Hikvision NVR 5.0 Professional Installation Guide

Hardware Installation

Software Configuration

Additional Resources

Important Note: The provided steps serve as a general guideline. Specific configurations might differ based on your NVR model. Always refer to the official user manual for detailed instructions and advanced functionalities.

Setting up a Hikvision NVR (Network Video Recorder) involves several steps, including hardware setup, network configuration, and camera configuration. Here’s a detailed guide to help you set up your Hikvision NVR 5.0:

1. Hardware Setup

Step 1: Unbox and Connect Components

Step 2: Connect the NVR to a Monitor

Step 3: Connect the NVR to the Network

Step 4: Connect Cameras to the NVR

Step 5: Power Up the NVR

2. Initial Configuration

Step 1: Boot Up and Log In

Step 2: Set Date and Time

Step 3: Network Settings

3. Adding Cameras

Step 1: Detect and Add Cameras

Step 2: Configure Camera Settings

4. Recording Settings

Step 1: Set Up Recording Schedule

Step 2: Configure Storage Settings

5. Remote Access Setup

Step 1: Enable Hik-Connect

Step 2: Port Forwarding (if necessary)

Step 3: Mobile App Setup

6. Final Steps

Step 1: Test the System

Step 2: Backup Settings

Troubleshooting Tips

This guide should help you set up your Hikvision NVR 5.0 system. For more detailed instructions, refer to the user manual or the Hikvision support website.

.

Get Started with Verkada Intercom Set up and connect your Verkada intercoms Updated over a week ago

Required. You need Org Admin and/or Site Admin permissions for your Verkada Command organization to complete these actions.

What you need

Create a site

Sites are the logical way of grouping and managing devices within your Command organization. Site-level permissions make managing and viewing your devices easier. See Manage Your Sites and Subsites for more information on site creation and management.

Add an intercom

At least one intercom needs to be added to Command before you can see the Intercom tab in the All Products menu. Intercoms can be added to Command from the Devices page. See Add an Intercom to Your Site for more information.

Connect a door

You can pair an existing access-controlled door or wire a door to the intercom that can be unlocked by an intercom receiver. See Configure a TD52 and Wire a TD52 Video Intercom for more information.

Configure receivers

Receivers allow you to answer calls from an intercom and unlock any associated doors. See Add and Configure Receivers in Intercom for more information.

Licensing

Every intercom you manage in Command will need a license. Verkada licensing is applied for each Command organization, and the licenses co-term to a single expiration date. Your licenses may have been automatically added if you claimed your devices via order number. Otherwise, manually add the licenses from the Admin page. See Manage Your Licenses for more information on adding and managing licenses.

Connect your intercom

Recommendation. While Verkada intercoms are considered low-voltage devices that do not require a certified electrician to install, we strongly recommend you work with a system integrator or other professional for installation.

Please refer to the intercom setup guide for instructions on mounting and wiring the door port.

Power and network

Verkada intercoms use Power over Ethernet (PoE) for power and communication over the LAN. In most cases, intercoms will connect directly to an 802.3af PoE standard switch. PoE injectors can be used when a PoE switch is not available. See the intercom’s datasheet for more information.

Check network settings

Verkada intercoms are designed to be plug-and-play. However, if your environment includes a firewall with custom rules and policies, you may need to make some configuration changes to get your access controllers connected to the cloud. See Intercom Network Settings for more information.

Roles and Permissions for Intercom

Roles and Permissions for Intercom

Learn more about Verkada Intercom roles and permissions

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Intercom.

Verkada intercoms setup guide v1

Verkada Intercom permissions determine who can receive calls, view intercom video, and unlock intercom doors. Intercom permissions depend on your site-level permissions, and whether you’re configured as a Receiver.

At a high level, these are the permissions granted to each level of Intercom devices:

Site-level roles

Receiver

Required. You must be configured as a receiver to receive calls.

