Our IP camera can connect directly to your network or computer, and there are three ways to do so. The three ways listed below do not require a NVR. A NVR, or Network Video Recorder, is the device that IP cameras connect to.  The NVR records video provided by the IP cameras to a hard drive, either in HD (720p, 1080p), 2K HD, or Ultra HD (4K) depending on the type of NVR and type of camera that’s being used with it.

IP cameras are network-based cameras, however they don’t require Internet access in order to be used as they are standalone devices that can be used on a local network. A simple local network can be either of the following:

1.An IP network camera connected with a network cable to your desktop computer’s network port.

2.An IP camera connected to a router that is connected to a desktop or laptop computer, but the router is not connected to the internet.

Only if you want to view your system remotely from the internet then you would have to connect the system to the Internet.

Do I need a NVR for my IP security camera system?

A NVR is not necessary in order to view your network cameras or even record video. If you are testing cameras, looking for a temporary setup or want to set up something inexpensive then using a computer with an IP camera is a good alternative to a NVR.  SmartPSS is our computer software program that allows PCs to view and record IP cameras. However, this kind of processing will demand a lot from the computer. Most likely, you wouldn’t be able to use that computer for personal use as it would be bogged down processing video from high resolution IP network cameras.  Also, computers can be unreliable and crash, potentially leaving you with no recorded video.

NVR products are standalone devices using a Linux operating system which is known to be rock-solid and crash free, and designed to be operate 24/7 and maintain system security with user account access permissions. For a complete security camera system, you will want to use a NVR along with cameras. SmartPSS software can be used as a client software to connect from a computer to a NVR to watch cameras connected to the NVR and to playback/download recorded security footage.

How to Connect IP Camera Guide 2024

Three ways to connect an IP camera to a computer

Before we begin, it is important to understand that network camera systems require the ability to transport video and power to work correctly. Power Over Ethernet (PoE) is a technology that transmits video/data signal and power over one Ethernet cable. In situations where PoE isn’t available, a 12V DC power adapter will be necessary to supply power to the camera.

Secondly, you will need to use our IP finder Config Tool to find cameras on your network. For more info on basic networking knowledge as to how IP addresses matter when deploying network cameras, please read our guide about connecting security cameras to the internet.

Now, let’s discuss the three ways to to connect to an IP camera from your computer.

1.12V DC power adapter with a network cable straight into a PC

2.12V DC power to camera + network cable to router

3.Camera to PoE Switch or PoE Injector

How to Connect IP Camera to Computer

1) 12V DC power adapter with a network cable straight into a PC

a) For this method we will provide power to the camera using a 12V DC 1amp power adapter that plugs into a 110V AC outlet. Below is a picture of our trusty power adapter.

b) Next, connect a network cable from the camera to your computer.

c) Set your computer’s network port to a static IP address like 192.168.1.200 so you can talk to the camera. Here’s how you do it on a Windows Computer:

d) All newer cameras with firmware from 2018 and onward have stringent password rules that require initialization before making any configuration changes to the camera including the IP address. In order to set the password and password recovery email address you must login to the web interface of the camera. Be sure to note down and keep the credentials you are setting in a safe place that you will remember.

There are no master reset passwords for our equipment. If you forget your password, recovery email address, and security questions that you set on the camera at time of initialization, resetting the camera requires factory service which will incur out-of-warranty costs to reflash the camera.

.

e) Once you have a static IP address assigned to your computer’s wired network port, turn off WiFi on your computer. You can find the camera’s current IP address by using the Config Tool as shown. Our test camera has a current IP address of 10.1.1.65. If you need to change the IP address to let’s say 192.168.1.120, you can do that by clicking on the pencil icon to edit.

Note: if you have a password other than admin set on the cameras, then you will need to enter that in the “search settings” options before attempting to edit the IP address. See the illustration below on how that is done.

f) As explained in our article connecting security cameras to the internet, for two devices on a network to talk to each other, they must have the same IP address scheme. In 1C we set our computer’s address to 192.168.1.200, so we need to set change this camera’s address to 192.168.1.X where X is a number between 2 and 254, and not same as the our computer’s current address. We picked 12, so below is a screenshot of what to set your camera’s ip address to if you are following along in our guide. Set the subnet to 255.255.255.0 and gateway to 192.168.1.1.

g) After changing your camera’s IP address to one that matches your network, type the new IP address of your camera into the URL of internet explorer. Here’s a brief example:

You can also view the camera using our PC software. If you don’t already have it, you can download SmartPSS from here. Here’s how if you already have SmartPSS installed.

In summary, the above is a quick and easy way to connect an IP camera to a computer with a hardwired network port. This is great for the following scenarios:

• You don’t have a router and want to set up a closed circuit system between a computer and a security camera.

• You are trying to test an IP camera or troubleshoot it.

• You are trying to connect to a security video recorder directly from a computer.

Most computers have only one network port, so this method can be problematic as it would use up your only network port, preventing you from having a hard-wired Internet connection. The next 2 methods will demonstrate how to set up a network camera on a network. Method 2 is for setting up a camera with a 12V DC power supply and Method 3 entails using a PoE injector or switch. The only different between these two methods is how power is supplied to the camera.

2) 12V DC power to camera + network cable to router

This method will show you how to connect an IP camera to your router and view it over a network, while supplying power to the camera using a 12V DC power adaptor.

a) Connect a 12V DC power supply to your camera and connect the power adaptor to the wall to power the camera.

b) Connect a network (Ethernet) cable from the camera to the router to establish a data connection between the camera and the router.

c) Give the camera about 2-3 minutes to boot. Use our IP Finder Config Tool to find the camera on your local area network (LAN).  Below is a screen shot of how it looks in our case.

The camera currently has an IP address of 10.1.1.65. As explained in our article connecting security cameras to the internet, for the camera to be reachable from the computer on your network, its IP address has to match the IP scheme of your network. In our case our router IP is 192.168.1.1, so we are going to have to change the IP address of the camera. To change the IP simple press the pencil icon to edit.

d) We are going to set the camera to an IP of 192.168.1.X, we chose 192.168.1.12. Before we go ahead and change the IP address, we have to think about duplicate IP addresses on the network which would create networking issues. To see if a specific IP address is available on your LAN, use the command prompt in Windows to ping the address you intend to use. Below is a video explaining how to use the ping command. You can use this command on Mac as well by using the terminal.

e) Let’s change the IP address. In our case we set it to 192.168.1.12. Subnet mask is usually 255.255.255.0 on simple networks, and the gateway is the IP address of the router. Press OK.

f)  Once the camera is assigned a new IP address, you can access the camera using your Web Browser or SmartPSS as shown in 1F above.

3) Camera to PoE Switch or PoE Injector

We discussed that PoE supplies power to the camera, so a 12V power adapter is not necessary in this scenario.

In this method you plug an ethernet cable from the camera to a PoE port on a compatible PoE switch or injector. The PoE switch or injector connects to the router.

Here’s how you connect to a PoE switch.

Here’s how you connect to a PoE injector

Again, use the Config Tool to find your camera’s IP address and change it to match your network scheme (if necessary) as described in steps 2C thru 2E. Once the camera is on the same network as your computer you can login and watch the camera as shown in Step 1F.

.

Summary

At this point, you now should know a good amount about networking and have used the above mentioned steps to make your very own IP camera system using your computer and IP camera.

Viewing an IP Camera on a Smart TV

Among the many different ways that security cameras are used, we are often asked if it is possible to view an IP camera directly on a Smart TV without using a NVR recorder. With most Smart TVs on the market there is no application that is available to watch IP cameras directly on the TV. In this guide we show how to use an Android TV box by downloading an App to connect an IP camera to a Smart TV or any monitor that has an HDMI input.

All IP cameras from CCTV Camera World support a RTSP video stream that is usable by third party programs and apps. The App that we suggest you use on an Android TV box is called VLC Media Player. You can login and access the RTSP stream from an IP camera and have it display on a TV.

Keep in mind any device that can download VLC Media Player can do this process like iPhones, iPads, Android tablets, and phones.

What equipment is needed?

Here’s the list of all the equipment that is needed to connect an IP camera to a Smart TV.

1.IP camera from CCTV Camera World

2.PoE injector or 12V DC Power Adaptor to power the camera

3.Network cables to connect the camera to your computer network

4.Android TV Box from any online shopping marketplace

5.Computer network to connect the camera and Android TV Box

6.Internet connection to setup and install Apps on the Android TV box which can later be removed after the setup process is finished

7.SmartTV or Computer Monitor with HDMI input

.

How to connect IP security cameras to an Android TV Box

Before you can access the stream from the camera you will need to have it connected to your computer network and verify that it’s accessible. If you purchased a standalone IP camera from CCTV Camera World the camera is likely already configured with an IP address. Check the top of the camera box for the login information label. If the camera has not been configured, or you need to set it up on your network we recommend following our How to Connect an IP Camera guide.

You will also need to set up your Android TV box on your network, consult with the manufacturer of your box to find out how to do this.

You will need your IP address, username, and password that is set on the camera in order to access it. Inside of the VLC Media Player app you can access network streams. Inside of the app navigate to adding a video source and select network stream. Using the example RTSP stream below plug in the information for your camera’s IP address and type the text into the media player URL.

rtsp://192.168.1.109:554/cam/realmonitor?channel=1&subtype=0

After you’ve typed in the correct RTSP stream for your camera you will be required to login to your camera stream. Type in the username and password for your camera to allow the app to login to your camera stream.

If you receive an error, double check that your camera is connected to the network and you’ve typed the correct username and password. Provided the camera is set up on the network and you are able to login you should now see your camera stream inside of the VLC Media Player App.

Keep in mind that Smart Camera features cannot be used with the RTSP stream. If you would like to use Smart Detection features that your security camera may have, you will want to use an NVR to display the camera on your TV.

Watch our video below that shows the setup process described above on an Android TV box.

.

.

Unlimited Access Anywhere, Anytime

When you combine our “Blue Line” IP Cameras with one of our compatible IP camera network video recorders you can keep an eye on your assets no matter where you are. Take advantage of the free remote viewing app to view on your cell. Use the free software to view and control you cameras on your tablet, or computer. Stay connected and have peace of mind knowing you can monitor your cameras remotely, without any additional monthly fees.

LATEST FIRMWARE UPDATES FOR YOUR DEVICE

UPDATING YOUR SECURITY CAMERA FIRMWARE

Firmware Updates

In order to do a firmware update you must first identify the EXACT model number of your DVR or NVR unit. The model number can be found on the sticker located on the bottom or side of the unit. All CCTV Security Pros model numbers begin with the prefix “CSP” (Example, CSP-XXXX). Please match your model number to the list provided below. You will also need to locate your order confirmation email to determine when the unit was purchased. Once you have identified the correct model number and firmware please continue by following the instructions below.

