.

What’s Included:

Junction Box for PTZ Cameras Installation Guide.

Installation:

Warning: Install in an area that can support 3× total weight of the camera and junction box.

Note: The products mentioned and shown above are not included.

Junction Box for PTZ Cameras: Troubleshooting Guide

This article provides troubleshooting guidance for addressing issues for your AJLZ junction box for PTZ cameras.

.

I cannot fit my camera’s cable through the front of the junction box

.

My PTZ Camera has external accessories

You can install external accessories inside the junction box in the metal trays.

.

I want more room for cables in my junction box

You can make more room in the junction box by removing the metal trays inside with a Phillips head screwdriver.

.

I need to organize my cables

The included cable ties are for cable organization inside of the junction box. Manually coil your cables until the junction box outputs the desired length of wire, and then use the cable ties to keep the coil together.

Junction Box for PTZ Cameras: Frequently Asked Questions

This article answers frequently asked questions about your AJLZ junction box for PTZ cameras.

.

Setup

.

What tools do I need to install my junction box?

To install your junction box, you will only need a drill, however to customize your junction box with accessories you will need a Phillips head screwdriver.

.

How do I fit my camera’s cable through the front of my junction box?

.

Where can I install the junction box?

The outdoor junction box can be installed at any location that can support 3× total weight of the outdoor junction box and the attached camera. However the following criteria are recommended for best performance:

Location Selection:

Mounting Surface:

Other recommendations:

.

What are the benefits of the junction box?

The outdoor junction box adds protection, and aids in wire organization for your device.

.

How much weight can the junction box hold?

The outdoor junction box can carry up to 17.64 lb / 8.0 kg, which includes the weight of any of the compatible devices.

.

How do I install my junction box?

Please refer to the Installation Guide for your junction box.

.

How do I organize the cables inside the junction box?

The included cable ties are for cable organization inside of the junction box. Manually coil your cables until the junction box outputs the desired cable length, and then use the cable ties to keep the coil together.

.

General

.

What is a junction box

A junction box attatches to a device and secures its cables in a contained space. It allows for improved safety, organization, and look for a device and it’s cables. This PTZ camera junction box allows you to keep your PTZ camera’s cables, and applicable added accessories safe and secure from weather and tampering.

.

How many cables can exit or enter my junction box?

Up to 5 cables can enter or exit the junction box and plu in externally. Up to 3 cables can be weatherproofed with a cable gland.

.

What are the dimensions of the outdoor junction box?

The dimensions of the outdoor junction box are (W × D × H) 11.70 × 9.76 × 5.15” / 297.2 × 248.0 × 130.7 mm.

.

Which cameras are compatible with this product?

Please see the Compatibility Chart to find compatible cameras.

.

What is the size of the included Allen key?

The included Allen key is 5 mm.

 Outdoor Junction Box: Frequently Asked Questions

The following FAQ article answers common questions about the AJLD-1W Series – Outdoor Junction Box. Where applicable, the FAQ includes links to articles where you may find more information.

.

How do I install my E851AD camera with this product?

The E851AD camera equips a cable that exits from the bottom edge of the device, while other models equip cables that exit from the middle of the bottom side. Because of this, extra care must be taken to attach the outdoor junction box to the E851AD camera. Please follow the following steps for proper installation of your camera and outdoor junction box.

Note: Do not remove the dome cover in humid or dusty environments and always wash your hands before handling your camera.

Enjoy using your new E851AD camera, with your new outdoor junction box.

.

Where can I install the outdoor junction box?

The outdoor junction box can be installed at any location that can support the entire weight of the outdoor junction box and the attached camera (up to 7.8 lbs / 3.54 kg). However the following criteria are recommended for best performance:

Other recommendations:

.

What are the benefits of the outdoor junction box?

The outdoor junction box adds protection, and aids in wire organization for your device.

.

How much weight can the outdoor junction box hold?

The outdoor junction box can carry up to 1.19 llbs / 0.54 kg, which includes the weight of any of the compatible devices.

.

What are the dimensions of the outdoor junction box?

The dimensions of the outdoor junction box are (W × D × H) 5.27 × 5.25 × 2.05” / 134 × 133.5 × 52 mm.

.

Which cameras are compatible with this product?

Please see the Compatibility Chart to find compatible cameras.

.

Understanding the Basics: What You Need to Know Before Buying

Before diving into the different types of security cameras, it’s crucial to understand some basic but important considerations that will influence your choice.

Identifying Your Security Needs

When considering the installation of a security camera system, the first step is to assess your specific needs. The requirements of a sprawling estate versus a cozy apartment differ vastly. Similarly, a retail business will have different security needs compared to a manufacturing unit. Begin by asking yourself the following questions:

Answering these questions will lay a solid foundation for your search and ensure that you don’t end up with a security camera system that’s either overkill or insufficient for your needs.

Security Camera Buying Guide and How to Choose

Considering the Location

The location where the cameras will be installed plays a pivotal role in your decision-making process. Indoor cameras differ significantly from outdoor cameras, particularly in terms of durability and weather resistance. If you’re considering outdoor surveillance, ensure the cameras are weatherproof and have adequate night vision capabilities.

Exploring Security Camera Technologies

When choosing a security camera, it is critical to understand the differences and similarities between IP security cameras and HD over coax security cameras to select the right type for specific needs.

What are IP Security Cameras?

IP (Internet Protocol) security cameras are digital video cameras that use networks to transmit image data and control signals over an IP network. These cameras can be directly accessed from a network connection, making them highly versatile for a variety of settings.

Advantages of IP Security Cameras

High Resolution: IP cameras are known for high-resolution images, which can go up to 4K resolution, allowing for clearer and more detailed images.

Scalability: They are highly scalable as one can easily add more cameras to the existing network without significant infrastructure changes.

Remote Accessibility: IP cameras can be accessed and controlled remotely, making it possible to monitor footage from anywhere in the world via the internet.

Disadvantages of IP Security Cameras

Cost Factors: They tend to be more expensive than other types, both in terms of initial setup and maintenance.

Network Dependency: These cameras require a stable network connection, which can be a limitation in areas with poor connectivity.

What are HD Over Coax Security Cameras?

HD over coax security cameras transmit high-definition video over coaxial cable. These cameras are an upgrade from the traditional analog CCTV systems, providing better resolution and clarity without the need for new cabling infrastructure.

Advantages of HD Over Coax Security Cameras

Cost-effectiveness: Generally less expensive than IP cameras and utilize existing coaxial cable setups.

Ease of Installation: They are relatively easy to install, especially if replacing existing analog systems.

Reliability: Less dependent on network bandwidth and do not suffer from network-induced lag.

Disadvantages of HD Over Coax Security Cameras

Limited Resolution: While improved over analog cameras, their resolution does not compare to the high levels achievable by IP cameras.

Scalability Issues: Adding more cameras often requires additional DVRs (Digital Video Recorders), which can complicate the system.

Comparing Video Quality and Resolution

When it comes to resolution, IP cameras generally offer more with options going up to 4K, whereas HD over coax typically maxes out at 1080p. This makes IP cameras a better choice for scenarios where detail is critical.

Comparing the Cost Implications

IP cameras have a higher upfront cost primarily due to the need for networking equipment and possibly, higher quality cabling. However, HD over coax cameras often involve less expensive equipment but might incur more costs if extensive cabling is needed.

Remote Access Capabilities

Both IP camera systems and HD over coax camera systems excel in remote access as they can be configured for view from any location thru PC, cell, or tablet through the internet. 

Use Case Analysis

For large, expanding facilities or highly detailed surveillance needs, IP cameras would be more suitable. In contrast, HD over coax cameras are well-suited for smaller setups or where budget constraints are significant.

Future Trends in Security Cameras

The future likely holds further enhancements in camera resolution and network capabilities for IP cameras, and continuous integration of advanced analytics. HD over coax might see improvements in compression and transmission to allow for higher resolutions.

Both IP and HD over coax security cameras offer distinct advantages and disadvantages. Your choice should depend on your specific needs, budget, and desired scalability. Understanding these aspects will guide you in choosing the most suitable type.

Exploring Types of Security Cameras

With a basic understanding of what to consider before purchasing, let’s delve into the most popular types of security cameras available on the market.

Dome Cameras

Dome cameras are named for their dome-like shape, making them more discreet than other types. They’re excellent for indoor use, especially in retail or commercial settings, where they can blend in with the decor while providing a wide viewing angle.  In addition, most of our dome cameras are also vandal resistant.

Bullet Cameras

Bullet cameras are long and cylindrical. They are typically used outdoors, mounted on walls or ceilings. These cameras are known for their strong night vision capabilities and long-distance viewing, making them ideal for monitoring large areas like backyards or parking lots.  Whether you need a wide angle or a zoom we have the perfext bullet security camera for you. 

Wireless vs. Wired Cameras

Another crucial consideration is whether to go for wireless or wired cameras. Wireless cameras offer flexibility in placement and are generally easier to install. However, they depend on your Wi-Fi signal’s strength and can be more susceptible to interference. On the other hand, wired cameras require a more complex installation process but provide a more stable and reliable connection, making them well-suited for extensive surveillance systems.

Smart Cameras

Smart cameras come with features like motion detection, facial recognition, and automatic alerts. These cameras not only record footage but also analyze it, sending you notifications when something out of the ordinary happens. They’re perfect for homeowners who want to stay informed about their property’s security in real time.  We also have specialty cameras such as PTZ, license plate, and fisheye cameras.

