Swann Camera Troubleshooting

Let’s discuss Swann camera troubleshooting. Like any other brand of Wi-Fi or IP camera for consumer-grade surveillance, you will come across common errors that you can solve easily in a DIY fashion. Refer to this guide for more details.

The Swann brand claims itself to be security made smarter. It backs up its claim by making some of the world’s best value security system. They’re able to compete against the likes of Ring, Nest, Arlo, Bink, and Wyze by providing the smartest of features and the most intuitive of controls.

Regardless, in case your Swann camera stops working, isn’t recording, isn’t connecting to Wi-Fi, or has issues with playback, “ Swann camera Troubleshooting – Problems and Solutions with Swann security cameras” got your back.

Swann camera not working: How to Fix

If your Swann camera isn’t turning on, check the wiring or battery. If it’s offline or has hampered function, disconnect the cameras, disconnect the power supply, and then restart to see if that fixes the problem. Your camera can also stop working if it’s overheated. Cool it down and try again later.

If worse comes to worst, your Swann camera might be “bricked” or rendered completely broken and non-functioning. If it’s still in warranty, you can get it replaced for free or at least get a discount for a replacement.

See More :

• Swann device Password Reset for all model
• How to Install SwannView Link
• SWANN LATEST FIRMWARE UPDATES

Swann camera not recording: How to Fix

If your Swann cam is not recording, it might be because recording is disabled. Go to “Main Menu” the select record. Fix “Record Setup” and “Motion Setup”. You can also set up the “Record Schedule” too.

Check “Motion Setup” to see if that’s the reason why your camera isn’t recording (it only records when it detects motion).

You can also connect one camera only to your DVR or NVR to see if that fixes the recording issues. You can setup an isolation test, cross-check the camera and cable, and interpret the results to narrow down the issue.

Swann camera not connecting: How to Fix

Check your router and make sure the Wi-Fi password entered is correct. Sometimes, your Swann camera might unsuccessfully establish connection with your router simply because you misread a character or capitalized the wrong letter (it’s case-sensitive).

The cam could also be out of coverage area of the router. Make sure the router and the camera(s) are close to one another to ensure a smooth connection.

If the camera is still have issues with Wi-Fi connection, reset or power-cycle your router and try again. It might be an ISP problem. If you believe the camera is in error, you can reset it back to factory settings using the recommendation outlined below.

Swann playback not working: How to Fix

To playback a video, tap the “Playback” icon, then the “Camera” icon, and then set a start and end date and time. You can also search recordings on the recorder below the calendar then tap “Start Playback”.

Sometimes, when you attempt to playback videos, you get blue lines to show it was recorded but get an “open failed” error message when you attempt to play it. This could be caused by bad configurations, lack of storage space, corrupted video files, and failing DVR components.

This could also root from the latest software update. It mostly affects iPhone users but even Android users are affected. Contact a Swann technician or consider replacement if the problem consists.

Swann camera black screen: How to Fix

Some Swann cam users experience CCTV cam black screen or a blank video at night. This might mean the camera lacks infrared night vision, especially if it continues to record and works fine during the daytime or if you put a lamp or light source where it’s supposed to record things.

Maybe you simply forgot to turn the IR on. Fix this by checking camera settings and enabling the infrared light. If that’s not the case, then the infrared night vision camera might lack an IR cut filter.

It could also have a faulty IR sensor. Either way, you might need to have the device fixed by a technician or replaced altogether depending on the severity of the damage or the state of its warranty.

Off-warranty products might require some repair and finagling from third-party repairmen but this means it’s now outside the jurisdiction of Swann.

How to reset Swann camera?

To reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, here’s how to go about it. Locate the reset button. You might need to use a reset key or a pin in order to press it for 10 seconds to start the reset process.

Disconnect the camera from the NVR first before resetting it. You’ll also need to remove it from the PoE switch or power adapter to turn it off completely. Some devices require a pin or cable key to access the small reset button.

FAQs – Frequently Asked Questions

Here are the most frequently asked questions in regards to the Swann cam.

Where is reset button on Swann camera?

On most Swann cams, the reset button is found on the bottom of the device. However, this might vary depending on the model. This button typically requires a needle or pin to push until you hear a click sound. You need to hold the button for 10 seconds to reset the device.

How to find Swann IP camera default password?

The default all-access admin password for Swann is “12345” on the username “admin”. To reset the password for cameras, NVRs, or DVRs, you might need to get the MAC address by downloading some sort of app.

Alternatively, you can reset the camera to default settings by pushing the pin-sized reset button for 10 seconds in order to get the default password back.

Swann DVR default password: How do I find my Swann DVR password?

If “12345” is not the password being used by NVR’s “admin” account and you’ve forgotten what the password is, reset it by downloading and installing the HomeSafe Config Tool first. Open the app, click on your device’s IP address, and note the MAC address.

Now, you can go to the login screen of the DVR, click on “Forgot Password”, and enter the MAC address provided to you by HomeSafe. Click “OK” when you’re done then set a new password.

Why have my Swann cameras stopped working?

You should check first that your camera power supply (or supplies) are properly connected to a wall socket or power strip. If you do have the power supply connected to a power strip, try a wall socket just in case the power strip is faulty or is a specialised unit that doesn’t have all the sockets active at all times.

How do I reset my Swann camera?

Disconnect the camera from the NVR (or from a PoE switch or a power adapter) to turn it off completely. Press and hold the reset button. While holding down the reset button, plug the camera back to the NVR (or to the PoE switch or a power adapter) and continue holding down the reset for 30 seconds, then release.

Why is my security camera black screen?

Some users experience CCTV camera black screen or video going black at night, it’s likely that the camera lacks infrared night vision, or the IR night vision camera doesn’t have an IR cut filter or a faulty IR sensor, or you simply forget to turn the IR on. Quick Fixes: Check camera settings to make sure the IR is on.

How do I get my Swann cameras back online?

All you need to do to get back online is to re-register the camera. Follow the steps below:First, go into the home interface (this is the screen it goes to when you start the app) and tap the “Camera” button on the bottom. On the next screen, tap the camera where it says “Camera is Offline”.

How long do Swann security cameras last?

Unfortunately, details aren’t provided for how long the Lithium Ion battery will last on a single charge, but it’s likely to be around 8-10 weeks based on our use. Obviously, if it’s not practical to take the device down every couple of months, then it may be worth investing in the solar panel accessory as well.

Why is the blue light flashing on my Swann DVR?

The first time you power up your camera, the camera LED will be blinking blue to indicate pairing mode.

Why does my security camera keep going offline?

Security cameras go offline for three main reasons: power outages, loss of internet, or failure of the camera’s components (broken parts or wires). Knowing some quick troubleshooting tips will help you get your camera back up and running in no-time.

What happens if you unplug a security camera?

When your house, the cameras won’t record. When you are away from the home, the cameras record. They’ll still be “working” but not recording.

What to do if all cameras display no image on the DVR monitor?

Is this an existing camera that was working and at some point had video loss? Follow these troubleshooting steps.

1. Test Your Power Supply.
2. Check Power Supply Box Fuses.
3. Test Camera on a Different DVR Port.
4. Use a Test Monitor.
5. Use a Test Cable and Spare Power Supply.

Why is my Swann security camera not connecting?

Make sure that the connection is successful by checking your router and ensuring that your Wi-Fi password is correct. If the camera is still having issues connecting to Wi-Fi, reset the router and try again once it’s back up.

Why does my EUFY camera keep going offline?

Your Eufy camera goes offline if the battery has run out of charge, has lost connection to the HomeBase and Wi-Fi, or you need to update your Eufy app. You should check your battery and check the Wi-Fi settings to ensure that they are working correctly or reboot your camera to solve the problem.

Is Swann a Chinese company?

Swann has always been a leader. From humble beginnings in Melbourne, Australia the business now has offices in the USA, Canada, Australia, UK, Hong Kong and China and a presence in over 40 countries on 6 continents.

Can Swann cameras be hacked?

A popular wireless security camera designed to safeguard businesses and homes was vulnerable to a spying hack. The flaw meant it was possible to hijack video and audio streamed from other people’s properties by making a minor tweak to Swann Security’s app.

Are Swann 4k cameras any good?

The quality of the cameras are excellent. They feel, look and operate great. Simple setup and easy to use.

What does the blue light on my DVR mean?

The blue light indicates that the DVR (or other receiver) is outputting an HD signal. It could be the HDMI negotiation with your new TV causes it to stay on when the TV is off. If it’s too bright for you, a small piece of opaque tape is recommended.

What does it mean when Blink camera flashes red?

The Blink Video Doorbell flashes a red LED on the ring surrounding the doorbell button when it is seeking connection. During setup, and change of system or Wi-Fi, the red LED shows if the doorbell is ready to connect. If the red LED is not flashing as expected, remove one battery for five seconds and replace it.

What does a blue light mean on a camera?

LED setup reference guide

A flashing blue light on a security camera means you are ready for the WiFi protected setup.

Why do my wireless cameras keep disconnecting?

There are two main reasons that a camera may lose WiFi connection. It may be installed too far from your WiFi router, or it may not have sufficient bandwidth on your WiFi. Please contact our customer support for help in diagnosing this issue and confirming the cause.

Why won’t my security camera connect to my Wi-Fi?

Hold your phone in the location of your camera and check the number of dashed Wi-Fi coverage on your phone. If the connection is poor, if possible, reduce the distance between the camera and your Wi-Fi router. Consider a wired installation or consult your internet provider for solutions.

Why does my IP camera lost connection?

Network Conditions

Surveillance Station may lose connection to your camera when the Internet connection is poor or if changes are made to bandwidth, firewall, or IP address settings.

How do I disable Swann camera?

How do I disable Swann camera?

1. Yea, it’s possible to turn off the INTCAM manually.
2. Try this procedure, using the button on the back of the cam –
3. Press and hold the Pair button for 30 seconds.
4. To turn it back on, just press the Pair button for a second, Don’t hold too long or it’ll go into pairing mode.

Will DVR still record if unplugged?

The Cloud will continue to record your set programs while the physical DVR is unplugged. You are also correct that if your additional TV boxes are unplugged, this will not affect your planned recordings.

How do I stop my security camera from being unplugged?

Indoor cameras

1. Run your camera’s power cable behind furniture or shelving so that it’s harder to spot and unplug.
2. Install cable clips to help keep the power cord attached to the wall. Check your local hardware store for availability.

How do you troubleshoot a security camera?

How do you troubleshoot a security camera?

1. Know your login details.
2. Check the power source (most cameras are PoE)
3. Check to see if cameras work from inside or outside the network.
4. Check the cabling.
5. Reboot the system.
6. Check for IP conflict.
7. Check ARP tables.
8. Update software & firmware.

Conclusion

Even though Swann isn’t as well-known as Ring, Arlo, or Nest, it has a significant share of the Wi-Fi cam market because it caters to a significant niche. Many people are curious how to troubleshoot this camera because they’re loyal Swann customers.

There’s great demand to know how to make sure their Swann devices work and operate smoothly. They also wish to know whether their Swann is broken or fixable in some DIY way.

How to Connect Swann Camera?

If you wish to learn how to connect your Swann cam to Wi-Fi, to your phone, to your TV, to your laptop, to your MacBook, to Alexa, to the Internet, and so forth, you’ve come to the correct guide.

People are curious about the Swann camera because it provides a dependable and affordable alternative to your Ring cams, Arlo cams, and Nest cams. It does everything those cams could do in terms of Wi-Fi-based and app-based operation but in a format much closer to CCTVs.

It’s this dependability that Swann got a loyal consumer base who’d read articles like this about “How to connect Swann camera?” and whatnot. So let’s discuss how to connect the smart cam to different devices already!

How to connect the Swann camera to Wi-Fi?

In order to connect your Swann Wi-Fi or IP cam to Wi-Fi, you need to pair it up with your Swan Security app.

• Go to the Menu: To do so, tap the menu on the upper-left corner of the screen, then select “Pair Device”. Afterwards, tap “Start”.
• Scan QR Code: Attached to your camera is a QR code sticker. Have your smartphone scan that. If you don’t have the QR code, tap “Manual Pair” and get the MAC address above the serial number of your cam.
• Enter Wi-Fi Password: Now you can enter the Wi-Fi password and tap “Next”. Enter a camera name then tap “Next”. Set the camera into “Pairing Mode” by pressing and holding the rest or pair button until the LED blinks blue. Now tap “Next”. Then tap “Start”.
• Congratulations Message: If your cam successfully connected to Wi-Fi, you’ll see an overview on the app. After that’s done, tap “Next”. You’ll get a “Congratulations!” message once setup is complete.

How to connect Swann security cameras to Phones? (iPhone, iPad, Android)

Remember the section above, where you had to download an app and scan a QR code via the app in order to pair up your camera with your phone (whether it’s an Android, iPad, or iPhone)? That’s how you connect your mobile device to your Swann cam.

Get SAFE by Swann for Android devices, SwannView Plus for iOS devices, and SwannCloud for iPad and Android tablets. Swann Security App and SwannView Link can be used for multiple devices.

Finally, download HomeSafe View for desktop PCs doing NVR/DVR remote viewing and AlwaysSafe for NVW-485, NVW-490 & SWWHD-PTCAM Cameras.

See more:

How to connect the Swann camera to the TV?

You can hook up your Swann cam to your TV using the Digital Video Recorder (DVR). It has a hard disk of your recorded footage that a modern smart TV or flatscreen TV with an HDMI connection should be able to read and review videos with.

You can also connect Swann cam to your FireTV by first connecting the Swann cam to Alexa (more on this below).

How to connect Swann camera to Laptop, Macbook?

Download the HomeSafe View for desktop PCs in order to connect your Swann Camera to your MacBook or Laptop. To view Swann cam on your Windows PC, launch the Device Configuration Tool and have it detect the camera and NVR (Network Video Recorder).

Any cameras directly connected to the NVR won’t be shown. The cam’s IP address should be visible here.  Click on it like a link to launch Internet Explorer and view it from there.

How to connect the Swann camera to Alexa?

Open the Amazon Alex app. Click the three lines icon on the upper-left corner of the screen. Select “Skills and Games” tab. Search for the “Swann Skill”. Select the skill then login to your Swann account.  Press “Done” and then select “Discover Devices”.

The new Alexa Skill should then detect your Swann cams and have them listed on the “Devices” tab. Amazon Alexa works with Swann cameras to stream live camera video to your Echo Spot, Echo Show, or 4K Fire TV.

See more here:

How to connect Swann DVR to the Internet?

In order to connect your Swann DVR to the Internet, you need to first connect the DVR with your phone or tablet care of SwannLink. From there, it should have the ability to link to the Internet by proxy.

SwannLink connects systems care of peer-to-peer technology. Just scan your ID number or QR code to SwannLink in order for it to directly connect your smart devices to your DVR via the cloud, with the Swann DVR verifying the ID of your smart device as well as the username and password of the Wi-Fi.

FAQs – Frequently Asked Questions

Here is the most frequently asked questions section of this guide.

Why is my Swann camera not connecting?

Your ISP or router might have a bad Internet connection. Reset or power-cycle the router to get it back online. If the issue persists, contact your ISP for more details. Or maybe your cam is out of the router’s coverage area. Make sure they’re both near one another for best results.

Finally, check the Wi-Fi password. Make sure this case-sensitive password has been entered correctly when prompted by your app.

How do I get my Swann cameras back online?

Enter the Wi-Fi password again and make sure it’s correctly entered since it’s case-sensitive. Put your cam nearer the router. Reset the router and make sure your ISP is providing you with a solid Internet connection.

If the camera itself is failing to connect to a perfectly fine Wi-Fi, you might need to troubleshoot the cam, its connection to the app, its connection to the NVR or DVR, and so forth. You might need to reset it to factory settings altogether.

How do you reset a Swann security camera?

To reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, locate the small reset button (usually found on the underside of the device) and press it with a reset key, needle, or pin for about 10 seconds. Before doing a reset, disconnect the camera from the NVR and PoE switch.