Blue Line IP Camera Troubleshooting v2

Upgrading Your Firmware

Please identify the correct model from the list of firmware provided below.

Please select the appropriate link and download the .bin file. Once the download is completed copy the .bin file to a USB Flash/Thumb Drive. We suggest formatting your USB drive to FAT32 before attempting the update.

**Note : Units with Build Dates of 2013 or earlier may require you to rename the file to “update.bin” before launching the upgrade.

Once the .bin file has been transferred onto your drive you can insert the USB Drive into either of the two USB ports found on your unit. One can be found on the front panel and one can be found on the rear of the unit.

Once the drive is inserted into the unit go to the following menu:

Main Menu –> Setting –> System –> Upgrade. Click Start. Find and select the .bin file you transferred to the USB Drive and Click Start.

*NOTE – On select models you will need to go to:

Main Menu–> Info –> Version –> Upgrade

The unit will now begin upgrading to the latest Firmware Revision that is available for your device. Once completed the system will reboot. After the reboot we recommend doing the following:

1) Remove the USB Drive from your system.

2) Change your passwords on your “admin” account. For assistance in altering your password please follow this link: https://www.cctvsecuritypros.com/content/pdfs/password-account-settings.pdf

.

IMPORTANT: If you are having difficulty identifying the correct firmware please email us at support@cctvsecuritypros.com with your order number and unit model number.

User Account Locked

Your system will lock itself out when you or someone else has attempted to log into your DVR

with an incorrect user/password combination more than three times within 30 minutes

When this happens you have two options.

1. Wait 30 minutes after the last failed login attempt and try again.

2. Reboot the DVR by using the rear toggle switch or by unplugging.

When the unit powers back on try and login with the default username and passwords.

Username: admin

Password: admin

or

Username: 888888

Password: 888888

If neither of these passwords get you into your system you will need to email us at

Support@CCTVSecurityPros.com

and request a Master Password. Once we can confirm your

account we will happily be able to provide you with the correct login credentials.

Please have your Order Number or DVR/NVR Model Number when requesting a Master

Password.

*Note: The DVR/NVR Model Number can be found on the Bottom or Side of your system.

.

IP Camera Harness Repair

If your connector looks like the ones below, moisture has gotten into your RJ45 connector. The number one cause of premature IP camera failure has to do with improper weatherproofing techniques. If caught early enough a simple cotton swab and rubbing alcohol will clean that connector right up! You may need to resort to some heavier duty electrical contact cleaner if the cotton swab method does not work.

If all else fails and the connector is too far gone and cleaning it will not work, you will need to perform a harness repair.

.

In order to perform the repair you will need:

.

.

1 x RJ45 Crimp Tool1 x Male RJ45  1 x Female to Female RJ45

Connector

.

1 x Your choice of weatherproofing ( Weatherproof junction box or weatherproof Female to Female connection)

.

.

Start by removing the RJ45 end off of your IP cameras harness. Be sure

.

Strip back the outside insulation to expose the internal cables.

.

Organize the cables to match the pinout of the IP camera. Slide the organized cables into the connector and crimp. All CCTV Security Pros IP cameras will use this pinout.

Connect your Female to Female RJ45 connector to check your work, you should have a functioning IP camera now that its void of all corrision.

Now that the IP camera has been repaired we still need to weatherproof this connection. It is now more vulnerable than ever!

Consider using a weatherproof junction box to make your connections in, or perhaps a weatherproof Female to Female connector.

Remember that different coupling styles exist so make sure that you are informed about how to use the coupler before you start crimping wires.

Troubleshooting Steps 4/8/16 Channel

(Cannot Find the Network Host)

To solve the error, please verify that the camera is properly plugged into the back of the system. If you unplug and re-plug it back in this should verify it is connected physically.

If the issue continues go to Main Menu > Camera > Camera List and delete the camera with the red status from the bottom list and do a Device Search to verify the camera is showing up on the top list.

If the camera does not show up this means the cable is not connecting properly, which could either mean the camera is not getting power or isn’t transmitting data. The best way to determine whether it is an issue with the Camera or Cable is to bench test the camera on a known working cable.

If it does show up but it has a different IP Address, please confirm the IP Address is in the 10.1.1.1-255 range (This is the default range of the internal Switch).

If the camera is not within the correct IP range, then the camera could need to be modified on the top list to properly connect in which you would select the camera, hit modify, type in the camera’s username and password and set the IP address to DHCP to automatically obtain an IP or statically assign the camera an IP address to match your switch range and gateway.

If the camera is on the correct range, you should be able to add it to the bottom list and it will come up with Green or Red, If Red double check the error message on the live view on the system.

If the Error says Invalid Username or Password, go back to Settings > Camera > Camera List and modify the camera at the bottom of the list and type in the correct login information.

If the error says Cannot Find the Network Host, check the IP Address is in the correct range, if it is you need to verify your cable is good by testing the camera with another known good cable or testing on a short patch cable as the cable could be experiencing packet loss.

Make sure the cable is T568B Standard and is within 100 meters (328 feet.)

Night Vision Issues

When a camera goes into night vision mode, the infrared LEDs around the lens turn on. If the video signal at nighttime or in dark locations is washed out, foggy or you see “halos” on the screen it is because the infrared LEDs are reflecting back into the camera lens.

cameras LEDs to focalize on the mounting surface and greatly reduce the Infrared distance.

Adding 3rd Party Cameras to Blue Line NVR

We always recommend using Blue Line IP cameras with our Blue Line NVRs for the easiest and most complete experience possible. However, we understand that using 3rd Party Cameras can be beneficial in some applications. This guide will explain the basics of adding a 3rd Party IP camera into your Blue Line NVR.

Information you will need to add 3rd Party Cameras.

With your camera attached to one of the PoE ports on your NVR, you’ll navigate to the camera settings from the main menu.

A 3rd Party Camera normally will not add itself, so you will need to go into the Camera List and click on Search Device. If the camera is detected, you will be able to select it and click on the Modify IP button toward the middle of the screen.

When modifying the IP address of the camera the default IP range for the PoE ports on the NVR is

10.1.1.xxx so you’ll want to make sure the camera is on the same range.

You will need to know the camera’s password to change the IP Address. Once the IP is successfully changed it should update after clicking Search Device again

Check the box to the left of the camera and click Add. Most cameras will show up with the Manufacturer as ONVIF. If they do not and show up as red, you will need to click on the edit button on the camera and change the Manufacturer to match the camera’s manufacturer, or to ONVIF if the manufacturer of the camera is not listed.

While in the modify window you can also enter the password for the camera in the password field. Once that is completed you can click OK. After a few seconds the status should change to a green icon and then you should be able to see the camera’s live view. Please keep in mind that if the Error Message says Invalid Username or Password you may need to login to the camera from the Web and setup an Onvif User for the system to login with.

If the camera is still showing offline, setting the manufacturer to PELCO can sometimes resolve the issue.

Additional 3rd Party Camera Information

DVR/NVR Rebooting

If your DVR or NVR is rebooting by itself please read the guide below.

If your DVR or NVR is rebooting once a week this is completely normal. Our DVR and NVR systems are designed to reboot once a week (Tuesday at 2AM by default).

If your DVR or NVR is rebooting more frequently you first want to check the power source of the DVR or NVR.

Be sure you are using the correct Power Source that was included with the DVR or NVR. Below are the correct power adapter specs so you can identify the correct one.

NVRCUBE = 12V, 2.0Amp NVRWIFI = 12V, 2.0Amp

LITE Series DVR = 12V, 2.0Amp

Pro Series DVR = 12V, 5.0Amp

Pro Series NVR = 3 Prong Power Cord to Power Outlet Extreme Series DVR/NVR = 3 Prong Power Cord to Power Outlet

If you can confirm you are using the correct Power Adapter you may need to double check the outlet you are plugged into. Try an alternate outlet and eliminate any Battery Backup Power Supplies for test purposes.

If the power source is not causing the reboot cycle it could be related to the internal hard drive. To check this out please continue reading.

First you will need to Power Off the DVR. We suggest powering the system down from the Power Switch on the rear of the system or by simply unplugging the Power Cable.

Once the system has been powered down you will need to open up the system. Please see below to locate the screws that need to be removed.

NVRCUBE or NVRWIFI

There will be 4 Phillips head screws located on the bottom of the system. Once the screws are removed the top cover will lift off.

Lite Series DVR

There are 2 Phillips head screws located in the rear and 2 on the side of the DVR, 1 on each side. Once the screws are removed the top cover will lift off.

Pro Series DVR/NVR

There will be 4 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Extreme Series DVR/NVR

There will be 2 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Once the top cover has been removed it will expose the Hard Drive and its connections.

First we want to Unplug the Large Black Connector. Press down on the metal tab and pull the connector out of the Hard Drive.

Now we want to unplug the second smaller connector (Blue Cable) from both ends. Press down on the tab and remove from the Hard Drive as well as the System Board.

Once the connections have been disconnected. Plug them back in securely and listen for the metal tab to click. This will ensure a good connection in between the System Board and Hard Drive.

Note*

While you still have the system open, it might be a good idea to check the cooling fans for any dust or debris that could be stopping the fan from moving. This could cause the DVR or NVR to overheat.

Once the connections are tight, lets put the top cover back on. When the cover is back on you can proceed to power on the system. Once the system is powered on you will need to monitor the system and check if it is still rebooting.

Disconnecting The Internet

If the system is still rebooting you may want to disconnect it from your Router or Modem by unplugging the Ethernet cable in the rear. You will loose your remote viewing capabilities temporarily while unplugged but can help us diagnose the issue.

With the cable unplugged you may want to monitor the system closely to see if this has made any changes to the rebooting issue.

Disconnecting Cameras and Other Sources

Disconnecting cameras, alarms, extra monitors and microphones is the last thing we can try to solve your rebooting issues.

Cameras, monitors, and microphones mounted near high voltage could be causing your system to reboot by itself. If your system detects any incoming voltage or amperage coming into the rear inputs the system will shut down to protect itself from damage.

Leave your main Display Monitor and Power Source connected. Disconnect one input at a time to see if it makes a change in your reboot cycle. If you notice a change in the rebooting you can single it out by using this method of elimination.

Get Started with Verkada Intercom Set up and connect your Verkada intercoms Updated over a week ago

Required. You need Org Admin and/or Site Admin permissions for your Verkada Command organization to complete these actions.

What you need

Create a site

Sites are the logical way of grouping and managing devices within your Command organization. Site-level permissions make managing and viewing your devices easier. See Manage Your Sites and Subsites for more information on site creation and management.

