gmail service.

j8Iy9HgV3Ks2LXzdobMabc BomiCSTkhhvaaIY6wAam qqyYRRfrVzcGzUHMB yQcmfLxEUO5EhUbjjkQLCvaq7voB8S14Dji76le hN62mddvPjU 3u516vvl Gu9QLDQQVqgR8

54ZCzNx

***Please Note: For Gmail accounts, you will need to allow less secure apps to sign on to your account. This setting can be found in the account settings under security for the Google account***

If you receive failure messages please log in to the gmail account as the first account and click the link: https://accounts.google.com/b/0/DisplayUnlockCaptcha to unlock the account

UNV Recorder || Configuring Intrusion Detection || Local GUI

Log into the system by entering the username and password. Default credentials are admin for the username and 123456 for the password.

CBomQuP ofFDqpErIHiGtyalrWmhTZN6mSPd54DBoJQW6Q6YoC1ZDaZ 1sd1Eh3gXqvwqdD0QedSXhUFSO 4Zq vB9sSIwAO

After logging in, move the mouse to the lower left hand corner of the screen and select the home icon. You may receive the login screen after selecting the menu option, but will be taken to the main menu page once logged in. On the main menu, select Alarm.

uDP9DvEbLDwhN55J0rJjwmunjtYZe4ZR4Nj93WI9va9FgfD573imKsBVlmswxNCcKI MJ4qH2e4DWdgog5eOVyIHCLh45eBR9c1dI vYb7hbmlBCoJIiY9e 6jAW9FnOpUvnEQXo

After selecting Alarm, select VCA.

Z36Hx56CHbSXpIQUfQujYlVKHBEC7eYnuf2WD6TcVMlanmeCT4TOmfGf74 jwTf6FYPddu1abVHe8LdXFNXKHHcacBGbpRpmGLFFIWPYC1plua8kZqydaQk0H69jSAlc cURZE0Z

After selecting VCA, select Intrusion Detection.

3aSz5Fgx1wEl

On the Intrusion Detection page, make sure the checkbox is marked to enable intrusion detection. Select the pencil icon next to Draw Line. Create the perimeter and select Apply.

N0DpMiOn1IFpvjJZBY6WPko2jwWG1SKEowG0yMd82GZZVh4cPMic8QoJoRzdZ4DF1yiDhXq14vanMsJoIp2I1g3zDM4MRxW0Y

]]> https://www.xvraid.com/guide/unv-recorder-set-up-guide.html/feed 0 KBVISION XVR Firmware https://www.xvraid.com/firmware/kbvision-xvr-firmware.html https://www.xvraid.com/firmware/kbvision-xvr-firmware.html#respond Mon, 16 Jan 2023 06:55:02 +0000 https://www.xvraid.com/?p=1274 KBVISION XVR Firmware Summary of Firmware for Kbvision‘s HD-Analog recorder. Firmware versions are updated from time to time.Note about fixing the error: “invalid camera format” : Not supported on H2, H3 . series D6 series, SD6 only support with FW from 2018 and earlier H1 series only support with FW from 2019 and earlier Other series like D/F4, D4, D5 don’t have this problem.

KBVISION XVR Firmware
KBVISION XVR Firmware

KBVISION XVR Firmware

Read Next : How to Upgrade Standard Firmware for XVR NVR

1. Firmware for D6 – SD6

1. KX-A7104SD6, KX-A7108SD6, KX-7104SD6, KX-7108SD6, KX-7114SD6, KX-7118SD6, KX-7104D6, KX-7104TD6, KX-7108D6, KX-7108TD6, KX-8104D6

STT DAY VERSION NOTE DOWNLOAD
first October 13, 2020 V3.218.100Z200.0.D KB- Fix playback error on KBView Plus Download
2 05-02-2021 V3.218.100Z202.0.D KB – Fix playback on 4G/ KBView Plus Download
  • Firmware supports “invalid camera format” for D6 series (need to upgrade main fw file + logo):
STT DAY APPLICABLE MODEL DOWNLOAD
first January 17, 2018 KX-7104TD6, KX-7108TD6, KX-7104D6, KX-7108D6, KX-8104D6, KX-8104TD6 Download
2 January 17, 2018 KX-7116D6, KX-8108D6, KX-8108TD6 Download
3 January 17, 2018 KX-8116D6, KX-7232D6 Download
4 January 30, 2018 Logo – domain name Kbvision Download

2. Firmware for H1

1. KX-7104H1, KX-7104TH1

STT DAY VERSION NOTE DOWNLOAD
first 15.05.2020 V4.001.100Z200.0.CHEAP KB – Security Update Download

2. KX-7108H1, KX-7108TH1, KX-8104H1, KX-8104TH1, KX-D8104H1, KX-D8104TH1

STT DAY VERSION NOTE DOWNLOAD
first 02-06-2018 V4,000.100Z101.0.CHEAP KB – For 8104H1 with fan Download
2 11/24-2020 V4,001.100Z201.0.CHEAP KB – For fanless 8104H1 – Supports CVI 5MP 16:9 Download

