What error message do you see on the screen?

We need to identify first the error message that your screen shows.

 .

 (from a DVR-4900/8075)
 (from a DVR-5580/5680)

 .

Here is an overview of the things we need to check:

 .

1. Camera to extension cable connection

For some of you who installed the cameras already and forgot to test the cameras first, that’s alright. You can skip this step for now. You just need to make sure that the 2 connectors of your camera are both connected firmly to the extension lead; otherwise, you might end up with a powered camera but no video connection or a powerless camera with a video connection. Check the image below, that’s how your camera needs to be connected to the extension cable.

a. Connect the power connector

b. Then connect the BNC video connector

Here is what it should look like after the connection.

2. Extension cable to power splitter

The extension will have 2 connectors on each end and you already used one end for the camera’s video and power connection. The other end of that cable needs to be connected to the power splitter especially if you have multiple cameras on your setup (disregard the splitter if you are dealing with an additional camera since it will come with its own power supply). The splitter will have 4 leads on one end and a single lead on the other. Pick one lead from those 4 and connect the power lead of the extension cable to it. See the image below on how it should be connected.

.

3. Power splitter to the power adapter

Grab the single lead from the splitter and connect it to the power adapter. Use the provided 12v power adapter from the kit. Then plug the power adapter into a working power point, wall outlet, or power board.

4. Extension cable to the DVR

Going back to the extension cable, we are left with one connector. That connector will be connected to the ports at the back of the DVR. These ports are normally labeled as Video In or Video Input. You need to push the BNC connectors and twist them to lock them firmly to the DVR. Check below on how to connect the BNC cable to one of the video connectors at the back of the DVR.

You are all set! Live feed from the cameras should now display on the TV/monitor. If in case it didn’t, you might want to check Video Loss Troubleshooting for DVRs for some advanced troubleshooting.

Swann DVR Troubleshooting Guide

Read More : Swann Camera Troubleshooting

.

Hard drive warning: Unformat error / Status: Abnormal 

This applies to recorders that were pre-installed with internal hard drives (HDD) and worked before. This error or warning appears when the hard drive is no longer recording or can no longer be accessed but is still detected.

 .

A. The HDD LED is solid, indicating the hard drive is still detected but is not reading/writing.

B. The HDD status (Menu > Device > HDD) shows “Abnormal” or “Unformat error”.

C. The HDD Free/Total capacity shows 0GB.

 .

A. & B. If Unformat error / Abnormal error shows

Do each step in the following order to remedy the issue:

A. & C. If Total Capacity is 0GB

Do each step in the following order to remedy the issue:

Note: Formatting will not erase the Swann firmware.

.

No hard drive or hard disk found 

This applies to recorders that were pre-installed with internal hard drives (HDD) and worked before. The following are signs that the hard drive is no longer detected in your DVR / NVR:

A. The HDD LED is off.

B. The HDD status (Menu > Device > HDD) is blank, meaning No. 1 is empty.

C. You may have experienced an outage or changed the power adapter.
.

A. & B. If you changed the hard drive recently

Bear in mind that only certain types of hard drives are compatible with CCTV security systems.

• We recommend using a surveillance-rated hard drive of the same size dimensions and storage capacity as your recorder’s hard drive, such as the Western Digital Purple, Seagate Skyhawk, or Toshiba Surveillance range of drives. If you wish to know the maximum capacity and size compatible with your DVR or NVR, you can request a Chat for “hard drive” and follow the prompts.

• Solid State Drives (SSD) for DVRs are NOT ideal for continuous recording, operation in high temperature setting, and large disk space. A DVR’s intention is reliability not speed. SSDs are very fast, but it will wear out eventually when writing happens frequently. Using an SSD is at your discretion.

• Desktop hard drives are not recommended as their low speed can cause playback skipping and errors. They are not optimized to support 24/7 read-and-write access.

Please visit Installing an additional Internal Hard Drive (HDD) for 16-channel Recorders for an example of how to change the hard drive of your recorder.

 .

A. & C. If you experienced an outage recently

The power adapter for your recorder was designed to protect the DVR or NVR in the event of a surge or power outage as adapters can be replaced easily unlike the whole recorder. Chances are the power adapter may be providing insufficient power for full recorder function (which includes the hard drive).

1.Ensure you are using a power adapter with the correct output rating for your recorder. See What power adapter should I use? for your DVR, NVR or NVW.

2.In the event of an outage, unplug all connections at the back except the TV, mouse and power adapter. This is to check whether the hard drive will be detected and whether the power adapter is still providing some power.

3.Change the power adapter to a known working one that has the same output rating as in step 1.

If the hard drive is detected after unplugging the cameras, chances are the power adapter is providing insufficient power and requires replacement.

If you are already using a compatible hard drive and a known working compatible power adapter, chances are the hard drive needs to be replaced. Please check What hard drives can I use with my DVR or NVR?

Swap DVR Power Adapters for Boot Issues 

The power adapter of the DVR and the power adapter of 4 PRO- camera models are interchangeable as long as they have the same output rating of 12V 2A.

We do this to test whether the power adapter is faulty or the DVR is faulty. Power adapters are designed to protect the DVR in the event of power outages or power surges.

Warning: Do NOT use a power adapter higher than 12V on the DVR. Doing so will void your warranty.

Step-by-Step Instructions

Note: If you have 8 cameras or more, you can swap the cameras’ power adapters instead of the DVR power adapter as long as both camera power adapters have the same output rating.

.

What hard drives can I use with my DVR or NVR? 

This applies to Swann recorders with pre-installed internal hard drives for recordings. The type of hard drive compatible with Swann DVRs and NVRs are surveillance-type hard drives, which are connected via SATA cable. Before you decide to upgrade your internal hard drive, you MUST know the type, capacity, and size that your model is compatible with:

Compatible Type by Brand

 The following surveillance hard drives are compatible with Swann recorders:

• Seagate Skyhawk by Seagate

• Western Digital Purple by Western Digital

They vary in capacity and size, so check below to identify what is compatible with your recorder.

Compatible Capacity

This is the maximum number of storage capacity in gigabytes or terabytes that a hard drive has which varies in compatibility with your recorder.

Most Swann recorders are pre-installed with a hard drive internally. If you wish to upgrade the capacity of your hard drive, you need to check with our Technical Support for the maximum capacity that your recorder model will support. The maximum capacity varies by model number.