Add an intercom

At least one intercom needs to be added to Command before you can see the Intercom tab in the All Products menu. Intercoms can be added to Command from the Devices page. See Add an Intercom to Your Site for more information.

Connect a door

You can pair an existing access-controlled door or wire a door to the intercom that can be unlocked by an intercom receiver. See Configure a TD52 and Wire a TD52 Video Intercom for more information.

Configure receivers

Receivers allow you to answer calls from an intercom and unlock any associated doors. See Add and Configure Receivers in Intercom for more information.

Licensing

Every intercom you manage in Command will need a license. Verkada licensing is applied for each Command organization, and the licenses co-term to a single expiration date. Your licenses may have been automatically added if you claimed your devices via order number. Otherwise, manually add the licenses from the Admin page. See Manage Your Licenses for more information on adding and managing licenses.

Connect your intercom

Recommendation. While Verkada intercoms are considered low-voltage devices that do not require a certified electrician to install, we strongly recommend you work with a system integrator or other professional for installation.

Please refer to the intercom setup guide for instructions on mounting and wiring the door port.

Power and network

Verkada intercoms use Power over Ethernet (PoE) for power and communication over the LAN. In most cases, intercoms will connect directly to an 802.3af PoE standard switch. PoE injectors can be used when a PoE switch is not available. See the intercom’s datasheet for more information.

Check network settings

Verkada intercoms are designed to be plug-and-play. However, if your environment includes a firewall with custom rules and policies, you may need to make some configuration changes to get your access controllers connected to the cloud. See Intercom Network Settings for more information.

Roles and Permissions for Intercom

Roles and Permissions for Intercom

Learn more about Verkada Intercom roles and permissions

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Intercom.

Verkada intercoms setup guide v1

Verkada Intercom permissions determine who can receive calls, view intercom video, and unlock intercom doors. Intercom permissions depend on your site-level permissions, and whether you’re configured as a Receiver.

At a high level, these are the permissions granted to each level of Intercom devices:

Site-level roles

Receiver

Required. You must be configured as a receiver to receive calls.

If you’re a Verkada Intercom Receiver, you have the baseline receiver permissions (as shown above). These baseline Receiver permissions combine with site-level permissions to determine overall intercom permissions within a certain site.

For example, if you’re a Receiver for a particular intercom, and a Site Viewer, you get all the Receiver permissions, in addition to the ability to view historical video and events.

Note: Receivers, such as Desk Stations and Session Initiation Protocol (SIP) phones are not tied to a Verkada Command user. This means that the user can only get Receiver permissions, regardless of the user’s site-level permissions.

Regardless of their site-level permissions, a Receiver can:

Live-View Only

Site Viewer

Site Admin

.

Verify a user’s eligibility to receive Verkada Pass calls

.

Set Org Admin permissions

Revoke Org Admin permissions

.

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Intercom Network Settings

Intercom Network Settings

Learn about the required network settings for Verkada Intercoms

Updated over a week ago

This article outlines the required network settings that your Verkada Intercom needs to communicate with Verkada Command. For more information on the required network settings for other Verkada product lines see Required Network Settings.

Note: Verkada devices are incompatible with LANs that require proxy servers or Secure Socket Layer (SSL)/Transport Layer Security (TLS) inspection. If either is in use, a bypass for all Verkada devices must be implemented for Verkada devices to communicate with Verkada Command.

Status LED

A flashing blue status LED on the top of the intercom indicates the intercom is not communicating with Command. If you see this behavior, check that the network is set up correctly with the intercom’s requirements. If the problem persists, contact Verkada Support.

IP address

Intercoms must be assigned an IPv4 address to communicate on the LAN and to Verkada Command. Intercoms use Dynamic Host Configuration Protocol (DHCP) and User Datagram Protocol (UDP) to obtain their IP addresses and network configurations.

If you require your intercom to have a specific IP address, create a DHCP reservation using the device’s Media Access Control (MAC) address (found on the device’s label).

Domain Name System

Intercoms use the DNS server to resolve Verkada’s fully qualified domain names (FQDN) to IP addresses to communicate with them. Your DHCP server tells the intercom where the DNS server is on the network and the intercom communicates using UDP port 53.

Note: DNS over HTTPS (DoH) is currently not supported.

Power

Intercoms are powered through Power over Ethernet (PoE). This means the network switch needs to provide power to the intercom, or a PoE injector needs to be utilized. For specifics on power requirements, see the Intercom datasheet.

Firewall settings

Intercoms require access to many endpoints to ensure they can communicate with Command and all features will be accessible. Many customers may want to allow the intercoms to communicate with the general required endpoints.

These are the general domains to allow, applicable for all organization-regions:

Region: United States

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Region: Europe

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Mount a TD52

Mount a TD52

Learn how to mount the Verkada TD52 Video Intercom

Updated over a week ago

Use this article to learn how to mount a Verkada Intercom (TD52). Once you complete the mounting, you can connect the TD52 to the network.

Before you begin

You can mount the TD52 using a flush mount or using a mounting bracket. We recommend that you verify the contents of your box and make sure you have the tools you need

Contents of your box

Tools you need

Choose your mounting option

Whichever mounting option you choose, you should remove the front cover of the TD52 to access the screw holes that allow you to install on a mount.

Use a flush mount

The TD52 comes with a flush mount in the box. You can use the screw holes of the flush mount to mount the Intercom (see image below for visual):

Mount directly to a wall

Use a mounting bracket

You can use the mounting bracket to install the TD52 on to various surfaces that the flush mount plate cannot, where they’re typically used to mount the TD52 on an exterior surface.

<< Click on the page numbers to go to other pages. >>

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

How do I access the cameras on my computer?

Go Here, login using with the credentials you used to sign up with. You will see your devices at the top, click ACCESS and it will launch a new tab for that device. This info can also be found by going to our website and downloading it Here 

How do I network the unit so it can be viewed remotely?

First you want to make sure you plug the unit into your router. Now on the unit login, then right click on the mouse and go to Menu> System> Network. You can set the IP Address under “TCP/IP”. Once you’ve entered your IT information go to “P2P” across the top. Make sure it is enabled. Below you will see the server address Here. You will go there and create an account then link the unit with your account. See Link below for more detailed instructions. Here

How do I connect a third party camera?

You will need a PC and the manufacturers IP tool to address the camera(s) IP address within the same scheme as the internal NIC of the NVR (172.16.0.x). Now go to the camera management within the NVR, switch the port that the camera(s) are plugged into from PNP to IP address, protocol will be ONVIF, port will be 80 (HTTP port of the camera) and type in the username and password of the camera and it should connect. Some manufacturers require ONVIF to be enabled within the camera before adding to different unit. Please check their website for information on how to enable ONVIF.

Why can’t I use Chrome, Firefox, Edge or Safari to view my device(s)?

Chrome, Firefox, Edge and Safari took away a plugin that was used for ActiveX plugins. This has effected anyone that uses an ActiveX plugin for their devices not just InVid.

Why is my Vision camera not connecting to the NVR?

That may be due to the NVR having the old default password of 123456. Leave the camera plugged into the unit and go to Menu>Camera then click on the “cog” (gear looking icon) next to the port of the camera you are trying to connect. Type in the password “1234567u” for the camera and the camera should then connect.

Why did my device suddenly go offline?

If you are connected to your ISP’s router (Internet Service Provider) occasionally it is possible your ISP is doing a update which can occasionally change your network environment and require a reboot of your router/recorder (Router first then recorder). It is highly recommended that with this device to install your own router to run the recorder to avoid this from happening, however if using your ISP’s router the above stated solution is the fix for it.

How do I Share a device added to my star4live account?

Have the new user create an account Here. Log into the account with your device, click on SHARE, enter in the customers user name or email, choose a “valid to date”, when this date hits the device will no longer be shared, and hit ok. The device will now be found under the Shared Record. This info can also be found by going to our website and downloading it Here

Trying to view devices on IE but can’t download the plugins?

Please ensure you are in fact using Internet Explorer and not Edge. The two have similar icons, Edge is a darker blue lower case “e” whereas Internet Explorer is a lighter blue lower case “e” with a yellow ring going over the top left of the “e”. Also note that on Windows 10 Edge is the default browser, Internet Explorer isn’t on the task bar or the desktop, you can use Cortana and search “Internet Explorer” to launch.

How do I turn On/Off motion function?

Right click on the mouse, go to the menu>alarm>motion. By default motion detection should be enabled. You want to draw the area of where you want motion to be detected and then hit apply down at the bottom.

How can I see video from last week?

To playback video you want to right click on the mouse and the second to last option on the bottom is “Playback”. On your right you will select which cameras you will like to playback, below the camera list select the date in which the video was recorded. Hit the play button down at the bottom and the playback should start.

How do I add a User?

Right click on mouse go to Menu>System>User. Click Add at the bottom. Create the username and password then select permissions you want to grant that user and hit OK.

How do I format my hard drive? Vision Series

Go to Menu, click on Storage, click on Hard Disk, select your disk(s) and click Format (remember, this erases all data on that drive(s)).

Do I need to port forward this device? Vision

If you’re using the P2P which is explained above no port forwarding is required, if you are networking this device to be seen remotely via a WAN IP or DDNS, yes port forwarding is required.

Is there a manual for this device?

Yes, you can find it on our website Here

Where can I check to see if my unit is recording?

The best way is by doing a playback (refer to question above). You can also go into the Menu, select Maintain on your left and Recording across the top.

InVidTech Vision Series Setup Guide v1

How to Setup Vision Email Notification

Learn how to setup email notification on your Vision machine

Step 1: Setting up a GMAIL account.

1. Go to My Account setting page, click on the square and click my account.

2. Click Signing in to Google.

3. Click Allow all less secure apps on

Step 2 – Setting DVR/NVR Configurations

Enabling Motion Detection

Hit Apply to save then OK

What is the default password of the Vision devices?

We provide a sticker on the inside of the boxes, whether it’s a DVR Encoder, NVR or IP Camera. The default user name and password could be either “admin/123456” or “admin/1234567u”. Once the change-over is fully complete they will all be “admin/1234567u”

How to Setup Vision P2P Using the QR Code

With P2P QR connection there is no need to set any ports, worry whether or not your uPnP is enabled within your router, do any port forwarding within your router or setup a DDNS name.

Not connected? Here are some things to check

Viewing your Vision Device Online or from Mobile App

Viewing from your Web Browser (Internet Explorer):

Viewing from your InVid Vision mobile app:

Is my unit up to date with its firmware?