If you’re a Verkada Intercom Receiver, you have the baseline receiver permissions (as shown above). These baseline Receiver permissions combine with site-level permissions to determine overall intercom permissions within a certain site.

For example, if you’re a Receiver for a particular intercom, and a Site Viewer, you get all the Receiver permissions, in addition to the ability to view historical video and events.

Note: Receivers, such as Desk Stations and Session Initiation Protocol (SIP) phones are not tied to a Verkada Command user. This means that the user can only get Receiver permissions, regardless of the user’s site-level permissions.

Regardless of their site-level permissions, a Receiver can:

Live-View Only

Site Viewer

Site Admin

.

Verify a user’s eligibility to receive Verkada Pass calls

.

Set Org Admin permissions

Revoke Org Admin permissions

.

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Intercom Network Settings

Intercom Network Settings

Learn about the required network settings for Verkada Intercoms

Updated over a week ago

This article outlines the required network settings that your Verkada Intercom needs to communicate with Verkada Command. For more information on the required network settings for other Verkada product lines see Required Network Settings.

Note: Verkada devices are incompatible with LANs that require proxy servers or Secure Socket Layer (SSL)/Transport Layer Security (TLS) inspection. If either is in use, a bypass for all Verkada devices must be implemented for Verkada devices to communicate with Verkada Command.

Status LED

A flashing blue status LED on the top of the intercom indicates the intercom is not communicating with Command. If you see this behavior, check that the network is set up correctly with the intercom’s requirements. If the problem persists, contact Verkada Support.

IP address

Intercoms must be assigned an IPv4 address to communicate on the LAN and to Verkada Command. Intercoms use Dynamic Host Configuration Protocol (DHCP) and User Datagram Protocol (UDP) to obtain their IP addresses and network configurations.

If you require your intercom to have a specific IP address, create a DHCP reservation using the device’s Media Access Control (MAC) address (found on the device’s label).

Domain Name System

Intercoms use the DNS server to resolve Verkada’s fully qualified domain names (FQDN) to IP addresses to communicate with them. Your DHCP server tells the intercom where the DNS server is on the network and the intercom communicates using UDP port 53.

Note: DNS over HTTPS (DoH) is currently not supported.

Power

Intercoms are powered through Power over Ethernet (PoE). This means the network switch needs to provide power to the intercom, or a PoE injector needs to be utilized. For specifics on power requirements, see the Intercom datasheet.

Firewall settings

Intercoms require access to many endpoints to ensure they can communicate with Command and all features will be accessible. Many customers may want to allow the intercoms to communicate with the general required endpoints.

These are the general domains to allow, applicable for all organization-regions:

Region: United States

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Region: Europe

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Mount a TD52

Mount a TD52

Learn how to mount the Verkada TD52 Video Intercom

Updated over a week ago

Use this article to learn how to mount a Verkada Intercom (TD52). Once you complete the mounting, you can connect the TD52 to the network.

Before you begin

You can mount the TD52 using a flush mount or using a mounting bracket. We recommend that you verify the contents of your box and make sure you have the tools you need

Contents of your box

Tools you need

Choose your mounting option

Whichever mounting option you choose, you should remove the front cover of the TD52 to access the screw holes that allow you to install on a mount.

Use a flush mount

The TD52 comes with a flush mount in the box. You can use the screw holes of the flush mount to mount the Intercom (see image below for visual):

Mount directly to a wall

Use a mounting bracket

You can use the mounting bracket to install the TD52 on to various surfaces that the flush mount plate cannot, where they’re typically used to mount the TD52 on an exterior surface.

<< Click on the page numbers to go to other pages. >>

This guide explains the setup for each option so that you can determine which one is best suited for your needs and scene..

How to find the camera’s light settings in its web interface:​

Even if the camera is connected to an NVR, before anything, you will need to log into the camera directly to access the advanced image and light settings to enable the different light modes, as these are not accessible from an NVR.
.