3. KX-7116H1, KX-C7116H1, KX-7216H1, KX-C7216H1, KX-8108H1, KX-8108TH1, KX-D8108H1, KX-D8108TH1, KX-2K8104H1, KX-D2K8104H1, KX-4K8104H1, KX1D4K8104H

STT DAY VERSION NOTE DOWNLOAD
first 11/24-2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download

4. KX-7232H1, KX-C7232H1, KX-8116H1, KX-8216H1, KX-8416H1, KX-D8116H1, KX-D8216H1, KX-D8416H1, KX-2K8108H1, KX-D2K8108H1, KX-4K8108H1, KX-D4K8108H1

STT DAY VERSION NOTE DOWNLOAD
first 11/24-2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download

5. KX-8232H1, KX-D8232H1, KX-8832H1, KX-D8832H1, KX-8432H1, KX-D8432H1, KX-2K8116H1, KX-D2K8116H1

STT DAY VERSION NOTE DOWNLOAD
first 11/24-2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download

3. Firmware for H2

1. KX-DAi8104H2, KX-DAi8104TH2

STT DAY VERSION NOTE DOWNLOAD
first November 18, 2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download

2. KX-DAi8108H2, KX-DAi8108TH2, KX-DAi2K8104H2

STT DAY VERSION NOTE DOWNLOAD
first November 18, 2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download

3. KX-DAi8116H2, KX-DAi2K8108H2

STT DAY VERSION NOTE DOWNLOAD
first November 18, 2020 V4,001.100Z201.0.CHEAP KB – Supports CVI 5MP 16:9 Download
2 May 18, 2021 V4.001.100Z202.0.D KB – Fix sesame noise on CVI cam Download

4. KX-DAi8232H2, KX-DAi8432H2

STT DAY VERSION NOTE DOWNLOAD
first July 14, 2021 V4,001.100Z201.0.CHEAP KB – Security Update Download

4. Firmware for H3

1. KX-DAi8104TH3, KX-DAi8104H3

STT DAY VERSION NOTE DOWNLOAD
first May 24, 2021 V4.001.100Z200.1.cheap KB – Vietnamese language support Download
2 05-05-2022 V4.001.100Z202.0.R. KB – Fix Ai-Code interference Download

2. KX-DAi8108TH3, KX-DAi8108H3, KX-CAi7116H1

STT DAY VERSION NOTE DOWNLOAD
first 05-02-2021 V4.001.100Z200.0.CHEAP KB – Firmware security update Download
2 July 21, 2021 V4.001.100Z200.1.cheap KB – Fix fast forward / stutter when playback playback Download
3 05-05-2022 V4,001.100Z202.0.CHEAP KB – Fix Ai-Code interference Download

3. KX-DAi8116H3, KX-DAi8216H3, KX-DAi8416H3

STT DAY VERSION NOTE DOWNLOAD
first May 23, 2022 V4.001.100Z200.0.D KB – Fix Ai-Code interference
Fix crashes when switching IPC channels (Leave 2)		 Download

4. KX-DAi2K8108H3

STT DAY VERSION NOTE DOWNLOAD
first February 19, 2022 V4.001.100Z200.0.CHEAP KB – Fix Ai-Code interference Download

5. KX-DAi2K8116H3, KX-DAi2K8216H3

STT DAY VERSION NOTE DOWNLOAD
first 09.05.2022 V4.001.100Z200.0.CHEAP KB – Fix Ai-Code interference Download

6. KX-DAi8232H3

STT DAY VERSION NOTE DOWNLOAD
first 09.05.2022 V4.001.100Z200.0.CHEAP -Kbvision.tv domain -Fix
Ai-Code interference		 Download

5. Firmware for -D (H.264 – 2021)

1. KX-D8232-D, KX-D4232-D

This series supports 5MP 16:9 aspect ratio CVI camera. H.264 . compression diagnostic

STT DAY VERSION NOTE DOWNLOAD
first September 28, 2021 V4,000.100Z200.0.CHEAP KB – Security Update
-Kbvision.tv . Domain		 Download

6. Firmware for 7xxx (Ai)

1. KX-7104Ai

STT DAY VERSION NOTE DOWNLOAD
first August 17, 2021 V4,001.100Z201.0.CHEAP KB – Fix noise interference
-Kbvision.tv domain name		 Download

2. KX-7108Ai

STT DAY VERSION NOTE DOWNLOAD
first July 21, 2021 V4.001.100Z200.0.CHEAP KB – Fix noise interference
-Kbvision.tv domain name		 Download

2. KX-CAi7108H1

STT DAY VERSION NOTE DOWNLOAD
first July 16, 2021 V4.001.100Z200.0.CHEAP KB – Fix noise interference
-Kbvision.tv domain name		 Download

Note: Upgrade the correct Firmware for the correct device model and ensure a stable internet connection during the upgrade. Upgrading the wrong Firmware can lead to device death .

]]> https://www.xvraid.com/firmware/kbvision-xvr-firmware.html/feed 0