To find out if the unit is up to date Locally, you want to go to the Menu, select Maintain on your left then Upgrade. Now select “Upgrade by Cloud” (across the top) then hit “Check” in bottom right had corner. To find out if the unit is up to date Remotely, you want to go to Setup, then Maintenance then Maintenance again and hit “Check New Version”. If it is the latest firmware it will say “The current version is already the latest.” If it is not up to date then you will be prompted to upgrade, which will download the file from the cloud, upgrade and restart your NVR.

How do you check to see if an upgrade is available for the Vision NVR?

Is it possible to reset a password for a device?

Yes please contact our Tech Support, 631-388-5700.We will need the devices FULL serial number, you can do this at the main monitor or from the web interface.

How do I access the cameras on my phone?

Once you have downloaded the VISION app from the App Store or Google Play store, sign in with your login credentials used when creating your star4live account.Hit the camera icon in the top right hand corner and you will see a list of all devices added to your account.Choose the device youd like to access and hit “Start Live View” at the bottom of the screen. This info can also be found by going to our website and downloading it Here

Where do I download the APP?

-The app can be found at either the app store for an Apple device, or the Google Play store for an Android Device, you want to search “Paramont CMS”. This info can also be found by going to our website and downloading it Here 

What App do I use for my phone?

InVid Vision

How do I view my device(s) on my Mac?

The current work-around is to install the appropriate CMS software which will allow you to watch live and playback your device(s). You can download the CMS software(s) off our website Here. 

.

Frequently Asked Questions

Note: These guides were written for Uniview NVR users who prefer to change settings remotely using a mobile or desktop browser (Internet Explorer). Remote and local configurations share many similarities and only the locations and availability of each feature may vary. The Uniview NVR Manual can provide more information if what you are looking for is not found in this simple guide or if you prefer local access by connecting a mouse and display to your NVR.

How Do I Access My Uniview Security System?

There are two ways to interface with your Univew Security System and to access all its features and configuration options you can choose to access it locally or remotely. Local access refers to connecting your Network Video Recorder to a display and a USB mouse. The monitor and the mouse will serve as the input-output for interfacing. Remote access refers to connecting to your Network Video Recorder through a browser (Internet Explorer provides the greatest compatibility) installed on a device that is in the same network as the Security System.

Local Access and First Time Setup

The NVR interface can be accessed directly by simply connecting the NVR to a display (this can be done with an HDMI or older VGA cable) and to a mouse. Once the display and the mouse is connected and the login screen is displayed, proceed to login. Since this is the first time, we will be using the default username and password (at the time of writing default login and password are admin and 123456) found on the manual that came with the NVR. 

After logging in, Uniview’s privacy policy will be shown for you to review. Once you have reviewed and accepted, you will immediately gain access to the NVR and cameras connected to it. But, since it is the first time we are logged in and we are still using the default credentials, we will be prompted to change the login information.  You will be using the new password for all your future access with the NVR.

Once the password has been changed, a pattern lock will also be prompted (this is optional and can be skipped). After doing so, the Privacy Policy will be displayed for the user to review. The screen that follows the Privacy Policy will let us connect our mobile devices to the NVR. This will grant access to Live View, alerts, and other configurations we may want.

The device QR code will be presented here. Allowing you access to the EZCloud feature. Devices can be added to the cloud manually but it is far easier to just use a link given from the QR code. If you want to pair the NVR with the EZView app, click here to read more about it. 

The next step is to set or synchronize the time. This step will ensure that all scheduling configurations you will set and all alerts and alarm information will be accurate and will work based on your local time.

After this, you will be prompted to check the TCP/IP settings, the default settings will work for most people. If you need to specify networking (usually when DHCP is not enabled on other devices on the network), please do so here. You will still be able to alter this later.

Once the time and the password have been configured, you are now ready to enable and disable the features of the NVR.

To access the menu, you can right-click on any part of the screen and then click on Menu. It can also be accessed along with other options by moving your cursor to the bottom left of the screen. This will take you to the SETUP screen where you can enable and customize alerts, features, and other options available to you.

Remote Access and First Time Setup

You can also access the NVR interface through the use of a browser on a device connected to the same network as the NVR. To do this, you will need the IP address of the NVR you wish to connect to. The easiest way to find this on a Windows PC is with Uniview’s EZTools which can be downloaded here. Once installed on your computer, running the EZtools will automatically show you all connected Uniview devices.

The IP address can also be obtained by logging into your router and checking connected devices, using the command prompt (arp -a command and checking for new devices on the private network) or simply using another display for the NVR to check the current IP address of the device.

Note: Any browser should work to alter configurations, however using Internet Explorer will be the easiest to access the live view. (due to some newer browsers not supporting certain plugins). 

From here, we can see the IP address given by our router to the NVR. 192.168.254.192. It will likely be different for you. Clicking on the Remote Web button will open your default browser and take you to the NVR interface.

You can then proceed to login to your Uniview NVR Interface. Since this is the first time, we will be using the default username and password found on the manual that came with the NVR. After logging in, Uniview’s privacy policy will be shown for you to review. Once you have reviewed and accepted, you will immediately gain access to the NVR and cameras connected to it. But, since it is the first time we are logged in and we are still using the default credentials, we will be prompted to change the login information. You will be using the new password for all your future access with the NVR.

Once the password has been updated, you will be greeted by the Live View display. Clicking on any of the cameras found on the left will show you live footage from it. In this case, a single IP camera is connected to the 4-Channel NVR.

From here, you can now click on SETUP to access all configurations and features and set them up to your preference.

Uniview How To Guides 2024

How Do I Start Recording And Scheduling?

Once properly installed and powered, most Uniview Security System immediately starts recording and saving footage to the Hard Disk Drive. To configure when and what types of footage you choose to save, you only need to navigate to the Recording Schedule tab.

Navigation: Setup > Camera > Schedule

Pre-Record and Post-Record:

If the Pre-Record and Post-Record values are set to 60 seconds and 300 seconds respectively and using motion detection as a trigger, here is how it will play together:
.

Event-Types:

The setup that is shown on the screenshot above can be interpreted this way. During weekdays, from 7:00 AM to 5:00 PM, the system will monitor and record all footage into memory. The rest of the day, the system will not record anything unless a motion trigger or an alarm event is detected. During weekends, the system will not record anything except for motion-triggered events. During holidays, the system will not record anything unless an event is triggered.

How Do I View Playback, Timeline, and Events?

The Playback tab is found between the Live View and Setup tabs of your Uniview Web-Based Interface. As always, Internet Explorer would provide the widest range of options not available to other browsers.

Navigation: Playback

The playback sidebar is the first point of interest. The top drop-down allows you to filter what types of playback you wish to view. The options are as follows:

Normal: Default playbacks and scheduled recording sessions.

Tag: Shows a playback list that matches a tag keyword.

To utilize this feature, you will need to create tags on certain times you want to save for future reference. To do this, click on the time you want to create your tag and click on the Add Customized Tag button on the toolbar as shown here:

A window will open that allows you to name your tag and adjust the time.

After clicking OK, the new tag will be created. To search for tagged footage, change the filter into Tag, click on the Camera, specify the Keyword, set the time range to search between, and then click search as shown below:

This will display all tagged footage that matches the Keywords.

Event: Shows playback list for a matching event. Very similar to the above example but a simpler approach is only looking for footage of recorded events. To use this function change the filter to Event, choose a specific Event-Type from the drop-down list, select the Camera, specify the Time Range the system will search. Click search. This will display all events that match the Event-Type captured by the camera within the time range.

Smart: The system analyzes recordings for smart search results. 

How Do I Monitor And Manage My Storage?

To monitor and manage your storage, you will need to access the Hard Disk group on the setup. The settings and their functions are explained below.

Navigation: Setup > Hard Disk > Hard Disk

Hard Disk

This tab shows you details of the current storage situation of your NVR. The total capacity and the available free space can be monitored from this tab alongside options to add and more storage.

Disk Group

This tab allows the creation and management of Disk Groups. A handy tool if managing a large number of Hard Disks and to simplify storage allocation.

Navigation: Setup > Hard Disk > Disk Group

The disk group feature allows us to assign hard disks to a disk group and use the disk group to store recordings and snapshots of specified cameras. Different arrays can be assigned to different disk groups. Redundant disks cannot be assigned to any disk group. Disk group information will be initialized if any disk in the group is formatted.

Allocate Space

This tab allows setting a maximum storage allocation for each camera on a disk group.

Navigation: Setup > Hard Disk > Allocate Space

Advanced

This tab will determine what the Network Video Recorder will do once the Hard Disk Drives are full and new footage needs to be saved. Setting this to Overwrite should allow the NVR to delete older footage to make space for new ones to be saved while setting this to Stop will prevent any new recordings to be saved.

Navigation: Setup > Hard Disk > Advanced

How Do I Set Up Tamper Detection?

To set up Tamper Detection, you will need to access the Tampering section of the Camera Setup.

Navigation: Setup > Camera > Tampering

How Do I Set Up Motion Detection?

Navigation: Setup > Camera > Motion

How Do I Set Up Face Detection?

The Face Detection feature creates an EVENT when a person’s face is detected by the Video Content Analysis. It will then proceed to take screenshots of the person or persons detected.

Navigation: Setup > VCA > Face Detection

How Do I Set Up Line Crossing Detection?

The Cross Line Detection feature creates an EVENT when an object crossed a specified line. This feature has 3 modes. A<->B which creates an event whenever an object crosses the line. A->B which only triggers when an object moves from side A to side B. B->A which only triggers when an object moves from side B.

Navigation: Setup > VCA > Cross Line Detection

How Do I Set Up Intrusion Detection?

The Intrusion Detection feature creates an EVENT when an object that meets the minimum size relative to the region (based on percentage) enters any of the specified regions and stays inside the region past the minimum time threshold.

Navigation: Setup > VCA > Intrusion Detection

How Do I Set Up People Counting?

The people counting feature is used to monitor the number of people entering or leaving an area.

Navigation: Setup > VCA > People Counting

How Do I Adjust Image Enhancements, Exposure, Infrared, and Starlight?

Although fully-functional and is configured by default, you can specify desired image enhancements on the Image tab.

Navigation: Setup > Camera > Image

How Do I Adjust Resolution, Frame Rate, Bit Rate, and Video Compression?

Adjusting the resolution, frame rate, bit rate, and compression of recorded footage can be done by navigating to the Encoding Tab.

Navigation: Setup > Camera > Encoding

How Do I Name My Cameras and Manage On-Screen Display?

Navigation: Setup > Camera > OSD

How Do I Directly Transfer Footage From My Security System to My USB?

To transfer footage from the Network Video Recorder to your USB, you will need to create a video clip from the recorded footage, then save it to your USB.

.