By default, your camera will be set to remain in ‘ColourVu only’ mode during low-light, meaning the white light will be constantly on when it is dark and never use its IR. The below sections will show you on how to configure the new ‘Smart Hybrid’ mode, ‘IR only’ mode, and ‘ColorVu only’ mode.
.

.

How do I set my camera to Smart Hybrid mode:​

This mode is utilises both the IR and white LEDs built into your camera. It is useful as it allows you to keep your cameras to stay discreet in IR mode while there is no activity in your scene, and then switch to full colour when a person or vehicle is detected by putting white light on the scene, providing you with all of the additional information a colour image offers while also acting as a deterrent.

Here are the steps to enable this mode:
.

.

How do I set my camera to ‘IR only’ mode:​

This mode is recommended if you would like the camera to be as discreet as possible and your scene is dark at night, as the camera will use its IR LEDs all the time at night and then switch back to colour during the day, meaning the white light is never used.
.

How to Configure Light Settings on Hikvision Cameras

How do I set my camera to ‘ColorVu only’ mode:​

This is the opposite to IR mode, as the camera will turn on its white light at night and keep it constantly on, meaning that its IR is never used. This mode is ideal if you are not worried about the camera being discreet and prefer a colour picture 24/7.
.

How do I find my Hikvision device and edit its network settings?

You probably want to be able to view your camera feeds remotely wherever you are; either in a web browser, the iVMS-4200 software, or the Hik-Connect mobile app. All IP CCTV devices communicate over your LAN (local network) and have a unique location on the network. So, you will need to be able to locate where the device you want to view is and make sure it has the right settings for it to work on your LAN. You will then be able to access the device from a PC or mobile device, and connect it with the rest of your CCTV system.

Please follow the steps beneath to find and correctly set your Hikvision device’s network settings.
.

.

Step 1:
.

The first step is to work out if you need Hikvision’s SADP tool or not. If you only need to discover and access an NVR and some Plug and Play cameras connected directly to its PoE ports, then you don’t need to use it.​

​

​

If you aren’t using the SADP tool:​

​

Or, on the NVR’s local GUI (Graphical User Interface – when operating the recorder from a connected monitor and mouse), go to:​

​

System → Network → TCP/IP​

​

Here, you can view and change the NVR’s network settings to match your LAN which is explained in step 2 – you can then ignore the rest of the steps.​

​

​

If you are using SADP:​

​

If your cameras are connected to your LAN, rather than to an NVR’s PoE ports, you will need to install the SADP tool. This scans for all Hikvision devices on your LAN by their MAC addresses. Now, follow steps 2-5 below.​

Step 2:

​

You now need to identify some of your LAN’s settings, which you need to set to match on your devices.​

​

From a Window’s PC, you will need to use the Command Prompt tool to find these.​

​

If you’re using a Mac, then you can find these by launching System Preferences, and then going to:​

​

Network → Advanced (make sure your Wi-Fi/Ethernet connection is selected on the LHS) → TCP/IP​

​

​

Make a note of the following numbers, as you will need to use them when changing your device’s network settings:​

​

IPv4 Address – This is the IP address of the computer that you are using. This address is therefore already occupied, so you will not be able to assign any other devices to this specific address. The digits after the final decimal point indicate where the device is located within the range of your local network, which spans 1-254. You’ll need to change the number after the third period (or full stop/dot) to something that is between “1” and “254” and not already occupied by another device on the LAN.​

​

NB – Please see these guides for instructions on checking if a proposed IP address is occupied:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

Subnet Mask – This shouldn’t need to be changed on the NVR, it will usually be “255.255.255.0”.​

​

Default Gateway – This is the IP address that’s been assigned to your router. Any device being added to your system needs to be within the range of your gateway in order to be discoverable.​

.