See more: https://support.swann.com/s/article/tAM37IZ5qr

What app do I use for Swann security cameras?

The Swann Security App manages all of your Swann cameras in one central hub. The HomeSafe View app for the PC or Mac is the desktop program for remote viewing of NVRs and DVRs.

AlwaysSafe is the app for NVW-485, NVW-490 & SWWHD-PTCAM Cameras. You can also download SAFE by Swann for Android devices, SwannView Plus for iOS devices, SwannView Link for multiple devices, and SwannCloud for iPad and Android tablets.

How to access Swann DVR from the computer?

To view Swann on PC, You can see this post: https://securitycamcenter.com/view-swann-cameras-homesafe-view-software/

Conclusion

Hopefully, this guide has shown you everything you need to know about Swann cameras when it comes to setting them up, connecting them to different devices, and troubleshooting any errors you might encounter when operating them.

How to Reset Swann Camera?

You’ve reset one camera you’ve reset them all, right? Well, kind of. In the case of the Swann Camera or any other Wi-Fi security camera out there, it’s some variation of finding the reset button, waiting for the light to change, and then you’re done.

The Swann brand claims to produce some of the world’s best value security solutions that also offer the most intuitive controls and the smartest of features. They intend to empower you, the consumer when it comes to their quality products like their Wi-Fi or smart device cameras.

Although they’re not as well-known as Ring, Arlo, or Blink, they have their own market share and niche to cater to. This is why so many people are curious about how to reset the Swann camera. It’s not exactly the same as resetting cameras from Ring and Arlo.

How to Reset Swann Camera

In regards to how to reset Swann Camera models NHD-805/806/810/811/815/815AF/816/817/818/819, here’s the nitty-gritty. There’s an extra cable for the models above that isn’t a connector but a reset button. It looks like a reset key to use on a keyhole or pinhole to prevent accidental resets.

When resetting the Swann Cam to factory settings, you need to disconnect it from the NVR first. Or from its power adapter or PoE switch. This will turn it off completely. Now locate the reset button press and hold it. Some devices might require a cable key or pin to access the button.

Reconnect While Resetting Then Disconnect Afterwards

While holding the button down, plug the camera back to the NVR, PoE switch, or power adapter. Continue holding it down for about 30 seconds before releasing. At this point, disconnect the camera again to turn it off completely.

This should reset your cam to factory settings. Unlike other Wi-Fi camera models, Swann Cams make it more complicated to do a reset to avoid accidental resets, like you accidentally pressing the button or inserting a pin into the reset pinhole when you have no intention to reset to factory settings.

Why Do You Need to Reset the Swann Camera?

Sometimes, the Swann Cam—like any other sophisticated piece of electronics, such as your laptop, smartphone, and tablet—can encounter a glitch or an error that keeps it from properly connecting to your Wi-Fi, using its motion alerts, or uploading its footage to the cloud (if you paid for the service).

You can do a host of things to troubleshoot such errors, including power cycling the device like a wayward router or fixing your router itself to re-establish your Wi-Fi connection if the problem isn’t with the Swann hardware itself.

If push comes to shove and none of those tips work, you can do a hard reset to factory settings (the settings right off of the box or the factory line) to get it working back to normal. You’ll still need to put back your customizations afterwards though.

The History of Swann 101

Swann traces its roots back to Melbourne, Australia. It eventually grew from its humble beginnings, with it now being an international or multinational company with offices in the United Kingdom, the United States of America, Canada, Hong Kong, and Mainland China as well as Australia.

It even has a presence in over 6 continents and 40 countries. What separates Swann from other security companies riding the Wi-Fi cam thread is that it’s a pioneer in the field of Do-It-Yourself (DIY) security with its often imitated features taken from many of its products.

It has doubtlessly done its part in making households and neighborhoods safer compared to before, when the only cameras regular consumers could afford were Nanny Cams and Baby Cams.

Swann’s Membership with the Infinova Group

At present, Swann serves as an Infinova Group member, thus providing major commercial institutions and startup businesses alike with enhanced security device production through better manufacturing abilities, cutting-edge research and development, and state-of-the-art innovations.

They’re at the forefront of networking and security solutions plus they’re not limited to the video doorbell or Wi-Fi security camera market like the Amazon-backed Ring and Blink camera lines. They’ve also expanded their international network access thanks to their Infinova Group backing.

They’re specifically dependable when it comes to making the one-app ecosystem standard work superbly in their models of smart devices, as opposed to others that use multiple apps or one app per camera model.

Swann’s Focus on Crime Prevention

While other companies would rather turn their Wi-Fi camera offerings into Swiss Army Knives of functionality that assist in making the Smart Home future of the 21^st Century a reality, Swann has established its market presence with a different tactic.

They’re more about giving consumers true security, which means they have more of a focus on crime prevention. They provide their cameras with alarms and direct lines to the police for emergencies instead of turning their camera into the next smartphone with non-essential features.

This is also why most Swann cameras offers two-way talk, sirens, alarms, sensor lighting, motion sensors, night vision, and more. This deters not only midnight prowlers and burglars but also package thieves and neighborhood brats.

Swann’s Enforcer Cameras

Swann’s Enforcer Cameras take crime deterrence to another level by using True Detect detection sensors that detect heat, motion, and people. The people detection in particular keeps down power usage and false alarms involving strays and wildlife like cats, chipmunks, birds, and raccoons.

When triggered, True Detect activates the alarms and chimes with all its trimmings. You’ll get mobile alerts, spotlights, flashing lights, video recordings, and more as though you’ve tripped the museum alarms that alert the security guards (or your closest neighbors).

Many of Swann’s more sophisticated inventions include vehicle and pet detection, face recognition, and the peace of mind that your home is protected through cloud and local recordings. This is why it has camera reset included to deal with software errors from all those settings.

Things of Note

We believe that the Swann Camera allows customers to protect and stay connected to their home and/or businesses no matter the circumstances through best-value and intuitive design. This is reflected upon the ease by which you can reset their cameras.

This proves that Swann is one of the global leaders in security monitoring with consumer electronics or smart devices as well as security-centric solutions for smart homes and commercial establishments of the present and the future. What more can you ask for a renowned company with affordable wares?

1. Overview of Product Functions

Describes the main features that users need to know when using the NVR.

Basic Features

• Support for network device access, including network cameras, IP domes and network video servers, as well as third-party network cameras.
• Support for the standard Onvif protocol.
• Each channel supports the preview of primary and secondary code streams.
• Each channel supports adjustable encoding parameters, including resolution, frame rate, code rate, image quality.
• Each channel supports regular functioning and alarming, custom 1, custom 2 and other intelligent video template parameters.
• Support for fast addition of IP channels.

Local Monitoring

• Support for VGA and HDMI displays.
• Support for multi-screen video preview.
• Support for the preview of up to 1/3/4/6/8/9/10/13/16/20A/20B/25/32/36/40/64 screens.
• Support for the preview of shortcut menu operations.
• Support for front-end intelligent analysis.
• Support for video motion detection, video loss detection, video occlusion detection and port alarm detection.
• Support for a variety of mainstream PTZ control protocols, and also setting and recalling of preset position, cruise path and trajectory.

Hard Disk File Management

• Support for hard disk SMART information display.
• Support for bad track detection.
• Support for setting of hard disk property: redundant, read-only, read-write and backup.
• Support for hard disk sleep.
• Support for hard disk pack quota, which can be divided into disk pack or different channels to allocate different video storage space.
• TC-R58(20/40/80) configuration: I/B/N _s TC-R38(40/80) configuration: I/B/N(/Z) and TC-R31680 configuration: E/B/N(/Z) series devices support disk array.

Video Recording and Playback

• The video trigger mode includes: timer and port alarm, motion detection alarm, detection or port alarm, detection and port alarm, video loss alarm, video occlusion alarm, intelligent analysis alarm and other alarm situations.
• Support for pre-recording and delay of linkage videos of all alarm types.
• Support for querying of video files by general conditions/events.
• Support for local redundant recording.
• Support for locking/unlocking of video files.
• Up to 4 video recording periods can be set a day, and the recording trigger mode in different periods can be set independently.
• Support for holiday plans.
• Support for querying of videos by channel number, video type, start and end time and file type.
• Support for several playback modes including regular playback, event playback, label playback, intelligent playback, video summary playback, time-phased playback, picture playback and external file playback.
• Support for video snapshot function. Different types of videos are distinguished with different colors.
• Support for pause, fast forward, slow, forward 30S, reverse 30S, step, step back, stop, one day before, one day after, as well as dragging your mouse for locating.
• Support for rolling your mouse wheel to zoom in and out the playback timeline.
• Support for digital zooming of any area.
• Support for video file playback function.
• Synchronous playback of up to 16 channels is possible for devices with 16 channels and above.

Data Backup

• Support for backup of videos, pictures and other data via USB devices.
• Support for bulk backup by file range and type.
• Support for playback, clipping and backup of videos.
• Support for fast backup by channel and time.
• Support for management and maintenance of backup devices.

Alarm and Abnormality Management

• Support for setting of the arming time of alarm inputs/outputs.
• Support for video loss, motion detection, video occlusion, port, intelligent analysis, detection or port, detection and port and other alarm detections. All the alarms can be linked to single-screen display, text plan, sound alert, email and alarm output, and can trigger the recording of any channel.
• Support for disk full, no disk, disk read/write error, illegal access, IP address conflict, MAC address conflict, no redundant disk available, network disconnection, abnormal hot standby, abnormal array, disk overloaded, abnormal recording, disk SMART abnormality, disk temperature abnormality and other abnormality detections. In addition, the POE equipment also supports the POE overload detection. Various exceptions can trigger screen prompt, sound alert, upload center, email alarm and port alarm.
• When the system runs abnormally, the software watchdog can restart.

Other Local Features

• Five-level user permission management allows an administrator to create more than one operation user and allocate them with proper permissions, which can be accurate to a certain channel.
• Complete logging and retrieval of operation, alarm, exception and information logs.
• Support for manual triggering and clearing of alarms.
• Support for import/export of device configuration information.

Network Features

• Support for TCP/IP protocol cluster, and also PPPoE, DHCP, DNS, DDNS, NTP, SADP, NFS, HTTPS and other protocols.
• Embedded WEB server.
• Support for unicast and multicast. For unicast, TCP, UDP, and RTP protocols are supported.
• Support for remote search, playback, download, locking and unlocking of video files.
• Support for remote fetching and configuration of parameters, as well as remote export and import of device parameters.
• Support for remote fetching of equipment running state, system log and alarm state.
• Support for system maintenance operations such as remote formatting, updating and rebooting of hard disk.
• Support for alarm port expansion through alarm host.
• Support for remote manual triggering and stopping of video recording.
• Support for remote manual triggering and stopping of alarm outputs.
• Support for remote PTZ control.
• Support for voice intercom or voice broadcast.

Development Support

• Provides SDK software development kits under Windows and Linux-based systems.
• Provides application software source code for demonstration.
• Provides development support and development training

services for application systems.

Notes:

• Product features list the main features available from our company’s NVR. Features depend on model specifications, intended purposes and configurations. The real product shall prevail.

1. Need-to-Know

Describe the parts and accessories that users must know before using NVR: front and rear panels, mouse, and how to operate the device through these parts and accessories.

• 1. Introduction to Front panel

Keys and indicator lights on the front panel are introduced.

Tiandy NVR Full Installation Guide

Read More :

• New Firmware for Chinese IPCAMERA
• Best FREE IP Camera Software for Windows
• Vivotek firmware DVR NVR IPC Software download

The front panel of PSE series NVR, TC-R14(20/40) configuration: I/B/N, TC-R54(20/40) configuration: I/B/N, TC-R3440 configuration: I/B/N,

TC-R5110 configuration: I/B/N, TC-R5220 configuration: I/B/N standard

series NVR is shown as below:

The functions of the front panel are shown in the following table:

The front panel of TC-R11(05/10/20) configuration: I/B/V2.0, TC-R31(05/10/20) configuration: I/B standard series NVR, TCR1120 configuration: I/B/V2.0 multimedia NVR is shown as below:

The functions of Status indicators on the front panel are shown in the

following table:

The front panel of TC-R58(20/40/80) configuration: I/B/N, TC-R38(40/80)

configuration: I/B/N, TC-R58(20/40/80) configuration: I/F,

TC-R38(20/40/80) configuration: I/F/N series NVR is shown as below:

The functions of Status indicators on the front panel are shown in the following table:

The front panel of TC-R516(40/80/160) configuration: E/B/N, TC-R31680

configuration: E/B/N series NVR is shown as below:

The functions of Status indicators on the front panel are shown in the following table:

• 1. Introduction to Rear Panel

The rear panel and interfaces of the equipment are introduced.

The interfaces on the rear panel of TC-R3105 configuration: I/B/P(/Z) series PSE NVR are shown as below:

Voice intercom input LAN Ethernet port

Alarm output

Power input

Earthing terminal

The interfaces on the rear panel of TC-R3210 configuration: I/B/P(/Z) series PSE NVR are shown as below:

The interfaces on the rear panel of TC-R3220 configuration: I/B/P(/Z) series PSE NVR are shown as below:

The interfaces on the rear panel of TC-R3220 configuration: I/B/P/H(/Z) series PSE NVR are shown as below:

The interfaces on the rear panel of TC-R11(05/10/20) configuration: I/B

TC-R31(05/10/20) configuration: I/B(/Z) series NVR are shown as below:

The interfaces on the rear panel of TC-R1230 configuration: I/B, TC-R12(10/20) configuration: I/B, TC-R32(10/20) configuration: I/B(/Z), TC-R5210 configuration: I/F, TC-R3210 configuration: I/F(/Z) series NVR are shown as below:

The interfaces on the rear panel of TC-R3105 configuration: I/F(/Z) series

NVR are shown as below:

The interfaces on the rear panel of TC-R14(20/40) configuration: I/B/N, TC-R54(20/40) configuration: I/B/N, TC-R3440 configuration: I/B/N(/Z) series NVR are shown as below:

The interfaces on the rear panel of TC-R58(20/40/80) configuration: I/B/N, TC-R38(40/80) configuration: I/B/N(/Z), TC-R58(20/40/80) configuration: I/F, TC-R38(20/40/80) configuration: I/F/N(/Z) series NVR are shown as below:

The interfaces on the rear panel of TC-NR2x enhanced series NVR (80 channels, 160 channels, 16 disk position) are shown as below:

The interfaces on the rear panel of TCR1120 configuration: I/B/V2.0 multi-media NVR are shown as below:

Note:

• The schematic diagram illustrates the functions of interfaces on the front and rear panels only, and the specific chassis size shall be subject to the real product.

• 1. Instructions to Mouse Operations

After your mouse is connected to the USB interface, you can use your mouse to operate the device. For information about available operations, refer to the following table:

1. Installation and Connection
   1. Precautions for Installation

Wr Warning:

Improper battery replacement is at the risk of explosion. The replacement operation is not recommended for users. To replace the battery, use the battery of the same type or equivalent type.

NVR is a special monitoring device which shall be installed by paying attention to the followings:

• Do not place containers containing (such as water glasses) liquid on the NVR.
• Install the NVR in a well-ventilated location. Install multiple devices such that they are spaced greater than 2cm.
• Operate the NVR under allowable temperature (-10°C ~ +55°C) and humidity (10% ~ 90%). (The H.265 series NVR with RAID mode enabled operates under 0°C ~ +55°C; the H.265 series NVR E16 with redundancy mode enabled operates under +20°C ~ + 55 ^).
• Please remove the power cord to cut off the mains power before cleaning the device.
• Dust on the circuit board within the NVR, when dampened, may result in short circuit. Please regularly brush out dust on the circuit board, connectors, chassis and fan. If dirt is hard to be cleaned, use water-diluted neutral cleaner to remove it and then dry it.
• Do not use volatile solvents such as alcohol, benzene or diluent to clean the device, neither strong or abrasive cleaners, which may damage the surface coating.
• Please purchase monitoring-level SATA HDD from regular channels to ensure the quality and use requirements of the HDD. Seagate monitoring-level HDD is recommended.
• Please ensure that there is no danger due to uneven mechanical loads.
• Please make sure that the video cable and audio cable have enough space for installation, and the bending radius of the cable should not be less than 5 times the outer diameter of the cable.
• Please ensure that the NVR is reliably grounded.