Key Features to Look For

Delving deeper into the specifics, here’s what you should look for when shopping for a security camera:

Selecting the right security camera for your home or business requires careful consideration of your specific security needs, the features you value most, and the type of camera that best suits your space. By taking the time to understand the different options available and what each offers, you can make an informed choice that ensures your property is watched over effectively. Remember, the goal is not just to deter potential intruders but to give you the confidence that comes with knowing your space is secure. Whether you opt for a dome camera for your business interior or a bullet camera for outdoor surveillance, ensuring your peace of mind is the ultimate priority.

.

Unlimited Access Anywhere, Anytime

When you combine our “Blue Line” IP Cameras with one of our compatible IP camera network video recorders you can keep an eye on your assets no matter where you are. Take advantage of the free remote viewing app to view on your cell. Use the free software to view and control you cameras on your tablet, or computer. Stay connected and have peace of mind knowing you can monitor your cameras remotely, without any additional monthly fees.

LATEST FIRMWARE UPDATES FOR YOUR DEVICE

UPDATING YOUR SECURITY CAMERA FIRMWARE

Firmware Updates

In order to do a firmware update you must first identify the EXACT model number of your DVR or NVR unit. The model number can be found on the sticker located on the bottom or side of the unit. All CCTV Security Pros model numbers begin with the prefix “CSP” (Example, CSP-XXXX). Please match your model number to the list provided below. You will also need to locate your order confirmation email to determine when the unit was purchased. Once you have identified the correct model number and firmware please continue by following the instructions below.

Blue Line IP Camera Troubleshooting v2

Upgrading Your Firmware

Please identify the correct model from the list of firmware provided below.

Please select the appropriate link and download the .bin file. Once the download is completed copy the .bin file to a USB Flash/Thumb Drive. We suggest formatting your USB drive to FAT32 before attempting the update.

**Note : Units with Build Dates of 2013 or earlier may require you to rename the file to “update.bin” before launching the upgrade.

Once the .bin file has been transferred onto your drive you can insert the USB Drive into either of the two USB ports found on your unit. One can be found on the front panel and one can be found on the rear of the unit.

Once the drive is inserted into the unit go to the following menu:

Main Menu –> Setting –> System –> Upgrade. Click Start. Find and select the .bin file you transferred to the USB Drive and Click Start.

*NOTE – On select models you will need to go to:

Main Menu–> Info –> Version –> Upgrade

The unit will now begin upgrading to the latest Firmware Revision that is available for your device. Once completed the system will reboot. After the reboot we recommend doing the following:

1) Remove the USB Drive from your system.

2) Change your passwords on your “admin” account. For assistance in altering your password please follow this link: https://www.cctvsecuritypros.com/content/pdfs/password-account-settings.pdf

.

IMPORTANT: If you are having difficulty identifying the correct firmware please email us at support@cctvsecuritypros.com with your order number and unit model number.

User Account Locked

Your system will lock itself out when you or someone else has attempted to log into your DVR

with an incorrect user/password combination more than three times within 30 minutes

When this happens you have two options.

1. Wait 30 minutes after the last failed login attempt and try again.

2. Reboot the DVR by using the rear toggle switch or by unplugging.

When the unit powers back on try and login with the default username and passwords.

Username: admin

Password: admin

or

Username: 888888

Password: 888888

If neither of these passwords get you into your system you will need to email us at

Support@CCTVSecurityPros.com

and request a Master Password. Once we can confirm your

account we will happily be able to provide you with the correct login credentials.

Please have your Order Number or DVR/NVR Model Number when requesting a Master

Password.

*Note: The DVR/NVR Model Number can be found on the Bottom or Side of your system.

.

IP Camera Harness Repair

If your connector looks like the ones below, moisture has gotten into your RJ45 connector. The number one cause of premature IP camera failure has to do with improper weatherproofing techniques. If caught early enough a simple cotton swab and rubbing alcohol will clean that connector right up! You may need to resort to some heavier duty electrical contact cleaner if the cotton swab method does not work.

If all else fails and the connector is too far gone and cleaning it will not work, you will need to perform a harness repair.

.

In order to perform the repair you will need:

.

.

1 x RJ45 Crimp Tool1 x Male RJ45  1 x Female to Female RJ45

Connector

.

1 x Your choice of weatherproofing ( Weatherproof junction box or weatherproof Female to Female connection)

.

.

Start by removing the RJ45 end off of your IP cameras harness. Be sure

.

Strip back the outside insulation to expose the internal cables.

.

Organize the cables to match the pinout of the IP camera. Slide the organized cables into the connector and crimp. All CCTV Security Pros IP cameras will use this pinout.

Connect your Female to Female RJ45 connector to check your work, you should have a functioning IP camera now that its void of all corrision.

Now that the IP camera has been repaired we still need to weatherproof this connection. It is now more vulnerable than ever!

Consider using a weatherproof junction box to make your connections in, or perhaps a weatherproof Female to Female connector.

Remember that different coupling styles exist so make sure that you are informed about how to use the coupler before you start crimping wires.

Troubleshooting Steps 4/8/16 Channel

(Cannot Find the Network Host)

To solve the error, please verify that the camera is properly plugged into the back of the system. If you unplug and re-plug it back in this should verify it is connected physically.

If the issue continues go to Main Menu > Camera > Camera List and delete the camera with the red status from the bottom list and do a Device Search to verify the camera is showing up on the top list.

If the camera does not show up this means the cable is not connecting properly, which could either mean the camera is not getting power or isn’t transmitting data. The best way to determine whether it is an issue with the Camera or Cable is to bench test the camera on a known working cable.

If it does show up but it has a different IP Address, please confirm the IP Address is in the 10.1.1.1-255 range (This is the default range of the internal Switch).

If the camera is not within the correct IP range, then the camera could need to be modified on the top list to properly connect in which you would select the camera, hit modify, type in the camera’s username and password and set the IP address to DHCP to automatically obtain an IP or statically assign the camera an IP address to match your switch range and gateway.

If the camera is on the correct range, you should be able to add it to the bottom list and it will come up with Green or Red, If Red double check the error message on the live view on the system.

If the Error says Invalid Username or Password, go back to Settings > Camera > Camera List and modify the camera at the bottom of the list and type in the correct login information.

If the error says Cannot Find the Network Host, check the IP Address is in the correct range, if it is you need to verify your cable is good by testing the camera with another known good cable or testing on a short patch cable as the cable could be experiencing packet loss.

Make sure the cable is T568B Standard and is within 100 meters (328 feet.)

Night Vision Issues

When a camera goes into night vision mode, the infrared LEDs around the lens turn on. If the video signal at nighttime or in dark locations is washed out, foggy or you see “halos” on the screen it is because the infrared LEDs are reflecting back into the camera lens.

cameras LEDs to focalize on the mounting surface and greatly reduce the Infrared distance.

Adding 3rd Party Cameras to Blue Line NVR

We always recommend using Blue Line IP cameras with our Blue Line NVRs for the easiest and most complete experience possible. However, we understand that using 3rd Party Cameras can be beneficial in some applications. This guide will explain the basics of adding a 3rd Party IP camera into your Blue Line NVR.

Information you will need to add 3rd Party Cameras.

With your camera attached to one of the PoE ports on your NVR, you’ll navigate to the camera settings from the main menu.

A 3rd Party Camera normally will not add itself, so you will need to go into the Camera List and click on Search Device. If the camera is detected, you will be able to select it and click on the Modify IP button toward the middle of the screen.

When modifying the IP address of the camera the default IP range for the PoE ports on the NVR is

10.1.1.xxx so you’ll want to make sure the camera is on the same range.

You will need to know the camera’s password to change the IP Address. Once the IP is successfully changed it should update after clicking Search Device again

Check the box to the left of the camera and click Add. Most cameras will show up with the Manufacturer as ONVIF. If they do not and show up as red, you will need to click on the edit button on the camera and change the Manufacturer to match the camera’s manufacturer, or to ONVIF if the manufacturer of the camera is not listed.

While in the modify window you can also enter the password for the camera in the password field. Once that is completed you can click OK. After a few seconds the status should change to a green icon and then you should be able to see the camera’s live view. Please keep in mind that if the Error Message says Invalid Username or Password you may need to login to the camera from the Web and setup an Onvif User for the system to login with.

If the camera is still showing offline, setting the manufacturer to PELCO can sometimes resolve the issue.

Additional 3rd Party Camera Information

DVR/NVR Rebooting

If your DVR or NVR is rebooting by itself please read the guide below.

If your DVR or NVR is rebooting once a week this is completely normal. Our DVR and NVR systems are designed to reboot once a week (Tuesday at 2AM by default).

If your DVR or NVR is rebooting more frequently you first want to check the power source of the DVR or NVR.

Be sure you are using the correct Power Source that was included with the DVR or NVR. Below are the correct power adapter specs so you can identify the correct one.

NVRCUBE = 12V, 2.0Amp NVRWIFI = 12V, 2.0Amp

LITE Series DVR = 12V, 2.0Amp

Pro Series DVR = 12V, 5.0Amp

Pro Series NVR = 3 Prong Power Cord to Power Outlet Extreme Series DVR/NVR = 3 Prong Power Cord to Power Outlet

If you can confirm you are using the correct Power Adapter you may need to double check the outlet you are plugged into. Try an alternate outlet and eliminate any Battery Backup Power Supplies for test purposes.

If the power source is not causing the reboot cycle it could be related to the internal hard drive. To check this out please continue reading.

First you will need to Power Off the DVR. We suggest powering the system down from the Power Switch on the rear of the system or by simply unplugging the Power Cable.

Once the system has been powered down you will need to open up the system. Please see below to locate the screws that need to be removed.

NVRCUBE or NVRWIFI

There will be 4 Phillips head screws located on the bottom of the system. Once the screws are removed the top cover will lift off.

