Installation and configauration

4G SD Card installation and configuration

Note: Before configuring the device, please confirm the status of the WIFI/4G dial switch of the device. When the dial switch is placed close to the side of the 4G card slot, it is in the 4G configuration mode; the dial switch is placed to the side away from the 4G card slot. When it is WIFI configuration mode. Switching the status of the dial switch must be performed while the device is powered off.

Eseecloud 4G Solar Camera Guide

Read More :

1. ClareVision Cameras Setup Guide
2. Uniview IP Security Camera Guides
3. How to setup Arlo Home Security System

Add 4G camera

1. After successfully downloading and installing the APR, log in to the App;

2. Click “+” in the device list (Figure 1) Jump to the QR code scanning interface.

Fast Installation Manual

Switch near to 4G SIM card slot,camera in 4G mode

(Figure 2);

3. When your device has a 4G card with Internet, and the dial switch is placed close to the side of the 4G card slot, please check the process of 4G mode addition in 1.1; When the dial switch is placed to the side away from the 4G card slot, please check the process of WiFi mode adding in 1.2.

■ 1.1 Add process with 4G mode

Before operating this unit,please read these instructions carefully,and save them for future use.

Status light prompt of 4G camera tail line:

In 4G mode:

1. .Slow flashing: The 4G module is abnormal or the SIM card is abnormal, and flashes once every 2s.
2. .Fast flashing: No dialing number (no flow or bad signal), flashing once every 0.5s.
3. .Always on: The network is normal.

In Wifi mode:

1. .Slow flashing: In hotspot mode, flashes once every 2s.
2. .Fast flashing: The device is configured to the router, but the connection is disconnected, flashes once every 0.5s.
3. .Always on: The network is normal.

n

1. .Make sure the device has an available 4G card ,and WiFi/4G dial switch is placed to the side of the 4G card slot;
2. .Connect the device to the power supply and wait for the device indicator to become normally on ;

a There is a QR code on the device :

1. .Scan the QR code of the camera body (Figure 1), and click “Add” on the search device page (Figure 2);
2. .Set the device name(Figure 3), after confirming, return to the device list to display the device (Figure 6).

a Device QR code cannot found:

(1).Click “Other ways to add” on the QR code scanning interface(Figure 1);

(2).Select the connected device (Figure 4);

(3).Input the device ID and name in the ID adding interface, click complete in the upper right corner (Figure 5), and return to the device list after adding is successful (Figure 6).

Fig 4

Fig 5

H

Fig 6

CONNECTED

IPCS48618T7834161

TP-LINK_N750

Xiaomi_4BF8_5GGD rc

TP-L!NK_N750_5G

PDCN_5G <■

CaoHHAriPort

NETGEAR.5G

Saved

Add Device

Fig 2

Fig 3

Product

Please input WiFi password

Configure the network

The phone is connected device WiFi:IPC 4123

O 0 0 O

Scan code Even hotspot Select add Complete

View.(most peop e choose)

Direct Connection:

View video without network .select Direct Connection.(few people choose)

Tip: 5GHZ wireless network is not supported at this time

Direct Connection

It takes a few minutes for the device to match wifi, Please wait…

78%

Need to wait for a while, do not disconnect
the network!

■ 1.2 Add process with WiFi mode

1.2.1 Adding Process to Non-networked Devices

(1).Make sure the dial switch is placed to the side away from the 4G card slot; (2).Connect the device to the power supply and wait for the device indicator to flash slowly (in hotspot mode, flash once every 2s);

(3).Please go to the phone system settings and select the device hotspot starting with IPC. The default password is 11111111 (Figure 1) (Hint: please keep connected with the device hotspot during the connection process).

□ There is QR code:

1. .After connecting to the hotspot, return to APP, scan the QR code of the device (Figure 2), and click “Add” on the search page (Figure 3);
2. .View video via WIFI or other network, please select Remote View.View video without network , select Direct Connection.

Remote view: Click the “Remote view” button (Figure 4) to go to the configuration network interface. The system will display the WiFi search near the device below the interface. Select or input the routing WiFi name and password at home (Figure 5) and click OK The device is configured with WiFi (Figure 6). After the configuration is successful, follow the interface to complete the device name and password settings (Figures 7 and 8). After the addition is successful, return to the device list.