Note:

• When you receive this product, please check against the ” packing list” in the packing box. In case of any damage or missing accessories, please contact your vendor immediately.
  1. . Installing HDD

Our NVR device is not supplied with hard disk. A hard disk needs to be configured and installed according to your recording plan. Disassembly of the chassis and installation of the hard disk must be completed by professionals.

• Notes:

• Please use the NVR dedicated monitoring-level hard disk recommended by the hard disk manufacturer.
• For the maximum number of hard disks installed on the device, refers to the instructions in the hard disk document.
• Make sure that the power supply is cut off before installation commences.
  • 1. Calculation Method of HDD Capacity

Calculate the total capacity required for a hard disk video recorder according to the requirements of video recording (video type, video storage time), as detailed in the Appendix of this Manual.

Example:

8192 Kbps

3600 M

16384 Kbps

7200 M

Note:

The data provided in the table above is for reference only. The estimation of “file size” in the table may deviate from the actual value, and any loss caused thereby shall be borne by the user.

• • 1. HDD Installation Procedure

Installation tools

A cross screwdriver.

Installation diagrams (1) :

1 Remove the screws on the rear and sides of the chassis and then

remove the top cover.

2_S Connect one end of the HDD data cable to the SATA interface of the NVR master board Up, and the other end to the HDD.

3_S Connect one end of the HDD power cable to the SATA interface of the NVR master board, and the other end to the HDD.

4_S Fix the HDD screws on the bottom of the NVR chassis, attach the top

cover of the chassis and fix it with screws.

Installation diagrams (2) :

1 Remove the screws on the back of the chassis, remove the top cover,

and fix the hard disk to the chassis HDD holder.

2_S Connect one end of the HDD data cable to the SATA interface of the

NVR master board, and the other end to the HDD.

3_S Connect the power cable to the hard disk, attach the top cover of the chassis and fix it with screws.

Installation diagrams (3): (installation of the front HDD) 1 Attach the HDD mounting screws and insert it into the HDD slot on

the front panel.

1. Local Configuration and Operation
   1. Switch ON/OFF
      1. Switch ON

Note:

• Make sure to use the power supply required by NVR before

startup, and ensure that the NVR is well grounded.

• Make sure the NVR video output is properly connected to the monitor before startup.
• Abnormal power supply will result in malfunctioning of NVR or even damage. It is recommended to use stabilized power supply for power supply.

1. Connect the power supply and turn on the power switch on the rear panel. The device starts with a “beep” sound.
2. NVR displays the following screen at startup:

Tiandy
• * • •

4.1.2. Switch OFF

1. Select “Main Menu ->

” to enter the logoff interface, as shown in

the figure below.

Logout

Reboot

Shutdown

1. Users can click logoff to restart or shut down system.

Notes:

• Please do not cut off the power supply when the system is displaying “The system is shutting down…”
• Do not cut the power supply off when the device is running.
  1. Equipment Activation

After the device is started, the device can be configured with password and secret protection through device activation to ensure the normal login and password security of the device.

1. First, on the password setting interface, enter the password twice, and click Next to enter the next interface.

2_S On the graphic password setting interface, set an unlock pattern, and then automatically enter the password setting interface. ClickPrevious to return to the password setting interface, or click Skip not to set the graphic password.

3_S On the security question setting interface, set the mailbox and security question. You can skip this step directly into the boot wizard. The mailbox and security questions are used for password resetting.

• 1. Boot Wizard

After the device is started, the device can be simply configured through the boot wizard to ensure the normal operation of the device.

1. First, on the Setup Wizard interface, set the current language and resolution of output device. Click “Next” to enter the next interface.

1. On the Setup Wizard interface , select whether to run the boot wizard. Click “Yes” to enter the next interface, “No” to skip the boot wizard, or “Never” to close the boot wizard. In the third case, the boot wizard will be skipped at the next startup.

1. On the Authentication interface, a user shall log in as administrator

“admin” for authentication. Click “OK” to confirm the account. After

authentication is successful, the boot wizard appears. The device will be locked for 5 minutes if you input the wrong password for 5 consecutive times. Click Cancel to skip the boot wizard.

Permission Identification

Login as Administrator

ID

Password

Confirm

Cancel

Note:

• Administrator: admin, password: (boot password set in Section 4.2 Device Activation).

1. On the time and time zone setting interface, click “Apply” to set the time zone, time format and time; click “Next” to enter the next interface; and click “Exit” to exit the boot wizard.

1 2 3 4 5

Time&Time Zone S… Network card Server Search Format Disk Mobile Monitoring

(GMT+08:00)Beijing,Urumchi,Singapore

Time Zone

Time Format

Time

yyyy/mm/dd hh:mm:ss

2020-03-13 S 09:05:33

Next [ Exit

1. On the network setting interface, click “Back” to return to the previous interface; click “Next” to set network parameters and enter the next interface; and click “Exit” to exit the boot wizard.

Polymerization Op…

Network card

MAC Address

▼ IPv4 setting

IP Address

SubNet Mask

Gateway

Preferred DNS

Reserved DNS

IPv6 setting

Network cardl

I | Auto obtain IP address via DHCP

192.168.15 .34

255.255.255.0

192.168.15 .1

fl Get DNS automatically

8 .8 .8 .8

8 .8 .4 .4

Back j | Next j [ Exit

1. On the server searching interface, you can configure digital channels.

Click “Search” to search digital channels; click “Back” to return to the

previous interface; click “Next” to enter the next interface; and click “Exit” to exit the boot wizard.

IP Address

Modify IP

Activated

Protocol

Channel

MAC Address

Display

IPv4 v | Al I

“Next” to enter the next interface; and click “Exit” to exit the boot wizard.

For the non-activated IPC, the NVR password will be used t.

0 Sync password to get reserved information.

Search | | Back | | Next | | Exit

1. On the formatting disk interface, click “Initialize” to format the selected disk; click “Previous” to return to the previous interface; click

ote:

• The disk must be initialized before recording properly.

1. On the mobile monitoring interface, you can configure control devices on the mobile side. Click “Back” to return to the previous interface; click “Next” to enter the next interface; and click “Exit” to exit the boot wizard.

• Some device models use QQ for mobile monitoring. The real product shall prevail.

1. If there is still a hard disk in the system that has not been formatted, the following message as shown in the figure below will appear. Click “Execute” to automatically format the unformatted disks in the system one by one; and click “Back” to enter the preview screen directly.

Format Disk

Format disk will erase all the data, continue?

Cancel

Confirm

• 1. Cameras
     1. Adding Channels from the Shortcut Bar

Users can easily add an IP channel to the device with one click. If no channel is added, the preview status is shown as below.

1_X On the preview interface, click a channel to display the “+” sign, and the server search form appears, as shown in the figure below.

Note:

• A channel is added with default port, username and password; if not, you can choose “Custom Add”.

1. After the search is completed, double-click the search list or select the channel and click “Add” to complete the addition.
2. Users itself can also configure parameters to add digital channels. Click “Customized Adding” to display the “Customized Adding” form, as shown in the figure below.

1. Enter the IP address, port number, user name, password and other information of the front end.

Note:

• If it is the local channel of PSE-NVR and there is no connection, the add method of the PSE channel will automatically be changed to manual add after fast addition. The plug&play function is enabled by default for the POE port of the PSE series NVR. Please do not connect it to the LAN; otherwise, IP addressed of other devices in the LAN will be automatically modified.

4.4.2 Adding Digital Channels Using Regular Methods

1. Select “Main Menu -> Cameras -> Channels -> Basic Configuration” to

enter the channel configuration interface, as shown in the figure below.

Notes:

• This page displays different tabs for different device models.
• After addition is complete, you can check the results in the added device list.
• Click connect status O to directly preview the video of this channel.
• When the connection status displays an exclamation point, move

the mouse over the * icon to show the cause of the

connection failure.

1. Click “search” to begin searching. Search results are automatically sorted by IP address. You can modify the IP front end in the search results list. Click f to display the modify IP interface, as shown in the figure below.

1. Select the IP channel to add from the search list, click “Add” or double-click the mouse, and the IP device will be added to the idle

channel of NVR. You can add multiple IP channels. The channel search is shown as below.

PTZ Setting ^{Added Devices}

Video Loss Search I Add Quick Add I Customized… □ Enable S+(first access I… Display IPv4 v All

Delete

1. When adding an inactive IPC, an activation pop-up window will

appear as shown in the figure below. Check the “Synchronize

information retained for retrieving the password”, the retained

information will be synchronized to the front end and activated.

For the non-actlvated IPC, the NVR pas…

Sync password to get re…

• If the add method for PSE-NVR’s digital channel is plug and play,

then this channel is busy.

Customized Adding

1 On the Channel Config -> Basic Configuration interface, click

“Custom Add” to enter the digital channel interface; when device type

is private protocol, proceed as shown in the figure below.

2_S Select the channel number to add, check Enable, and select the connection mode according to the device type. When device type is RTSP, proceed as shown in the figure below.

When device type is ONVIF, proceed as shown in the figure below.

1. After entering the IP address or URL address and username and password of the front-end device, click “OK” to add a digital channel. Repeat this operation to add other digital channels.

Notes:

• If the device to add is a multi-channel NVR, you can select the channel number to add from “Channels”, and also can add multiple channels for one NVR at a time.
• Continue adding, batch adding, adding according to the add rule and target channel, and skipping the current channel if the

current channel is included in the target channel. If the IP address

is ascending, the last bit of IP, after 255, will not be incremented.

• When device type is ONVIF, the port number defaults to 80, and the username and password default to admin. The login account and password may vary from manufacturer to manufacturer, which needs to be modified according to the actual situations.

4.4.3 Adding POE Camera 1 On the Channel Config -> Basic Configuration interface, click f in

the added device list or double-click a PSE channel to enter the digital

channel interface.

2_S A PSE channel can be added by means of “Plug & Play” and “Manual Add”:

1. If “Manual Add” is selected, the device shall be connected to the network interconnected with IP channels. Other configuration methods are the same as adding ordinary digital channels.
2. If “Plug & Play” is selected, the front end to add shall be connected to the device’s independent POE-powered Ethernet port. The device will

complete the connection automatically.

• • 1. Quick Add

In order to allow users to quickly add devices, users can choose to enable the “Quick Add” function to add channels. In this mode, the device will be automatically searched and added to the digital channel.

^Notes:

• The “Quick Add” function will automatically search for IPC and add it to the idle channel. Please pay due attention when using it.
• The PSE device channel list cannot be removed manually.
  • 1. Configuration Management

Users can import and export all channel parameter configurations through configuration management.

1. Select “Main Menu -> Cameras->Channels -> Config” to enter the configuration management interface. If a mobile storage device is connected, clicking Export can export all channel configuration parameters, which are saved as .xls format file. Users can manually edit exported parameters on the computer and use them as input parameters, as shown in the figure below.

1. Importing contents contained in the exported .xls file shall meet the following formats.

Wherein:

1. In “Enable “, 0: channel not enabled, 1: channel enabled;
2. In “Chn Type “, 0: main stream, 1: secondary stream, 2: picture stream;
3. In “Net Mode “, 1: TCP, 2: UDP, 3: multicast;
4. In “Connect Mode “, 0: IP, 1: domain name, 2: active mode;
5. In “Preview Mode “, 0: tiled on the display area, 1: wide-screen proportional display is maintained.
6. Exported .xls files can be edited with Office 2003 and above and imported into the device.
   • 1. IPC Central Management

The centralized management function of IPC allows users to import and export parameters of the added front-end devices, upgrade them remotely, and restart IPC.

1. Select “Main Menu -> Cameras -> Channels ->IPC Central

Management” to enter the IPC centralized management interface, as shown in the figure below.

• The interface can display the channel number, property, version

number and connection status of the added front-end device,and allow perform cloud upgrade, parameter import and export, remote upgrade, IPC restart and other operations.

1. Configuration Import/Export
2. Select the front end to operate from the added device list.

(2) Click “B”

to display the configuration import prompt box, as

shown in the figure below.

Configuration Import

Import parameters can lead to reboot of front terminal IPC, whether to continue?

Cancel

Confirm

(3) Click “ok” to enter the configuration import interface, as shown in the figure below.

(4) Select the configuration file and click “Import” to quickly import

the configuration into the front-end device.

(5) Export the front-end configuration parameters, and click

“B” to

display the configuration export interface, as shown in the figure below.

Configuration Export

Export to

File name

USB1-1

Export

Cancel

1. Select the storage device, fill in the name of the export file and click “Export” to export the front-end configuration. The prompt form pops up after export is successful, as shown in the figure below.

Export Successed

Config file exported.

Confirm

1. Remote Upgrade and IPC Restart
2. Select the channel to upgrade or restart from the added device

list.

(2) Click ”

” to display the IPC Upgrade interface, as shown in the

figure below.

IPC Upgrade

Upgrade file list 3.box uuu.box

Refresh

Upgrade

Back

(5) Click ”

(4) Click ”

1. Select the configuration file to upgrade, and click “Upgrade” to complete the IPC upgrade.

” to remotely restart the selected device.

” to display the Restore Defaults prompt box, as shown in the figure below.

(6) Clicking “OK” and selecting IPC will restore defaults and restart

IPC.

(7) Click “D”

to display the Cloud Upgrade prompt box, as shown in

the picture below.

1. Import Broadcast/Start Broadcast
2. Click Import Broadcast to display the IPC Upgrade interface, as

shown in the figure below.

1. Select the configuration file to upgrade, and click “Upgrade” to complete the IPC upgrade.
2. After the upgrade is completed, click the Start Broadcast button to the Start Broadcast prompt box, as shown in the figure below.

Start broadcasting

This operation will activate all the IPC alarm sound, continue or not?

Cancel

Confirm

1. Click OK, and all IPCs will begin to play the imported audio.
   • 1. POE Power Information

This function is available in the PSE series NVRs while unavailable in other models.

1. Select “Main Menu -> Cameras -> Channels ->POE Power Infomation” to enter the POE power information display interface, as shown in the figure below.

Tiandy

Channels

Stream Setting

Three Smarts Sett…

Video Setting

OSD

Motion

Mask Alarm

Alarm Input

Video Loss

PTZ Setting

Basic Configuration Config IPC Central Management POE power information

Instruction: check the check box of corresponding channel to use long-distance network cable, while uncheck it to use short-distanc…

Notice:

1. Device POE rated power is200.0W.
2. Each POE port power range:0~30W.
3. When actual power exceed rated power, system will close POE port by port number by descending, till the actual power go lower than rated power.

Note:

” /!” means that the POE port is normally powered, and ” ■ ” means that the port is not connected to a camera or powered normally.

• Above the “?” port is the real time power information of the POE port.

Please refer to the interface for POE power notes.

• • 1. Code Setting

Select “Main Menu -> Cameras -> Stream Setting” to enter the code setting interface, as shown in the figure below.