Customers with Swann Security and HomeSafe View app-compatible products can inquire via phone.

Compatible Size

Should you wish to upgrade your hard drive, ensure to acquire the same size dimensions as the one in your recorder. Surveillance-type hard drives come in two sizes:

If you are unsure, customers with Swann Security and HomeSafe View app-compatible products can inquire via phone.

Compatible with External Hard Drives

If your DVR or NVR has an eSATA port on the back panel, it means your recorder is capable of connecting an external surveillance-type hard drive.

The function of the external eSATA port may either be for exporting recordings or recording depending on the chipset of your recorder model. For example: Can I use an external SATA hard drive to my DVR8-3000 to increase recording capacity?

The following recorder series have an external eSATA port for a hard drive of up to 3TB in capacity for external recording:

Compatible microSD Cards 

If your recorder model contains a microSD slot, it can support up to 128GB capacity for the microSD card.

The following recorder models are compatible with up to 4TB capacity for the hard drive and 128GB capacity for the microSD card.

Note: Simultaneous recording to both the internal hard drive and microSD card is not supported. If there is a hard drive internally, recording to the hard drive will be prioritized.

Not Compatible

DVR/NVR went offline after an outage or changing routers or Internet Service Provider 

This article applies to DVRs or NVRs that are hardwired to your router, and affects mobile or computer streaming, push notifications, and other features requiring internet connectivity.

The DVR or NVR going offline is a common occurrence when changes were made to the router, its settings, an outage, or changes in IP by your Internet Service Provider (ISP). In order to get it back online, you must have physical access to the DVR or NVR to check the following:

1. If there was a Power or Internet Outage

Normally, turning off the recorder and then turning it back on again will get the DVR or NVR to re-establish communication with your router. However, this will only work if its Network setup is set to DHCP by default. This ensures that the router is able to detect the DVR/NVR via ethernet and update its IP address.

If rebooting did not work, please try additional steps from this article: Remote Access – Basic Router/Network Troubleshooting.

If the live view is blank, then the outage may have affected the power supply. Check this article to troubleshoot: Troubleshoot a Boot Failure or Rebooting issue of a Recorder (DVR/NVR/NVW).

2. If you changed or replaced the router (changed ISP)

See types of routers that may or may not work with the DVR or NVR in this article: Network Setup: What do I need for my DVR/NVR to go online?

If the router is compatible, then the connection between the recorder and the router just needs to be refreshed. See this article for the first few steps to re-establish the network connection: Remote Access – Basic Router/Network Troubleshooting.

3. If you added another router or extender

Ensure that the network connection setup has not changed. If the DVR or NVR is still connected to the same router, but that router was connected to a cable modem instead of a wall, then the setup is no longer a direct connection but a bridged connection.

See why the DVR or NVR may not work with a bridged router or particular extender in this article: Network Setup: What do I need for my DVR/NVR to go online?

How to factory reset my DVR / NVR (V8) 

Default Settings VS Factory Reset

To load settings to default in recorder models, you must be logged into the recorder via TV and mouse or computer software.

How to restore settings to factory default via TV and mouse

You must know the user name and password of your recorder in order to do this method. If you do not know the password, you need to perform a password reset instead. See How to reset the password or get the recovery code of your DVR/NVR/NVW

1.Right click on Live View or go to the Task bar.

2.Choose the first icon: Setup.

3.Go to Advanced > Maintain (tab).

4.Click on Load Default.

5.Check System> Save.

You will be taken to the Startup Wizard to set a new password. See Frequently-asked questions and tips to complete the Startup Wizard

How to restore to factory default via Windows software

The DVR or NVR must already be added in the software beforehand and is online in order to do this method. If your DVR or NVR has not been added, you need to perform a password reset instead. See How to reset the password or get the recovery code of your DVR/NVR/NVW

Via HomeSafe View software: 

Go to Control Panel > Group Device Management > Devices: hover over Device > click on Remote Config (wrench icon) > Advanced > Load Default > Check the appropriate box > Save.

Via Swann Security VMS software:

Go to Device Management > Advanced > Load Default > Toggle the appropriate options > Save.
 

Warning: Once you have restored the recorder’s settings to default via software, you are required to set a new password via TV and mouse hardwired to the recorder. If you are unable to login to the Main Menu nor access your recorder via software, you need to do this: How to reset the password or get the recovery code of your DVR/NVR/NVW

Troubleshoot a Boot Failure or Rebooting issue of a Recorder (DVR/NVR/NVW) 

If you your Swann recorder (DVR, NVR, NVW or wireless recorder) is experiencing the below issues, then your unit may have a boot failure problem:

To isolate, consider following the steps below

• Power rating – the common output rating for DVR PSUs is 12V / 2A (2000mA) and 12V / 1.5A – 3.75A for NVRs depending on the model of the recorder. 

 Note: Some of the older DVR PSUs use 12 V / 3A and 48 V / 5 A for NVR. For a list of Power Adapter (PSU) ratings appropriate for your device, please check this What power adapter should I use article.

• Red tag label – most of the power adapter included has red sticker along the power cable to indicate its use (e.g. DVR/NVR or Camera).  

2.Plug to a wall outlet – to eliminate possibility of faulty extension cable or UPS.

 

3.Unplug some cables – if you have an Ethernet cable or cameras already connected, disconnect them for the meantime. Only leave the power plug and monitor connected.

4.Secure connection – ensure that the power plug is connected securely to the recorder and not loose.                            
Note: Some of the older NVR PSUs use a larger Barrel plug.

5.Turn on the recorder – some units may have power switch at the back. Ensure that it is switched ON.                                        

6.For DVR and NVW-800/AllSercure 650 units, if the NO power issue still persists, swap the camera PSU with the recorder to isolate problem. Check this article for the guide.

Note¹: If the recorder remains turned Off, check if the wall outlet where the Power Adapter (PSU) is plugged in has power.

Note²: If the recorder turned On but seeing a black screen, consider checking if your monitor support the correct screen resolution by following this guide – Video Mode Not Supported or Signal Out of Range or No Signal.

Why does my DVR / NVR / camera stop recording motion after a minute? 

DVRs and NVRs are set to record PIR/motion by default. Wireless standalone cameras can only record by PIR/motion. Where the camera is mounted can have an impact on how effective movement is picked up and recorded.