Step 3:

​

Now, launch the SADP tool again. It should show a list of all the Hikvision devices on your local network and their default network settings. Provided the device is being powered and has a connection to your LAN, then it will show up here. You can also alter the device’s network settings here, and check things like the model number, serial number, the firmware version installed on it.​

​

NB – Remember that any camera that is directly connected to your NVR’s PoE ports will not show up in SADP. This is because the NVR hides any cameras directly connected to it from SADP on its own “subnet”, which is separate from your local network. Don’t worry though, as you won’t need to change the settings for these cameras. ​

.

Step 4:

​

Tick the box beside your device to view and edit the network settings.​

​

If the device hasn’t yet been connected to the network then it will show as “Inactive”. You will be asked to set a password for it when you click the tick-box for it. For more instructions on activating your device, please see Part 6.​

​

​

.

.

​

Once activated, ticking the box beside your device will change the network settings in the “Modify Network Parameters” window, so that they match your LAN. You need to make sure that you enter the password for that device before clicking “Modify” for these changes to be saved.​

​

.

Step 5:
.

Check that these changes have been reflected in the SADP device table – you may need to wait a few minutes before refreshing. If they have, then you should be to carry on with getting this device connected to the rest of your system.​

​

NB – If you aren’t the camera’s first owner then you will need to perform a hard reset on it. This will reset the device to its inactive factory state so that you can set new password by activating the camera in SADP. Once this has been done, SADP will allow you to modify each network setting edit the network settings to match your LAN so that you can use the device standalone or add it to your NVR remotely.

How do I set up events and email or push notifications on my Hikvision camera?

Video Analytics, or “VCA events”, are some of the most useful features available on a Hikvision camera. Using these will mean that your footage is analysed in real-time for any activity or abnormalities with your system that you would like to receive an alert for. The different events that are available currently (which ones are available varies which each model of camera) include:

This guide will cover the setup of three of the most popular event options:

Motion Detection – This is one of the first AI options that was introduced and will analyse your footage for any moving object in a specified part of your scene and can alert you as soon as it is detected. As it detects motion in its most basic sense, it uses less of a camera or NVR’s processing power than the other event options, meaning it is always available regardless of your video compression settings.

If you are not using a device with AcuSense then this option will give you the most false-positive alerts, as it offers the fewest ways for filtering out moving objects that you are not interested in, such as object size and the direction or duration of the motion.

Intrusion Detection – This is similar to motion detection in that it will alert you when a moving object is detected within a predefined “intrusion zone”. However, this is better if you want more control over when you are alerted as it will only notify you when a moving object enters the zone, rather than whenever movement occurs within it. This event type also allows you to specify the size of trigger objects, as well as how much of an object enters the zone and for how long before you are alerted.

Line Crossing Detection – This option is particularly useful for various entrances, boundaries, and roads, etc., as it allows you to draw a line in your scene so that you are notified when an object moves across that line. Importantly, you can specify the direction(s) of movement across the line on which you are notified. Like intrusion detection, you also have more control over the size of the trigger object and how much of it must cross the line.
.

Note – Before starting, you will need to check that your Default Gateway and DNS Server are correctly set up in your device’s network parameters, as these need to be right in order for you to be sent email notifications. To check these, please see part 2.​

​

.

Section 1: Setting up motion detection​

​

Step 1:​

Connect to your device’s web browser interface by browsing for its IP address and log into it. If it is recording to an NVR, then connect to this, as this is where you should set your events from.​

.

Step 2:​

Once you’re in, navigate to:​

​

Configuration → Event → Basic Event → Motion​

​

If you’re using an NVR, select your camera from the “Camera” dropdown.​

​

​

Note – To set one of the other VCA event options, you’ll need to go to “Smart Event” rather than “Basic Event”, where you will be shown a list of tabs with all the other available events on your camera. ​

​

Step 3:​

Tick the “Enable Motion Detection” box.​

​

​

Step 4:​

Decide if you want to enable “Dynamic Analysis for Motion”. When this is turned on, green squares will show on anything that triggers motion detection in the camera’s feed, which can help with identifying exactly what has triggered the event.​