The NVR features embedded 16x 802.3 at/af PoE ports to provide users easy and convenient IP camera installation, and also supports remote and mobile access via VIVOCloud and iViewer apps for both iOS and Android devices. The VIVOCloud app provides instant push notification and direct video playback functions when triggered by an alarm notification and provides users a flexible and intelligent NVR for seamless use in small to medium sized video surveillance applications.

Highlight Feature

.

New Web UI Available for Plug-in Free Browser

Actively adopting current trends and simultaneously protecting your cybersecurity, VIVOTEK’s new web UI supports Chrome browsers without the need for web plugins. It lets users login and operate with ease, and solves issues related to system administrator authority, safety risks, browser, and OS updates. Furthermore, it now supports H.265 technology meaning that users can attain higher and more efficient image compression rates than previous H.264 systems while maintaining high image quality.

More

Smart VCA Event Search

The NVR supports alarm management and event search of VIVOTEK’s deep-learning video analytics technology, Smart VCA. The user can search by single or multiple event types, playback triggered events and then export these search results to video clips.

.

PoE Management

Allow users to quickly troubleshoot problems and monitor power use for better operation. When overloaded, some PoE ports will auto power-off until system power is falls below the threshold for system protection.

Integration with Genetec Security Center

VIVOTEK NVR’s are not only fully integrated with our own VMS software – VAST 2, now they are also able to connect with Genetec Security Center via ONVIF, offering various functions including NVR search & add, video/audio display, video streaming configuration, edge playback, and NVR firmware upgrades. With the connection to Genetec Security Center, reliable video surveillance solutions can be delivered to address small, medium, and large surveillance implementations.

Customer Support

Customer support allows VIVOTEK technical support to rapidly debug your NVR, users only need to export logs by pressing one key and providing the logs to the technical support team to get customer support.
In addition, you can get an access ID while connected to the internet. By keeping the remote access button on and providing the access ID to the technical support team, we can remote access your NVR to analyze the cause of errors and then debug it.

Better Video Quality with Lower Bandwidth

With H.265 standard and VIVOTEK’s Smart Stream technology, VIVOTEK NVR is not only able to provide the high quality video, also save the usage of network bandwidth and recording capacity more than regular H.264 standard.

4K IP Camera Video Input and 4K Local Video Output

Supporting 4K IP camera video input and 4K local video output, VIVOTEK’s NVR can provide users extra high definition video resolution ensuring they will never miss a single detail in both video monitoring and recording.

VIVOCloud App & Portal for 24/7 Viewing

The free VIVOCloud app makes surveillance lightweight and portable, ensuring efficient operation. The latest P2P technology makes remote access even more convenient, by simply scanning the QR-code and installing the app, users can view live streams and play recorded clips with the intuitive interface anytime, anywhere. Armed with the Push Notification function, users will directly get an alert message on their Android/iOS mobile device and directly playback the video to check for any suspicious activity.

Vivotek NVR Linux based user guide

Read Also : Vivotek firmware DVR NVR IPC Software download

.

What information of the ND/NV-Series NVR should I provide to contact technical support for help?

Please provide the following information while contacting technical support for help:

We might need the following information, but they are not compulsory:

[Linux-based NVRs] How to upgrade the ND-series NVR?

Enhancing the functionality and security of your ND/NV-Series NVR is crucial, and firmware upgrades play a pivotal role in this process. Please follow the steps below to upgrade the ND/NV-Series NVR:

Before starting the upgrade, it’s recommended to back up your current settings and data to prevent any potential loss.

Step 1. Search for your NVR model on the VIVOTEK official website: https://www.vivotek.com/.

Step 2. Click on the webpage of your specific NVR model.

Step 3. Select ‘Downloads’ to find and download the latest firmware version (for example, ND9425P, as shown in the picture).

Step 4. After downloading, unzip the file to find a .img file.

Step 5. To update the firmware, access the NVR and import the .img file via Settings > System > Maintenance > Update Firmware.

There are two ways to access the NVR: via a Web console or a Local console. Please choose the appropriate method for accessing your NVR.

Web console

Navigate to Settings > System > Maintenance > Update Firmware and follow the previously mentioned steps.

Local console

Firstly, place the .img file on a USB drive and insert it into the NVR.

Then, access the system settings by clicking on the gear icon in the local view.

Once in the ‘Settings’ interface, go to System > Maintenance > Update firmware and proceed as described earlier.  

How to export debug logs and enable remote access function from ND-Series NVR(Linux-based)?

Starts from firmware version v4.1 of ND/NV-Series NVR, VIVOTEK add remote access function on the customer support page.

Please follow the step below to export debug logs and enable remote access* function to get access ID:

There are two ways to access the NVR, please choose which one you access to NVR. 

Web console.

Local console.

Note 1:
1.Remember to provide MAC address of ND-Series NVR at the same time when providing the access ID.
2. Remote access has 14 days validity.

Note 2:
* Important Notice *
The ND9213P, ND9323P and ND9425P NVR remote access service for customer support will be temporarily stopped starting from Feb. 7th, 2022 until the middle of April, 2022 due to service maintenance and firmware tunning. After the proper changes have been done in the cloud platform and the firmware, VIVOTEK will release an statement informing the new NVR firmware v4.1 release and will resume the remote services for those specific models.
For ND9441. ND9541, ND9441P, ND9541P, ND9322P, ND9424P, ND9322P-v2 and ND9424P-v2, remote cloud service will NOT be supported. 

Web console.

• Go to setting>System>Customer support page
(A). Export debug logs.
(B). Enable remote access.(OFF->ON)
(C). Cope Access ID.

Local console.

• Go to setting>System>Customer support page
(A). Export debug logs.
(B). Enable remote access.(OFF->ON)
(C). Cope Access ID.

How to export the backup/configuration file of the ND/NV-Series NVR(Linux-based)?

The NVR backup file contains the device configuration files, usually this file is exported as a security measure in case the device needs to be reset to defaults and then be restored with a predetermined configuration or previous configuration. This file can also be used by VIVOTEK Technical Support in case they require to reproduce an issue (using the same configuration parameters). In order to export the backup file of the ND/NV-Series NVR please follow the next guide:

Chose your interface:
There are two ways to access the NVR, please choose which one you access to NVR. 

Note: If you are planning to provide the configuration file to Technical Support for analysis/troubleshooting please remember to provide the password of the admin account as well.
.

Web console:

Step 1. Using a browser, access the NVR using the username and password.

Step 2. Click on the gear icon to access the NVR configuration page.

Step 3. Click on the “System” tab and select “Maintenance”.

Step 4. In the “Maintenance” interface click on the “Backup” button to export the backup/configuration file of the NVR. 

Step 5.When the download promp appears, click on “Save” to save the backup file to the computer.

Step 6.Be sure that the file was correctly stored.

.

Local console:

Step 1. Prepare and insert the USB into the NVR USB port. You can use either the back panel USB and frontal panel USB ports (if any) to extract the files. 

Step 2. In the Live View interface, click on the gear icon to access the device configuration page. 

Step 3. Go to the system tab, select the maintenance section and click on the “Backup” button to copy the configuration file in the USB. 

How to know the MAC address, model name, firmware version and device pack version of the ND/NV-Series NVR(Linux-based)?

Please follow the steps below to check the MAC address, model name, firmware version, and device pack version of the ND/NV-Series NVR:

There are two ways to access the NVR, please choose which one you access to NVR. 

Web console.

Local console.

Web console.

1.MAC Address:
Please open the Shepherd on your PC to find the MAC address of NVR.
(Refer to How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?)

2.Model name, Firmware version and Device pack version:
Go to setting>Information>Information

.

Local console.

1.MAC Address:
Please find the MAC label on the top of cover or bottom cover of ND/NV-Series NVR.
If there are 2 MACs on the MAC label, please provide us 2 MACs.

2.Model name, Firmware version and Device pack version:
Go to setting>Information>Information

How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?

Question

How to get camera list with camera model name, firmware version and MAC addresses via Shepherd?

Answer

.

Today, Anviz aims to deliver simple and integrated solutions including cloud and AIOT-based smart access control & time attendance and video surveillance solution, for a smarter and safer world.

Part 1. Firmware Update Via Web Server
 

1) Normal Update

>> Step 1: Connect Anviz device to PC via TCP/ IP or Wi-Fi. (How to connect to CrossChex)

>> Step 2: Run a browser (Google Chrome is recommended). In this example, the device is set in the server mode and IP address as 192.168.0.218. 

>> Step 3. Enter 192.168.0.218 (Your device might be different, check the device IP and enter IP address) in the browser address bar to run as the webserver mode. 

>> Step 4. Then enter your user account, and password. (default User: admin, Password: 12345)

>> Step 5. Choose ‘Advance Setting’

>> Step 6: Click ‘Firmware Upgrade’, choose a firmware file that you want to update and then click ‘Upgrade’. Wait for the updating complete.

>> Step 7. Update Complete. 

>> Step 8. Check the firmware version. (You can check current version either on webserver info page or on the device info page)

How to Update Anviz Device

Read More : UNV Recorder Set Up Guide
.

2) Forced Update

>> Step 1. Follow the steps above till steps 4, and enter 192.168.0.218/up.html or 192.168.0.218/index.html#/up in the browser.

>> Step 2. Forced Firmware Upgrade mode is set successfully.

>> Step 3. Operate Step 5 – Step 6 to finish the forced firmware updates.

.

Part 2: How To Update Firmware Via CrossChex

>> Step 1: Connect the Anviz device to the CrossChex.

>> Step 2: Run the CrossChex and click the ‘Device’ menu on the top. You will be able to see a small blue icon if the device has connected to the CrossChex successfully.

>> Step 3. Right-click the blue icon, and then click the ‘Update Firmware’.

>> Step 4. Choose the firmware that you want to update.

>> Step 5. Firmware update process.

>> Step 6. Firmware Update Complete.

>> Step 7. Click the ‘Device’ -> Right-Click the blue icon -> ‘Device Information’ to check the firmware version.

Part 3: How To Update The Anviz Device Via Flash Drive.

1) Normal update mode

Recommended Flash Drive Requirement:

     1. Empty Flash Drive, or place firmware files in the Flash Drive root path. 

     2. FAT file system (Right-click USB Drive and click ‘Properties’ to check the Flash Drive file system.)

     3. Memory Size under 8GB. 

>> Step 1: Plug a flash drive (with an update firmware file) into the Anviz Device.

You will see a small Flash Drive icon on the device screen.

>> Step 2. Login with Admin mode to the device -> and then ‘Setting’

>> Step 3. Click ‘Update’ -> then ‘OK’.

>> Step 4. It will ask you to restart, press ‘Yes(OK)’ to restart once to complete the update.

>> Done  

2) Force update mode

(****** Sometimes devices are not allowed to be updated, this is because of device protection policy. You can use force update mode when this situation occurs.   *****)

>> Step 1. Follow the Flash Drive Update from step 1 – 2.