Lite Series DVR

There are 2 Phillips head screws located in the rear and 2 on the side of the DVR, 1 on each side. Once the screws are removed the top cover will lift off.

Pro Series DVR/NVR

There will be 4 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Extreme Series DVR/NVR

There will be 2 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Once the top cover has been removed it will expose the Hard Drive and its connections.

First we want to Unplug the Large Black Connector. Press down on the metal tab and pull the connector out of the Hard Drive.

Now we want to unplug the second smaller connector (Blue Cable) from both ends. Press down on the tab and remove from the Hard Drive as well as the System Board.

Once the connections have been disconnected. Plug them back in securely and listen for the metal tab to click. This will ensure a good connection in between the System Board and Hard Drive.

Note*

While you still have the system open, it might be a good idea to check the cooling fans for any dust or debris that could be stopping the fan from moving. This could cause the DVR or NVR to overheat.

Once the connections are tight, lets put the top cover back on. When the cover is back on you can proceed to power on the system. Once the system is powered on you will need to monitor the system and check if it is still rebooting.

Disconnecting The Internet

If the system is still rebooting you may want to disconnect it from your Router or Modem by unplugging the Ethernet cable in the rear. You will loose your remote viewing capabilities temporarily while unplugged but can help us diagnose the issue.

With the cable unplugged you may want to monitor the system closely to see if this has made any changes to the rebooting issue.

Disconnecting Cameras and Other Sources

Disconnecting cameras, alarms, extra monitors and microphones is the last thing we can try to solve your rebooting issues.

Cameras, monitors, and microphones mounted near high voltage could be causing your system to reboot by itself. If your system detects any incoming voltage or amperage coming into the rear inputs the system will shut down to protect itself from damage.

Leave your main Display Monitor and Power Source connected. Disconnect one input at a time to see if it makes a change in your reboot cycle. If you notice a change in the rebooting you can single it out by using this method of elimination.

New GUI – Start Up Wizard (Device Initialization)

DAHUA XVR 4.0 Setup Description

This article will go over the Initialization process of the units with the New GUI.

Prerequisites

Video Instructions

Step by Step Instructions

1. When you first turn on the recorder you will be greeted with the region settings. Click on the drop down menu and select “United States” and click Next.

2. Select the proper time zone setting for your region.

3. You will now be prompted to input a password for the admin account.

4. For easier login you can create a pattern, you will need to enter it twice to confirm.

5. Enter your email in order to reset the admin password in case the password was forgotten, you may also setup security questions.

Note: This is the only method to reset the password for XVRs and NVRs. If you skip this step and forget your device’s password, you will need to replace the unit

6. The Auto-check for firmware is not yet implemented in the U.S. so you can just click on next.

7. Make sure the video standard format is set to NTSC and click on “Next”.

8. Here you can go in depth with the time settings. You may want to set up the DST (Daylight savings) so that it takes affect when the time comes.

9. The recorder will be set as a static default IP address you see on the screen. Input an open local IP address and gateway from you network. If you don’t know this information you can select DHCP (highlighted in the red box) in order to automatically receive an IP address from the router.

10. If you have the recorder properly connected to the router the P2P status will indicate “Online” and you can now remote in to the unit with our mobile app/PC app.

11. You can select the Encode settings for each camera by selecting the drop down menu on “Channel”.

12. Select the resolution and image quality for snapshots.

13. Select what you want to to when the hard drive fills up.

14. Here is you recording schedule, the green will indicate 24/7 recording and Yellow will be Motion recording.

15. Here is you Snapshot schedule, same color legend as recording,

16. Once all that is setup you will be greeted with the final Prompt! You are now finished Initializing you new recorder

New GUI- Add a Dahua Device

Description

This article will show you three different methods to add a dahua device to our New GUI recorders. We will be adding a dahua camera with all three methods.

Prerequisites

Video Instructions

Step by Step Instructions

Method 1:

This first method is extremely simple if all the cameras are still set to default credentials and settings. We will do a device search on the network and add them with a click of a button

Method Two:

The second method is used if there’s an existing camera and it’s password was changed. You will use device search to locate the camera and then go to manual add to change the password it’s being added with

Method Three:

This last method is used when Device Search fails and cannot locate the camera on the network. You will need to type in the camera’s information manually.

New GUI – Account Setup

Description

This article will go over how to add a user on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Log into the web interface of the device

.

2. Click the Menu icon in the top left of the page

.

3. Select Account

.

4. Click Add User

5. The Add User menu will appear. Use this window to ill out full user details

6. In the Authority menu you can define the individual rights of the User using the System, Playback, and Monitor tabs as well as which channels the user can access

Select which features you wish the user to have then click Save

7. A message will confirm when the user is successfully added

New GUI – Schedule Record Setup

Description

Dahua NVRs and DVRs offer a variety of recording options. You can configure recording schedules based on the following methods:

These schedules can be set individually for each camera or copied to all cameras.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Management”.

2. Select the “Storage” option from the drop-down menu.

3. From the left hand side, select “Schedule”.

4. Select the channel drop-down menu to choose the channel that you want to adjust the recording schedule for.

5. Select “Setting” next to any day of the week.

6. You will have options to set a schedule for General Recording, MD (Motion Detection), Alarm, MD & Alarm, Intel, and POS (Point of Sale). For this tutorial we are using General Recording.

7. Here you can see that you are able to set multiple periods. For this tutorial we will only be setting one period. Check the “General” box, then select the day or days you want to scheduled recordings for, and then select “Save”.

8. Depending on the days selected from the previous step, you will see green colored bars which represents general recording.

9. You can select “Copy” to mirror the same schedule to another channel/camera. Select “Save” in the Copy menu.

10. Select “Save” at the bottom to save all settings. If your changes were successfully saved, a pop-up will appear at the top notifying you as such.

New GUI – Motion Detection Recording Setup

Description

This article will go over Motion Detection Recording setup in detail on the recorder’s new GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. On the main menu select Alarm

2. Select Video Detection on the left.
Then select the Motion Detection tab at the top.
Choose the channel from the drop-down next to Channel.
Check the box next to Enable.
Check the box next to Record Channel.
Click on Setting next to Region

3. Highlight the areas in red where you want to track motion.
Then click OK at the bottom

4. Select More at the bottom
Check the boxes next to any of the other options you want to activate when motion is detected.
Click on OK

5. Click on Apply at the bottom.
You will see “Operation Succeeded” at the top when your changes have been saved

6. Click on the Setting drop-down at the top and select Storage

7. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel from the drop-down next to Channel.
Click on the Setting button next to any day of the week.

8. Check the All box to enable all days of the week.
Check the Motion box for “Period 1”.
Click OK at the bottom.

9. Click on Apply at the bottom to save the settings

10. Select Record Mode on the left.
Then make sure Auto is enabled for the appropriate channel(s).
Click on Apply at the bottom.

11. Click on the Main Menu icon at the top right.
Then select Search

12. Check box next to the channel on the right.
You should see yellow lines/bars for motion recording

Alarm Record Setup

Description

This article is to show you how to setup alarm recording thru new Web GUI.

Note: please refer to product spec sheet for alarm input/output availability. Not all Dahua Recorder support alarm input/output.

Prerequisites

Video Instructions

Step by Step Instructions

Setup Alarm Input

From main menu, click on Alarm. Click on Alarm input. We are using XVR 72 series for this example. The Alarm Input page will launch as shown below:

Select the Alarm input number that you like to use. This number is correspond to the alarm port on the back of recorder.

1. Click Enable to enable the alarm input.

2. Enter Alarm Name. By default is set to AlarmIn#

3. Period is to schedule your Alarm when you want to be enable.

4. With the alarm input, you can trigger recorder’s alarm output.

5. This to select which channel you want recorder to start recording when alarm is triggered.

6. You can call basic PTZ action Preset, Tour, or Pattern when alarm is triggered.

.

Setup Alarm Recording Schedule

1. From the main menu, click on Management > Storage > Schedule.

2. Select the channel you like to setup.

3. To enable Alarm recording, Click on Setting next to the timeline bar.

4. Set your duration (By default is 24 hour, 00-24). Then select Alarm.

You can select all days to copy the schedule to all week. Click Save.

5. Click Save.

New GUI/Instructions/IVS Record

Description

This article will cover how to configure IVS Recording on a Dahua recorder with the New GUI

Prerequisites

Video Instructions

Step By Step Instructions

1. From the Main Menu select AI

2. Select Parameters on the left.
Then select Smart Plan below it.
Choose the channel of the camera you are configuring from the Channel drop-down.
Select the IVS “Lightbulb” icon so that it highlights blue.
Then click Apply at the bottom

3. Select IVS on the left.
Choose the channel of the camera from the Channel drop-down.
Then click the + button.
Double-click on the rule type under the Type column to choose the type of IVS rule you want to use.
Adjust all the settings in the Parameters section.
Make sure that the box is checked next to Record Channel and the channel that camera is on is highlighted next to it

4. Draw the rule in the live view on the left by left clicking on it.
Continue to left click to add more segments.
When you are done, right click to finish drawing the rule.
Then click Apply at the bottom

5. Select Setting at the top left.
Then select Storage from the drop-down

6. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel of the camera from the Channel drop-down.
Then click on Setting to the right of any day of the week

7. Check the box next to All to select all days of the week.
Check the box for Intelligent to the right of Period 1.
(Feel free to adjust the days of the week and the time period for when you want to record IVS events).
Then click on OK

8. You will see blue bars on the schedule representing when IVS events will be recorded, when they are triggered.
Click Apply at the bottom

9. Click on the Menu icon at the top right to go back to the Main Menu.
Then click on Search

10. Check the box next to the camera channel on the right.
Once IVS events have occured they will appear as blue bars on the timeline at the bottom.
Click on the timeline on one of the blue bars to start playing that IVS event

New GUI – Audio Record Setup

Description

This article will go over setup for audio recording on our New GUI devices

Prerequisites

OR

Note: Please reference the specification sheet for the device to confirm which audio features it supports, this can vary between models of recorder

Video Instructions

Step by Step Instructions

Enable audio source

1. 1. Login using a web browser.