Audio/Video Parameter

Select the channel to set and set audio and video parameters:

• Channel: select the channel where you want to set parameters. There are four types of video compression parameters: main stream (normal), main stream (alarm), custom 1, and custom 2.
• Encoding: The system supports H.264 and H.265 encoding, and high profile, main profile and baseline encoding methods are available.
• S+: S+ will display and distinguish the main and secondary streams according to whether it is supported by the front end. After S+ is turned on, compression mode, video quality, I frame rate and key areas will not be available. Some front ends also support mutual exclusion of S+ and intelligent analysis. When S+ is turned on, the intelligent analysis will be turned off.
• Resolution: Sets the resolution of the front-end device.
• Corridor Mode: Enables the corridor mode when resolution is 16:9 (for example, 1080P). When corridor mode is enabled, the resolution of the video is adjusted to 9:16.
• FrameRate: Video frame rate refers to the number of video frames per second that can be selected or edited from a drop-down list.
• BitRate Type: variable bitrate and fixed bitrate. The variable bitrate will change according to the scenario, and the fixed bitrate will be coded according to the set bitrate as far as possible.
• BitRate: Can be selected or edited from the drop-down box, range: 32-16384Kbps.
• Stream type: The composite type provides two options: “Pure Video” and “Audio Video”. “Audio Video” means containing video and audio information, while “Pure Video” contains only video information.
• Click “More” to display the image quality, I frame rate, audio encoding, audio control type, and input volume setting options.
• Quality: 5 options including best, better, good, average, poor. Image quality is proportional to the bitrate. The better the image quality is, the higher the bitrate is.
• I-Frame Interval: I frame, also known as key frame, One I frame is contained in several video frames. If I frame rate is 100, there is one I frame in every 100 frames of video. I frame rate inversely proportional to the bitrate. The higher the I frame rate is, the smaller the bit rate is. It is recommended that the I frame rate be the same as frame rate.
• Audio: The system provides 3 audio encoding modes: ADPCM_D(ADPCM_DIV4), G.711A and G.711U. Three audio sampling rates of 8K, 32K and 48K are also provided.
• Audio Type: Audio control type used by the front end: Lineln and MicIn.
• Input volume: The input volume of the corresponding channel, ranging from 0 to 100.
• Audio output type: Laser-enabled devices also support the selection of audio output type, including built-in speaker, external audio source and off. When a built-in speaker is selected, you can adjust the output volume.
• The secondary stream can be set separately. For setting methods, refer to the main stream.

Notes:

• When bitrate type is selected as “fixed bitrate”, the image quality is unavailable.
• Secondary stream parameters are used for network transmission. When the network environment is not very good, users can use the secondary stream for preview and storage to reduce the bandwidth. In addition, the secondary stream is also suitable for mobile monitoring.
• For corridor mode, this should be supported by the front-end IPC.
• Coding parameter templates vary with different front-end IPCs.
• Click the More button to display or hide the setting options under the button.

ROI

The focus area can be set here after a front-end that supports it is connected. The image displayed in the focus area is of higher quality.

1. Select the property page of the focus area, as shown in the figure

below.

1. Check “Area Setting” to enable this function. Press and hold the left mouse button and drag over the video to set the focus area. Up to four focus areas are supported. Click “Delete Area” to delete all the focus areas that have been set.
2. Click “Apply” to save the settings.

4.4.9 Video Setting

In order to obtain a good visual effect, users can adjust video parameters of the front-end according to the scenario, and the adjusted parameters will apply to local preview, video recording, network preview, etc.

Select “Main Menu -> Cameras -> Video Setting” to enter the HD parameters interface, as shown in the figure below.

HD parameters

1. Select the channel to set.
2. Set system, video rotation, mode and other parameters.

Notes:

• Brightness, contrast, saturation and chroma can be adjusted between 0-100.
• The shutter speed is adjustable between 1/100000 – 1. The higher the set value is, the faster the response is.
• Auto gain is adjustable between 0 and 100.
• Ultra-wide tendency policy has three options: Off, Auto and Manual. The ultra wide tendency rating is displayed when the Ultra wide tendency policy is not turned off, and the value is adjustable between 0 and 100.
• Image enhancement includes image style, indoor and outdoor modes, digital noise reduction and noise reduction level. Image style includes adaptive, natural, bright, soft and sharp; Indoor and outdoor modes include indoor and outdoor; Digital noise reduction has three options: Off, Normal and Expert. When the normal mode is selected, the noise reduction level option is displayed, and the value is adjustable from 0 to 100. When the expert mode is selected, there will be the space-domain noise reduction level and the time-domain noise reduction level options, and the value is adjustable from 0 to 100.
• White balance has options including automatic, semi-automatic, sunny day, fluorescent lamp, warm light, incandescent lamp, natural light, lock and manual. Manual and semi-automatic can be the value between 0 and 50.
• The Copy to Channel function can be used to copy the set parameters.
• Use the mouse wheel to adjust video input parameters, or you and Q icons to increase or decrease the value.

can also click lU

1. After setting, click “apply” to save setting parameters.
2. Restore Defaults is to allow the camera directly to restore the defaults of all parameters on this page.

High-definition template

1. Select the channel for the HD template you want to set.
2. HD templates are divided into indoor, outdoor, sports, wide

tendency, low light, high light, bright, custom, as shown in the figure below.

Tiandy

Channels

Stream Setting

Three Smarts Sett…

Video Setting

OSD

Motion

Mask Alarm

Alarm Input

Video Loss

PTZ Setting

EaztoiiiioHESX

Playback Backup Alert Ma… VCA Cameras Storage … Alarm Se… System S… System … 0 0

Image Set High-definition template

Channel

Day

Night

D/N Set

[17]Channel 1

Outdoor

Outdoor

Reset To Def… j j | | Back

D/N Set

1. Select the channel where you want to set Color to Black.
2. Color to Black types are divided into color, black and white, timer, inter-sync, exter-sync, day and night and adaptive.
3. Timer is shown in the figure below.

Notes:

• Daylight hours and dark hours can be set to a time range of 00:00-23:59, and the dark hours must be later than dawn time.
• The Color to Black mode depends on the front end.

4_X Exter-sync is shown in the figure below.

otes:

• Daytime and night brightness values can be adjusted from 0 to

100, or you can click the o and icons to increase or

decrease the value. E3

• The Color to Black delay and Black to Color delay can be adjusted

between 0 and 120s.

5_X Inter-sync is shown in the figure below.

Notes:

• Daytime and night brightness values can be adjusted from 0 to

100, or you can click the s or Q icon to increase or decrease

the value.

• The Color to Black delay and Black to Color delay can be adjusted

between 0 and 120s.

6_X The day and night mode is shown in the figure below.

Notes:

• The day and night mode includes automatic, daytime and nighttime.
• The sensitivity is divided into high, medium and low.

7. The adaptive mode is shown in the figure below

Note:

• Day/night brightness values can be adjusted from 1 to 100.
• The effective delay time for Color to Black/Black to Color is 0-120 seconds.

4.4.10. OSD

1. Select “Main Menu ->Cameras ->OSD ” to enter the OSD overlay parameter setting interface, as shown in the figure below.

OSD Overlay

1. Select the channel to be set OSD.
2. Set OSD for the channel.

To change the OSD position of the channel, check the custom position, and directly drag the mouse OSD box to set it.

Notes:

• OSD overlay includes channel name, date, week day, 12-hour system, date format, time format, OSD color, background color, etc.

Video Occlusion

The video occlusion function can occlude some key areas on the video.

1. Select the channel to set video occlusion.

2. Drag the mouse to set the video occlusion area.

PTZ Privacy Mask

1. Select the channel to set dynamic privacy occlusion.

1. Control the PTZ via the shortcut PTZ control panel to switch to the screen you want to occlude.
2. Drag the mouse to set the video occlusion area and click “Add Area”.
3. The added area is shown in the list on the right. Click “Delete Area” to delete areas.

NO Note:

• This section applies to a front-end IPC that supports this

functionality.

4.4.11 Motion 1. Select “Main Menu -> Cameras-> Motion” to enter the motion

detection setting interface, as shown in the figure below.

2. Select the channel to set motion detection.

1. Set the motion detection arming time, detection area and sensitivity, as follows:
2. Check “Enable”.
3. Enter the “Deployment Time” to set the motion detection arming time.
4. Draw the area to be detected on the video of the channel with the mouse.
5. Adjust the sensitivity on the sensitivity slider. The higher the sensitivity value is, the more sensitive the motion detection is.
6. Enter the “Linkage Setting” to set the motion detection and alarm linkage.
7. Alarm linkage voice prompt, screen display, sending email, linkage video, linkage output, linkage snapshot, linkage text preplan, linkage single screen and linkage double light are available for setting.
8. After setting, parameters of other channels can be copied.

5_S Click “Apply” to save the settings parameters.

J Note:

• Double lights can be linked after front end devices supporting

double lights are connected.

• • 1. . Mask Alarm

1 Select “Main Menu -> Cameras -> Mask Alarm” to enter the occlusion

alarm interface, as shown in the figure below.

2_X Select the channel to set video occlusion.

3_X Check “Handle Video Occlusion” to process the occlusion alarm.

4_X Select “Linkage Setting”. When an alarm occurs, you can link voice prompt, screen display, sending email, linkage video, linkage output, linkage snapshot, linkage text preplan, and linkage single screen, etc.

5_X After setting, you can copy the parameters from other channels. Click “Apply” to save the set parameters.

• • 1. Alarm Input

By setting alarm inputs, when input alarm occurs in the front-end IPC, the NVR device can be linked to provide prompt, video, etc.

1. Select “Main Menu ->Cameras -> Alarm Input” to enter the alarm input setting interface, as shown in the figure below.

Channels

Stream Setting

Three Smarts Sett…

Video Setting

OSD

Motion

Mask Alarm

Alarm Input

Video Loss

PTZ Setting

Input Port No.

Input Port Alias

Circuit Type

Remote Alarm Input 2

Remote Alarm Input 2

Normally open

1 □ Enable

Deployment time Linkage setting

Copy To Port _AN v I Copy

I Apply | Q Back

1. Select the input port number to set.
2. Select Annunciator Type.

nO Note:

• Normally-open alarm: active when the alarm input port for the

front-end IPC is closed.

• Normally-closed alarm: active when the alarm input port for the front-end IPC is open.

1. Check “Handle Alarm Input” to set the arming time of alarm input.
2. Enter “Linkage Setting” to set alarm linkage.
3. Options include alarm linkage voice prompt, screen display, sending email, linkage video, linkage output, linkage snapshot, linkage PTZ, linkage text preplan, linkage single screen, etc.
4. After setting, parameters of other channels can be copied.
5. Click “Apply” to save the settings.
   • 1. Video Loss

Set the video loss alarm. When video loss occurs in a channel, it is linked to the NVR device for prompt, recording, etc.

1. Select “Main Menu -> Cameras -> Video Loss” to enter the video loss setting interface, as shown in the figure below.

Tiandy

Channels

Stream Setting

E

Playback

B

Backup

Alert Ma…

iid

VCA

[01]Channel IChannel IChannel IC’/

Q H

Cameras Storage …

E 3 X

Alarm Se… System S… System …

Three Smarts Sett…

Video Setting

OSD

Motion

Mask Alarm

Alarm Input

Video Loss

PTZ Setting

Deployment time Linkage setting

0 Enable

Copy To

Copy

1. Select the channel to set video loss.
2. Check “Handle Video Loss” and set the arming time for video loss.
3. Enter “Linkage Setting” to set alarm linkage.
4. Options include alarm linkage voice prompt, screen display, sending email, linkage video, linkage output, linkage snapshot, linkage PTZ, linkage text preplan, linkage single screen, etc.
5. After setting, parameters of other channels can be copied.
6. Click “Apply” to save the settings.
   • 1. PTZ Setting

Set the PTZ control protocol and serial port property for a channel.

1. Select “Main Menu -> Cameras -> PTZ Setting” to enter the PTZ

setting interface, as shown in the figure below.

1. Select the channel to set.
2. Select the PTZ control protocol, address and serial port of the channel. Once the setup is complete, parameters of other channels can be copied.
3. Click “Apply” to save the settings.

NO Note:

• Users can customize the serial port properties to set the baud rate, data bit, stop bit and check bit of the serial port, and choose to copy these set parameters to other channels after setting.

• • 1. Three Smarts Setting

For the three smarts camera, the intelligent three smarts setting can be used to carry out motion detection.

1. Select “Main Menu -> Cameras -> Three Smarts Setting” to enter the basic setting page, as shown in the figure below.

1. Select the channel to set motion detection to set the sensitivity, and select to enable intelligent coding, intelligent image and intelligent alarm. Click the Apply button.
2. Set the motion detection area, as shown in the figure below.

1. Set the arming time as shown in the figure below.

Tia ndy

E

Playback

a

Backup

Alert Ma…

iki

VCA

Cameras

H E S X

Storage … Alarm Se… System S… System …

Channels

Stream Setting

Three Smarts Sett…

Video Setting

OSD

Motion

Mask Alarm

Alarm Input

Video Loss

PTZ Setting

Basic Configuration Smart Alarm Parameter

Channel [06]Channel 1

Area Setting Deployment time Linkage setting

Copy To

Copy

Back

1. Enter the “Linkage Setting” to set the motion detection alarm linkage,

as shown in the figure below.

1. Options include alarm linkage voice prompt, screen display, sending email, linkage video, linkage output, linkage snapshot, linkage text preplan, linkage single screen, etc.
2. After setting, parameters of other channels can be copied.
3. Click “Apply” to save the settings.

4.5 Preview

• • 1. Interface Status

On the preview interface, the video recording and alarm status of each channel can be distinguished by the icon on the upper right of each channel. For description of preview status, please refer to the table below.

4.5.2 Task Bar Menu

In preview state, the task bar allows for preview screen switch, preview setting, output mode, alarm clearing, alarm information viewing, network setting, mobile monitoring, time setting and other operations, as shown in the figure below.

Taskbar diagram of main port

Taskbar diagram of auxiliary port

Descriptions of main port taskbar items

Notes:

• To use the “Custom Preview” action, set the “Custom Preview” configuration in the Preview Setting.
• To use “Start Switching”, set “Cruise Interval” in the Preview Setting.
• Android and IOS clients are available for mobile monitoring, and the status of public network connection can be checked.
• TC-NR1016M7-S8, TC-NR1032M7-S8, TC-NR20xxM7-S8,

TC-NR20xxM7-E8, and TC-NR20xxM7-E16 are set with main and auxiliary ports, while other models have no auxiliary ports.

Description of auxiliary port right-click menu item

Custom Preview

Users arrange some specific channels according to the specific number of screens on the same screen as needed. When you select a configuration from the “Custom Preview” popup menu, the preview becomes this display screen.

Single Screen

Switches the current screen to a specified channel. Select a channel in the “Single Screen” pop-up menu, that is, selecting the channel for preview.

Multi-screen

Modify the display mode of the output device. The system supports 1/3/4/6/8/9/10/13/16/20A/20B/25/32/36/40/64 screen preview. If the multi-screen preview is selected, the preview is done according to this number of screens.

J Note:

• For TC-NR20-S series and TC-NR20-E series NVRs, except for 20-channel devices, VGA1/HDMI1 supports up to 64 screens and VGA2/HDMI2 supports up to 32 screens. The maximum number of supported screen is subject to the specific model.

Page UP/Down

Click the “Previous ” button on the taskbar to switch to the previous screen, and click the “Next” button to switch to the next screen.

Start/Stop Switching

After calling out the taskbar on the main port/auxiliary port, select “Start Switching”, and the main port/auxiliary port will start switching according to the set cruise sequence; Select “Stop Switching” to stop switching.

4.5.3 Shortcut Preview

1. In preview state, select the channel to operate by using the left mouse button. The shortcut bar is shown below the red box, as shown in the figure below.

1. The shortcut menu can be used for PTZ control, instant playback,

manual snapshot, digital zoom, intercom and channel information

Instant Playback

Playback videos within 5 minutes of the channel. If there is no video available in the channel, the “Instant Playback Failed” message will be display.

Digital zoom

1_S Click to enter the digital zoom interface, as shown in the figure

below.

Original video:

Screenshot of the digital zoom effect:

2_S Scroll the mouse wheel to zoom in or out. The zoom-in or -out area is centered around the current position of the mouse.

3_S You can also click “+” in the upper left corner of the screen to zoom in and “-” to zoom out. Zoom-in and -out are done around the center of

the current screen.

4_S When zooming in, the left mouse button can still drag and drop the image to change the zooming area.

1. Click the right mouse button to exit digital zoom.

Note:

• Depending on the processing capacity of the equipment, the

maximum magnification time is 8 times or 16 times.