>> Step 2. Click ‘Update’ to get into the page like showing in the below. 

>> Step 3. Press ‘IN12345OUT’ in the keypad, then the device will change to forced upgrade mode.

>> Step 4. Click ‘OK’, and the device will restart once to complete the update.

>> Step 5. Update Complete.

Summary for Anviz Product’s Firmware

For convenience we made this topic listing all firmware of Anviz access control & time attendance device. You can upgrade your device as necessary.

If you don’t know how to upgrade the firmware, please refer to the upgrade guidances below:

Click to Check Upgrade Guidance Suits ST Platform Device 1.0 bin

ST Platform devices:
T5, T5 Pro, T5 S
M5, M5 Pro
P7, M7
VF30, VP30, VF20
D200
EP300
A300

Get Firmware for ST device：

Click to Check Upgrade Guidance Suits Linux Platform Device 593

Linux Platform devices:
A350, A350C, A380
C2 Pro, C2 KA, C2 Slim
EP30, EP300 Pro
FaceDeep5 Series
FacePass7 Pro
M5 Plus, M3 Pro
M-Bio
VF30 Pro
W1 Pro, W2 Pro

Click to Submit a ticket 467
If you need to upgrade firmware for above device types, please submit a ticket with the serial number, current firmware and kernel version. We’ll send you the correct firmware and help with the upgrading.

If you have any concerns or questions, please submit a ticket 183 and our technical support team will help .

.

Support log in with cloud technology

Support real time live view

Support remote playback

Local recording and play

Support snapshot and pictures searching

Support bidirectional talk

Support PTZ control

Support scanning serial number by QR code

Support cloud user register and modify

Support remote device add, edit and delete

Support local device add, edit and delete

Support adding device by address

Support manually searching device in LAN

Support version updating automatically

Support searching device function by shake

Why can’t live view the videos on mobile APP or PC Client VMS

1.Please make sure that your DVR system is already connected to the router through ethernet cable successfully

2.Please go to Main Menu > System > Net Service to check the network is connected or not, Cloud should shows: connected 

3.Make sure the way you add device to your mobile app or PC client with correct serial number and password

Serial number: “Main Menu–Advanced–Version”

Password: DVR login password 

Hiseeu XMEYE DVR SECURITY SYSTEM ADVANCED GUIDE

Read More : XMEYE DVR User Manual

What should I do If I forgot my DVR password

1.Right click mouse from home screen, Click “Log Out–>Log Out”

2.Then click “Forget password” ＞ “Forget answer ” ＞ Then you will see two “QR code” on the monitor

3.Open your Mobile APP “XMEye Pro” , 

(1). Click the “+” icon on the top right corner—>Hit “NVR”

(2). Click “Forgot your device password”–> Scan the QR code (CAPTCHA on the TV monitor)

(3). Scan the QR code shown on your TV monitor. You will get the verification code.

(4). Input the code in “CAPTCHA”

Add device to mobile APP (XMeye Pro)

As for how to add the device to mobile APP(XMeye Pro), please follow the below instructions

–>1. Please connect the NVR box to your Router via Network Cable;

–>2. Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR is online (Please skip step3), 

.

–>3. If the cloud status shows “Probing DNS”, Please Navigate to Main Menu > Network > Check Enable DHCP–>Apply;

–>Reboot DVR by unplug power adapter and re plug it, then double-check the cloud status. 

.

–>4. Go to your TV Monitor, navigate to Main Menu–>Advanced–>Version–> You will see the serial number. 

The QR code contains serial number info. 

.

–>5. Open the mobile APP “XMeye Pro” and register an account by your email

–>6. Click”+” to add device–>Choose “NVR”

Click the “Scan” icon to Scan NVR’s QR Code. (QR code contains username and password)

No need to input the user name and password manually.

And click “Ok”, and go back to the Device page on App,and you will see the device shows status: online ,

.

Note1:

We do not suggest customers to manually input the serial number, If they input it, the user name and password need to be input, If they scan the code, they don’t have to input the user name and password, So we need to guide them to scan the QR code first, in some situations if we really need the information of the user name and password, and for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

Note 2:

If device shows “offline”, there could be two causes:

(1) DVR is not connected to network successfully, plz go back to Monitor UI Interface to check if the cloud status shows connected or not in the path of “Main Menu > Network > Net Service”

(2) The way he adds the device to the app is wrong, especially some customers don’t know how to find out the QR Code and input the wrong user name and password

Enable the APP push notification on mobile app “XMEye Pro”

1.Please right-click mouse and navigate to Main Menu–> Alarm–>Motion Detect/Human Detect/Face Detect–> Enable “Mobile Reported”–>click “OK” (Default Setting is for Channel 1, Please select “All” channels.)

2.Open “XMeye Pro” mobile App, and navigate to Event–>Device (the one you named)–>Enable “Allow Notifications”

Camera stay in Black’n white during the daytime

It’s a normal situation especially during the switch from night to day, but if the camera keep stayiing in the black and white mode for a long time in the daytime, plz unplug the camera from the DVR port, and replug the wire of the camera into the DVR port to have a try first. 

After repluging the wire of the camera, and if the situation happens again, plz contact us for further support

Add device on PC Client(VMS)

VMS download link:

For Windows （2023 newest version）

https://download.xm030.cn/d/MDAwMDE0OTM=  

For Mac ( 2022 version)

https://download.xm030.cn/d/MDAwMDA2NDA=  

.

1. Download PC Client “VMS” and installed

[ Need to drag the file to the desktop after installing firmware, or it would ocurred the issue of “unable to open archive file”]

2. Login with the default User Name and Password. Click “SIGN IN”.

Default User name is: admin

Default Password is: admin

3. Navigate to “Device Manager”–>”Manual Add”

4. Login Type: Cloud ID

Device Name: Name Your Device as you like

Cloud ID : Device Serial Number. We need to go to the TV Monitor connected to the NVR , and find out the information on TV Monitor UI, then right click the mouse to navigate to the path of “Main Menu–>Advanced–>Version” to find out the information “serial number”

[Note: most customers do not know how to find the serial number, so they can’t add the device to PC Client

User Name and password: Input the user name and password that you created for the NVR , and we also need to find this from the Monitor UI.

[Note: Most customers do not know their user name and password, so we need to guide them to go next to the TV monitor, and right click the mouse from “Log out–Log out”, then right click the mouse and navigate to “Main Menu”, this interface [system login] would pop up]

5. Navigate to “Live View”, Click on the device name(serial number), then select “Open All By Sub Stream”

What if the APP keeps asking the user and password?

Step: Plz input the Monitor UI user name and password to resolve this issue

The cause： Sometimes the APP would be in the process of auto-maintain, so it would ask for the user name and password to protect the account’s safety. This page will pop up when you want to live to view the camera.

Note: Some customers enter the App account user name and password. Actually, it’s the Monitor UI user name and password      

As for how to find out the user name and password, plz go next to the TV monitor UI Interface, and right click the mouse from “Log out–Log out“, then right click the mouse and navigate to “Main Menu“, this interface [system login] will pop up, and here are the user name and password we need to enter into the app

.

Upgrade NVR/DVR firmware

If customers need a firmware upgrade for NVR/DVR, and we need the “System version” to send to XMmanufacturer to ask for a firmaware to upgrade  

Go to Monitor UI Interface, and navigate to “Main Menu– Advanced–Version“

After get the Version:

Please follow the instructions below to upgrade the NVR/DVR firmware. Steps:

Attached new firmware for you, please download it and unzip it.  

1. Copy to your USB flash drive, and put it in the root directory(Do not under any folder)

2. Plug the USB device into NVR/DVR

3. Navigate to “Main Menu–> Advanced–> Upgrade”

> Upgrade position(Select your usb device)

–> Upgrade file (Select the firmware)

–> Upgrade

Unable to open VMS archive file

Please drag the exe file to your Desktop interface (do not under any folder) and run it again.

Like it the photo shows , plz do have a try again ,the VMS will run normally

One or two cameras are not wokring

(1) BNC Cable connected to Camera is broken

Step: Use another BNC cable to connect the camera to have a try

(2) The port of the DVR box is broken

Step: After changing the BNC cable, and still there is no camera image, plz insert the camera into another port of the DVR to have a try

(3) Camera is broken after troubleshooting with the steps （1）–（2）

Network “Probing DNS”?

1. Go to Monitor UI Interface, and Navigate to “Main Menu > Network > Net Service”, if the “Cloud Status” shows connected, means NVR/DVR is online

–>2. If the cloud status shows “Probing DNS”, Please Navigate to “Main Menu > Network > Check the icon of “Enable DHCP”–>Apply; –>Reboot the DVR by unplugging the power adapter and re-plug it, then double-check the cloud status ( only cloud status shows )

How to Sign Up APP Account

Please follow these instructions to sign up for an account via your mobile number.

1. Click on Sign Up

2. Sign Up by email or Select Mobile Number

3. Select the correct country code +1, input your mobile number and click on “Get code”

4. A code will be sent to the mobile phone number, input the verification code and continue.

[Note: You can tap on “Local” for quick login without registration. (In this situation, you still can have live view and playback but are not able to receive motion detect alarm message), so mostly we suggest customers to sign up an account first]

My UI Interface stuck in Hiseeu Logo

We need to upgrade the system to solve this problem, and check customer’s NVR mainboard info first, and take a photo for us to make sure about firmware verison, then we will ask manufacturer to send us a firmware to upgrade the system to solve this problem

1. If you are in the phone call , just let the customer take a photo of the mainboard, and send it to email  We will ask for a firmware to solve this problem during our working time

(Different versions have various firmware, there is no standard firmware to upgrade the system, so we need to ask the original manufacturer to do that)

2. If you are dealing with the email:

Try with the steps:

1. Ask the customer to open the DVR box by using the screwdriver, and take a photo of this mainboard, and make sure the QR Code is clear enough for us to scan

2.After receiving the photo of the mainboard,  we will ask the XM Manufacturer for a firmware, and upgrade the NVR with the new firmware.    

Upgrade steps

Attached upgrade firmware is for your reference, please download and unzip it first.

1. Copy these 2 files to your USB flash drive, the root directory(Do not under any folder, see the picture attached)

2. Power off the DVR and insert the USB device

3. Power on the DVR, it will upgrade automatically. Please give it a try and let us know the outcome.

My UI Interface shows “No signal” or “Black Screen”

We need to divert this issue into two situations:

1. DVR Indicator light is on:

(1) Cause: The camera system’s video output resolution is 1080P. If your TV monitor resolution is below 1080P, this issue will occur. Steps:

Please right-click and hold your mouse for over 10 seconds to see if the system can reboot or not. Or, please try to connect the system to another TV monitor with a higher resolution (above 1080P)

  (2) Cause: The hard disk drive inside of the DVR box is broken, and use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is having the issue, and needs a replacement, plz contact email for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

After the steps, if the thing still can’t be resolved, which means the DVR box is broken, plz contact email for a replacement DVR box if their warranty is still 1 year, and if the warranty is over 1 year, plz leave us a five-star review for us to apply for a free DVR box

.