Mounting any camera with thermal and motion sensors in the wrong location and angle can prevent recordings of certain movement. For example:

• Movement in the directions indicated by green arrows are more likely to be detected.

• If the movement is toward and away from the camera at a short distance, the camera sensors may not be able to identify the changes between frames because the differences are subtle.

• If the movement stops, the DVR / NVR will stop recording. This means an intruder could still be standing on the same spot with subtle movements long enough to thwart the PIR/motion sensors.

Please see the fixes specific to your model for working around PIR/motion:

Fix for DVR: Set the already-mounted DVR camera to record continuously

This setting is ideal if you mounted your camera above your front door, and you expect the camera to record regardless of motion.

See How to Set Up 24-hour continuous recording for a Camera (DVR or NVR only)

Fix for NVR with V8 firmware: Set up Analytics for your NVR camera.

Perimeter Intrusion Detection (PID) with PIR can be configured for one NVR camera if you have a V8 recorder and camera.

 A perimeter intrusion region can be used to define specific areas that you want to monitor for motion. For example, a rule can be defined so that your NVR will alert you if one or more objects have entered the boxed region from a particular direction and stayed within the intrusion region for a particular time.

Please see the user manual for your NVR on how to set up PID: User Manual (V8 units – 8580, 8580RN, 8780, 8780RN,)

 .

Fix for any camera, especially WiFi cameras: Reposition the camera or add another camera for a different angle of view.

The ideal position of the camera is 7-8 feet high, pointing downwards at an angle to cover the area where people will be walking across the camera’s path

Swann Camera Troubleshooting

Let’s discuss Swann camera troubleshooting. Like any other brand of Wi-Fi or IP camera for consumer-grade surveillance, you will come across common errors that you can solve easily in a DIY fashion. Refer to this guide for more details.

The Swann brand claims itself to be security made smarter. It backs up its claim by making some of the world’s best value security system. They’re able to compete against the likes of Ring, Nest, Arlo, Bink, and Wyze by providing the smartest of features and the most intuitive of controls.

Regardless, in case your Swann camera stops working, isn’t recording, isn’t connecting to Wi-Fi, or has issues with playback, “ Swann camera Troubleshooting – Problems and Solutions with Swann security cameras” got your back.

Swann camera not working: How to Fix

If your Swann camera isn’t turning on, check the wiring or battery. If it’s offline or has hampered function, disconnect the cameras, disconnect the power supply, and then restart to see if that fixes the problem. Your camera can also stop working if it’s overheated. Cool it down and try again later.

If worse comes to worst, your Swann camera might be “bricked” or rendered completely broken and non-functioning. If it’s still in warranty, you can get it replaced for free or at least get a discount for a replacement.

See More :

• Swann device Password Reset for all model
• How to Install SwannView Link
• SWANN LATEST FIRMWARE UPDATES

Swann camera not recording: How to Fix

If your Swann cam is not recording, it might be because recording is disabled. Go to “Main Menu” the select record. Fix “Record Setup” and “Motion Setup”. You can also set up the “Record Schedule” too.

Check “Motion Setup” to see if that’s the reason why your camera isn’t recording (it only records when it detects motion).

You can also connect one camera only to your DVR or NVR to see if that fixes the recording issues. You can setup an isolation test, cross-check the camera and cable, and interpret the results to narrow down the issue.

Swann camera not connecting: How to Fix

Check your router and make sure the Wi-Fi password entered is correct. Sometimes, your Swann camera might unsuccessfully establish connection with your router simply because you misread a character or capitalized the wrong letter (it’s case-sensitive).

The cam could also be out of coverage area of the router. Make sure the router and the camera(s) are close to one another to ensure a smooth connection.

If the camera is still have issues with Wi-Fi connection, reset or power-cycle your router and try again. It might be an ISP problem. If you believe the camera is in error, you can reset it back to factory settings using the recommendation outlined below.

Swann playback not working: How to Fix

To playback a video, tap the “Playback” icon, then the “Camera” icon, and then set a start and end date and time. You can also search recordings on the recorder below the calendar then tap “Start Playback”.

Sometimes, when you attempt to playback videos, you get blue lines to show it was recorded but get an “open failed” error message when you attempt to play it. This could be caused by bad configurations, lack of storage space, corrupted video files, and failing DVR components.

This could also root from the latest software update. It mostly affects iPhone users but even Android users are affected. Contact a Swann technician or consider replacement if the problem consists.

Swann camera black screen: How to Fix

Some Swann cam users experience CCTV cam black screen or a blank video at night. This might mean the camera lacks infrared night vision, especially if it continues to record and works fine during the daytime or if you put a lamp or light source where it’s supposed to record things.

Maybe you simply forgot to turn the IR on. Fix this by checking camera settings and enabling the infrared light. If that’s not the case, then the infrared night vision camera might lack an IR cut filter.

It could also have a faulty IR sensor. Either way, you might need to have the device fixed by a technician or replaced altogether depending on the severity of the damage or the state of its warranty.

Off-warranty products might require some repair and finagling from third-party repairmen but this means it’s now outside the jurisdiction of Swann.

How to reset Swann camera?

To reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, here’s how to go about it. Locate the reset button. You might need to use a reset key or a pin in order to press it for 10 seconds to start the reset process.

Disconnect the camera from the NVR first before resetting it. You’ll also need to remove it from the PoE switch or power adapter to turn it off completely. Some devices require a pin or cable key to access the small reset button.

FAQs – Frequently Asked Questions

Here are the most frequently asked questions in regards to the Swann cam.

Where is reset button on Swann camera?

On most Swann cams, the reset button is found on the bottom of the device. However, this might vary depending on the model. This button typically requires a needle or pin to push until you hear a click sound. You need to hold the button for 10 seconds to reset the device.

How to find Swann IP camera default password?

The default all-access admin password for Swann is “12345” on the username “admin”. To reset the password for cameras, NVRs, or DVRs, you might need to get the MAC address by downloading some sort of app.

Alternatively, you can reset the camera to default settings by pushing the pin-sized reset button for 10 seconds in order to get the default password back.

Swann DVR default password: How do I find my Swann DVR password?

If “12345” is not the password being used by NVR’s “admin” account and you’ve forgotten what the password is, reset it by downloading and installing the HomeSafe Config Tool first. Open the app, click on your device’s IP address, and note the MAC address.