Direct Connection: Click the “Local direct connection” button (Figure 4), pop-up box for setting the device name, follow the interface content to complete the device name and password settings (Figure 7, 8), and return to the device list after adding successfully.

a Device QR code cannot found:

1. .After connecting to the hotspot, return to the APP, enter the QR code scanning interface, and click “Other ways to add” (Figure 2);
2. .Select the wireless standalone camera (Figure 9). For the subsequent network configuration steps, please refer to the second step of adding the QR code on the device.

H

1.2.2 Add process of networked device

□ When there is a QR code on the device:

1. .Scan the QR code on the device (Figure 1),click “Add” on the search page (Figure 2);
2. .Set device name (Figure 3), Input the correct password (Fig 4) (skip this step if there is no password), and return to the device list after adding successfully.
3. If unable to find the QR code on the device:
4. :LAN search device and add process
5. .Please go to the mobile phone system settings and connect the hotspot of the device to ensure that the mobile phone and the device are under the same WiFi;
6. .Open the Eseecloud APP and enter the QR code scanning interface, click “Other ways to add” (Figure 1);
7. .Select LAN scan (Figure 5);
8. .Select the required device ID in the scanning interface (Figure 6), click Add to enter the ID adding interface, input the device name and password, click Complete in the upper right corner, then return to the device list after adding successfully.

2: Add networked device process

(1).Open the Eseecloud APP and enter the QR code scanning interface, click

“Other ways to add” (Figure 1);

1. .Select the networked device (Figure 5);
2. .After enter the device ID and password(Figure 7), click Complete in the upper right corner, then return to the device list after adding successfully(Fig 8).

1.2.3 Wired connection configuration mode

1. .Confirm that the device is connected to a router with internet access through the network cable;
2. .The subsequent adding steps are the same as the adding process of networked devices in 1.2.2.

4G spotlight camera management Flow recharge and abnormal conditions

■ 2.1 4G spotlight camera management Flow recharge

4G card management:

1. .When the flow is sufficient, it will be displayed normally (Figure 1). When the flow reaches the warning value, it will display the current remaining flow (Figure 2);
2. .Click the 4G card management (Figure 3) or the traffic alert value prompt text in the settings to jump to the 4G card management interface (Figure 4), and you can view the traffic usage, signal level and other information of the 4G card in the current interface.

□

4G card traffic recharge:

(1 ).ln the 4G card management interface, click the “flow recharge” button (Figure 4), enter the flow purchase interface (Figure 5), select the package and payment method, and then click pay now (Figure 6);

(2).After the payment is completed, it will return to the app and display the result details. After the recharge is successful, it will display the recharge device, flow and other information (Figure 7).

Note: The effective time of recharging is expected to take effect within one hour according to the situation of each operator.

Fig 1

Device: 4G card machine

Please choose to purchase a package

I The hottest 10G traffic package Q

recommended

Period : 6 month ¥ 300.00

Latest 1G Traffic Package Recommended

Period : 3 month ¥ 100.00

Offer 1G data package O

Period : 3 month ¥ 100.00

Preferred 10G traffic for business trips

Period : 1 month ¥ 100.00

® I have read and agreed Sales agreement

Fig 5

fh Share 0 Info 5 Playback ® setup

1961121876

My device5 .ill online

Fig 2

Help

Basic settings

4G card management

Device WIFI

Enable audio recording

Voice prompt

Device with voice prompt after start

Device volum

Restart the camera

El

Total flowl 50GB 120GB remaining

Refresh

Traffic alarm push CD

Signal strength weak

Valid time 2019-2-1 to 2019-7-31

Carrier information

View card package

Fig 4

■ 2.2 4G card device abnormal conditions

When the 4G card device has no traffic and the package expires, the device list displays the corresponding status (Figure 1 and 2). Click to view the details to enter the 4G card details interface, display the corresponding status

(Figure 3 and 4) according to the offline reason of the device list, and click the flow recharge to enter the 4G card flow recharge process.

Note: when the camera is inserted into the 4G card that is not provided with the device, it will not support the functions such as recharge of the traffic package, traffic query, early warning, etc. (Figure 5).

4G card machine .,il offline

4G card machine ,.H offline

Warning

In case of fire or lightning,pls don’t put product in damp andraining place,operate or maintain the device according to the user manual.

Be careful when you see

attachment with a Dangerous Voltage which might cause serious electric accident.