2.DVR Indicator light is off:

(1) Cause: The power adapter 12V 2A connected to DVR box is broken

Step: Use another power supply 12v 2A to power on the DVR unit to have a try

( If you do not have a spare one, use the one that is connected to 4 cameras to have a try)

(2) Cause: The hard disk drive inside of the DVR box is broken Step: Use the screwdriver to open the DVR box to unplug the wires of the hard disk drive, and reboot the DVR to have a try. If the DVR box can be rebooted after unplugging the wires of the hard disk drive(HDD), which means the HDD is broken, and needs a HDD replacement, plz contact email for a replacement HDD if their warranty is still 1 year, and if the warranty is over 1 year, plz leave a five-star review for us to apply for a free HDD  

.

After the steps, if the thing still can’t be resolved, which means the DVR box is broken, plz contact email for a replacement DVR box if their warranty is still 1 year, and if the warranty is over 1 year, plz leave us a five-star review for us to apply for a free DVR box

How to Share the APP to other

1.Open the “Xmeye Pro ” app ,Click the pencil to edit,

Then Click the Share

.

2.Select the function which you want to share

.

3.Finally enter the user name who you want to share ,then you can shre to others successful.

How to reset XMEye Pro Password?

1. Click on “Forget Password”

2. Input your number or Select “Email”(Depends on the method you signed up before)

3. Input your email address and click on “Get Code”

4. A code will be sent to your email, input the verification code here and click on “Next” to continue.

How to Flip the Camera

1. select the channel of the flip camera

2. Navigate to “Main Meun“–> “XVI control“

3. check the”Overturn

How to find out the “Cloud ID” (Serial Number) when adding device to PC Client “VMS”?

The “Cloud ID” is “serial Number”on the NVR UI Monitor Interface

Go to your TV Monitor that is connected to NVR, Navigate to “Main Menu–>Advanced–>Version“–> You will see the Serial Number

Why the DVR can’t record or playback video

If HDD(Hard disk drive) is having issue or something wrong with record setting, the DVR can’t record/playback the video

1. Check if the hard drive status is normal or error

Navigate to: Main Menu–>Advanced–>HDD info. 

 If it’s hows “error” or no hard drive info, means hard drive failure. (need to replace hard dirve)

2. Check the record plan is set up for 24/7 continues recording

Navigate to Main Menu–>Record Conf

Channel : select “All”

Period: “00:00-24:00”

Select “Regular”

3.   Please make sure the HDD was set up to “Overwrite”

Navigate to Main Menu–>General–>Storage Full

Any ideas, let us know. Thank you for your cooperation. 

.

You now need to configure the NVR so that it’s ready to connect to your network. Don’t worry – this is simpler than it sounds. This initial setup is simplest when done on the local GUI, using a directly connected monitor. The following steps walk you through this initial setup process:

Note – Avoid plugging anything into the back of the NVR until instructed to do so in this tutorial.

Firstly, you’ll need to look at the back of your NVR and make sure you can identify the following parts that are needed for this stage:

[1] – PoE (Power over Ethernet) ports (Most Hikvision NVRs have PoE ports which will power any camera via the network cable. Those that do not will require you to connect the camera across remotely, using a separate PoE injector or switch for power.)
​

[2] – VGA display port
​

[3] – HDMI display port
​

[4] – USB port(s) (and mouse – one should come included with the NVR)
​

[5] – LAN port (and ethernet cable – Cat5e or Cat6 is fine)
​

[6] – Kettle power socket (the power lead is included with the NVR)​

Now, follow these steps. It is easier if you leave your cameras disconnected until prompted later in this guide:

Step 1:

Plug the kettle plug into the power inlet to connect the NVR to a power supply.​

​

​

​How To basic setup of Hikvision NVR

Read More :

• CCTV Super Password Tools
• Configuration Guidance of AcuSense NVR
• CP PLUS XVR complete setup guide

Step 2:

Connect your NVR to a display (this can be any monitor or television) by connecting either an HDMI or VGA cable from the monitor to the corresponding port in the back of the NVR.​

​

​

Step 3:

Plug your USB mouse into one of the NVR’s USB ports.​

​

​

Step 4:

Use an ethernet cable to connect your NVR to your local network – Plug one end of the cable into the RJ45 ports into a network access point (such as an ethernet port on your router), and the other into the LAN port in the back of your NVR.​

​

​

​

Step 5:

Turn the NVR on and let it boot up. Ignore the beeping noise, it’s completely normal and just the NVR telling you that it isn’t properly configured yet.​

​

You may get a prompt to adjust the NVR’s resolution to match the connected display, click “yes” to view everything in the best resolution supported by your display.​

​

​

​

Step 6:

​

Set your language when prompted.​

​

​

​

Step 7:

Set a password for the NVR , as well as a “Channel Default Password”, which will be passed onto any inactive device that is directly connected to the NVR’s PoE ports. We recommend keeping these passwords the same for simplicity’s sake. It’s key that you set a password that the NVR defines as strong and that you remember this password, as resetting the passwords on Hikvision devices can be a hassle that you want to avoid, if possible.​

​

Note – If you have lost your password then please see our guide on How to Reset the Password of your Hikvision Camera/NVR in 5 steps using the SADP Tool​

​

​

​

Step 8:

Now set a valid “reserved email” address for the NVR, which Hikvision will use for verification if you need to reset your password.​

​

Step 9:

Next, set an unlock pattern of your choice by using your mouse to draw any shape you like – you will be asked to do this twice to confirm the pattern. This will be used to quickly login to your NVR in the local GUI.​

​

​

Step 10:

Now, set your time zone, your preferred date format, and date/time.​

​

​

Step 11:

​

On the Network Setup page:​

​

Leave the “NIC Type” as it is.​

​

Either leave the “Enable Obtain DNS Server” box ticked, or untick it and use one these recommended public DNS servers.​

​

It is best to leave the “Enable DHCP” box unticked here. Instead, set the “IPv4 Address” of the NVR to an unused IP address on your network, which is within your gateway’s range. Your Gateway will typically be the IP address of your router. E.g. if your router’s IP address is “192.168.1.1”, you’ll want to give the NVR an IP address within the range of “192.168.1.x”, where “x” is any unused address between “2” and “254”.​

​

Note – DHCP can be left on during this stage of the setup to automatically assign your NVR an open IP address if you like, just be sure to turn it off again once your system up and running. To disable it again once set up, just go to: ​

System/Configuration→ Network → TCP/IP → DHCP Off → Apply​

​

Input the Subnet Mask of your network (typically it’s “255.255.255.0”) and “IPv4 Default Gateway”. If you’re unsure of these, see the below articles which explain how to check what they are and if a particular IP address is available:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

The “Internal NIC IPv4 Address” can be left as it is, this just refers to the NVR’s own LAN address (so Plug and Play cameras will use IP addresses on this range).​

​

​

​

Step 12:

You can now stop the annoying bleeping! Select your hard drive(s) from the list and click “Init” to format it, and then “Next” when the formatting has completed.​

​

Note – This will completely wipe the drive, so please make sure that any that are being reused to not have data that you might need on them. ​

​

Step 13:

​

The next page is for the Camera Setup. As mentioned earlier, we recommend connecting any cameras after the NVR setup process has completed, so you can skip this page.​

​

Note – Please see part 4 for the instructions for adding cameras to your NVR after the initial setup. ​

​

Step 14:

You will now be taken to the platform access page. Again, skip through and leave this for now.​

Note – Please see part 12 for adding the NVR to the Hik-Connect app, which revisits this page. ​

​

​

Step 15:

Finally, you’ll be taken to the Change Password page and given the option to set a new admin password. Ignore this, unless you actually want to change your password. Remember, your admin password is different from your activation password, which you’ll need to use when activating individual cameras on your network.​

​

Click “Exit” and “Yes” on the “Exit Wizard” popup.​

​

​

That’s the initial setup of your NVR complete. You should now be taken to the NVR’s live view page (you won’t see your cameras until these are connected in Part 4), with your main navigation menu at the top of the screen.​

​

How to Access Device from Web 2M DVRs

When devices are connected to the network, they can also be accessible from a computer. The first thing you need to make sure of is that the computer you are using and the DVR/NVR are connected to the same network (network is coming from the same router for both devices). You will first need to obtain the IP address of the DVR/NVR from Menu → System → Network → IPv4 address.

After noting the IP address of your device, open Internet Explorer and in the address search bar type in the DVR/NVR IP address. If the NVR and the computer are on the same network then it will pull up the login page of the DVR/NVR. The credentials will be the same as when you log into the local interface of your device.

Read Next :

1. Resetting your UNV NVR Password 3 Ways
2. Lorex Fusion Setup Guide
3. Hikvision AX PRO Configuration Full Setup – Video

How to Find the Serial Number Using 2M Tool

Click here to download 2M Tool

2M Tool is used to find the IP address of your 2M NVR, DVR, or IP camera, as well as limited management of its settings. You only need to make sure that the computer you are using 2M Tool on is connected to the same network as the device that you are trying to search for.

Why do we need the serial number? The serial number is mainly used in case of a customer needing a password reset on their device.

How do we find the serial number? There are a few ways to find the number:

• sticker on the device
• sticker on the box that the device came in
• web page client of the device
• using 2M Tool

In the case that you forget the password for you device in which you will not be able to access the web page, and the camera is too high up to reach to find the sticker, you can use 2M Tool to find the serial number. 2M Tool does not automatically show the number; you must force it to show. First, you will need to click on the Settings icon to show the options:

Then another window will open where you can select Serial Number to show.

Once you hit OK, the serial number will then appear.

How to Install Plugin for Internet Explorer

This article features screenshots from our 2MN-8XXX series NVR and our 2MT-4XXX series DVR, but the same principle will apply to any other recorder. This is because each recorder requires a plugin in order to view the cameras on the web page. You will have to manually install the plugin, but it is usually always provided as a link for easy access.

First, you must make sure that you are using Internet Explorer. Internet Explorer is the only browser that can support these plugins. It is possible for some devices to be viewed on Google Chrome or even Firefox, but then other functions are very limited so it is highly not recommended to use those browsers. Once Internet Explorer is open, and you navigate to the device’s web page by entering the IP address, there should be a link shown on the page. You can see on the picture below that the link is located on the top of the page.