Now, you can go to the login screen of the DVR, click on “Forgot Password”, and enter the MAC address provided to you by HomeSafe. Click “OK” when you’re done then set a new password.

Why have my Swann cameras stopped working?

You should check first that your camera power supply (or supplies) are properly connected to a wall socket or power strip. If you do have the power supply connected to a power strip, try a wall socket just in case the power strip is faulty or is a specialised unit that doesn’t have all the sockets active at all times.

How do I reset my Swann camera?

Disconnect the camera from the NVR (or from a PoE switch or a power adapter) to turn it off completely. Press and hold the reset button. While holding down the reset button, plug the camera back to the NVR (or to the PoE switch or a power adapter) and continue holding down the reset for 30 seconds, then release.

Why is my security camera black screen?

Some users experience CCTV camera black screen or video going black at night, it’s likely that the camera lacks infrared night vision, or the IR night vision camera doesn’t have an IR cut filter or a faulty IR sensor, or you simply forget to turn the IR on. Quick Fixes: Check camera settings to make sure the IR is on.

How do I get my Swann cameras back online?

All you need to do to get back online is to re-register the camera. Follow the steps below:First, go into the home interface (this is the screen it goes to when you start the app) and tap the “Camera” button on the bottom. On the next screen, tap the camera where it says “Camera is Offline”.

How long do Swann security cameras last?

Unfortunately, details aren’t provided for how long the Lithium Ion battery will last on a single charge, but it’s likely to be around 8-10 weeks based on our use. Obviously, if it’s not practical to take the device down every couple of months, then it may be worth investing in the solar panel accessory as well.

Why is the blue light flashing on my Swann DVR?

The first time you power up your camera, the camera LED will be blinking blue to indicate pairing mode.

Why does my security camera keep going offline?

Security cameras go offline for three main reasons: power outages, loss of internet, or failure of the camera’s components (broken parts or wires). Knowing some quick troubleshooting tips will help you get your camera back up and running in no-time.

What happens if you unplug a security camera?

When your house, the cameras won’t record. When you are away from the home, the cameras record. They’ll still be “working” but not recording.

What to do if all cameras display no image on the DVR monitor?

Is this an existing camera that was working and at some point had video loss? Follow these troubleshooting steps.

1. Test Your Power Supply.
2. Check Power Supply Box Fuses.
3. Test Camera on a Different DVR Port.
4. Use a Test Monitor.
5. Use a Test Cable and Spare Power Supply.

Why is my Swann security camera not connecting?

Make sure that the connection is successful by checking your router and ensuring that your Wi-Fi password is correct. If the camera is still having issues connecting to Wi-Fi, reset the router and try again once it’s back up.

Why does my EUFY camera keep going offline?

Your Eufy camera goes offline if the battery has run out of charge, has lost connection to the HomeBase and Wi-Fi, or you need to update your Eufy app. You should check your battery and check the Wi-Fi settings to ensure that they are working correctly or reboot your camera to solve the problem.

Is Swann a Chinese company?

Swann has always been a leader. From humble beginnings in Melbourne, Australia the business now has offices in the USA, Canada, Australia, UK, Hong Kong and China and a presence in over 40 countries on 6 continents.

Can Swann cameras be hacked?

A popular wireless security camera designed to safeguard businesses and homes was vulnerable to a spying hack. The flaw meant it was possible to hijack video and audio streamed from other people’s properties by making a minor tweak to Swann Security’s app.

Are Swann 4k cameras any good?

The quality of the cameras are excellent. They feel, look and operate great. Simple setup and easy to use.

What does the blue light on my DVR mean?

The blue light indicates that the DVR (or other receiver) is outputting an HD signal. It could be the HDMI negotiation with your new TV causes it to stay on when the TV is off. If it’s too bright for you, a small piece of opaque tape is recommended.

What does it mean when Blink camera flashes red?

The Blink Video Doorbell flashes a red LED on the ring surrounding the doorbell button when it is seeking connection. During setup, and change of system or Wi-Fi, the red LED shows if the doorbell is ready to connect. If the red LED is not flashing as expected, remove one battery for five seconds and replace it.

What does a blue light mean on a camera?

LED setup reference guide

A flashing blue light on a security camera means you are ready for the WiFi protected setup.

Why do my wireless cameras keep disconnecting?

There are two main reasons that a camera may lose WiFi connection. It may be installed too far from your WiFi router, or it may not have sufficient bandwidth on your WiFi. Please contact our customer support for help in diagnosing this issue and confirming the cause.

Why won’t my security camera connect to my Wi-Fi?

Hold your phone in the location of your camera and check the number of dashed Wi-Fi coverage on your phone. If the connection is poor, if possible, reduce the distance between the camera and your Wi-Fi router. Consider a wired installation or consult your internet provider for solutions.

Why does my IP camera lost connection?

Network Conditions

Surveillance Station may lose connection to your camera when the Internet connection is poor or if changes are made to bandwidth, firewall, or IP address settings.

How do I disable Swann camera?

How do I disable Swann camera?

1. Yea, it’s possible to turn off the INTCAM manually.
2. Try this procedure, using the button on the back of the cam –
3. Press and hold the Pair button for 30 seconds.
4. To turn it back on, just press the Pair button for a second, Don’t hold too long or it’ll go into pairing mode.

Will DVR still record if unplugged?

The Cloud will continue to record your set programs while the physical DVR is unplugged. You are also correct that if your additional TV boxes are unplugged, this will not affect your planned recordings.

How do I stop my security camera from being unplugged?

Indoor cameras

1. Run your camera’s power cable behind furniture or shelving so that it’s harder to spot and unplug.
2. Install cable clips to help keep the power cord attached to the wall. Check your local hardware store for availability.

How do you troubleshoot a security camera?

How do you troubleshoot a security camera?

1. Know your login details.
2. Check the power source (most cameras are PoE)
3. Check to see if cameras work from inside or outside the network.
4. Check the cabling.
5. Reboot the system.
6. Check for IP conflict.
7. Check ARP tables.
8. Update software & firmware.

Conclusion

Even though Swann isn’t as well-known as Ring, Arlo, or Nest, it has a significant share of the Wi-Fi cam market because it caters to a significant niche. Many people are curious how to troubleshoot this camera because they’re loyal Swann customers.

There’s great demand to know how to make sure their Swann devices work and operate smoothly. They also wish to know whether their Swann is broken or fixable in some DIY way.

How to Connect Swann Camera?