2. Click on Setting > Camera.

|

3. Click on Encode. And then select the camera channel that support audio.

|

4. Click on More.

5. Click on the checkmark to enable Audio.

6. Select the Audio source for your HD-CVI camera. If your HD-CVI camera has built-in Microphone, select HDCVI as the audio source. Local option is if you are connecting external microphone to the recorder.

7. Click OK, and then click OK again on the bottom right hand corner.

Setup audio recording

1. Login using a web browser.

2. Main menu 1st screen.

3. Main menu 2nd screen.

4. Click on the Audio Option.

5. Audio File Manager Option.

New GUI – Playback

Description

This article will cover how to play back recorded video on an NVR or DVR with the New GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Video”

2. The Playback menu should open up and look like this:

3. On the right hand side, there will be a calendar. Select the day that you wish to play back video.
Below the calendar is a list of all the cameras/channels. Check the box next to all the cammeras/channels you would like to play back video from.

4. The video footage willl appear on the timeline at the bottom of the screen. It will be color coded to match the types of video that were recorded.
(See the Legend at the bottom of the screen.)

5. Check or uncheck each type of recording that you want to view. Check the Sync box if you would like to sync playback up on all channels you are viewing.

6. Double click on the graph at the bottom to begin playing back video.

=How to back up video files on new UI

Description

This article is to show you how to back up the video file from new system UI.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the main menu, go to the second menu page, and click on Backup.

2. Backup page will launch as shown below:

3. You must plug in an external drive to save your downloaded file. Select the path where you want to save the file at. From this pop-up screen, you have an option to create new folder. After you select, click OK.

4. Select the Record Channel you like to search. You can only search 1 channel at a time.

5. Select the Recording Type you like to search.

6. Set the start and end time for searching. Then click Search. All recorded files that meets your search criteria will shown on the list.

7. Select the files, and click Backup.

8. Downloading process start.

9. Once finished, the folder information will pop up, then click OK.

New GUI – P2P Setup

Description

This article will go over initializing P2P on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Under “Management” go to Network>TCP/IP

2. You can either set the device on a static ip or turn DHCP on to automatically grab an IP from the network. Save any changes

3. Locate P2P tab on the lower left and enable P2P

4. After saving it you should see the the status change to “Online”, You can now use this device for remote viewing on our software

Remote Access/Remote Access Setup Port Forwarding

Create port forwarding rule in the router

Description

Port forwarding is a function of network routers that allows a user to configure specific communication ports to be routed to devices on an IP (Internet Protocol) network, such as a computer, DVR, or IP camera.In this case for CCTV equipment, it allows the user to view and control CCTV equipment remotely. Follow the step by step instructions and the instructions your manufacturers hardware to setup port forwarding, or try PortForward.com to search for your routers settings.

Prerequisites

Video Instructions

Step by Step Instructions

1. Connect NVR to network with a CAT5 cable.

2. Download and install ConfigTool from DahuaSecurity.com, under Support->Download Center->Software

3. Run the ConfigTool.

4. The ConfigTool should display your IP Camera. Click the, “” icon to open Internet Explorer and access your NVR.

5. Configure Internet Explorer security settings to allow the plugs to work. Link to Internet Explorer Setup

6. Login with the default credentials: User Name: admin Passsword: admin

7. Under, Main Menu -> Setup -> TCP/IP Change the IP Camera to, “Static” if the camera is currently set to, “DHCP”

8. Open another tab and enter the, “Gateway” address listed under your NVR’s Network settings. Example: 192.168.1.1, 192.168.0.1, 10.0.10.1

9. Login to your gateway and locate the, “Port Forwarding” section.

10. Create port forwarding rules for each port you wish to forward for the NVR. (Usually you will only need to forward the HTTP and the TCP port.) Default Ports: TCP: 37777 UDP: 37778 HTTP: 80 RTSP: 554 HTTPS: 443

11. The end result should look like the below image. We used a Cisco router for this example.

12. Hit, “Save” in the gateway interface, and open another tab.

13. Go to, “www.canyouseeme.org” and check that the ports you opened on the gateway.

How to Access System Using P2P via Mobile Application

Description

View your recorder and cameras on the go. With Dahua’s mobile application IDMSS(IOS)/GDMSS(Android) allows you to add Dahua recorders and cameras to the mobile app using P2P.

Prerequisites

Video Instructions IDMSS/GDMSS version 4.50.000

Step by Step Instructions iDMSS/gDMSS version 4.50.000

1. Open iDMSS/gDMSS on the phone, and select the home icon located on the top left corner.

2. Select the “Device” button/icon on the bottom to add the recorder/camera.

3. Select the “+” sign then select “Scan” to add the device.

4. Select the “Wired Camera”.

5. Input the device for easy identification. It’s required to input the password for the added device then select the save icon located on the top right corner.

Step by Step Instructions IDMSS/GDMSS version 4.20.000

1. Select the Menu Icon

2. Select “Device Manager”

3. Select the Add Icon

4. Select “Camera”

5. Select “Wired Device”

6. Select “P2P”

7. Input Info and select “Start Live Preview”

Video Instructions IDMSS/GDMSS version 3.50.000

Step by Step Instructions IDMSS/GDMSS version 3.50.000

1. From the home screen of the mobile application select “Camera”.

2. Select the menu button.

3. Select Device Manager.

4. Select add button to add device.

5. Select Wired Device.

6. Select P2P.

7. Name your device -> tap the QR code to bring up QR code scanner.

8. Input the username -> password -> and select live preview. By selecting “Start live preview” device will be automatically saved into the application.

IDMSS/GDMSS Version 3.40.003

Video Instructions Version 3.40.003

Step by Step Instructions Version 3.40.003

1. Click, “Camera”

2. Select the Menu Icon

3. Select “Device Manager”

4. Select the Add Icon

5. Select “P2P”

6. Choose a name for the device → Scan in QR code for SN number which you can access from the physical recorder under the main menu → Setting → Network → P2P. You may input SN number manually which can also be found under the recorder. → Enter Username and Password. For best results , leave Live Preview and Playback on the Extra Stream.

7. Select the Disk Icon to save → Select Live Preview, At which time the app will connect to all cameras.

Setup Remote Access via P2P using SmartPSS

Description

This allows you to view cameras on SmartPSS using P2P.

Prerequisites

Video Instructions

Step by Step Instructions

1. Locate the serial number of your NVR or DVR. The serial number can be found at the following locations:

2. Launch SmartPSS and select Device.

3. Click Add, change method to P2P.

4. Enter credentials, save and then add.

.

How to Download and Prepare Firmware

Description

This guide will show how to download and prepare the firmware file for a Dahua device.

Firmware files for Dahua devices can be found at Firmware by Device or the specific product page for the device

Firmware is typical provided in a ZIP file, a compressed file format

This file will contain the actual firmware file, which needs to be extracted from the ZIP file in preparation for the upgrade

Prerequisites

• Computer with internet access (to download firmware file)

• Dahua device

Video Instructions

Step by Step Instructions

Confirm the Model and current firmware of Dahua device

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Info

3. Click Version

The Device Type will be displayed

The current System Version will be displayed

Download the firmware file for device from DahuaWiki

4. In a browser go to DahuaWiki.com

Under Specifications, Firmware, & Manuals

Click the device type (in this example Recorder)

5. Enter the device model into the field

6. The results will be filtered

7. Click the firmware icon to download the firmware file

8. The file will download

Extract the firmware file to local computer

9. Right click the Start Menu / Windows icon in the bottom left of the screen

Select File Explorer

10. Select Desktop

11. Click Home

Then click New folder to create a new folder to extract the contents of the firmware zip file

12. Find the created folder in the list, double click to open

13. Under the Downloads window of the browser, click ‘Show in folder’

A new File Explorer window should open containing the directory the firmware zip was downloaded to

Locate the file in the list

14. Right click

Select Cut

15. Select the window with the new directory

Right click in the window

Select Paste

The folder will appear in the directory

16. Right click the file

17. The contents of the zip file will appear in a new window

18. Click to select all files in the folder

Drag and drop the files to the created folder

The files will appear in the directory

The firmware file will appear in the directory ready to use

How to Reset Device to Factory Default

Latest Dahua firmwares 2024

Step by Step Instructions

1. From Live View

Right click select Main Menu

2. Under Setting

Click System

3. Click Default

4. Click Factory Reset

5. A prompt will appear to confirm the factory default

Click Yes

6. The unit will default and reboot

7. When the device has booted back up it will be factory reset and is now ready for device initialization

SystemUI New

Step by Step Instructions

1. From Live View

Right click, select Main Menu

2. Click Operation

3. Click System Maintain

4. Click Default

5. Click Factory Default

6. A prompt will appear to confirm the factory default

Click OK

7. The NVR will default and reboot itself

8. The unit will boot back up

9. The device has been factory reset and is now ready for device initialization

WebUI Old

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Setup

3. Click System

4. Click Default

5. Click Factory Reset

6. A prompt will appear to confirm the Factory Reset

The unit will reboot and is now ready for device initialization

WebUI New

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Setup

3. Click System

4. Click Default

5. Click Factory Reset

6. A prompt will appear to confirm the factory default

Click Yes

The unit will reboot and is now ready for device initialization

Firmware Update via USB Drive

Description

This page will show you how to update the firmware of your Dahua device via a USB drive at the recorder

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device

• USB drive with the firmware file for the device – Firmware by Device

SystemUI Old

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

1. Download Firmware and copy to USB such as a flash drive ➞ Insert USB into recorders USB port.

2. It will prompt for option to upgrade, Click System upgrade ➞ Click Start.

3. Browse for firmware ➞ Open firmware folder is in ➞ Select Bin File ➞ Click Start. Device will reboot once finished.

SystemUI New

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

USB drive with Firmware file should be plugged into USB slot on recorder

1. From the Main Menu, click Operation

2. Click System Maintain > Upgrade

3. Click the System Upgrade in the middle of the page.

4. Select the Firmware file from the list

Click OK

5. The firmware update will begin.

Make sure to not unplug the power during this process.