​

​

Note – Cameras usually determine what is ‘motion’ in your scene by detecting pixel changes in the image, as a large amount of pixel change usually indicates movement. However, if there is lots of visible noise in your image due to gain control in low light, you will probably see a high number of false alerts on the camera. Using one of the more advanced event types, or the camera’s built-in LEDs to illuminate the scene, will help here. ​

​

Step 5:​

Once you’re happy with the view of your scene, click on the hexagon or “Draw Area” button in “Area Settings”, which will allow you to use your mouse to draw the area within which you would like motion detection to be active.​

​

On Easy IP 3.0 and earlier cameras, These areas will be indicated by a red grid or polygon that appears when you click on part of the scene.​

​

The newer cameras will get you to draw one solid shape for each of your detection areas by left-clicking to set each point of that shape. When you have set all the points that you need, right-clicking will complete the shape and allow you to draw any others that you need.​

​

To clear your zones, just click the cross or “Clear All” button.​

​

Note – If you are not using an AcuSense camera or NVR, then you should make sure that the edges of your detection zones are not on top of anywhere that is likely to see a lot of movement, shadows, or reflections (e.g. roads, foliage, windows or the sky), to mitigate the number of false triggers. ​

​

​

​

Step 6:​

If you’re using an EasyIP 4.0 camera, draw any more detection zones that you need by repeating step 5 above.​

​

​

​

Step 7:​

Adjust the “Sensitivity” bar if you need, which determines how sensitive the detection is to pixel changes. The higher the sensitivity, the more easily motion detection is triggered, meaning you will receive more alerts as a result.​

​

A good starting point for the sensitivity is 60, but you will likely need to tweak this yourself over time to identify the optimum setting for your scene.​

​

If there is lots of activity in your scene, then avoid setting the sensitivity too high so that you don’t receive lots of false-positive triggers.​

​

Note – In the case of Line Crossing and Intrusion Detection, the sensitivity setting refers to the amount of an object that is needed to cross the line, or enter the box that you’ve drawn, before the event is triggered. ​

​

​

.

Step 8:​

If you’re using AcuSense features, then use the “Detection Target” boxes to specify what you want to trigger the event. You can select both “Human” and “Vehicle” here if you are interested in both.​

​

.

Step 9:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

​

.

Section 2: Setting up line crossing detection​

Step 1:​

In a web browser, go to:​

​

Configuration → Event → Smart Event → Line Crossing Detection​

​

If you’re using an NVR, select your camera from the dropdown at the top of the page.​

​

​

​

Step 2:​

Tick the “Enable Line Crossing Detection” box.​

​

​

​

Step 3:​

Click on the line button or “Draw Area” to draw your line on the video feed – you can move, rotate or resize however you like. ​

​

.

Step 4:​

Set your maximum and minimum target sizes by clicking the size filter buttons, and drawing these on the camera preview.​

​

Anything that crosses your line and is smaller than your minimum box, or larger than the maximum box, at the point of the line, will not trigger the event.​

​

You should use objects or vehicles in the scene to guide you here. For example, I have set the minimum target size to be slightly smaller than any car that’s near where I’ll draw my line, and the maximum to be slightly larger than a large HGV.​

.

Note – It doesn’t matter where boxes are on the feed. Also, these boxes will only be visible on this event page, and will not show up on your footage in the live view or playback pages. ​

​

.

Step 5:​

If you’re using an AcuSense camera or NVR, then specify the “target(s)” that you would like to trigger the event by ticking the box. There is no issue with ticking both “Human” and “Vehicle” here. ​

​

​

​

Step 6:​

Specify your “Direction”, which refers to the direction from which an object much cross your line to trigger the event. The different options available are explained beneath:​

​

A<->B – Any object crossing from either direction will trigger​

​

A->B – Any object crossing from side “A” to side “B” will trigger (In this case, from left to right)​

​

A<-B – Any object crossing from “B” to “A” will trigger (In this case, from right to left)​

​

​

​

Step 7:​

Adjust the sensitivity bar to suit your needs. Setting this high will reduce the amount of an object that is needed to cross your line before this is triggered. This will, of course, result in more triggers. As the optimum setting here depends on how busy your scene is, we recommend starting at 60 and then adjusting the bar over time until you find the best results. ​

​

​

​

Step 8:​

Use the “Line” dropdown to select and draw any more lines, repeating steps 2-8 above.​

​

.