If you wish to learn how to connect your Swann cam to Wi-Fi, to your phone, to your TV, to your laptop, to your MacBook, to Alexa, to the Internet, and so forth, you’ve come to the correct guide.

People are curious about the Swann camera because it provides a dependable and affordable alternative to your Ring cams, Arlo cams, and Nest cams. It does everything those cams could do in terms of Wi-Fi-based and app-based operation but in a format much closer to CCTVs.

It’s this dependability that Swann got a loyal consumer base who’d read articles like this about “How to connect Swann camera?” and whatnot. So let’s discuss how to connect the smart cam to different devices already!

How to connect the Swann camera to Wi-Fi?

In order to connect your Swann Wi-Fi or IP cam to Wi-Fi, you need to pair it up with your Swan Security app.

• Go to the Menu: To do so, tap the menu on the upper-left corner of the screen, then select “Pair Device”. Afterwards, tap “Start”.
• Scan QR Code: Attached to your camera is a QR code sticker. Have your smartphone scan that. If you don’t have the QR code, tap “Manual Pair” and get the MAC address above the serial number of your cam.
• Enter Wi-Fi Password: Now you can enter the Wi-Fi password and tap “Next”. Enter a camera name then tap “Next”. Set the camera into “Pairing Mode” by pressing and holding the rest or pair button until the LED blinks blue. Now tap “Next”. Then tap “Start”.
• Congratulations Message: If your cam successfully connected to Wi-Fi, you’ll see an overview on the app. After that’s done, tap “Next”. You’ll get a “Congratulations!” message once setup is complete.

How to connect Swann security cameras to Phones? (iPhone, iPad, Android)

Remember the section above, where you had to download an app and scan a QR code via the app in order to pair up your camera with your phone (whether it’s an Android, iPad, or iPhone)? That’s how you connect your mobile device to your Swann cam.

Get SAFE by Swann for Android devices, SwannView Plus for iOS devices, and SwannCloud for iPad and Android tablets. Swann Security App and SwannView Link can be used for multiple devices.

Finally, download HomeSafe View for desktop PCs doing NVR/DVR remote viewing and AlwaysSafe for NVW-485, NVW-490 & SWWHD-PTCAM Cameras.

See more:

How to connect the Swann camera to the TV?

You can hook up your Swann cam to your TV using the Digital Video Recorder (DVR). It has a hard disk of your recorded footage that a modern smart TV or flatscreen TV with an HDMI connection should be able to read and review videos with.

You can also connect Swann cam to your FireTV by first connecting the Swann cam to Alexa (more on this below).

How to connect Swann camera to Laptop, Macbook?

Download the HomeSafe View for desktop PCs in order to connect your Swann Camera to your MacBook or Laptop. To view Swann cam on your Windows PC, launch the Device Configuration Tool and have it detect the camera and NVR (Network Video Recorder).

Any cameras directly connected to the NVR won’t be shown. The cam’s IP address should be visible here.  Click on it like a link to launch Internet Explorer and view it from there.

How to connect the Swann camera to Alexa?

Open the Amazon Alex app. Click the three lines icon on the upper-left corner of the screen. Select “Skills and Games” tab. Search for the “Swann Skill”. Select the skill then login to your Swann account.  Press “Done” and then select “Discover Devices”.

The new Alexa Skill should then detect your Swann cams and have them listed on the “Devices” tab. Amazon Alexa works with Swann cameras to stream live camera video to your Echo Spot, Echo Show, or 4K Fire TV.

See more here:

How to connect Swann DVR to the Internet?

In order to connect your Swann DVR to the Internet, you need to first connect the DVR with your phone or tablet care of SwannLink. From there, it should have the ability to link to the Internet by proxy.

SwannLink connects systems care of peer-to-peer technology. Just scan your ID number or QR code to SwannLink in order for it to directly connect your smart devices to your DVR via the cloud, with the Swann DVR verifying the ID of your smart device as well as the username and password of the Wi-Fi.

FAQs – Frequently Asked Questions

Here is the most frequently asked questions section of this guide.

Why is my Swann camera not connecting?

Your ISP or router might have a bad Internet connection. Reset or power-cycle the router to get it back online. If the issue persists, contact your ISP for more details. Or maybe your cam is out of the router’s coverage area. Make sure they’re both near one another for best results.

Finally, check the Wi-Fi password. Make sure this case-sensitive password has been entered correctly when prompted by your app.

How do I get my Swann cameras back online?

Enter the Wi-Fi password again and make sure it’s correctly entered since it’s case-sensitive. Put your cam nearer the router. Reset the router and make sure your ISP is providing you with a solid Internet connection.

If the camera itself is failing to connect to a perfectly fine Wi-Fi, you might need to troubleshoot the cam, its connection to the app, its connection to the NVR or DVR, and so forth. You might need to reset it to factory settings altogether.

How do you reset a Swann security camera?

To reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, locate the small reset button (usually found on the underside of the device) and press it with a reset key, needle, or pin for about 10 seconds. Before doing a reset, disconnect the camera from the NVR and PoE switch.

See more: https://support.swann.com/s/article/tAM37IZ5qr

What app do I use for Swann security cameras?

The Swann Security App manages all of your Swann cameras in one central hub. The HomeSafe View app for the PC or Mac is the desktop program for remote viewing of NVRs and DVRs.

AlwaysSafe is the app for NVW-485, NVW-490 & SWWHD-PTCAM Cameras. You can also download SAFE by Swann for Android devices, SwannView Plus for iOS devices, SwannView Link for multiple devices, and SwannCloud for iPad and Android tablets.

How to access Swann DVR from the computer?

To view Swann on PC, You can see this post: https://securitycamcenter.com/view-swann-cameras-homesafe-view-software/

Conclusion

Hopefully, this guide has shown you everything you need to know about Swann cameras when it comes to setting them up, connecting them to different devices, and troubleshooting any errors you might encounter when operating them.

How to Reset Swann Camera?

You’ve reset one camera you’ve reset them all, right? Well, kind of. In the case of the Swann Camera or any other Wi-Fi security camera out there, it’s some variation of finding the reset button, waiting for the light to change, and then you’re done.

The Swann brand claims to produce some of the world’s best value security solutions that also offer the most intuitive controls and the smartest of features. They intend to empower you, the consumer when it comes to their quality products like their Wi-Fi or smart device cameras.