6. The NVR will reboot as the final step of the process

Firmware Update via WebUI

Description

This page will show you how to update the firmware of your Dahua device via the WebUI

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device with network connection

• Local Windows computer

• Firmware file for device downloaded to computer – Firmware by Device

Instructions

WebUI Old

Prerequisites

• Computer

• Internet

• Compatible Browser (Internet Explorer)

• NVR/HCVR/IPC

Video Instructions

Step by Step Instructions

Step 1: From IE(Internet Explorer) type in the devices IP address on the IE address bar → login with credentials.

Step2: Setup → System → Upgrade

Step 3: Click on “Browse” → Select correct firmware

• Click on “Upgrade”

• Device will reboot after upgrade is finished.

USB firmware Upgrade via web.

If firmware is on USB Device → Click on browse → Navigate to USB location → Select firmware → Open → Upgrade.

WebUI New

Prerequisites

• Dahua device with network connection

• Local windows computer

• Firmware file for device downloaded to computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Operation

3. Click System Maintain

4. Click Upgrade

5. Click Browser

6. Locate the firmware file

Click Open

7. Click Upgrade to begin the update process

8. A message will appear to confirm the upgrade process

9. When the upgrade is complete the device will reboot

Firmware Update via SmartPSS

Description

This page will show you how to update the firmware of your Dahua device via SmartPSS

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• SmartPSS installed

• Device added to SmartPSS

• Firmware file downloaded to computer – Firmware by Device

Instructions

SmartPSS 2.002

Prerequisites

• SmartPSS installed

• Dahua device added to SmartPSS

• Firmware file for device downloaded to computer – Firmware by Device

Video Instructions

Step by Step Instructions

1. From the Main Page of SmartPSS

Click Device CFG

2. Click to select the device from the device tree on the left side of the screen

3. Click Upgrade

4. Click the folder icon

5. Locate the firmware file

Click Open

6. Click Firmware Upgrade to begin the firmware update process

7. A prompt will appear to confirm the upgrade process

8. A prompt will appear to confirm a successful upgrade

Firmware Upgrade via ConfigTool

Description

This page will show you how to upgrade the firmware of your Dahua device via ConfigTool

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device(s) with network connection(s)

• ConfigTool installed on a local computer

• Firmware file for device(s) downloaded to computer – Firmware by Device

Step by Step Instructions

Single Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the device you are looking for in Start IP and End IP.
Enter the login information for that device in Username and Password.
Then click OK at the bottom

3. Click on Device Upgrade on the left.
Find the device you want to upgrade in the list and click on the Folder icon next to it under the Upgrade File Path column

4. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

5. Verify the file path is listed next to the device in the list.
Then click on the Upgrade icon to the right of the device in the Operate column

6. Click on OK

7. The progress bar will fill up as the device is upgraded

8. Once the device has been successfully upgraded you will see a Green Check Mark next to it in the list

Batch Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the devices you are looking for in Start IP and End IP.
Enter the login information for those devices in Username and Password.
Then click OK at the bottom

3. Click on Device Upgrade on the left.
Find the devices you want to upgrade in the list and check the boxes next to them. (Make sure all devices you check require the same firmware.)
Then click on Batch Upgrade at the top

4. Click on OK

5. Click on Browse

6. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

7. Click OK at the bottom

8. The progress bars will fill up as the devices are upgraded

9. Once the devices have been successfully upgraded you will see Green Check Marks next to them in the list

Recorder Firmware Update via Online

Description

This page will show you how to update your Dahua Recorder online.

Note: All devices should be “Factory Reset” once the firmware update is complete.

When the NVR detects there is a newer firmware in the server, a ‘1′ icon will appear at the System icon.

The entire process takes about 5 minutes depending on network connection.

Prerequisites

• Dahua device that supports online update

• Internet connection to Dahua device

Instructions

SystemUI

Prerequisites

• Dahua device with internet connection

Video Instructions

Step by Step Instructions

1. From Live View

Right click, select Main Menu

2. Click Operation

3. Click System Maintain

4. The upgrade menu will show if a new firmware version is available

5. Click Upgrade Now to begin the update process

6. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

7. The firmware file will begin to download

8. After the download is complete the unit will automatically begin the firmware upgrade

9. The unit will reboot as the final step of the upgrade

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

From Live View, right click Select Main Menu

11. Click Operation

12. Click System Maintain

13. Click Default

14. Click Factory Default

15. A prompt will appear to confirm the factory default

Click OK

16. The unit will reboot

17. When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

WebUI

Prerequisites

• Dahua device with internet connection

• Local Windows computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Operation

3. Click System Maintain

4. Click Upgrade

5. The upgrade menu will show if a new firmware version is available

6. Click Upgrade Now

7. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

8. The firmware file will begin to download

9. After the download is complete the unit will automatically begin the firmware upgrade

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

12. Click Operation

13. Click System Maintain

14. Click Default

Click Factory Default

15. A prompt will appear to confirm the factory default

Click OK

The unit will factory default and reboot

When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

Index of /Firmware

.

.

How To Setup a Security Camera System?

The first phase in setup of a security camera system consists of installing the cameras and running the wire. The second phase is completing the connections between the cameras and the recorder, which depends on the type of camera system you have purchased.

How To Setup a DVR Camera System

DVR camera systems consist of security cameras that have BNC jacks to send video over coax wire, and a 12VDC power connector for power. Such coax wire based systems use RG59U siamese cables that have BNC and 12VDC power connectors at each end, which allow video and power to be run together over one “siamese cable.” As shown in the setup video below, BNC connectors are silver colored metal connectors that twist lock on to the video jacks of a camera and DVR recorder.

Infrequently, an installer may use network cabling with video baluns instead of coax cabling, which was very common with older CCTV systems to transmit video signal over long distances. Regardless of whether you are using coax wire or video baluns, setup of a DVR camera system is similar as demonstrated in the following video:

How To Setup a NVR Camera System

NVR camera systems use plug-and-play IP Cameras that connect directly to built-in PoE ports on the back of the NVR. Such systems are also commonly referred to as PoE IP camera systems because the cameras use Power over Ethernet technology to send power/video/data all over one network cable. We recommend using CAT5e cable as a minimum, and CAT6 wire is recommended for runs longer than 150ft as its thicker wire gauge allows for improved power transmission.

Our IP camera systems feature plug-and-play compatibility between the NVR and IP camera. Unless otherwise specified, we ensure the cameras and NVR we sell are compatible with each other and allow even a novice user to setup a IP security camera system.

To gain a good understanding of your purchase, we recommend customers bench test IP cameras with the NVR recorder before installing the cameras. Once it is established that all cameras are operational, continue with mounting the cameras at the desired location and running the camera wire. Since installation errors are common when crimping CAT5e or CAT6 network cable, we recommend using a cable continuity tester to safeguard against wiring related issues.

As each camera is installed and connected to its wire, follow the video below to learn how to connect each IP camera to the NVR in a NVR camera system.

Once cameras are installed and wired to the digital video recorder it is time to login, and start using the system, which leads us to the third phase

How to use your surveillance system

1. How To Login to a Security Camera System

Before you are able to login to your camera system over the web, you need to login at the DVR or NVR itself using a mouse. Connect the recorder to a monitor that supports at least 1080P resolution. We recommend using a HDMI input capable monitor. Turn on the recorder and login using two possible login methods.

Please watch the video below to learn more from our video tutorial about the two different ways to login to your or security system.

In case you are unable to login due to a forgotten password, it is easy and secure to reset the password and gain entry into the unit. It is required that you be present at the recorder when following the video guide below on how to reset the login password. As shown in the video below, by answering some simple security questions you can quickly reset the login password.

2. Viewing Live Video and Audio on a Security System

All of our DVR Systems and HD NVR systems allow multiple viewing options. You can view multiple cameras in a grid-view or view one camera at a time in full screen mode. Full screen mode also allows the user to listen to audio from security cameras with built-in microphone. To hear audio from cameras, all of the following conditions must be met:

For a comprehensive guide of the different viewing options offered by our security camera systems, please watch the following video:

Regardless of whether you have an IP security camera system or DVR camera system, both provide the user with two types of zoom:

It is important to understand the difference between digital zoom and optical zoom, and the fact that optical zoom can only be used in live view mode. Below is a detailed video demonstration of each type of zoom function and how both can be utilized during live view to see objects far away. Using a 4MP security camera mounted 7ft above the object of interest, we show the power of optical zoom provided by a motorized zoom security camera to view objects in fine detail.

If your system has motorized zoom cameras or a outdoor PTZ camera that you purchased from CCTV Camera World, they can be easily controlled using our surveillance video recorders. Regardless of whether the motorized cameras are HDCVI or IP cameras, or whether your recorder is a DVR, XVR, or NVR, the cameras can be controlled using the friendly GUI interface of our systems as shown in the following video.