High Flow/Low Delay:

When High Flow is selected, the NVR devices will ensure fluency based on network traffic. When the Low Delay mode is selected, the video delay is reduced.

• • 1. Preview Parameter Setting

1. Enter “Main Menu -> System Setting -> Preview Setting”, as shown in the figure below.

Tiandy

D H E

Cameras Storage … Alarm Se…

s

System S…

X

System …

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

E

Playback

a

Backup

■id

VCA

Basic Configuration View configuration Customized Preview

0 Self-adaptive optimum resolution

Cancel

1. Description of the Preview Setting -> Basic Configuration interface:

• Output device: select a video output device from the “output device” drop-down list: HDMI2/BNC, VGA/HDMI, VC (VC is shown here when the last channel is set as the virtual composite channel).
• Output resolution: 800*600, 1024*768, 1366*768, 1440*900, 1280*800, 1280*720, 1920*1080, 2560*1440, 2560*1600,

3840*2160, etc. The list items may vary with devices.

• Automatic detection: Adaptive to the best resolution of the monitor.
• Cruise interval: Sets the preview automatic switching time interval. Options include no cruise, 2s, 3s, 5s, 10s, 15s, 30s and 60s.
• Preview mode: set screen number configuration, including 1, 3, 4, 6, 8, 9, 10, 13, 16, 12 A, 12 B, 25, 32, 36, 40, 64, etc. The list items may vary with devices.
• Main port setting: This setting is available in TC-NR1016M7-S8, TC-NR1032M7-S8, TC-NR20xxM7-S8, TC-NR20xxM7-E8, and TC-NR20xxM7-E16, while unavailable in other specifications.
• Output mode: Sets VGA output display effect. Options include standard, soft, bright, and highlight.
• Alarm screen switching interval: Sets the time interval of alarm linkage single screen display. Options include 2s, 3s, 5s, 10s and 15s.
• Keep the last frame: With this option configured, the preview will stay on the last frame after the front camera is disconnected. Otherwise, “No Video” is displayed.

1. Description of the Preview Setting -> View Configuration interface

Tiandy

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Basic Configuration View configuration

Customized Preview

Select the screen number on the right, double-click the screen to delete the preview channel, and double-click the channel number in the table on the left to configure the channel number to the specified location. To open or close all preview channels, click Auto Configure and Clear All on the lower right.

Notes:

• The standard series NVRs (16-channel 8-disk position, 32-channel 8- disk position) have two kinds of output devices: HDMI2/BNC and VGA/HDMI1.
• The TC-NR20-S series and TC-NR20-E series NVRs (TC-NR20xxM7-S8, TC-NR20xxM7-E8, TC-NR20xxM7-E16) have two kinds of output devices: VGA1/HDMI1 and VGA2/HDMI2.
• The multimedia NVR series (20-channels 1-disk position) have one kind of output device: HDMI/VGA.
• When the maximum preview performance is switched from the main stream to the secondary stream, as the secondary stream is non-composite audio by default, there may be no sound in the UI preview. Due to the limitation of device performance, when the access stream reaches the upper limit of device performance, it cannot continue to connect to other streams.

1. Description of the Preview Setting -> Customized Preview interface

The left and middle sides of the interface are used the same way as the view configuration interface. When the channel is configured, click the arrow between middle and right to add the configuration to the preview template. The maximum number of supported templates is 8. After configuration is completed, click “Apply” in the lower right corner to make it effective. Selecting the preview template can change the channel and screen number configuration. Double-click can change the template name. Preplan application is used in the right-click menu of preview screen.

• • 1. Preview Interface Message

Limited Decoding Performance

When the decoding performance of the device reaches the upper limit, the device will display the message as below: “Decodingperformance reaches the upper limit, please manually disable part of channels”. You can configure whether to enable the message. For details, see the System Settings -> General Settings. It is not enabled by default.

System Exception Message:

When the options in System Settings -> Route Maintenance ->

Network Exception/Storage Exception are enabled and related exception

events occur, the

icon in the upper right corner of the screen will

become the

icon. Double-click on the icon will open the system

notification interface, as shown in the figure below.

Alarm Information

Abnormal alarm

Time Title Type Content

• Users can choose not to display the message, or click “Next” to

check the next message.

When an anomaly alarm regarding the risk of video loss occurs, a red warning form will appear to alert the user to deal with the abnormal alarm in time, as shown in the figure below.

Abnormal notice

[03-17 11:50:05]No valid disk.

Please handle it timely. Otherwise there is a risk of losing the videotape.

Later process… Processing

Alarm Message:

In intelligent analysis, when linkage call is set for the channel and

when an alarm occurs, a single screen of the corresponding

channel appears, and the

icon flashes in the upper right

corner of the screen. Clicking the icon can open the calling, and at

this point, the icon becomes

. Clicking the right mouse

button can exit the alarm.

• • 1. Audio Preview and Intercom

Audio Preview

After selecting a video channel with mouse or remote control, the system will automatically play the audio of that channel.

Voice Intercom

Users can use the voice intercom interface of the device to realize the intercom function between the remote control end and the device. Please connect the pickup and speaker before intercommunication.

• • 1. Right Back to Preview Interface

On the parameter configuration interface, right-click to return directly back to the preview interface.

4.6 PTZ control

• • 1. PTZ Parameter Setting

Notes:

• Before controlling the dome camera or PTZ of the IP channel, please first confirm that the network is normally connected between PTZ decoder and NVR, and configure the parameters of the PTZ decoder in the device.
• For parameter setting of front-end IPC serial port, see section 4.3.15.
• For parameter setting of NVR local serial port, see System Settings.
  • 1. PTZ Control

1. In login state, enter the preview state. Use your mouse to click the channel preview screen that requires PTZ control. Click the “PTZ” button in the preview shortcut menu bar to enter the full-screen screen of the channel, and the PTZ control form appears, as shown in the figure below.

1. Select the channel for PTZ control.
2. Description of PTZ control:
3. PTZ control: Use your mouse to click the DQOU button to control up, down, left and right actions of the PTZ; use your mouse to click the □□□□ button to control the tilt actions of the PTZ; click the s button to start or stop the automatic pan operation of the PTZ.

2) Lens control: click the

button on the left of the “Aperture” to

turn off lens aperture; click the

button on the right to turn

on aperture; click the

button on the left of the “Focus” to

zoom.

enable far focus; click the

button on the right to enable

close focus; click the

button on the left of the “Zoom” to

reduce zoom; and click the

button on the right to increase

1. Speed setting: click the progress bar to select a value or scroll the mouse wheel to change a value, or click the or icon to increase or decrease the value. The higher the value is, the action speed of the PTZ is greater. The value is L2 by default.
2. Click the B icon to set the one-key focus function, click the

icon to enter the 3D positioning function interface, and click the icon to set ON and OFF of the front-end laser.

icons to expand and hide the control menu on

5). Click 0 and H

the right, as shown in the figure below.

6 ) Drag the km icon to drag the PTZ control form.

icon to zoom out the PTZ control form. In PTZ

7 ) Click the

zoom-out state, click the

icon to return to the PTZ control

form. In PTZ zoom-out state, press and hold the left mouse button to control the PTZ direction of the dome camera according to mouse movement direction.

1. 6.3 Preset Position, Cruise, Trajectory Settings and Recalling

Preset Position Setting and Recalling

1 Recall preset position: Selects a preset position number from the “Preset Position” drop-down list, or enter the preset position number directly and click the “Recall” button to recall the selected preset position.

2_S Set preset position: after controlling the PTZ to act to a specific position, select the preset position number from the preset position drop down list or directly input the preset position number, and click “Set” button to complete setting the preset position of this position number.

Trajectory Recording and Demonstration

When you click the “Start Trajectory” button, the button message changes to “End Trajectory”, and the system enters the trajectory recording state. At this point, the system will automatically record all operations on the PTZ before users click the “End Trajectory” button. After pressing the ” End Trajectory” button, the trajectory recording is completed and the system will automatically exit the trajectory recording state. Users can click the “Demo Trajectory” button to demonstrate the trajectory just recorded.

Cruise Path Setting

1. Click the “Cruise Path” button to enter the cruise path setting interface,

as shown in the figure below.

1. Cruise path setting are described as follows:
2. View cruise path information

Select a cruise path number from the “Path Number” drop-down list. After selecting a cruise point, the system automatically displays the preset position corresponding to the cruise point and the

duration of stay in the preset position.

1. Edit cruise path

Select the path number you want to edit from the “Path Number” drop-down list. If the path is disabled at this point, press the “Enable” button to enable the cruise path. Select the preset position number from the “Preset Position” drop-down list, and press “Add” after entering the time, the preset position will be added to the cruise point list of the cruise path. After selecting a cruise point from the cruise point list, click the “Delete” button to remove the cruise point from the cruise point list of the cruise path.

After a cruise point is selected, select a preset position from the preset position dropdown list, and click the “Set” button after the time is entered to modify the configuration information of the selected cruise point.

1. Enable/disable cruise path

Select a cruise path number from the “Path Number” list to enable or disable the path.

1. Recall/stop cruise path:

Click the “Recall” button to cruise according to the set path. Click “Stop” to stop the current path cruise.

1. Exit the cruise path setting interface

Click the “OK” button to save all the path editing operations on the cruise path setting interface into the system, and then exit the path setting interface. When pressing the “Cancel” button, the system will automatically ignore all editing operations and exit the path setting interface.

1. 3D positioning

Users can select any area on the video screen with the mouse, and the system will automatically control the action of the PTZ lens to realize the zoom-in/out function of the display scene (drawing a rectangle from left to right for zooming in from and right to left for zooming out).

4.6.4 USB Keyboard Controlled PTZ

1. In preview mode, select the channel for PTZ control by using [t] [I] keys and press P. At this time, the system will display the selected channel on a single screen. The upper right corner of the screen displays “PTZ ChnXX” to alert users that the system is in the PTZ control state of the XX channel.
2. Controlling PTZ Actions

• PTZ control: In the PTZ control mode, press [t][l][^][^] keys to control the PTZ up, down, left and right; Press the “Enter” button, the PTZ starts automatic pan action and press the “Enter” button again, the PTZ stops automatic pan action.
• Lens control: In the PTZ control mode, press I or G to turn on the lens aperture; press Ctrl+I or Ctrl+G to turn off the lens aperture; press Z or B to zoom in; press Ctrl+Z or Ctrl+B to zoom out. Press F or J to enable far focus; and press Ctrl+F or Ctrl+J to enable close focus.
• Recall preset position: In PTZ control mode, press the [Backspace] key, and then [Number] key, and then [Enter] key, the system will recall the corresponding preset position.
• Speed setting: In PTZ control mode, press the numeric keys [1] – [4] to set the speed of the PTZ.
• Exit the PTZ control mode: Click [ESC] in the PTZ control mode to return to the preview mode.

4.7 Storage Setting

• • 1. Recording

Basic

1. Select “Main Menu -> Storage Setting -> Recording -> Basic ” to enter the recording interface, as shown in the figure below.

Tiandy

Recording

Parameter

Images Setting

Diskgroup Allocation

Reindex

Playback

Channel

a

Backup

Alert Ma…

iki

VCA

a

Cameras

E S X

Storage … Alarm Se… System S… System …

Basic Advanced Holiday Plan

[01]Channel 1;£ v 0 Audio Recording 71 Redundant

I I I-frame Record

10 xz f Reset

[Mainstream x’

PreRecord(s)

Dwell (days)

Copy To

PostRecord(s)

StreamType

Back

1. Select the channel to set.
2. Select whether to “Audio Recording”, whether to enable “Redundant “, and whether to enable “I-frame Record”.

• When “Audio Recording” is not checked, only video data is saved in the video file.
• When there are redundant disks in the system and the “Redundant” function is enabled on the selected channel, recordings and captured image files will be saved in both the recording disk and redundant disk.
• If “I-frame Record” is enabled, the system will posterize video files, which can greatly save the hard disk space for the videos of non-key areas.

1. Select video type. Options include “Schedule”, “Port Alarm”, “Motion”, “Video Loss”, “Video Mask”, “Motion/Port”, “Motion&Port”. You can check “Cancel” to delete the set video types.
2. Press and hold the left mouse button and drag over the time zone, and the selected time zone will be updated as the specified video type.
3. Set the pre-recording and delay time of alarm videos.

• PreRecord: Assuming that the pre-recording time set by the user is 5s, the system will automatically save the video information to the video file 5s before alarming.
• PostRecord: The delay time of video is applied to the alarm video. Assuming that the delay time set by the user is 5s, the system will automatically save the video information to the video file 5s after alarming ends.
• The combination of prerecord and postrecord: can facilitate the user to analyze the monitoring information before and after the occurrence of alarms.

1. Dwell : Set the maximum retention time of videos in days. 0 means no restriction, and the maximum retention time of videos is 120.
2. StreamType : Set the stream type of videos, including MainStream and SubStream. Some models also support dual stream recording.
3. Click “Apply” to save the configurations.

Advanced

1. Select “Main Menu -> Storage Setting ->Recording -> Advanced” to enter the video template advanced setting interface, as shown in the figure below.

1. Select the channel to set.
2. Set whether to enable the ANR function of front-end IPC. If enabled, IPC will automatically start the local recording when the IPC is disconnected, and automatically upload the locally saved videos to the NVR when the IPC gets online again.
3. Select the pre-recording time from the “PreRecord” drop-down list.
4. Select the video delay time from the “PostRecord” drop-down list.
5. Set the time period and the video type within the time period. Click the “Time” option box to make it selected. Enter the start and end time of the time period into the time period input box. Select a video type from the “Record Type” drop-down list. Different video types can be specified for different time periods.
6. Copy the parameters of the current template to the channel and date.
7. Click “Apply” to save the configurations.

Holiday Plan:

You can configure holiday video plan of the year. When holiday plan is enabled, the video plan will be implemented first during holiday time.

1. Select “Main Menu -> Storage Setting -> Recording -> Holiday Plan” to enter the “Holiday Plan” interface, as shown in the figure below.

1. Click a holiday in the selected list, and click “Edit” or double click the

left mouse button to enter the “Holiday Setting” interface.

1. Check “Enable Holiday Plan” and choose the setting mode of the holiday “per Date”, “per Month” or “per Week”. Enter the start date and end date of the holiday. Click “OK” to save the configurations.
2. After enabling the holiday plan, you can select the holiday from the “Date” in “Advanced ” and set the corresponding video template for the holiday. Videos will be recorded according to this template for all enabled holiday plans.

J Note:

• All configurations by week take Sunday as the first day of the weekday, unless otherwise specified.

• • 1. Parameter

1. Select “Main Menu -> Storage Setting -> Parameter” to enter the video policy setting interface, as shown in the figure

below.

Not Enough Disk Capacity

0 Overwrite file

Delete Non-alarm Record

Stop Recording

Back

1. Select the processing method of the system when the disk space is insufficient, such as “Overwrite Files”, “Delete Non-alarm Record” or “Stop Recording”.
2. Click “Apply” to save the configurations.
   • 1. Diskgroup Allocation
3. Select “Main Menu -> Storage Setting -> Diskgroup Allocation” to enter the disk pack configuration interface, as shown in the figure below.

Recording

Reindex p0 Select All Disks

v* Select All Channels In This Page

001 002 003 004 005 006 007 008 009 010

011 012 013 014 015 016 017 018 019 020

| | | Back

1. Set disk group or quota.

Disk Group: Divides hard disks mounted on the NVR multiple disk packs. You can specify the disk pack where the video files are located for each channel.

Quota: Specifies the maximum disk space a channel’s video files can use. Different channels can be configured with different video space.

NO Note:

• Mode switching can come into effect only after the device is restarted.

Warning

A Recording mode changed needs reboot to take effect, reboot now?