Although they’re not as well-known as Ring, Arlo, or Blink, they have their own market share and niche to cater to. This is why so many people are curious about how to reset the Swann camera. It’s not exactly the same as resetting cameras from Ring and Arlo.

How to Reset Swann Camera

In regards to how to reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, here’s the nitty-gritty. There’s an extra cable for the models above that isn’t a connector but a reset button. It looks like a reset key to use on a keyhole or pinhole to prevent accidental resets.

When resetting the Swann Cam to factory settings, you need to disconnect it from the NVR first. Or from its power adapter or PoE switch. This will turn it off completely. Now locate the reset button press and hold it. Some devices might require a cable key or pin to access the button.

Reconnect While Resetting Then Disconnect Afterwards

While holding the button down, plug the camera back to the NVR, PoE switch, or power adapter. Continue holding it down for about 30 seconds before releasing. At this point, disconnect the camera again to turn it off completely.

This should reset your cam to factory settings. Unlike other Wi-Fi camera models, Swann Cams make it more complicated to do a reset to avoid accidental resets, like you accidentally pressing the button or inserting a pin into the reset pinhole when you have no intention to reset to factory settings.

Why Do You Need to Reset the Swann Camera?

Sometimes, the Swann Cam—like any other sophisticated piece of electronics, such as your laptop, smartphone, and tablet—can encounter a glitch or an error that keeps it from properly connecting to your Wi-Fi, using its motion alerts, or uploading its footage to the cloud (if you paid for the service).

You can do a host of things to troubleshoot such errors, including power cycling the device like a wayward router or fixing your router itself to re-establish your Wi-Fi connection if the problem isn’t with the Swann hardware itself.

If push comes to shove and none of those tips work, you can do a hard reset to factory settings (the settings right off of the box or the factory line) to get it working back to normal. You’ll still need to put back your customizations afterwards though.

The History of Swann 101

Swann traces its roots back to Melbourne, Australia. It eventually grew from its humble beginnings, with it now being an international or multinational company with offices in the United Kingdom, the United States of America, Canada, Hong Kong, and Mainland China as well as Australia.

It even has a presence in over 6 continents and 40 countries. What separates Swann from other security companies riding the Wi-Fi cam thread is that it’s a pioneer in the field of Do-It-Yourself (DIY) security with its often imitated features taken from many of its products.

It has doubtlessly done its part in making households and neighborhoods safer compared to before, when the only cameras regular consumers could afford were Nanny Cams and Baby Cams.

Swann’s Membership with the Infinova Group

At present, Swann serves as an Infinova Group member, thus providing major commercial institutions and startup businesses alike with enhanced security device production through better manufacturing abilities, cutting-edge research and development, and state-of-the-art innovations.

They’re at the forefront of networking and security solutions plus they’re not limited to the video doorbell or Wi-Fi security camera market like the Amazon-backed Ring and Blink camera lines. They’ve also expanded their international network access thanks to their Infinova Group backing.

They’re specifically dependable when it comes to making the one-app ecosystem standard work superbly in their models of smart devices, as opposed to others that use multiple apps or one app per camera model.

Swann’s Focus on Crime Prevention

While other companies would rather turn their Wi-Fi camera offerings into Swiss Army Knives of functionality that assist in making the Smart Home future of the 21^st Century a reality, Swann has established its market presence with a different tactic.

They’re more about giving consumers true security, which means they have more of a focus on crime prevention. They provide their cameras with alarms and direct lines to the police for emergencies instead of turning their camera into the next smartphone with non-essential features.

This is also why most Swann cameras offers two-way talk, sirens, alarms, sensor lighting, motion sensors, night vision, and more. This deters not only midnight prowlers and burglars but also package thieves and neighborhood brats.

Swann’s Enforcer Cameras

Swann’s Enforcer Cameras take crime deterrence to another level by using True Detect detection sensors that detect heat, motion, and people. The people detection in particular keeps down power usage and false alarms involving strays and wildlife like cats, chipmunks, birds, and raccoons.

When triggered, True Detect activates the alarms and chimes with all its trimmings. You’ll get mobile alerts, spotlights, flashing lights, video recordings, and more as though you’ve tripped the museum alarms that alert the security guards (or your closest neighbors).

Many of Swann’s more sophisticated inventions include vehicle and pet detection, face recognition, and the peace of mind that your home is protected through cloud and local recordings. This is why it has camera reset included to deal with software errors from all those settings.

Things of Note

We believe that the Swann Camera allows customers to protect and stay connected to their home and/or businesses no matter the circumstances through best-value and intuitive design. This is reflected upon the ease by which you can reset their cameras.

This proves that Swann is one of the global leaders in security monitoring with consumer electronics or smart devices as well as security-centric solutions for smart homes and commercial establishments of the present and the future. What more can you ask for a renowned company with affordable wares?

Have you lost the H.264 DVR’s password reset and don’t know how to recover it?

Well-known brand such as Samsung, Bosch and Pelco have technical support team

If your DVR has the internal chip manufactured by Hisilicon, there is a great chance that the DVR password generator will work, depending on the model and year it was manufactured. See the chart below:

Make sure the clock has returned to the old date before attempting to use the password.

This type of battery is fixed to the board. Use tweezers with the tip on the top of the battery holder and the other end on the bottom, close the contact for about 1 to 2 minutes to reset the DVR.

AVTECH AVC-704H Jumper

AVTECH AVC-706H Jumper

Camera Firmware Update for V8 NVRs

Guide on how to update IP camera firmware of V8 NVRs

Read This : Reset password on H264 DVR All Brands

READ THIS FIRST

1. V8 NVRs are NVR-8580, 8580RN, 8780, and 8780RN with Software version starting with V8
2. NVR must have the latest firmware. To check, visit How to do OTA update? first.
3. Update one camera at a time to decrease the possibility of incomplete updates. Simply retry on the cameras that were incomplete and they should complete on the second attempt.
4. Check the live feed after each update to confirm if the camera is still working. In the event that you noticed an issue, STOP updating the rest.

Prepare the following:

1. Computer with internet connection
2. USB flashdrive (preferably 32GB or below)
3. Mouse and monitor connected to the NVR

Quick install steps

Download the correct image file:

1. Download the firmware based on the camera’s model number:
   1. NHD-865 (MSB or MSFB) or NHD-866MSD – click HERE  to download
   2. NHD-885 (MSB or MSFB) or NHD-886MSD – click HERE to download
   3. NHD-887 (MSB or MSFB) or NHD-888MSD – click HERE  to download
   4. NHD-900 (BE or DE) – click HERE to download
2. Copy the files to a (preferably clean) USB memory stick.