Notice:

1. Ensure your equity,pls read the user manual carefully before you use the product
2. Pls contact professional people if you need install and maintain the product
3. Input voltage of this model is DC 12V
4. Working Environment:temperature of -20°C~+60°C, relative humidity under 85%
5. Pls don’t exceed the user manual’s standard range of temperature,humidity and voltage.

What is a Tp-link tapo FAQ camera & how do you install a Tapo camera outside?

Before we begin:

1. Please download Kasa Smart from App Store or Google Play and install it on your smartphone.

2. Connect your smartphone to your home Wi-Fi network.

3. Plug your Kasa Cam into a power socket.

Here we use KC120 for example

Step 1:  Open the Kasa App

Log into your cloud account. Please refer to the link to sign up if you don’t have a cloud account.

Step 2: Tap “+” button to add a Kasa Cam, select “Add a Device”, and choose “Cameras” icon according to your model number.

Step 3:  Follow the instruction on the Kasa app to power on the Kasa Cam, wait for the light blinking orange and green.

If the light do not blinking orange and green, please reset the Kasa Cam as per UG/QIG.

Step 4: Connect your phone to the Kasa Cam’s Wi-Fi network.

For Andriod:

Kasa will look for your Kasa Cam automatically, and it will take about a minute.

If you have a problem with this step, please go to Settings->Wi-Fi on your smartphone and manually connect to Kasa Cam’s Wi-Fi network (same as iOS).

For iOS:

You need to connect to the Kasa Cam’s Wi-Fi network manually, please go to Settings->Wi-Fi on your smartphone and manually connect to Kasa Cam’s Wi-Fi network (which is named Kasa_Cam_xxxx), and then go back to the Kasa app to continue the setup process.

Step 5:  Choose your home network to connect, enter the password of your home network.

Step 6: Name your Kasa Cam

Step 7: Enable Activity Notifications. If you enable this function, your camera can alert you whenever it detects motion. If you don’t want to be notified, click on “I don’t want to be notified”.

Step 8: Follow the instruction to mount your camera. If you do not want to do it now, click on “No Thanks”, and we have completed the setup of Kasa Cam.

What should I do if I forgot the password of VIGI NVR

If you forget the password of the VIGI NVR, you can reset the password via VIGI NVR.

Step 1. Click the Forgot Password option on the login window.

Step 2. Send the Verification Code to your Reset Password Email.

• If your NVR is connected to the internet

1. Click the Send Code and you’ll receive a verification code sent to your Reset Password Email.
2. Enter the verification code you received into the blank under the QR code and click the Verify button. Then you can set a new password for your NVR

• If the NVR is not connected to the internet

1. Download the VIGI app from the Apple App Store or Google Play or scan the QR code to download the VIGI app.

2. Open the VIGI app, log in with your TP-Link ID. If you don’t have a TP-Link ID, sign up first.
3. Tap the “+” on the top right to scan the QR code on the left of the VIGI NVR. Then you’ll receive a verification code sent to your Reset Password Email.
4. Enter the verification code you received into the blank under the QR code and click the Verify button. Then you can set a new password for your NVR.

 Note:

1. What’s the Reset Password Email?

Reset Password Email is the one you entered in Quick Setup for the password reset. It is only used to receive the verification code when you need to reset the password.

2. What should I do if I don’t receive the verification code?

• Check your junk or spam folder.
• Add noreply@tp-link.com in the White list (by clicking Create a new filter) in your email setting.
• Check your email filter setting in your email account.

If the above steps don’t solve your problem, you can refer to the link to reset the VIGI NVR.

Get to know more details of each function and configuration please go to Download Center to download the manual of your product.

How to upgrade the firmware of VIGI NVR?

If you want to upgrade the firmware of VIGI NVR, please follow the steps below:

Step 1. Right-click on the screen, click Settings on the Main Menu.

Step 2. Go to Settings -> System -> Firmware Upgrade.

Method 1: Upgrade firmware online

1. Click Check for Update.

2. Click Upgrade, and the NVR will be automatically upgraded.

Method 2: Upgrade firmware locally

1. Please find your NVR at TP-Link Download Center, download the latest firmware of your NVR and save the file of firmware to your USB drive. Insert your USB drive into the USB port on the front panel of the NVR.
2. Click Select upgrade firmware and select the firmware you need for the upgrade.

3. After the import of firmware, the NVR will be automatically upgraded.