Cancel

Confirm

1. Set the disk group.
2. Select “Disk Group” under “Mode Selection”.

Images Setting

Select All Channels In This Page

■ 03 ■ 04

■ 13 ■ 14

■ 05 ■ 06

■ 15 H16

■ 07 []08

■ 17 |18

■ 09 |10

■ 19 |20

Apply Back

1. Select disk group. There are disk groups 1 – 8 to choose from the drop-down box.
2. Select disks for a disk group. Sets which disks belong to the disk pack. Check “All Disks” to select all available disks. A disk cannot be assigned to more than one disk pack at the same time.
3. Select a channel for a disk group. Select which channels to record in the pack.
4. Click the “Apply” button to save the settings.

^Notes:

1. The storage bitrate of a single disk pack can be up to 100Mbps; otherwise there is a risk of video loss.
2. When ESATA is a non-backup disk, it appears in the All Disks box.
3. There are 20 channels in one disk pack for NVR by default. The rest can be done in the same manner.
4. Quota Configuration
5. Select “Quota” under “Mode Selection”.

Recording

| | | Back

1. Select the channel to set. Select the channel where you want to set the quota from the “Channel” drop-down box.
2. Set the video quota. Sets the maximum storage space that video files of the channel occupy, in GB. 0 indicates unlimited.
3. Set the image quota. Sets the maximum storage space for the image files of the channel, in GB. 0 indicates unlimited.
4. Save the settings. Click the “Apply” button to save your settings.
5. Quota mode is not recommended for devices with over 40

channels.

• • 1. Images Setting

1. Select “Main Menu -> Storage Setting -> Image Setting” to enter the snapshot setting interface, as shown in the figure below.

1. Select the target channel number for the snapshot setting

operation.

1. Set snapshot type: “Snapshot” and “Alert Snapshot”. When “Alert Snapshot” is selected for snapshot type, the snapshot setting interface is shown in the figure below.

1. Set snapshot mode: “Single Picture” and “Multiple Pictures”.
2. Set the time interval of snapshot, in seconds.
3. Choose whether to upload captured pictures via FTP. Click the “Upload To FTP” button to enter the FTP setting interface. For details about FTP settings, refer to the corresponding section.
4. Choose whether to upload the captured pictures via SNMP. Click the “Upload To Email” button to enter the Email setting interface. For details about settings, refer to the corresponding section. On this interface, Email Setting is unavailable for alarm snapshot.
5. The snapshot setting parameters of the current channel can be copied to the specified channel.
6. Click “Apply” to save the configurations.

ote:

• The system can snapshot at most 2000 pictures per channel within 24 hours. The snapshot count will be cleared after the system is restarted.

• • 1. Reindex

When HDD exception or video loss occurs, lost videos can be retrieved to the maximum extent by rebuilding the index.

1. Select “Main Menu -> Storage Setting -> Reindex” to enter the “Reindex” interface, as shown in the figure below.

Tia ndy

Recording

Parameter

E

Playback

a

Backup

A

Alert Ma…

■id

VCA

o H E S X

Cameras Storage … Alarm Se… System S… System …

Rebuilding a index may take some time and pause time lapse,are you sure to continue?

Images Setting

Diskgroup Allocation

Reindex

Apply Back

1. Click the “Continue” button to start the rebuild operation.
2. When rebuilding the index, users can exit the interface for other operations.

4.8 Playback

• • 1. Instant Playback

On the preview screen, play back the video file of the selected channel within 5 minutes.

In preview state, select the channel to played back by using the left

mouse button, and click the

button on the shortcut menu, and

enter the “Playback” interface, as shown in the figure above.

• • 1. Description of Playback Interface

Here, the composition and function modules of the playback interface are introduced.

To enter the menu playback interface: preview and use “Right-Click Menu-> Playback” to enter the playback interface, as shown in the figure below.

Description of playback control bar

• • 1. Normal Playback

Retrieve the corresponding video files by channel and date, and play video files in turn from the generated play bar that meets the criteria. The playback steps are as follows:

1 Select “Main Menu -> Playback” to enter the “Normal” interface, as shown in the figure below.

2_X Select the channel to play back and the calendar automatically displays the recordings of the month.

3_X Use your mouse to click the date you want to play back.

4_X The system automatically plays the video files that meets the criteria.

5_X Other playback operations.

• Use the “Full Screen” key in the upper right corner to enable full screen playback.
• If there is no operation for a period of time during playing, it will automatically enter the full-screen playing mode. You can operate the mouse or keyboard again to exit the full-screen.
• Use “Fast Forward” or “Slow Forward” key to fast or slowly play

back videos.

_]Note:

• Up to 16 channels can be played back at a time. The playback performance differs depending on the device model and video recording.

4.8.4 Event Playback

Query a video file in a certain time period by event type (port alarm, motion detection, video loss, video occlusion, intelligent analysis), and play the video from the generated list that meets the query criteria. The operation steps are as follows:

1. Enter the playback interface, and select “Event” for the playback mode.

2_S Select event type in the upper right corner of the playback screen.

3_S Select the channel to play back.

4_S Click the date you want to play back.

5_S The system automatically plays the video files that meet criteria.

Note:

• During event playback, the player will skip the time period without alarm video according to the alarm time period of the video.

4.8.5. Tag Playback

The video label function allows users to record the relevant personnel or on-site information at a certain time when the video is played back, so that users can retrieve the information at any time to search and locate the video.

Add/Manage Labels

1 Enter the video playback interface Click El to add the default label.

Click to enter a label name and add a custom label.

2_S Label management

Click

to enter the “File Management” -> “Label Management”

interface, as shown in the figure below, where you can view, edit, and

delete added labels.

Tag Playback

1 Enter the playback interface, select “Tag” for playback mode, and enter the “Tag” interface, as shown in the figure below.

2_S Select a channel.

3_S Enter the label keyword. If no keywords are entered, all labels within
the specified date of the selected channel are retrieved by default.

4_S Select a date.

5_X The playback progress bar shows a label marked with an inverted

green triangle. When the mouse cursor is moved over the position

marked by the inverted triangle, the label name information will be

displayed automatically, as shown in the figure below.

• Video playback begins with the value set in “Pre-Playback” before the time of adding labels, and ends with the value set in “Post-Playback” after the time of adding labels. When finished, the system automatically jump to the next label for playback.
• Playback Advance Time and Playback Delay Time can be set separately.

4.8.6 Smart Search Playback

Smart search playback refers to the intelligent analysis of video files. Options include “Perimeter Search”, “Tripwire Search” and “Face Detection”.

The operation steps are as follows:

1. Enter the playback interface and select “Smart Search” for the playback mode, as shown in the figure below.
2. . The play operation begins after the channel and date are selected.

in the lower left corner of the interface to enter the

3. Click

intelligent retrieval interface, as shown in the figure below.

button at the bottom of the interface and

4.

Click the

select the retrieval type.

1. Click

or _

figure below.

1. .8.6.1 Tripwire and Perimeter Search

button to enter the drawing interface of

intelligent playback and draw lines on the video, as shown in the

2.Click the

button to start searching. During the search process,

“VCA SEARCHING…” appears in the top left of the screen and the

progress bar will show the progress and results of the search.

1. .During the search process, the system automatically jumps to the search results to start playing.
2. . Click on another channel or other date during the search process will automatically stop searching. You can also click the Stop button or Exit button to manually stop searching or exit the intelligent search.

4.8.6.2 Face Detection

1.

Click

to enter the “Face Detection” interface of intelligent

playback, as shown in the figure below.

button to start searching. During the search process,

2.Click the

“VCA SEARCHING…” appears in the top left of the screen. At the same

time, the progress bar will display the search progress, and one the right side is the face detection search results.

3. Click on the Stop search during the search process will stop searching. When you click the search results on the right, the video will be positioned to the corresponding location.

4.8.7 Video Concent Playback

The video summary playback function is to superimpose multiple moving targets at different time points into the same background for simultaneous playback, which can shorten video time and greatly improve the efficiency of video playback. Before playing back video summary, make sure that the front end device connected to the selected channel supports and enables the intelligent analysis function.

The operation steps are as follows:

1. Enter the playback interface, and select “Video Concent” for the playback mode, as shown in the figure below.

Video Concent

00:00:00

0%

2. Select a channel, set the start and end times, click “Search”,

and play back the video summary video file, as shown in the

figure below.

3. Double-click the rectangular box stacked on the left side to

locate the time to play in the small window on the right, and

then play the video of 30s before and after the time point.

Notes:

• Stop and Pause options are available on the large screen on the left, and both the progress bar and percentage can be displayed but dragging over the progress bar is impossible.
• Stop and Pause options are available on the small screen on the right. And both the progress bar and percentage can be displayed, and dragging over the progress bar is possible. In addition, current files can be backed up.
• 4 decoding channels can be superimposed on the target simultaneously. The actual number of superimposing layers depends on the decoding ability. With the real-time playback screen of channel 1 as the background, the targets of other channels are superimposed on channel 1.
• The time period of each decoding channel is generally evenly distributed according to the time length of target information.
• Video summary playback is only available for some models.

4.8.8 Time-phased Playback

The time-phased playback function means that the recording time of a channel in a day is averaged to multiple screens for asynchronousplayback according to the number of split screens, which can effectively improve playback efficiency.

The operation steps are as follows: 1. Enter the playback interface and select “Time-phased Playback”, as

shown in the figure below.

2. Select the playback channel and set the number of split screens. Here,

4 split screens are taken as an example.

3. Select the date on the right side or click the Play button for time-phased playback.

• • 1. . Picture Playback

The picture playback function refers to the playback of the pictures stored in the hard disk, as shown in the figure below.

Notes:

• Users can define a play interval for play pictures automatically.
• You can also pause the playback and click on the left or right side

of a picture to display the previous or the next picture.

• • 1. External File Playback

The external file playback function refers to playback of video files stored in external storage media such as USB flash drive, mobile hard disk or CD-ROM.

The operation steps are as follows:

1. Enter the playback interface and select “External File “, as shown in the figure below.

Device type and file type are optional

1. Select “Refresh” to read external storage media.
2. Click the file to play to play back external video file, as shown in the figure below.

• Before playing back external files, make sure that USB flash drive or mobile hard disk or USB drive has been connected to the device.

• • 1. Log Management

Play the video file corresponding to the log information.

The operation steps are as follows: 1 Select “Main Menu -> System Maintenance -> Log Management” to

enter the “Log Management” interface, as shown in the figure below.

Information

Export Current Export All

Back

2_X Select “Channel” , “Type” , and “Start/End Time” , and click

“Search”.

3_X Double-click a log in the log list to enter the “Playback” interface, as

shown in the figure below.

Notes:

• The playback progress can be controlled by the playback time bar on the bottom.
• There shall be video files at the channel and time point corresponding to the selected log and these video files can be played.
  • 1. Playback Assist Function

Single-Frame Playback

During video playback, single-frame playback allows checking of the detail change of the screen.

On the playback interface, left-click O or □ or adjust the playback speed to “Single Frame”. Step forward one frame for each click on the □ button, and step back one frame for each click on the d button.

The single-frame playback interface is shown in the figure below.

Digital Zoom

The partial picture of the video is enlarged to the full screen display in the process of playback or playback pause.

The operation steps are as follows:

1. Enter the playback interface.
2. . Select the B button on the playback control bar to enter the digital

zoom interface.

1. .The drag bar on the top left or your mouse wheel can be used to

adjust the zoom factor.

4.Press and hold and drag the left mouse button to see different areas.

Snapshot

Snapshot in the process of video playback.

The operation steps are as follows:

1.Enter the playback interface.

2.Select a screen and click theEl button on the playback control bar.

nO Note:

• Images captured during playback need to be saved on a USB flash drive. When carrying out the snapshot operation, make sure the USB flash drive is correctly connected to the device.

Progress Bar Preview

On the playback interface, when playback mode is selected as regular playback, event playback, or label playback, and single screen is selected, the system will automatically display the time point and the images before and after the time point when your mouse slides over the play progress bar. The operation steps are as follows:

1. Select playback mode as one of the above and start playback.
2. Hover your mouse over a section of the progress bar that has video footage, and a preview image will appear, as shown in the figure below.
3. Click any of small screens, and then locate to the time point to play.

Notes:

• The progress bar preview operation is impossible when the decoding performance reaches the upper limit.
• The progress bar preview operation is impossible on the current channel when no video is available at the selected time point.
• No progress bar preview is available for non-single screen.

Quick Drag to Play

When playing on a single screen, you can quickly drag the progress bar. In this case, the progress bar will be dragged to play video quickly to facilitate viewing.

• 1. Backup

Backup allows backing up of video files in the system to the backup disk or USB storage device (USB, mobile hard disk, esata).

1. Select “Main Menu -> Backup” to enter the backup interface, as shown in the figure below.

1. Click “Video Snapshot” to visually display recordings of the specified date. After the date is selected, click “OK” to help the user select the start and end time of video querying according to the date. After returning to the interface in step 1, you can check it from “Start Date”, “Start Time”, “End Date”, and “End Time”.

Note:

• Image files do not support video snapshot.

1. After identifying the query conditions, if “Enable Backup Authentication” is checked, click on “Backup” or “Query Backup” button will display the authentication form. You need to conduct authentication first before proceeding to the next step.

code verification

Username

Password

Cancel

Confirm

1. After identifying the query conditions, click the “Backup” button. If the backup destination is a USB storage device, it will enter the backup interface where you can select the destination folder for backup. If the backup destination is a backup disk, then proceed to the backup operation directly.

1. After identifying the query conditions, click the “Query Backup” button for video file querying.

The video query results are presented in a list or a chart manner.

List:

To play the file, click the “Playback” icon or double-click the line where the file is located.

Click the “Lock” icon to lock and unlock the file.

Chart:

Click to select a certain screen to play the 10s video after the time

point. Double-click the preview image to play it back.

1. Select the video file to back up from the list or chart, and click the “Backup” button to enter the backup screen.
   1. . System Maintenance
      1. Information

System Information

1. Select “Main Menu -> System Maintenance -> Information -> System Information” to enter the system information interface, as shown in the figure below.

Tiandy

System Information Channel status Recording status Alert status Network State Disk status Online User

Manufacturer

Factory ID

Serial Number

Firmware Version

Hardware Version

UI Version

SDK Version

Web Version

Access Module

System Time

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Back

1. The manufacturer, serial number, kernel version, hardware version, SDK version, webpage version, UI version, and system time can be checked under System Info.

Channel Status

1. Select “Main Menu -> System Maintenance -> Information -> Channel

Status” to enter the channel status interface, as shown in the figure

below.

Back

Bandwidth Remain

1. Channel number, channel name, connection status, motion detection status, video occlusion status and video loss status can be checked under Channel Status.

Devices not supporting video occlusion alarm function will not

display the video occlusion column on the screen.

Record Status

1. Select “Main Menu -> System Maintenance -> Information -> Recording Status” to enter the record status interface, as shown in the figure below.

Tia ndy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

System Information Channel status Recording statu Alert status Network State Disk status Online User

5. Channel number, recording status, stream type, real-time frame rate/set frame rate, real-time bitrate/set bitrate, video resolution, video type, compression parameters, redundancy status can be checked under Record Status.

6_X When you click video template, video strategy and disk page setting, the HDD status can jump to the corresponding interface to view the device configuration status.

Alert Status

1. Select “Main Menu -> System Maintenance -> Information -> Alert

Status” to enter the alarm status interface, as shown in the figure below.

Information

System Information Channel status Recording status Alert status Network State Disk status Online User

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Back

1. Serial number, name, annunciator type, ON/OFF status, channel triggering of the local alarm and alarm host can be checked under Alarm Status.

Network State

1. Select “Main Menu -> System Maintenance -> Information -> Network State” to enter the network status interface, as shown in the figure below.

System Information Channel status Recording status Alert status Network State Disk status Online User

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Back

1. Network card-related network information can be checked under

Network Status.

Note:

• Devices not supporting dual network cards will not display the

network card 2 column on the screen.

Disk Status

1. Select “Main Menu -> System Maintenance -> Information -> Disk

Status” to enter the HDD status interface, as shown in the figure below.

1. HDD number, SMART detection status, size, idle, property, disk pack, total remaining capacity and total capacity of all hard disks can be checked under HDD status.