Apply the firmware to the cameras:

1. Insert the USB memory stick into one of the recorder’s USB ports.
2. Open the menu on the recorder and proceed to Advanced > Maintain.
3. In the Maintain tab, click on IP Cam Upgrade button.
   
4. On the preparation screen, select the new firmware file (.sw) for each channel from the USB stick.
   
5. Once firmware file is specified, choose a Channel where firmware will be applied, then click OK.
   
   
6. When firmware update is completed, you will receive this prompt:
   
7. Repeat this step with the old firmware file for any cameras that failed

DVR USB Firmware Update

Updating via USB direct to the 8-5680A recorder

NOTE: If you’re unit’s model number is DVR8-5680 (no suffix), follow this article instead: DVR8-5680 USB Firmware Update

If you’re unit’s model number is DVR8-5680RN, follow this article instead: DVR8-5680RN USB Firmware Update

If you’re unit’s model number is DVR8-5680X, follow this article instead: DVR8-5680X USB Firmware Update   No suffix
   With suffix

To check what is your current firmware, access the DVR’s Menu then go to System > Information and look for the Software Version. For a DVR8-5680A, the latest Software Version is v8.1.0-20221223

Before you try the following procedure, read this article first: How to do OTA update?

If you are unable to use the automatic update service to update the recorder, you can use the following procedure to update manually.

1. Prepare a FAT32 flash drive or USB – it needs to be on FAT32 for it to be read; there is no need for an external HDD as the files are small.
2. Download the firmware file HERE and save it to your flash drive.
3. Unplug the Ethernet cable connected to the DVR then reboot.
4. Insert the flash drive to your DVR.
5. Access the Menu and go to Advanced > Maintain then click on Upgrade.
6. Select the file: D2108ST_V210609V210625V210709V211223V211223V211223V211014.sw and click OK.
7. A confirmation window will appear, click on OK again.
8. DVR will start to update. Make sure not to unplug the USB or turn off the DVR while it is updating.

NOTE²: If updating the firmware via Menu fails, use Swann Security VMS on a Windows computer. Follow Firmware update for V8 recorders via Swann Security VMS (Windows)

NVR USB Firmware Update

Updating via USB direct to the 8-8780 recorder

NOTE: If your unit’s model number is NVR8-8780RN, follow this article instead: NVR8-8780RN USB Firmware Updates   No suffix
   With suffix

To check what is your current firmware, access the NVR’s Menu then go to System > Information and look for the Software Version. For a NVR8-8780, the latest Software Version is v8.1.0-20211020

Before you try the following procedure, read this article first: How to do OTA update?

If you are unable to use the automatic update service to update the recorder, you can use the following procedure to update manually.

1. Prepare a FAT32 flash drive or USB – it needs to be on FAT32 for it to be read; there is no need for an external HDD as the files are small.
2. Download the firmware file HERE and save it to your flash drive.
3. Unplug the Ethernet cable connected to the NVR then reboot.
4. Insert the flash drive to your NVR.
5. Access the Menu and go to Advanced > Maintain then click on Upgrade.
6. Select the file: N4XXX_V210825V210805V210817V211020V211020V211020V211014_W.sw and click OK.
7. A confirmation window will appear, click on OK again.
8. NVR will start to update. Make sure not to unplug the USB or turn off the NVR while it is updating.

NOTE²: If updating the firmware via Menu fails, use Swann Security VMS on a Windows computer. Follow Firmware update for V8 recorders via Swann Security VMS (Windows)