When you click on the link, a pop-up will appear on the bottom of the page that will let you choose whether to Run the program or Save the program onto your computer. Note: Running the program will not save it. If you wish to save the program, please select Save. Once it has finished downloading, then you can run the program from the file location.

If you choose to Run the program, an error message will appear noting that the publisher couldn’t be verified. This is no issue; the plugin will not cause any harm to your computer. Hit Run, and run the installation. Some installations will require you to close out of Internet Explorer in order to complete the setup.

Once the setup is complete, refresh the page, and another message will pop-up on the bottom that asks you to Allow the add-on to run. Select Allow, and log into the page. Now you should be able to view your cameras on the web page.

How to Set Up 2M Guard

2M Guard is the phone app that we use for our NVR’s to view cameras from our phones offsite.

This app only works for models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

1. Find the Register Code and/or QR Code for your DVR/NVR

• on NVR menu: Menu → System → Network → P2P OR Menu → Network → P2P
• on web menu: Setup → Network → P2P

2. Two ways to add a device onto the app:

1. Star4Live
2. directly on the app

Method 1: Adding Device Through Star4Live

• Go to https://www.star4live.com/login
• Click on Login if you already have an existing account or Sign Up if you do not

• Once you have logged in, click on Add and another window will pop up prompting for a Device Name and Register Code. Once all of the required information has been filled out, hit OK and your device should show up under My Cloud Devices.

• Once you have successfully added the device on Star4Live, open the app and log into your account using the same credentials that you created/used on star4live.com
• Go to Live View and tap the icon in the upper right corner to select a device
• Select the device you would like to view
• Start live view

Method 2: Adding Device Directly on the App

• When you first download the app it will prompt you to either Sign Up or Login
• Tap on Login if you already have an existing account or Sign Up if you do not

• Open up the app menu and go to Devices. This section shows all of the devices that have been added onto your account. To add another one, tap on Add at the top of the screen.

• You can choose to add the device by scanning the QR code or by manually inputting the Register Code. To move forward with either of these options, you will need to tap on Scan

• A screen will appear for you to scan a QR code. If you choose to scan this is where you will do it, but if you choose to manually enter the Register Code, tap on the edit icon on the bottom.

• Once all of the correct information has been filled out, hit the Save icon in the upper right corner.
• In order to see the cameras, open the app menu and tap on Live View
• At first, it will look blank. This is because we need to add the cameras to the windows. Tap on the Add icon in the upper right corner

• A list of your devices will appear. Select the one that you want to view and hit Start Live View on the bottom

• Now you can view your cameras on the go!

How to Set Up 2M Station

When first running the program, it will prompt you for a username and password which will be admin/123456 by default. It is recommended that you change the password after installation.

Once you are logged in it will show the menu. Click on Device Management to add any devices. On the left side make sure that Encoding Device is selected. It will show at the bottom of the screen any devices that are online as long as the computer is on the same network as the devices.

There are two methods to add an online device. The first method is fairly simple. All you need to do is check the box for the NVR that shows under Online Device and then click Add. The second method to adding an online device is to manually add it. First click on Add next to Managed Device, and it will open another window where you can input the details of your device. It will ask for:

• Device Name → can be any name for your device
• IP/Domain → local or public IP address of NVR
• Port → port number of NVR
• Username → username of NVR
• Password → password of NVR

After putting in all of the correct information of your device, click on Add and then the device should come online.

Another method to add a device is by using the P2P method which allows for a user to view their cameras offsite from any location. The device will be added as a Cloud Device instead of an Encoding Device.

It will show Login and Register buttons that will link to your Star4Live account which will show the devices you have previously added. After logging in, it will take a minute or two for the devices to show online. At first, it will say Offline (Connecting…), but eventually the status will show Online.

After successfully adding all of your devices, go back to the menu and click on Live View to view your cameras. A list of online devices will show on the left side of the window. Click and drag the device into the window view in order to load all of the video. If not all of the cameras are wanted in view, you can click on the plus sign next to your device and it will show a list of cameras connected to the NVR. You can click and drag specific cameras onto the live view screen.

How to Set Up Email Notifications Using Gmail

Gmail will have automatic security settings that need to be disabled before configuring email settings in the NVR. You will need a computer in order to edit these settings. First, log on to your Gmail account and then click on the square icon in the upper right corner of the page. Click on Account.

Security → Scroll to the bottom until you find “Less secure app access” → “Allow less secure apps: ON”

Now that Gmail has been set to allow app access, we can move on to the NVR settings. These can either be configured through the web page or through the NVR itself.

Through the DVR/NVR: Main Menu → Network → Basic → Email

Through the webpage: Setup → Network → Email

• Server Authentication: On
• Username: email that you will be sending from (can be a throwaway email)
• Password: password of email account
• SMTP server: smtp.gmail.com
• SMTP port: 465
• Enable TLS/SSL
• Can choose to attach image or not
• Sender: sender name
• Sender’s address: email address (same as username)
• Recipient: any recipient name
• Recipient address: email address of recipient
• Test email

After you finish entering all of the settings and the test is successful go to Camera → Motion → Select Camera → Trigger Actions → Send Email

How to Share a Device

Each NVR can only be added by one account at a time, so if one wants to add a device onto multiple accounts they would need to share the device with one account being the “main” account. This means that one person will have the device added to their account and that person will share the device with other people. Each person still must have their own Star4Live account.

How to share the device is simple. First, you will need to log onto the main Star4Live account which the NVR has been added to. It can be done either through the computer or your personal phone.

Sharing from Computer: after logging into the account your list of added devices will appear. Click Share on the row for the device you are wanting to share.

Then a menu will appear to enter the account you want to share to, the Valid Till date, User Rights, and any Description you want to give.

• Share To → can either be the username or the email of the Star4Live account you are sharing to
• Valid Until → can go up to X amount of years, months, or just a few days
• Permission → can choose any user rights that have already been configured on the NVR (admin, etc.)
• Remarks → can give a short description to the recipient about the device that is being shared

Once all of the information has been correctly filled out, click Confirm to successfully share.

Sharing from 2M Guard Phone App: after logging into your Star4Live account on the 2M Guard app, go to your Devices and then tap on the device that you want to share. A small menu will appear. Then tap Share on the bottom of the screen.

The next window will show the device and a list of the cameras that are connected and online. You can choose specific cameras, or select the device so that the entirety of its cameras are selected for sharing.

Once your device(s) has been selected, the Share menu will finally appear. The app will ask for the same information as the computer does, but it will not give a space to fill out a description. Fill out the Share To and the Valid Period the same as you would do on the desktop instructions written above. The only other difference between the Star4Live browser and the app is the sharing Type: you will be able to choose between Role or Function.

• Role: can choose a specific user or role to share to another user
• Function: can choose specific functions to share to another user with Live View being automatically selected by default

NOTE: Only admin rights will allow another user to access the device through the web browser or through 2M Station because they both allow a user to make changes to the device. If you do not wish for another user to be able to make any kind of changes (viewing only), please choose the By Function type.

Once one of these methods have been completed to share the device, the recipient only needs to log into their Star4Live account and the shared NVR should show automatically under their own device list.

How to Sign Up for Star4Live Account

Star4Live is the server that we use to view NVR and camera footage over the web. Each customer needs to have an account to view and manage their devices.

This is only valid for models: 2MT-4004, 2MT-2008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

• Go on https://www.star4live.com/login
• Click on Sign Up

• Clicking on this link will direct you to a new page that will prompt you to fill out information in order to create an account
  1. Username
  2. Email → Acquire: will send a code to the email entered
  3. Verification Code: code that was sent to email. NOTE: If you have not received anything in your inbox, please also check the Spam folder.
  4. Password
  5. Confirm Password
  6. Service Agreement

• Once all the information has been correctly filled out, click Register and your account will be ready to use.

How to Upgrade the Firmware

Every now and again, we will release a new firmware update that can either hold new features for your unit, bug fixes, or a bit of both. We have made it simple to request the newest firmware so that there is no need to wait for a file to be sent. First, you will need to make sure that your device is connected to the internet so that the NVR will be able to communicate with our servers.

Method 1: From the NVR Interface

Then you will go into the Main Menu and click on Maintain. There will be a section for Upgrade.

There are two options for upgrading:

1. Local Upgrade: this option is only good if you already have the firmware file loaded onto either a USB to plug directly into the device or if you already have the firmware file in a location on the computer which you are using to upgrade the device
2. Cloud Upgrade: this option is good if you do not already have the file on hand. It will automatically read the current version and detect if there is a newer version available

You will most likely want to choose the Cloud Upgrade option unless you have received the firmware file from Tech Support beforehand. Click Cloud Upgrade, and wait for the device to finish its search. It will either notify you that the current version is already the latest, or it will show a newer version, and the Upgrade button will highlight at the bottom of the screen.

The upgrade time will vary between 1-5 minutes, sometimes lasting longer depending on the size of the update. Once the update has finished, the device will automatically restart. It will be ready to use again once it has fully finished the reboot.

Note: Please make sure that the device does not disconnect from the network or from power because it can cause a risk in damaging the unit if there is a failed update.

Method 2: From the Web Interface

The NVR can be updated from its web page if there is no monitor connected to the unit, or if it cannot be physically accessed. From the web page, you will navigate to Setup → Maintenance → Maintenance → Cloud Upgrade → Detect or Check for Update. The process is the same as it is from the unit itself, and the same rules will apply.

How to Use Star4Live

Star4Live is the server that we use to view NVR and camera footage over the web. Each customer needs to have an account to view and manage their devices. You must use Internet Explorer in order to access all of the functions of Star4Live.

This is only valid for models: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16 and our IP cameras.

• Using Internet Explorer, please go to https://www.star4live.com/login
• Login if you already have an existing account or Sign Up if you do not
• If you are using this site for the first time on a device, please make sure to install the P2P plugin. The website will show you a prompt at the top of the screen. Make sure to allow pop-ups on your browser because clicking on the link will open up a new window

• When you log into Star4Live, the first page that shows is the Device Management tab which will show My Cloud Devices. Here is where you can see the devices that have been added to your account, or any devices that have been shared with you under Devices Shared To Me

• In order to access a device’s web page, click on the Access icon

• If the P2P plugin has been installed, the NVR web page will display automatically when you access your device. If not, you will get an error that your device “Cannot be reached.”
• Once the web page has finished loading up, you will need to install another plugin to view the cameras’ live feed.
• After it has been installed there will be a pop-up on the bottom of the screen that will ask permission to allow the plugin to run. You will need to allow this.

What software do I use to view my cameras on my PC, and where can I download the software?

2M Station: 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16

Windows Download Link
MAC Download Link