3. Setting Recording Resolution

A common misconception about our camera systems is that all cameras have to be the same resolution, which is not the case. Cameras of different resolutions can be used on the same recorder in any of our systems, granted the cameras are within the maximum resolution limit of the recorder. This is true for systems consisting of Tribrid DVR, XVR, or NVR recorders.
Encoding settings can be set individually for each camera channel. Depending on the maximum recording resolution supported by the recorder and the camera, our surveillance recorders allow up to 12MP recordings. All of our DVR and NVR recorders also have dual video encoding technology to provide two streams of video for each camera channel:

The Encoding menu has several settings that can be set. A good understanding of the following settings is important in getting the most out of our security camera system purchase from CCTV Camera World.

The in-depth video tutorial below discusses encoding settings available in your system and how to configure them.

4. Customizing Video Settings

We manufacture our cameras to produce the best possible picture quality automatically. Sometimes peculiar lighting scenarios in a scene may require customization. Our DVRs and NVRs allow multiple picture quality settings to be modified from the recorder as explained in the detailed video tutorial below. It is important to note that there is a difference in capabilities to modify image settings when comparing coax based cameras versus IP cameras.

Coax based cameras produce video that is encoded by the DVR, thus allowing picture quality to be modified before the video is saved by the DVR. In contrast, IP cameras encode video that is streamed to the NVR for saving the video stream; the video is not encoded by the NVR. Therefore, any changes made in the picture settings on the NVR must be communicated back to the IP security camera. If an incompatible IP camera is used with an NVR, such changes will not be communicated to the IP camera, and changes will not apply before video is encoded by the camera.

Our systems allow a wide variety of picture settings to be toggled depending on the camera specifications. In addition to picture brightness and contrast, the user can toggle image quality features such as backlighting, glare compensation (WDR), and image flip.

https://youtu.be/zW3g-dTV30w

5. Recording Method Configuration

All of our security systems offer a variety of video recording methods. Each security camera can be set to record independently and the user has the option to choose from the following recording methods:

The digital video recorders in our systems even allow multiple recording methods for each camera. For example, cameras can be set to record all the time or during a portion of the day using the scheduled recording method, while also recording upon motion detection. This preserves video integrity in case a motion event is missed, and is very helpful when reviewing recorded security footage to allow the user to skip to points in the timeline when motion is detected. The video tutorial below is an in-depth guide on how to set the different recording methods for each camera in your surveillance system.

https://youtu.be/jRfV3N8sAqY

6. Playback Recorded Video on your Surveillance System

CCTV Camera World’s security camera systems have a user-intuitive graphical interface to playback recorded video. Using a mouse connected to your recorder, it is easy to review recorded security footage in the Search menu. It takes 3 simple clicks to playback recorded video:

The video above is a comprehensive tutorial on how to playback recorded video, in which we cover:

You can playback one camera or multiple cameras depending on the resolution of the recording and the playback capability of the recorder that is part of your system. Our 4000 series NVRs support playback of up to eight 1080P channels, while our 5000 series NVR support up to sixteen channel playback at 1080P. Stronger playback capability is available when playing video over the network using our free computer client software to playback video on a PC or Mac workstation.

7. How to Download Video from a Security Camera System

When there is an incident, it’s important to have a camera system that allows easy download of security footage catching the perpetrator in the act. Our security camera systems are based on this simple principle to allow easy video download of a short video segment to a USB drive and playback on a Windows or Mac computer. To download video from any of our standalone recorders you will need a USB flash drive that is formatted with the NTFS or FAT  file system. The flash drive should not be more than 256GB. The video guide below on how to download footage from your security camera system walks you through the process.

Briefly, below is a list of simple steps on how to download video from a DVR Camera System or HD IP Camera System purchased from CCTV Camera World.

8. How To View Downloaded Footage from a Security Camera System

Once security footage has been downloaded from your surveillance system, it can be reviewed on a Windows or Mac OS computer using our free playback software called Smart Player. You can download it here for Windows and Mac. Here is a list of features of Smart Player which makes our systems one of the best security camera systems in the industry for video archiving and review:

.

Safety cautions

Product overview

DVR

Camera

Power Cable Splitter

BNC Cable

Xmeye Dvr System Instructıons For Use

Read Also : Camius devices troubleshooting

Hard Drive Installation

IMPORTANTTo record videos and play the historical videos, the installation of the Hard Disk Drive is a must.
Otherwise,you can only watch the live video.
This DVR system works with a 3.5” SATA Hard Drive.The Hard Drive should be formatted after it’s installed.×Dismiss this alert.

System Connections

IMPORTANTDo not fix the AHD camera before you can view the image on the monitor and confirm the ideal position to install it.×Dismiss this alert.

1.Plug a power adapter into the DVR and the socket to power on the DVR.

2. Connect a monitor to the HD Output or VGA Output on the DVR with an HDMI cable or VGA cable (not included).

3. Connect the Ethernet Cable with the DVR and your router.

4. Connect the AHD camera with the BNC Cable.

5. Connect the Yellow Video Connector to the BNC Video Input on the DVR, and connect the Red Power Connector to the Male Connector of the Power Cable Splitter.

6. Connect the Female Connector of the Power Cable Splitter with another power adapter. Then plug the power adapter into the socket to power on the camera.

Operate dvr system with a monitor

Startup Wizard

After connecting the DVR and cameras to power, wait for 2-3 minutes. A Startup Wizard will start to guide you via a series of pop-up windows.

Connect the USB mouse to the DVR, then click Next until you see the window of Time-Language Configuration.

1.Select the time zone, date format, time format, language, and set the time for your DVR system.

2. The default password is empty, please reset it for your DVR following the tip.
The new password should be more than 6 digits and use the combination of numbers and letters to ensure your system’s security.

3. Select safety questions and enter the answers for resetting the password if necessary.
You can also enter your email address for getting the verification code to reset the password.

4. Check if the network connection status is normal. If not, you can configure it by clicking Network.

5. Scan the QR code to get the Serial Number of your DVR system and download the App named XMEye into your mobile device.

6. Before fixing the cameras, you can log in to XMEye App to check the live view to confirm the ideal position.

7. Detection based on human shape is enabled by default.
The DVR system will send alerts to your mobile device when there is human shape detected by the cameras.
Please refer to the section of Motion Detect the detailed setting.

IMPORTANTClick Next and OK to exit the wizard. You can right click on the screen, then go to Main Menu > Startup Wizard to bring it up again.
If the wizard is no longer needed, just check the box before Don’t Display the Wizard again on the first interface of the Startup Wizard.×Dismiss this alert.

Live Video

You will see the live videos from the AHD cameras in split-screen mode (9 screens by default) after exiting the wizard.

※ Move the mouse cursor to the live video of any channel, some icons may be displayed according to the setting.

Notes:

1.The icons of and are displayed by default, while for icon , and , please right click andgo to Main Menu > Alarm (see on page 15) to enable them.

2. If you want to loop to display the live videos from some certain channels in full-screen mode, please go to Main Menu > System > Tour to enable this function.

3. For viewing the live video from one channel in full-screen mode, please move the mouse cursor to the desired channel, then double click. To exit full-screen mode, double click again.

Hard Drive Formatting

When you receive the system, the system has a pre installed hard disk, which does not need to be formatted,but if you have to replace another hard disk, it needs to be formatted at first ,then it can be used normally Install the Hard Drive first, then right click and go to Main Menu >Advanced > Storage to check if the type is Read/Write or the status is Normal.

If not, please click Format Storage to start formatting your Hard Disk Drive.

Video Recording

Right click on the screen, then go to Main Menu > Record > Record Conf. to set the record mode and record plan.
This DVR is set to record videos 24 hours a day by default.

Channel:

Select the channel to set the record mode and plan. You can select a single channel or all channels.

Redundancy:

Installing 2 pieces of Hard Disk Drive is required when enabling this function, and HM245 doesn’t support it.

Length:

Set the maximum video length of each recording from 1 minute to 120 minutes. It’s 60 minutes by default.

PreRec:

The camera will start recording a video around 5s before it detects the motion or human shape.

You can reset the time from 1s to 30s, but the accuracy of the pre-recording time may be affected by the bitrate.

Mode:

Set the recording mode and the options are Schedule, Manual and Stop.

Record Plan:

Set the recording schedules.

Notes:

The oldest video will be overwritten by the latest one by default when the Hard Disk Drive runs out

of space.

Video Playback

Right click on the screen, then go to Main Menu > Record > Playback to play the video recorded.

You will see the different playback modes in the pop-up window of Play Mode.

Explanation of playback modes

1.Common Playback

Select the channel(up to 4 channels at the same time), a period and a date on Blue background to

play all types of videos recorded.

1. Area for Video Playing
2. Playback Buttons
3. Timeline
4. Channel
5. Filters
6. Filtered Videos List
7. R: Standard Videos
8. M: Videos recorded when the camera detects motion or human shape.
9. Detailed Info. of the Selected Video
10. Search
11. Show/Hide Filtered Videos List
12.Timeline by Hour/Minute

TipFilters will not be available after you left click on the timeline, but you can exit this mode and re-enter to select the filter.×Dismiss this alert.

Option 1 :

Left click on the Green/Red (Green for standard videos recorded, and Red for the videos recorded whenthe camera detected motion or human shape) part of the timeline of each channel to play the historical videos.

Option 2 :

Left click on the live video of one channel, show the filtered video list, then double click on the selected video to play it.

Description of Playback Buttons

Left click on the live video of any channel, then start using the buttons to control the video playback.

Tips:

① You can click the icon to cut a video, then click to back up to the external storage.

② Previous Frame and Next Frame work only when pausing the video.

③ The speed of Fast Reverse and Fast Forward will be displayed on the right end of Playback Buttons.

2. Sync Playback

This function aims to put the videos from different channels at the same time to compare.