Online User

1. Select “Main Menu -> System Maintenance -> Information -> Online

User” to enter the online users interface, as shown in the figure below.

4.10.2 Log Management

1. Select “Main Menu -> System Maintenance -> Log Management” to

enter the log querying interface, as shown in the figure below.

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

E

Playback

a

Backup

Alert Ma…

iki

VCA

O H3 S

Cameras Storage … Alarm Se… System S…

*

| System

Channel All

Type All

Record Time

Type

Channel User

Start Time

End Time

Content

2020-03-13 j|| 00:00 ©

2020-03-13 H 23:59 ©] | Search

Play Details

1/1 page

Export Current Export All

Back

1. After selecting query conditions such as channel, type, start and end times, click “Query” button for log querying.
2. After logs are obtained, you can use the button to select the previous page or next page to view the logs, or input the number of pages. Click OK to jump to the page, select the log and click to check log details. Select alarm logs and click O to preview the video in the alarm time period.
3. Log export operation:
4. To export the current page: After querying the log, click “Export Current Page” to display the following form. Select the path and click “OK” to backup the log on the currently viewed page to the specified path.

Log export

Refresh

Remaining Space

1. To export all pages: Click “Export All Pages” to export all the logs that have been obtained. The backup path operation is the same as above.

4.10.3 Configuration

Configuration Export

1. Select “Main Menu -> System Maintenance -> Configuration -> Configuration Export” to enter the config export interface, as shown in the figure below. Performing the “Export” operation on configuration files of the device will facilitate timely backup of configuration file.

Information

Configuration Export Configuration Import Log Management

Configuration ._ . .

Export to U

Reset To Default

File name

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Export j | Back

1. Select Config Export and add the export file name and destination to export device configurations.

Configuration Import

1. Select “Main Menu -> System Maintenance -> Configuration -> Configuration Import” for import operation. If the same configuration is used for multiple devices, the “Import” operation will allow saving device configuration time.

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

E a sisi

Playback Backup Alert Ma… VCA

Configuration Export Configuration Import

Import file list

3.box uuu.box

D H

Cameras Storage …

B S X

Alarm Se… Systems… System…

Note:

1. The device will restart automatically after successful import.

4.10.4 Reset To Default

Reset To Default

1. Select “Main Menu -> System Maintenance -> Reset To Default ” to enter the restore defaults interface, as shown in the figure below.

ffll

Storage …

E

Alarm Se…

s

System S…

X

System …

Back

1. The users can select the module to restore defaults according to their own needs. Click the “Continue” button, and the selected module will be restored to default configurations.

nO Note:

• The device will restart automatically after restoring the defaults.

• • 1. Automatic Maintenance

1. Select “Main Menu -> System Maintenance -> Automatic Maintenance -> Device Maintenance” to enter the device maintenance setting interface, as shown in the figure below, where you can set the device name, number and automatic restart time.

Tiandy EaAiiiioiSfflsx

Playback Backup Alert Ma… VCA Cameras Storage … Alarm Se… System S… System …

Information

, _t Auto Reboot Each year xz IMonth x/I IDay 00:00

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Apply Back

• • 1. . System Upgrade

1. Select “Main Menu -> System Maintenance -> System Upgrade -> Cloud Upgrade” to enter the cloud upgrade interface, as shown in the figure below.

Information

Cloud Update Upgrade from local Upgrade from FTP

Log Management

Configuration _ . .

Current Version

Reset To Default _f

Latest Version Manual Detect

Automatic Mainta…

Release Date

System Upgrade

Automatically detect the NVR new version

Network Detect

Disk Detection

Click Manual Detection to check whether there is the latest version available. If there is a new version available, click Upgrade to upgrade to the new version.

1 Select “Main Menu -> System Maintenance -> System Upgrade -> Upgrade from local” to enter the local file upgrade interface, as shown in the figure below.

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

E a sisi

Playback Backup Alert Ma… VCA

Cloud Update Upgrade from local Upgrade from FTP

File Name

o H E S X

Cameras Storage… Alarm Se… Systems… System…

Files

Back

1. Click Browse to select the file you want to upgrade, and then upgrade it, as shown in the figure below.

3_X Select “Main Menu -> System Maintenance -> System Upgrade ->

Upgrade from FTP” to enter the FTP upgrade interface, as shown in

the figure below.

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

E

Playback

a

Backup

A

Alert Ma…

■id

VCA

D H

Cameras Storage …

Cloud Update Upgrade from local Upgrade from FTP

Server 192.168.001.001

Username

Password I Upgrade

E S

Alarm Se… System S…

X

System …

Note:

• After the upgrade is successful, the device will automatically restart and the new version comes into effect after restart.
• If it is suggested that the upgrade fails or the equipment cannot operate normally after restart, please contact your vendor for solutions.
  • 1. Network Detect

Network Detect

1. Select “Main Menu -> System Maintenance -> Network Detect -> Packet Backup” to enter the packet snapshot backup interface, as shown in the figure below.

| Status Detect j

USB1-1 | Refresh |

Packet Backup

Information

Packet Backup Network Flow Network Resources Statistics Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Network Card Selection

Destination Address

Current Network Card

Device

Network cardl

Test

©

Disk Detection

Back

1. In the network testing field, enter the destination address to test whether the address can be pinged through.
2. Click the “Packet Snapshot Backup” button to capture the current network card and save it to the specified storage medium.
3. Click the “Status Detection” button to check whether the gateway and DNS of the current network card are accessible.
4. Select the “Main Menu -> System Maintenance -> Network Detect ->Network Flow” interface to view and display real-time network data, as shown in the figure below.

Tia ndy

E

Playback

a

Backup

O H3 S

Cameras Storage … Alarm Se… System S…

X

System …

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

Disk Detection

Packet Backup Network Flow Network Resources Statistics

Network Flow Network cardl

Uploading Speed

Downloading Speed

Total uploading flow

Total downloading flow

Refresh Back

1. Select the “Main Menu -> System Maintenance -> Network Detect -> Network Resource Statistics” interface to check the usage of network resources, as shown in the figure below.

Tiandy

Information

Log Management

Configuration

Reset To Default

Automatic Mainta…

System Upgrade

Network Detect

E

Playback

a

Backup

zto

Alert Ma…

■id

VCA

Packet Backup Network Flow Network Resources Statistics

Disk Detection

D H

Cameras Storage …

E S

Alarm Se… System S…

X

System …

Refresh Back

• • 1. . Disk Detection

S.M.A.R.T.

1. Select “Main Menu -> System Maintenance -> Disk Detection ->

S.M.A.R.T.” to enter the SMART setting interface.

1. Select the disk to detect and check “Enable S.M.A.R.T Detection” to enable the S.M.A.R.T detection function of the disk. S.M.A.R.T detection information is displayed in the corresponding interface.
2. When “Do not use the HDD when it fails self-assessment”, do not use the HDD if there is any problem with the self-assessment after the S.M.A.R.T test.

Bad Track Detection

1. Select “Main Menu -> System Maintenance -> Disk Detection -> Bad

Track Detection” to enter the bad track detection interface.

1. Select the hard disk and detection method and click the Detection button to enter the detection status.

1. Click Pause to suspend the bad track detection; Click Restore to resume the bad track detection;
2. Click Cancel to cancel the bad track detection;
3. Click the Error Message button to check the bad track of the hard disk.

Note:

• The Error Message button is available only if the number of errors on the hard disk is greater than 0.
• When the number of errors on the hard disk is 100, bad trace

detection stops.

“means the corresponding area of the hard disk is in good

condition,”

“means the corresponding area of the hard disk is

damaged,”

“means the corresponding area of the hard disk is

shielded.

• 1. System Setting

For unified management of device attributes in the system.

• • 1. General Setting

Basic Setting

1. Select “Main Menu -> System Setting -> General Setting -> Basic Setting” to enter the basic setting interface, as shown in the figure below, where you can set the local output display parameters of the device.

Tiandy

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

E

Playback

a

Backup

A

Alert Ma…

Basic Setting Time Setting Plan Setting

■id

VCA

D H E

Cameras Storage … Alarm Se…

s

System S…

X

System …

Language English

Screensaver Time 5 Mins

Device Name DVRS

Device ID 18

Mouse Cursor Speed — + 80

Enable Startup Guide

Hide icon of video, alarm and facial recognition on preview interface

I I Send warning if equipment decoding performance reaches up limit

I | Allow access of third-party IPCs H265

Enable screen resolution adaptive reminder

Hidden target detection face attribute

Back

Note:

• Language: Selects the system language.

• Screensaver Time: Selects the interface timeout time.
• Enable Startup Guided: Selects whether to enable boot wizard settings.
• Buzzer when pressing button: Turns on the buzzer.
• Hide icon of video, alarm and facial recognition on preview interface: Selects whether to display video, alarm, face recognition icons on the preview interface.
• Send warning if equipment decording performance reaches up llimit: Selects whether to display the prompt message when the decoding performance reaches the upper limit.
• Mouse Cursor speed: Selects the mouse movement speed, 0-100 adjustable.

Time Setting

1. Select “Main Menu -> System Setting -> General Setting -> Time Setting” to enter the time setting interface, as shown in the figure below, where you can set system time, time zone, and NTP timing parameters.

General Setting

Back

Plan Setting

1. Select “Main Menu -> System Setting -> General Setting -> Plan Setting” to enter the preplan setting interface, as shown in the figure below. When an alarm situation occurs, the linkage preplan is displayed on the preview interface, and the on-duty personnel shall deal with it according to the preplan, such as alarming, notification, asking for helps, etc.
2. Click the preplan name or preplan content to directly edit them, as shown in the figure below.

4.11.2 Network Setting

Network Card

1. Select “Main Menu -> System Setting -> Network Setting -> Network

Card” to enter the network card setting interface.

1. Choose to automatically obtain or manually set the IP address. If auto obtain is selected, the system will automatically obtain the IP address from the DHCP in the network.
2. When selecting “Automatically obtain IPv4 address”, information including device’s IP address, subnet mask, and gateway should be specified.
3. Aggregated options. There are three modes in the drop-down box: multiple access, load balance and redundancy:

• Network multiple access: In this mode, Network Card 1 and Network Card 2 work independently.
• Load balance: In this mode, the network load is evenly shared by two network cards.
• Network redundancy: In this mode, one network card works and the other is in standby mode. Once the working network card fails, the standby one will be immediately started to complete the seamless connection of network switching.

1. If multiple access mode is enabled, the configuration method of network card 2 is the same as that of network card 1.
2. Click the “Apply” button to make the settings effective.

Notes:

• This interface is displayed only for devices with dual network cards, and aggregated options are unavailable for devices without dual network cards.
• Once the aggregation mode is set, the network parameters of network card 2 will be automatically filled in, with no need of user intervention.

PSE Network Card

Note:

• PSE series NVR models support PSE network card settings. This setting is unavailable for other models.

1. Select “Main Menu -> System Setting -> Network Setting -> Network Card” to enter the network card setting interface and select the PSE network card.

I | Automatically obtain IPv4 address

E

Playback

a

Backup

Alert Ma…

iili D H E

VCA Cameras Storage … Alarm Se…

s

System S…

X

System …

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Network card PPPOE Black and white name list DDNS FTP Email

SIP UPNP Web Service

Back

1. After setting the network address, the network address of the plug&play camera will be automatically set to the address of the network segment.

Note:

• This interface will not be displayed for non-PSE devices.

PPPOE

1. Select “Main Menu -> System Setting -> Network Setting -> PPPOE” to enter the PPPOE setting interface.

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Network card PPPOE Black and white name list DDNS FTP Email

SIP UPNP Web Service

Connect Back

1. Set whether to dial automatically on startup.
2. Enter the account and password of PPPOE dial.
3. Click the “Connect” button to immediately start the PPPOE dial operation.
4. Click “Apply” button to save the setting of PPPOE dial into the system. If the “Auto Dial on Startup” is selected, the system will automatically dial in the next startup.

NO Notes:

• This interface is not displayed for devices not supporting PPPOE.
• If you cannot dial properly due to network interruption or change of the modem, please manually click the “Disconnect” button and then try again.

Black and White Name List

1. Select “Main Menu -> System Setting -> Network Setting -> Black and

White Name List” to enter the black and white list setting interface.

2. Choose the way how IP right is used: “Disable”, “Whitelist” or

“Blacklist”.

1. Enter the IP address that needs to be disabled or enabled in the IP address input box.
2. Click the “Add” button to add the IP address to the list.
3. Click “Apply” to save the configurations.

DDNS

1, Select “Main Menu -> System Setting -> Network Setting

->DDNS” to enter the DDNS setting interface.

Preview Setting

Enable

Disk Management

Server Domain

Error Management

DDNS Domain

User Management

DDNS ID

Other Setting

DDNS Password

Back

1. Set whether to enable the DDNS service.
2. Enter the device domain name.
3. Enter the domain name or IP address of the DDNS server.
4. Enter the login account and password of the DDNS server.
5. Click “Apply” button to save the configurations.

FTP

1. Select “Main Menu -> System Setting -> Network Setting -> FTP” to enter the FTP setting interface.

Tia ndy E 3 A iia a

Playback Backup Alert Ma… VCA Cameras

H E

Storage … Alarm Se…

s

System S…

X

System …

Black and white name list DDNS FTP

192.168.1.1

21

Email SIP UPNP Web Service

Back

1. Enter the server address, port number, account and password of the FTP server.
2. Click “Apply” button to save the configurations.

Email

1. Select “Main Menu -> System Setting -> Network Settings ->Email” to enter the Email setting interface.

1. Enter the server address, port number, account, password, encryption mode, recipient address and subject of the Email server.
2. Click “Apply” button to save the set parameters.

SIP

1. Select “Main Menu -> System Setting -> Network Setting -> SIP” to enter the SIP interface.

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Network card PPPOE Black and white name list DDNS FTP Email SIP UPNP Web Service

Address 1192.168.3 .200 Port ,5060 (1~65535)

Server ID 34020000002000000001 Device ID 34020000001110000011

User Name Admin Password ********

Heartbeat Inte… 60 Heart Rate 3

RegValidity 100 ] (l~2000000000)

Select Channel [01]Channel 1 Channel ID 987654321021111112

Alarm Input Remote Alarm Input 1 v Alarm Input No. 987654321021111112

Auto Filling Set j j Back

1. Enter address, server ID, account, heartbeat interval, term of validity, port, device ID, password, heartbeat rate, channel selection, channel number, alarm input and alarm input number.
2. Click “Apply” button to save the set parameters.
3. Click the “Auto Fill” button, and the channel number and alarm input number of the current channel will be incremented by one in turn.

UPNP

1. Select “Main Menu -> System Setting -> Network Setting -> UPNP” to enter the UPNP interface.

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

E

Playback

a

Backup

Alert Ma…

iili D H E

VCA Cameras Storage … Alarm Se…

s

System S…

X

System …

Back

1. Check the “Enable” option to enable “Mapping Type” check box.
2. When “Mapping Type” is selected as “Auto”, the default external port is used for corresponding services; when “Manual” is selected, the external port can be edited and then used for corresponding services. HTTP port and RTSP external port support 1-65535, and external ports for service ports support 1-65534.
3. Click the “Save” button to save the settings.

Network Services 1. Select “Main Menu -> System Setting -> Network Setting -> Network

Service” to enter the network service interface.

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Network card PPPOE Black and white name list DDNS FTP Email

SIP UPNP Web Service

FTP Port 21

HTTP Port 80

□ Enable SNMP

RTSP

RTSP Port 554

rtsp://<username>:<password>@<ip>:<port>/<channel>/<stream>

channel:channel,l to N;stream:Stream type,Main stream 1,Sub-stream 2,third …

Sample:rtsp://admin:admin@l 92.168.1.3:554/1/I

v Start the intranet for searching

Back

1. The FTP and HTTP ports of the device can be modified on this interface, where you can also set whether SNMP service is enabled or not.
2. Check the “Enable Intranet search” option to search devices in

different segments under the same route.