Step 9:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

​

​

.

Section 3: Setting up intrusion detection​

​

Step 1:​

In a web browser, go to:​

​

Configuration → Event → Smart Event → Intrusion Detection​

​

If connected to an NVR, select your camera from the dropdown at the top of the page.​

​

.

Step 2:​

Tick the “Enable Intrusion Detection” box.​

​

.

Step 3:​

Click on “Draw Area” to draw your intrusion zone (or “Detection Area”) on the video feed, which can be a 3 or 4 sided shape. Left-click on the camera preview to set each of these points. Once your zone is drawn, you can still move each of the points to change the shape to better fit your area of interest.​

​

Note – If the edges of your zone are very close to a road, foliage, or anywhere that is likely to see lots of movement, then you will likely see a number of false-positive alerts. This is because any movement on these lines can trigger the event. If you can, you should allow for a bit of a gap between these parts of the scene and your intrusion zone. ​

​

​

​

Step 4:​

Set your maximum and minimum target sizes by clicking the “Size Filter” buttons, and drawing these on the live camera feed above.​

​

Anything that enters your configured intrusion detection zone and is smaller than your “Min” box, or larger than the “Max” box, will not trigger the event.​

​

You should use objects or vehicles in the scene to guide you here. For example, I have set the minimum target size to be smaller than the smallest person I’d expect to see in that part of the scene, and the maximum to comfortably cover a very tall person.​

​

Note – It doesn’t matter where boxes are on the feed. Also, these boxes will only be visible on this event page, and will not show up on your footage in the live view or playback pages. ​

.

.

Step 5:​

If you’re using an AcuSense camera or NVR, then specify the “target(s)” that you would like to trigger the event by ticking the relevant box. There is no issue with ticking both “Human” and “Vehicle” here.​

​

.

Step 6:​

Now, adjust the “Threshold” bar as you need. This can be set between 1 and 10 seconds and refers to how long an object needs to be within your intrusion zone before triggering the event. For example, setting this to “0” will mean that the event is triggered as soon as a valid target enters your zone.​

​

.

Step 7:​

Adjust the sensitivity bar to suit your needs. Setting this high will reduce the amount of an object that is needed to enter your zone before the event is triggered. This will, of course, result in more triggers. As the optimum setting here depends on how busy your scene is, we recommend setting this to 60 and then adjusting the bar over time until you find the best results.​

​

​

​

Step 8:​

Use the “Region” dropdown to select and draw any more intrusion zones, repeating steps 2-6 above.​

​

​

Step 9:​

Click on the “Arming Schedule” tab and set this by filling in the hours you want the event to be enabled for in blue.​

​

Note – Please see section [1] step 9 above for a more detailed explanation on how to set your arming schedule. ​

​

​

Step 10:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

.

.

Section 4: Setting the Arming Schedule for your events​

Now that you have set your “Area Settings”, click on the “Arming Schedule” tab to set when the event will be active.

This will bring up a timeline with the week broken up into days and hours – depending on the device that you are using, it might look different to the grid below. If a period is filled in blue then the event will be active (or “armed”) for that hour; If the period is white, the event will be off.

Use your mouse to draw up the weekly Arming Schedule that suits. You can also use the popup box that appears when you click on any blue period to finely adjust the start arming times:
.

Clicking on the “Erase” button and then a blue period will allow you to clear the arming:
.

When you’re happy with this schedule, click “Save”.

.

.