Select 2 channels at least ( up to 4 channels), a period and a date on Blue background to play the historical videos simultaneously at the selected time on the same timeline.

3. Dayparting

This function aims to put the videos from the same channel but at different time to compare.

Select a channel, number of split screens, and a period to play the videos recorded from this channel on different timelines.

NotesYou need to press and hold the left mouse and move on the bar of Period to select time period.×Dismiss this alert.

4. Smart Express

Select one channel or all channels, then select the speed of Fast Playback, the system will play all the videos recorded with the speed you selected.

5. Smart Search

Select one channel and a time period, then check the box before Detect and select a date on Blue background to play the videos recorded when the camera detected the motion or human shape.

※Double click the thumbnail to play the related videos.

6. Face Search

Select one channel, a time period and a date on Blue background to play the videos recorded when the camera detected faces.

Video Backup

Step 1:

Insert the USB disk into the USB port of the DVR system. Right click on the screen, then go to Main Menu >Record > Backup to start.

Step 2:

Select your USB disk, then click Backup to bring up a pop-up window.

Step 3:

Select Channel, Start Time and End Time, then click Add to display all the filtered videos.

Step 4:

Check the box to select the video files and Backup format, then click Start to back up the videos.

Tips:

① The format of the USB Drive should be FAT 32.

② An alternative solution to back up the videos is listed below.

• Go to the interface of video playback and click to show the filtered video list.

• Check the box to select the videos.

• Click to start backing up. The next steps are the same as the first solution mentioned above.

Snapshot Setup

The system will capture the snapshots 24 hours a day when the camera detects motion or human shape.

Go to Main Menu > system> SnapShot Conf. to reset the time interval of capturing a snapshot, and set up the schedules when the camera will capture a snapshot as well.

Alarm

IMPORTANT:

The alarms of Motion Detect and Human Detect are enabled by default. If you need to record videos whenthe camera detects the face or gets blocked as well, please enable Face Detection and Video Blind.

Please go to Main Menu > Alarm to set the alarm you need.

Motion Detect

The camera will start to record videos when it detects motion.

Channel:

Select the channel you’d like to enable motion detection.

Enable:

Check the box to enable motion detection.

Sensitivity:

If you select higher sensitivity, the camera will be more easily to be triggered to start recording videos. It’s advised to select Middle to balance the accuracy and effectiveness of the alarm, thus reducing the false alarms.

Region:

Click Set, then press and hold the left mouse to drag and select the area for detecting. The pink area indicates the selected area.

Period:

Set up to 4 time periods for each day to send the alerts when the camera detects motion.

MD Interval:

Set the time interval of two alerts. It aims to decrease the frequency of the alerts caused by the same moving object.

Record Channel:

The selected channel(s) will start recording when the current channel detects motion.

Tour:

The display will loop to display the live video from the selected channel(s) in full-screen mode when the current channel detects motion. You can go to Main Menu > System > Tour to set the time interval to show the live video in full-screen mode.

Snapshot:

The selected channel(s) will capture a picture when the current channel detects motion.

PTZ Activation:

The cameras don’t support this function.

PostRec:

The camera will remain to record the video around 10s after the motion or human shape detection ends. You can reset the time from 10s to 300s.

Show Message:

After enabling this function, the display will pop up a window to show the Alarm Status for all kinds of alarms when the cameras detect motion, human shape, or more.

Send Email:

Before enabling this function, please go to Main Menu > System > NetService, then double click on EMAIL option to set up your email address to receive the alerts.

Write Log:

The logs of the alerts will be written into the system once you enable this function. You can go to Main Menu > Info > Log to check the detailed log information.

FTP upload:

The system will send the videos recorded or snapshots captured to the FTP server you set when the camera detects motion. Please go to Main Menu > System > NetService, then double click on FTP option to set up your FTP server.

Mobile reported:

The system will send alerts to your mobile device when the camera detects motion. Please install the App and add the DVR to the App following the section of OPERATE DVR SYSTEM ON MOBILE DEVICE on page 18.

Up-to-Coaxial Control

Right click on the main menu and select XVI control to start setting up your camera.

※If the live video from the camera is mirrored or flipped, you can check the box before Mirroring or Overturn to fix it.

※If you set something wrong, please click Restore to get back to default settings.

.

NotesFor the setting of alarms like Video Blind, Video Loss, Human Detect and Face detection, please refer to the settings of Motion Detect. If prompting Video Loss, the DVR will not record videos, but only to send alarms.

TROUBLESHOOTING

The DVR System Boots Up Abnormally Or Reboots Automatically.

If the issue persists, please contact Support for more help.

.

How Should I Do If I Forget My Password?

• Please click Forgot Password when logging into the DVR system.

• The system will ask you the security questions you set in the Startup Wizard, please enter the right answer to reset your password.

• If you forget the answers, click Forget Answers to enter the interface of Verification Code.

• Launch XMEye App,tap > FIND PWD on an Android device or tap Forgot your device password?(on the interface of Add Device) > FIND PWD on an iOS device to scan the QR code on the left side to get a verification code, then enter it into the box on the interface of Verification Code to reset your password. However, if you set an email to get the verification code in Startup Wizard, the App will send the code to that email. You need to get it from email, then enter it on the interface of Verification Code.

.

How Long Can A Hard Disk Drive Record For This DVR System?

There are 4 AHD cameras connecting to this DVR system by default. These cameras are with the resolution of 1080P and variable bitrate which depends on the surveillance scenes. If the bitrate is around 2Mb/s, the corresponding size of the video file will be around 21G per day.

As a result, a Hard Disk Drive with the capacity of 1T may record around 12 days.

.

How Can I Connect An Extra Camera With The DVR System In Addition To The 4 Cameras In The Package?

DVR system supports up to 8 cameras to be connected. Please contact Hiseeu to get the same type of cameras and the corresponding cables.

If you just have a camera in hand, please follow the steps below:

For the camera with the format of TVI/CVI/SVI/CVBS, right click on the screen, select XVI&AHD to set the Signal of the channel to Auto or the corresponding format of your camera, then connect the camera with the DVR system.

For an IP camera, please go to Main Menu > System > Digital > ChannelType to check the box of the fourth line, then go back to the main screen and move the cursor to the channel you’d like

to connect the camera.

Click in the center of the screen to start adding the camera.

.

The Image From The Camera Is Upside Down.

Right click on the main screen and click XVI Control, then check the box before Mirroring or Overturn to flip the image.

.

What Should I Do If It Runs Out Of The Space On Your Hard Disk Drive?

The DVR system is set to loop recording by default, which means the latest videos will overwrite the old videos automatically when it runs out of the space on the Hard Disk Drive.
You can back up the important videos, then delete the videos or format the Hard Disk Drive.

.

Why Does The Hard Disk Drive Stop Saving Videos?

.

The App On My Mobile Device Cannot Receive Snapshots When The Camera Detects Motion, Human Or The Camera Gets Blocked, Etc.?

The App can receive the snapshots by default and you can check from Alarm Push/Alarm of the App.

.

Why Does The App Remind Me Of “Maximum Video Link”?

For remote viewing, such as from App or PC Client, you can only simultaneously access the live videos from 6 channels at most. Please close the unnecessary channel.

.

Why Doesn’t The PC Client Watch The Live Videos?

.

Why Doesn’t The PC Client Watch The Live Videos?

.

What Should I Do If I Got Too Many Push Notifications From App?

This DVR system can support to send you alerts when the camera detects motion, human, face, video feed loss,or the camera gets blocked. You can go to Main Menu > Alarm to disable certain kinds of alarms to reduce alerts.What’s more, you can lower the Sensitivity, set the Region and Period to reduce alerts.

.

How Can I Modify The Time Stamp And Channel Name Displayed On The Screen When Playing The Videos Recorded?

You can go to Main Menu > System > Display to select the channel you’d like to set, then enable Time Display and Channel Title, then click Set. You can even drag them to your desired position on the screen.

.

Is the fan noise on my DVR NVR recorder normal?

Q- Is the fan noise on my recorder normal?

A- Digital or network Vide Recorder’s fan is comparable to one in a mini PC, and the sound coming out of the vent that you may hear is a sign of a DVR that’s working well.

The working fan indicates that the trapped heat is being dissipated, and the DVR can record 24/7 on the hard drive, and without this cooling mechanism, the DVR and hard drive’s life span will be shortened.

How to add IP Camera to Camius DVR (Advanced Security XVR)

Camius Trivault DVR recorders are designed to support analog security cameras via coaxial wiring and IP cameras over the Network. To add an IP camera to Camius DVR, you’d need to add PoE cameras to your local Network. Then, connect a regular network or PoE switch to the LAN port of the Camius DVR. Based on the example of a Camius 16-channel DVR, the connecting diagram illustrates this process. This system allows users to quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection.

If you are not using a PoE (power-over-ethernet) switch or a PoE injector, you can power the IP camera by connecting a UL-listed 12VDC-2AMP power supply to the DC plug on the camera and an ethernet cable between the IP camera and the router or switch on your local network.

Camius TRIVAULT4K2168R Connection Diagram

Camius TRIVAULT4K184R, TRIVAULT4K184R2 Connection Diagram

Navigate to the DVR’s Menu >> System >> General >> Mode >> Set to XVR and Apply.

Wait 1 to 2 minutes for the surveillance DVR to reboot in a hybrid XVR mode. This switch will reset the Configuration and Password.

There are a few ways to add IP cameras to the DVR, and we will describe them below.

Adding IP Cameras in the Start Wizard

While in the Start Wizard, navigate to the Network>> Date/Time >> IP Cameras.