All Files Relase Firmware Download : Swann Firmwre Relase

• DVR8-4680X USB Firmware Update

  Updating via USB direct to the 8-4680X recorder

  343 Views•07/03/2022•Knowledge

• DVR4-4480V USB Firmware Update

  Updating via USB direct to the 4-4480V recorder

  1471 Views•17/02/2022•Knowledge

• DVR4-4480G USB Firmware Update

  Updating via USB direct to the 4-4480G recorder

  624 Views•17/02/2022•Knowledge

• DVR4-4480RN USB Firmware Update

  Updating via USB direct to the 4-4480RN recorder

  68 Views•17/02/2022•Knowledge

• DVR8-5680 USB Firmware Update

  Updating via USB direct to the 8-5680 recorder

  1708 Views•17/02/2022•Knowledge

• DVR4-5580G USB Firmware Update

  Updating via USB direct to the 4-5580G recorder

  535 Views•16/02/2022•Knowledge

• DVR4-5680 USB Firmware Update

  Updating via USB direct to the 4-5680 recorder

  374 Views•16/02/2022•Knowledge

• DVR8-4680RN USB Firmware Update

  Updating via USB direct to the 8-4680RN recorder

  604 Views•16/02/2022•Knowledge

• DVR8-4480RN USB Firmware Update

  Updating via USB direct to the 8-4480RN recorder

  33 Views•16/02/2022•Knowledge

• DVR4-5680RN USB Firmware Update

  Updating via USB direct to the 4-5680RN recorder

  106 Views•16/02/2022•Knowledge

• DVR4-5580RN USB Firmware Update

  Updating via USB direct to the 5-5580RN recorder

  28 Views•16/02/2022•Knowledge

• DVR4-4680RN USB Firmware Update

  Updating via USB direct to the 4-4680RN recorder

  252 Views•16/02/2022•Knowledge

• DVR8-4685RN USB Firmware Update

  Updating via USB direct to the 8-4685RN recorder

  14 Views•16/02/2022•Knowledge

• DVR4-4685RN USB Firmware Update

  Updating via USB direct to the 4-4685RN recorder

  10 Views•16/02/2022•Knowledge

• DVR8-4580RN USB Firmware Update

  Updating via USB direct to the 8-4580RN recorder

  121 Views•16/02/2022•Knowledge

• DVR8-4685 USB Firmware Update

  Updating via USB direct to the 8-4685 recorder

  160 Views•16/02/2022•Knowledge

• DVR8-4680 USB Firmware Update

  Updating via USB direct to the 8-4680 recorder

  3548 Views•16/02/2022•Knowledge

• DVR8-4480G USB Firmware Update

  Updating via USB direct to the 8-4480G recorder

  170 Views•16/02/2022•Knowledge

• DVR8-4580G USB Firmware Update

  Updating via USB direct to the 8-4580G recorder

  1228 Views•16/02/2022•Knowledge

• DVR4-4680 USB Firmware Update

  Updating via USB direct to the 4-4680 recorder

  1032 Views•16/02/2022•Knowledge

• DVR4-4685 USB Firmware Update

  Updating via USB direct to the 4-4685 recorder

  348 Views•16/02/2022•Knowledge

• DVR4-4580G USB Firmware Update

  Updating via USB direct to the 4-4580G recorder

  1111 Views•16/02/2022•Knowledge

• DVR8-4580V USB Firmware Update

  Updating via USB direct to the 8-4580V recorder

  3976 Views•16/02/2022•Knowledge

• DVR8-4480V USB Firmware Update

  Updating via USB direct to the 8-4480V recorder

  656 Views•16/02/2022•Knowledge

• DVR4-4580V USB Firmware Update

  Updating via USB direct to the 4-4580V recorder

  2577 Views•16/02/2022•Knowledge

• DVR8-5580RN USB Firmware Update

  Updating via USB direct to the 8-5580RN recorder

  74 Views•16/02/2022•Knowledge

• DVR8-5680RN USB Firmware Update

  Updating via USB direct to the 8-5680RN recorder

  1339 Views•16/02/2022•Knowledge

• DVR8-5580G USB Firmware Update

  Updating via USB direct to the 8-5580G recorder

  1294 Views•15/02/2022•Knowledge

• DVR8-5580A USB Firmware Update

  Updating via USB direct to the 8-5580A recorder

  71 Views•15/02/2022•Knowledge

• DVR4-4580RN USB Firmware Update

  Updating via USB direct to the 4-4580RN recorder

  126 Views•15/02/2022•Knowledge

• DVR16-4580G USB Firmware Update

  Updating via USB direct to the 16-4580G recorder

  242 Views•15/02/2022•Knowledge

• NVR8-8580 USB Firmware Update

  Updating via USB direct to the 8-8580 recorder

  25201 Views•15/02/2022•Knowledge

• NVR8-8780 USB Firmware Update

  Updating via USB direct to the 8-8780 recorder

  2709 Views•15/02/2022•Knowledge

• Camera Firmware Update for V8 NVRs

  Guide on how to update IP camera firmware of V8 NVRs

  19483 Views•10/02/2022•Knowledge

• DVR8-5680A USB Firmware Update

  Updating via USB direct to the 8-5680A recorder

  190 Views•10/02/2022•Knowledge

• DVR8-4680A USB Firmware Update

  Updating via USB direct to the 8-4680A recorder

  803 Views•10/02/2022•Knowledge

• DVR4-5680XN USB Firmware Update

  Updating via USB direct to the 4-5680XN recorder

  15 Views•09/02/2022•Knowledge

• DVR8-5680X USB Firmware Update

  Updating via USB direct to the 8-5680X recorder

  225 Views•09/02/2022•Knowledge

• DVR4-4680XN USB Firmware Update

  Updating via USB direct to the 4-4680XN recorder

  41 Views•09/02/2022•Knowledge

• DVR8-4680XN USB Firmware Update

  Updating via USB direct to the 8-4680XN recorder

  139 Views•09/02/2022•Knowledge

• DVR4-4980V USB Firmware Update

  Updating via USB direct to the 4-4980V recorder

  1303 Views•09/02/2022•Knowledge

• DVR16-5580G USB Firmware Update

  Updating via USB direct to the 16-5580G recorder

  524 Views•09/02/2022•Knowledge

• DVR16-5580 USB Firmware Update

  Updating via USB direct to the 16-5580 recorder

  887 Views•09/02/2022•Knowledge

• DVR16-4980 USB Firmware Update

  Updating via USB direct to the 16-4980 recorder

  211 Views•09/02/2022•Knowledge

• DVR16-4680 USB Firmware Update

  Updating via USB direct to the 16-4680 recorder

  211 Views•09/02/2022•Knowledge

• NVR8-8580RN USB Firmware Update

  Updating via USB direct to the 8-8580RN recorder

  1415 Views•31/01/2022•Knowledge

• DVR8-5580 USB Firmware Update

  Updating via USB direct to the 8-5580 recorder

  3635 Views•31/01/2022•Knowledge

• DVR16-5580G2 USB Firmware Update

  Updating via USB direct to the 16-5580G2 recorder

  19 Views•31/01/2022•Knowledge

• DVR4-5580 USB Firmware Update

  Updating via USB direct to the 4-5580 recorder

  458 Views•27/01/2022•Knowledge

• DVR8-4980 USB Firmware Update

  Updating via USB direct to the 8-4980 recorder

  2741 Views•27/01/2022•Knowledge

• DVR16-4580V USB Firmware Update

  Updating via USB direct to the 16-4580V recorder

  729 Views•27/01/2022•Knowledge

• DVR16-4680RN USB Firmware Update

  Updating via USB direct to the 16-4680RN recorder

  124 Views•20/01/2022•Knowledge

• How to update the firmware of your Swanncloud camera through the Swanncloud app?

  SwannCloud servers will get a major upgrade on Jan 25, 2022. Cameras that have older firmware will cease to operate afterwards.

  13826 Views•17/01/2022•Knowledge

• SwannCloud Camera Firmware Release

  SwannCloud servers will get a major upgrade on Jan 25, 2022. Cameras that have older firmware will cease to operate afterwards.

  12221 Views•17/01/2022•Knowledge

• NVR8-8780RN USB Firmware Update

  Updating via USB direct to the 8-8780RN recorder

  710 Views•23/12/2021•Knowledge

• NVR16-8580RN USB Firmware Update

  Updating via USB direct to the 16-8580RN recorder

  558 Views•22/12/2021•Knowledge

• DVR16-4680A USB Firmware Update

  Updating via USB direct to the 16-4680A recorder

  332 Views•08/12/2021•Knowledge

• NVR16-8580 USB Firmware Update

  Updating via USB direct to the 16-8580 recorder

  4560 Views•07/12/2021•Knowledge

• NVR8-8580 Manual Firmware Update

  Update via USB for the 88580 recorder.

  42380 Views•18/11/2021•Knowledge

• NVR4-7000/7200 Firmware release