4.11.3 Disk Management

Basic Configuration

1. Select “Main Menu -> System Setting -> Disk Management -> Basic Configuration” to enter the basic setting interface. When the device is connected to two or more disks and configured as the same disk pack, the edit column in the list displays Z. Click Z to modify the purpose of the disk, including read-write, backup, redundancy, and read-only.

General Setting

, „ . Basic Configuration NFS Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

Device Size Used Free Sleep Attribute Disk Group Edit

| □ SATAI 9.04T |6.54T |2.50T |N R/W |1 | —

| □ USB1 7.23G 1.13G 6.10G N Backup — –

2.50T/9.04T(Balance Capacity/Total Capacity)

| [ Disk recovery j [ Initialization

1. The interface can display the total remaining capacity and total capacity of the current HDD and virtual disk.
2. Hot-swap. Select a disk from the disk list and click the “Hot-swap” button. The system will display “Hot-swap will lead to the offline of the disk, which can only be online by restarting the device or plugging the disk.”

Note:

• The hot plug button is disabled for devices that do not support hot plug function.

1. HDD detection. Sets whether all disks are detected when the device is powered off and restarted, and whether corrupted disks are fixed. Click the “Disk Detection” button to display the disk detection form, as shown in the figure below.

Disk recovery

Device will detect all disks after power off reboot.

Repair damaged disks

Confirm

Cancel

1. Initialization: Initializes the selected disk, and an initialization format can be selected for the USB flash drive.

Do

Note:

Disk initialization

Caution: Disk initializing will erase all data and take up big part of the system capacity, please close other applications, continue?

Back

• The file system is not displayed for devices that does not support

the initialization format selection for the USB flash drive.

NFS Setting

1. Select “Main Menu -> System Setting -> Disk Management -> NFS

Setting” to enter the NFS setting interface.

General Setting

, _ Basic Configuration NFS Setting

Network Setting

Other Setting

Back

1. Set the IP address (domain name) and directory of the “NFS” service.
2. Click “Apply” to save the configurations.

4.11.4 Array Management

TC-NR2020M7-E8, TC-NR2040M7-E8, TC-NR2080M7-E8,

TC-NR2080M7-E16, TC-NR2160M7-E16, TC-NR2020M7-S,

TC-NR2040M7-S8 and TC-NR2080M7-S8 support disk array. Disk array shall be set before being used.

Physical Disk

1. Select “Main Menu -> System Settings -> Array Management -> Physical Disk” to enter the physical disk interface, where the basic information of all physical disks of the current device is displayed, including capacity, related array, disk type, disk status and disk model.

Physical Disk Array

Disk No. Capacity Array Type Status Model

General Setting

Network Setting

Preview Setting

Disk Management

Array Management

Hot-spare Setting

Error Management

User Management

Other Setting

Array Name

Back

Enable Array

1. Enable array. Check “Enable Array” and the operation will take effect after reboot.
2. One-key config. After entering “Array Name”, click the One-key Config button, and the device will automatically create an array.
3. Disk setting. After selecting a disk, click the “Disk Setting” button to set the disk as “Idle Disk”, “Array Hot Standby Disk” or “Global Hot Standby Disk”.

Notes:

• Rules for creating arrays with One-key Config: The system first creates a global hot standby disk and then creates up to 3 RAID5 arrays based on the number of remaining disks. At least three hard disks are required to create a RAID5 array and up to 8 disks are supported; If there are less than 3 disks left, set the remaining disks as idle disks.
• The device supports only one global hot standby disk.

Array

1. Select “Main Menu -> System Settings -> Array Management -> Array” to enter the array interface.

1. Create an array. Click the “Create Array” button to enter the Create Array interface, as shown in the figure below. To create an array, you must specify a array name, array type, physical disk that makes up the array, and the hot standby disk number. When all the information is set, click the OK button to start creating the array.

Notes:

• Array hot backup disks are not supported for JBOD and RaidO.
• Each array supports only one array hot standby disk.

1. Rebuild array. When an array is “Degraded”, the array can be rebuilt. Select the disk number to be substituted into the array and click the OK button to begin rebuilding.

5, Delete array. Select the array to delete from the array list and click the

“Delete” button to delete the selected array from the system.

4.11.5 Hot-spare Setting

Enable the hot standby system (Note: The hot standby function is unavailable for 4- and 8-channel NVR and PSE series NVR). When a device in the hot standby system fails, the system will automatically switch to the hot standby unit which will work to ensure the continuity of video recording.

A hot standby system consists of several active units and hot standby units. An active unit can be set with up to 16 hot standby units. When the hot standby unit detects that the active unit is disconnected, the hot standby unit will actively connect to the front IPC connected to the active unit and start recording. When the hot standby unit detects that the active unit is connected, it will actively disconnect from the front IPC and upload the previous backup video to the active unit.

Active Unit Setting

1. Select “System Settings -> Hot-spare Setting” from the Main Menu to enter the hot standby setting interface.

2. Select the Normal working mode.

1. Check Enable Hot Standby, set the IP address of the hot standby unit, and click “Add”; or select the IP to delete and click “Delete”.
2. After the specified hot standby unit is set and connected to the system successfully, the working status will be updated to “Connected Successfully”; When the hot standby unit actively uploads the backup video files, the working status is shown as “Sync Now”, and the synchronization progress bar shows the synchronization percentage.

Hot Standby Unit Setting

1. Select “System Settings -> Hot-spare Setting ” from the Main Menu to enter the hot standby setting interface.
2. Select the Hot Standby mode.

1. Click the “Apply” button, and the system prompts that the device needs to be restarted to make the setting effective.
2. When the device restarts and enters the hot standby working mode, the main interface of the system will change accordingly, and only hot standby setting, video setting, system setting, user management and shutdown options are available.
3. Select “System Setting -> Hot-spare Setting ” from the Main Menu to enter the hot standby setting interface.

Hot-spa re Setting

Tiandy ® I s @ *

Hot-spar… Storage… Systems… System… 0 Q

Operation Mode Hot-spare Mode

1. Click the “Refresh” button to display active units with hot standby function enabled in the active unit list. Select the active unit to set hot standby mode.
2. Click the “Add” button, and the system will prompt you to enter the login username and password of this active unit. After verification, the IP and connection status of the active unit will be displayed in the active unit status list. If the password is wrong, the active unit status list will also show the IP of the active unit, but the status of the hot standby unit will be shown as “Connection failed”.
3. Click “Apply” to save the configurations.
4. On the hot standby configuration interface of the hot standby unit, select “Normal mode” to switch the hot standby unit back to the active unit.

otes:

• After the hot standby unit is changed to the active unit, the defaults should be restored manually.
• The system time of the active unit shall be the same as that of the hot standby unit.

4.11.6 Error Management

Network error

1. Select “Main Menu -> System Setting -> Error Management -> Network error” to enter the network exception setting interface, as shown in the figure below.

1. If exceptions are checked, the corresponding linkage actions of the system, including screen display, voice prompt and upload center, can be checked when these exceptions occur.

Storage error 1. Select “Main Menu -> System Setting -> Error Management -> Storage error” to enter the storage exception setting interface, as shown in the figure below.

1, If exceptions are checked, the corresponding linkage actions of the system, including screen display, voice prompt and upload center, can be checked when these exceptions occur.

4.11.7 User Management

Add User

1. Select “Main Menu -> System Setting -> User Management” to enter the user management interface, as shown in the figure below:

Tiandy

General Setting

Network Setting

Preview Setting

Disk Management

Error Management

User Management

Other Setting

E a sisi

Playback Backup Alert Ma… VCA

User List

D H E

Cameras Storage … Alarm Se…

s

System S…

X

System …

Username Group Permission Edit Delete

Admin Administrator /’

Default Default user

Add User Back

Note:

• The Default user is added. The Default user is active after logoff. Only local preview right can be configured for this user.

1. Click “Add User” to enter the “Add User” interface, where you can set the user group, account, password, etc., as shown in the figure below:

Notes:

• After a user is successfully added, the information about the added user is displayed in the Basic Config -> User List.
• Up to 16 users can be added.
• There are three user groups in the system: “Default users”, “Normal users”, and “Administrator”. The default permissions for each user group are as follows:

Default users: browse videos

Normal users: browse videos

Administrator: browse videos + device control + parameter setting

+ user management

User Permission Management

1. Click the in the user list to display the user permission editing form,

as shown in the figure below:

2. Descriptions of permissions:

1. Local permissions: i.e. local operation permissions, including manual alarm clearing, shutdown/restart, log search, alarm setting, channel management, parameter setting, system setting and user management.
2. Remote permissions: i.e. operation permission on a remote client, including manual alarm clearing, shutdown/restart, voice intercom, log search, alarm setting, channel management, parameter setting, system setting and user management.
3. Channel permissions: Local preview, remote preview, local playback/snapshot browsing, remote playback/snapshot browsing, local PTZ control, and remote PTZ control.

3. Descriptions of channel permissions:

If the current user does not have the local preview permission for a channel, the channel will be unchecked (channel 4 as shown in the figure below). If the user has the local preview permission for the channel, the channel will be checked.

Edit User

1. Click / in the user list to display the edit user form, as shown in the

figure below:

Note:

• Pattern unlocking and security problems are only available for admin user; The original password shall be entered to edit the admin user and click “OK”.

1. Pattern Unlocking

1. After checking Enable Pattern Unlocking, the form as below will appear. The unlocking pattern can be correctly set only when a pattern composed of the same 4 points or more is drawn twice as instructed.
2. Pattern unlocking is only available for the admin user.
3. Pattern unlocking is not enabled by default on startup. After setting successfully, you can click pattern setting to modify the pattern.
4. Security Problems
5. Set security problems: After the admin user logs in, edit the user, and click the “Set Security Problems” button to enter the security problems setting interface, as shown in the figure below.

Users can set 2 security problems. If custom problems are selected,

the problems shall not be left empty.

1. Security verification: In case that security verification is set, when the admin user logs in with his password, he can click the “Forget Password” button to change the password, as shown in the figure below:

Click the “Forget Password” button to enter the security verification

interface, as shown in the figure below:

Email:

1. Download the mobile APP to enter the password retrieval interface. (For the mobile APP download website, see Section 4.15 Mobile Monitoring “Mobile APP”)
2. Scan the QR code on the left (the picture is for reference only).
3. After scanning the QR code, the Email you leave will receive the security code.

4) Enter the security code to reset the new password.

Security problems:

1) After entering the correct security answer and the new password, click the “Next” button.

2)Change your password.

3) If no new password is entered, the original password will not be changed after the security answer is verified.

(3) Delete security problems: In case that security problems are set, , clicking the “Security problems” button will enter the security problems setting interface. In this case, no security problem can be set. Instead, the original security problems shall be deleted. You can click the “Delete” button to delete the original security problems, as shown in the figure below:

Device Lock

The device lock interface as shown in the figure below will appear after password unlocking fails for 5 times. The lock time will be 5 minutes.

It is locked

Lock the remaining time 4:55

Confirm

4.11.8 Other Setting

Video Encryption

1. Select “Main Menu -> System Setting -> Other Setting -> Video Encryption” to enter the video encryption interface, as shown in the figure below.

General Setting

, _ Video Encryption Type Management

Network Setting

Preview Setting _T r. j

Input Password

Disk Management

Confirm Password

Error Management

User Management

Other Setting

Apply Back

Type Management 1. Select “Main Menu -> System Settings -> Other Settings -> Type Management” to enter the type management interface, as shown in the figure below, where you can set the video type name.

General Setting

, „ . Video Encryption Type Management

Network Setting

4.12 Alarm Setting

• • 1. Alarm Input

By setting alarm inputs, when an alarm occurs in the local NVR, users can be prompted, or perform video recording, etc.

1. Select “Main Menu -> Alarm Setting -> Alarm Input” to enter the alarm input setting interface, as shown in the figure below.

Wed

Thu

Sat

Sun

Copy

Back

Copy To Port All

1. Select the input port number to set. On the interface, users can set local and host alarm input port numbers.
2. Set the input port alias. Users can set a custom name for the current input port.
3. Choose the annuciator type.

_]Notes:

• Open alarm: On when the alarm input port is open for the local NVR.
• Closed alarm: On when the alarm input port is closed for the local NVR.

1. Check “Enable” to set the alarm input arming time.
2. Enter “Activation” to set alarm linkage.
3. Options include sound prompt, linkage Email, linkage video, linkage output, linkage snapshot, linkage PTZ, linkage text preplan, linkage single screen.
4. After setting, parameters of other alarm input ports can be copied.
5. Click “Apply” to save the setting parameters.
   • 1. Alarm Output
6. Select “Main Menu -> Alarm Setting -> Alarm Output” to enter the alarm output setting interface, as shown in the figure below.

Alarm Input

Copy To Port All Whole W Copy

| | | Back

1. Select the output port number to set. On the interface, users can set the local and host alarm output port numbers.
2. Set the output port alias. Users can set a custom name for the current output port.
3. Choose the annuciator type. The type must meet the requirements of the input signal of the external device on the alarm output port.

NO Notes:

• Open alarm: Under normal circumstances, the alarm output port is closed. When there is an alarm in the system and the linked output port acts, the alarm output port is open.
• Closed alarm: Under normal circumstances, the alarm output port is open. When there is an alarm in the system and the linked output port acts, the alarm output port is closed.

1. Set signal delay time. The signal delay of the alarm output port can be set according to the actual needs.
2. Set alarm output arming time. The arming date is used in conjunction with the time period.
3. Copy to port. After setting, the parameters of other alarm output ports can be copied.
4. Click “Apply” to save the setting parameters.
   • 1. Alarm Host

The alarm host is added to expand alarm I/O ports on the basis of the local alarm I/O ports. If both network alarm host and serial alarm host are added, the port number of the network alarm host is smaller than that of the serial alarm host.

Network Alarm Host

1. Select “Main Menu -> Alarm Setting -> Alarm Host -> Network Alarm Host” to enter the network alarm host setting interface, as shown in the figure below.

Tia ndy

Alarm Input

Alarm Output

Alarm Host

Manual Alarm

Clear Alarm

Network Alarm Host

Alarm Server

I | Enable

IP Address

Port

Alarm Input

Alarm Output

Back

1. Set a number for the network alarm host.
2. Check “Enable” to enable the network alarm host.
3. Set the IP address of the network alarm host.
4. Set the communication port of the network alarm host, which is limited to 18803. Only when the alarm host port number in the network alarm host IE is also set to 18803 can communication be normal.
5. Set the number of alarm input ports of the network alarm host.
6. Set the number of alarm output ports of the network alarm host.

Serial Port Alarm Host

1. Select “Main Menu -> Alarm Setting -> Alarm Host -> Serial Alarm Host” to enter the serial alarm host setting interface, as shown in the figure below.

2. Set a number for the serial alarm host.

1. Check “Enable” to enable serial alarm host.
2. Set the serial port number for the serial alarm host.
3. Set the address for the serial alarm host.
4. Set the number of alarm input ports of the serial alarm host.
5. Set the number of alarm output ports of the serial alarm host.
   • 1. Manual Alarm
6. Select “Main Menu -> Alarm Setting -> Manual Alarm” to enter the manual alarm setting interface, as shown in the figure below.

(g g] sisi

Tia ndy

Alarm Input

Alarm Output

Alarm Host

Manual Alarm

Clear Alarm

Playback Backup Alert Ma… VCA

Channel Alarm Output Port Alarm Name Activate

o H E S X

Cameras Storage … Alarm Se… System S… System …

| | 01 01 Local Alarm Output 1

Refresh Activate Clear

Back

1. Select an alarm output port and click the “Trigger” or “Clear” for triggering or clearing. The alarm output port status bar shows the current status of the port. Click “Trigger All” or “Clear All” to trigger or clear all alarm output ports in the list. Click the “Refresh” button to get current property and status of the alarm output port.
   • 1. Clear Alarm
2. Select “Main Menu -> Alarm Setting -> Clear Alarm” to enter the manual clearing setting interface, as shown in the figure below.