Click the Search button to add compatible IP cameras on your local Network. Next, select the IP camera(s) you want to add, and then click the arrow icon to add them to the DVR, followed by the Next button.

Select the suitable Protocol from the dropdown (Private is for Camius IP cameras), enter the IP camera(s) credentials (User Name and Password), and click Add. Green status indicates a successful connection; grey status could show a password or network error.

Adding an IP camera while in the DVR’s Setup Menu

If you add IP cameras to DVR’s menu, navigate to Channel >> IP Channels.

Select the IP camera you wish to add, click the ‘Add‘ tab or use a plus button.

The ‘Add IP camera‘ window will pop up with IP camera details.

How to add IP Camera to Camius DVR (Advanced Security XVR) 21

Once the IP camera is added to the DVR, it will appear under the IP channel list. The green state means the camera has been added successfully. A grey color state means the IP camera needs attention, and when you click on the state icon, it will indicate if the error is caused by a wrong IP camera username/password or if it has a network issue.

To avoid network issues, make sure that your camera, DVR, and router are on the same IP address segment, e.g.

How to add IP Camera to Camius DVR (Advanced Security XVR) 22

Using the Camius XVR system, users can quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection. In addition, Camius Hybrid 8-Channel DVR recorders support up to 12 and 16-channel DVRs and up to 24 HD cameras, making a scalable solution for residential and commercial surveillance needs.

It is important to note that the cameras’ quality will significantly impact the system’s overall performance and effectiveness. Of course, high-quality cameras will provide better images, enabling more effective monitoring and surveillance, but also, Camius IP cameras offer intelligent motion, sound, and AI detection. Other manufacturers’ IP cameras are usually limited to basic video motion detection.

How to install a hard drive in a Camius DVR or NVR?

Installing a hard drive in a DVR (digital video recorder) or an NVR (network video recorder) (DVR NVR for short) is a relatively straightforward process. Still, it is essential to follow the steps carefully to ensure proper installation and prevent damage to the equipment. Here is a step-by-step guide on how to install a hard drive in your surveillance DVR or NVR recorder.

Camius network and hybrid digital video recorders accept 3.5″ and 2.5″ SSD internal hard drive disks. While 8 channel DVR and NVR recorders accept a single hard drive up to 10 TB in capacity, 16-channel DVR and NVR recording, along with 32-channel NVR will support a 14TB hard drive on each SATA port. 

Visit this link to see the tested and recommended hard drives, CLICK HERE

1 – Gather Tools and Equipment

You will need a Phillips head screwdriver, the hard drive you want to install, and any necessary screws (when you order a DVR or NVR from Camius without a pre-installed hard drive, the product box will include a set of screws for the hard drive disk installation).

2 – IMPORTANT: Make sure your DVR / NVR is unplugged and powered off

3 – Removing the Top Cover or the Video Recorder

Remove any screws from the Recorder’s top cover (chassis) using a Philips head screwdriver. Carefully remove the top chassis and set it aside (picture 1)

Picture 1 – 8 channel DVR

4 – Insert the Hard Drive

Place the hard drive into the hard drive bay, ensuring the drive is oriented correctly and appropriately seated.

5 – Connect the SATA Data and Power Cables

Connect the Data and Power cables to the two hard disk drives and place the hard disk drives on the video recorder’s case. The Data cable connects the hard drive to the DVR NVR’s motherboard. Locate the SATA port on the DVR’s motherboard and connect one end of the SATA cable to it. Then, connect the other end of the cable to the hard drive. The SATA Power cable provides power to the hard drive. Locate the SATA Power cable and connect one end to the hard drive and another to the Power Supply (pictures 2 and 3)

Picture 2 – Power and Data Cables on the Hard Drive

Picture 3 – Power and Data Cables on the DVR or NVR recorder’s board

Read Also : LaView NVR setup and user guide

6 – Secure the hard drive with srews

Carefully flip the video recorder case and secure the hard disk drives to the recorder with the four (4) screws if it is one SATA HDD (pictures 4 and 5) and eight (8) screws for the 2 SATA HDDs (picture 6)

Picture 4 – DVR with one internal SATA bay

Picture 5 – DVR with one internal SATA bay

Picture 6 – NVR with two internal SATA bays

7 – Return the DVR NVR top cover

Place the top cover on the DVR NVR and secure it with the screws (picture 7)

Picture 7 – DVR with one internal SATA bay

8 – Power on the DVR NVR

Power on the DVR NVR and allow it to boot up completely. If the hard drive was installed correctly and is in working condition, it should be recognized by the DVR and ready for use. Remember to format the hard drive (here is the guide on how to format the hard drive). Ensure that you use the power supply with the Camius video recorder.

IMPORTANT: Some users may find an issue when the hard drive is not recognized or not showing on the DVR. One of the primary reasons could be a wrong or defective recorder’s power supply.

That’s it! Your DVR NVR should now have a new hard drive installed, allowing it to store more video footage. Follow these steps carefully and seek additional assistance if you encounter any difficulties.

How to adjust my DVR NVR monitor resolution?

Camius video surveillance DVR NVR camera recorders have HDMI and VGA video output to live video feed on your monitor.

VGA output supports a max resolution of 1080p, while the HDMI video output 4K video resolution. So if the monitor you use with the Camius DVR or NVR recorder is capable of 4K and the camera, you can view live videos in 4K.

TRIVAULT4K2168R

How to adjust my DVR NVR monitor resolution? 19

IPVAULT1128PR

Two ways to adjust the DVR NVR monitor resolution

You can adjust the DVR NVR monitor resolution in the Wizard Setup mode or by navigating to Setup >> System >> General >> Output Configuration.

While in ‘Wizard Setup’ mode, choose an output resolution that matches your monitor. The DVR should adjust the output resolution automatically to match the best resolution of your monitor at the system startup. 

Please note that some legacy monitors could fail to communicate their acceptable resolution. In this case, please manually plug the video surveillance DVR into a newer monitor and change the resolution to the lowest setting, then save and plug the older monitor back to see if it’s supported.

After completing the Start Wizard, you can further adjust the Display Output Resolution using the following Menu Path: Setup – System – General – Output Configuration.

Select the output resolution suitable for your TV/Monitor. 1080P(1920 x 1080) will suit most monitors. If your DVR supports 4K output resolution, you can select either 2K (2560 x 1440) or 4K (3840 x 2160) to take advantage of the higher resolution that your 4K TV provides.

You can also adjust the size & position of the display screen to match your monitor/TV by using the ‘Scale and Offset’ feature; click the tab ‘Setup,’ which allows you to:

Click once or long-press the left button of your mouse on the arrow to adjust the size and position, or you can scroll the supplied USB mouse’s wheel to adjust. Click the right button of your mouse to exit, and click Apply to save your modifications.

How to reset the DVR and NVR video recorder to default factory settings

To reset DVR or NVR to default settings, navigate to the left bottom of the screen to the main menu. Select Setup >> System >> Maintenance >> Load Default

Here you can select the setting you wish to set to default. If you do not wish to reset the password, do not check the System boxes. Please note Load Default settings do not format your hard drive.

You’d need to enter the system password in the Authentication pop-up window (picture 1), which will lead to restarting your recorder (picture 2).

Picture 1

Picture 2

Navigate to Setup >> System >> Maintenance >> Reset Settings (Picture 3), where you can not select settings to reset so that it will reset your system completely, including the login credentials. You can choose ‘Format HDD‘ if you wish to format your hard drive, leading to erasing any recorded footage.

Picture 3

How to change your DVR and NVR password and add a user

You can update the ‘admin’ password by clicking the ‘User Edit’ button. You will need the admin’s current password to authenticate the new password.

Camius NVR and DVR recorder have an advanced user management feature to add multiple users to the system and control their permissions. System administration (admin) can add users, edit their permissions and delete them.

Navigate to the Main Menu in the bottom left corner, select System >> Multi-User (picture 1)

Picture 1

How to add a user to Camius NVR or DVR recorder 15

Click on the Edit icon in the User Edit column and select ‘Enable‘ in the User Enable tab. You can change the User Name or keep it as ‘user1‘. Create the new user password, confirm it, and click on the ‘Save‘ tab (pictures 2 and 3)

Picture 2

Picture 3

Then click the gear icon in the last Permission column to open the User Permission dialogue. Select (tick checkbox) the permissions you wish to grant to the new user. Click Save (picture 4)

Picture 4

How to troubleshoot if my DVR is not powering on?

If you’re having trouble with your DVR not powering on, here are some recommended troubleshooting steps:

Step 1 – Check the LEDs on the front panel, a steady green LED (PWR) means your DVR is powered on normally, and a blinking red LED (HDD) means ongoing recording on the hard drive. 

8 channel DVR

16 channel DVR

.

Step 2 – Check the sounds coming out of your recorder. A faint fan sound and a faint hard drive sound are normal, and a click sound when you plug in the DC connector and turn on the switch is typical.

Step 3 – If you have the green LED on but no output on the monitor, follow these steps:

Step 4 – Check the power outlet and the power supply unit of the DVR. If the power supply doesn’t have any LED indicator or the LED light is very faint and not bright green, and there is no fan sound coming from the DVR, the power supply may need replacement. If your DVR has running hardware warranty, please contact us. If the DVR is covered with warranty, you can order a new power supply on Camius site.

Why can’t I access my Camius IP cameras, DVR, and NVR on my Camius View app? 

If you can not access your Camius IP cameras, DVR (digital video recorder), or NVR (network video recorder) on the Camius View smartphone app, please check the below:

1 – Check if you are using the latest version of the Camius View app

On the App’s ‘Devices‘ page, make sure your recorder is added using P2P (ID) instead of IP (IP Address), and if in doubt, delete it and add it again.