Section 5: Setting up email & push notifications for your events​

.

Click on the Linkage Method tab on the event’s page (shown above), which is where you will set up your email notifications, as well as other alert types.​

​

The different options are explained below:​

​

Audible Warning: This will cause the NVR / browser to bleep when on event triggers.​

Send Email: This will set the NVR to email you on event triggers, with a screenshot of the camera’s view at the time.​

Notify Surveillance Centre: This refers to Hik-Connect and needs to be activated in order to receive push notifications in Hik-Connect.​

Full Screen Monitoring: This will get the NVR to automatically throw up a camera’s live feed in full screen during a trigger for an event set on that camera.​

​

​

.

.

To enable Hik-Connect push notifications:​

.

To set up push notifications, you need to make sure that Notify Surveillance Centre is ticked as a “Linkage Method”.​

​

You also need to make sure that push notifications are enabled for Hik-Connect in your phone’s settings. To enable them via the app, go to:​

​

More → Settings → Enable Push Notification​

​

​

……..

.

New GUI – Start Up Wizard (Device Initialization)

DAHUA XVR 4.0 Setup Description

This article will go over the Initialization process of the units with the New GUI.

Prerequisites

Video Instructions

Step by Step Instructions

1. When you first turn on the recorder you will be greeted with the region settings. Click on the drop down menu and select “United States” and click Next.

2. Select the proper time zone setting for your region.

3. You will now be prompted to input a password for the admin account.

4. For easier login you can create a pattern, you will need to enter it twice to confirm.

5. Enter your email in order to reset the admin password in case the password was forgotten, you may also setup security questions.

Note: This is the only method to reset the password for XVRs and NVRs. If you skip this step and forget your device’s password, you will need to replace the unit

6. The Auto-check for firmware is not yet implemented in the U.S. so you can just click on next.

7. Make sure the video standard format is set to NTSC and click on “Next”.

8. Here you can go in depth with the time settings. You may want to set up the DST (Daylight savings) so that it takes affect when the time comes.

9. The recorder will be set as a static default IP address you see on the screen. Input an open local IP address and gateway from you network. If you don’t know this information you can select DHCP (highlighted in the red box) in order to automatically receive an IP address from the router.

10. If you have the recorder properly connected to the router the P2P status will indicate “Online” and you can now remote in to the unit with our mobile app/PC app.

11. You can select the Encode settings for each camera by selecting the drop down menu on “Channel”.

12. Select the resolution and image quality for snapshots.

13. Select what you want to to when the hard drive fills up.

14. Here is you recording schedule, the green will indicate 24/7 recording and Yellow will be Motion recording.

15. Here is you Snapshot schedule, same color legend as recording,

16. Once all that is setup you will be greeted with the final Prompt! You are now finished Initializing you new recorder

New GUI- Add a Dahua Device

Description

This article will show you three different methods to add a dahua device to our New GUI recorders. We will be adding a dahua camera with all three methods.

Prerequisites

Video Instructions

Step by Step Instructions

Method 1:

This first method is extremely simple if all the cameras are still set to default credentials and settings. We will do a device search on the network and add them with a click of a button

Method Two:

The second method is used if there’s an existing camera and it’s password was changed. You will use device search to locate the camera and then go to manual add to change the password it’s being added with

Method Three:

This last method is used when Device Search fails and cannot locate the camera on the network. You will need to type in the camera’s information manually.

New GUI – Account Setup

Description

This article will go over how to add a user on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Log into the web interface of the device

.

2. Click the Menu icon in the top left of the page

.

3. Select Account

.

4. Click Add User

5. The Add User menu will appear. Use this window to ill out full user details

6. In the Authority menu you can define the individual rights of the User using the System, Playback, and Monitor tabs as well as which channels the user can access

Select which features you wish the user to have then click Save

7. A message will confirm when the user is successfully added

New GUI – Schedule Record Setup

Description

Dahua NVRs and DVRs offer a variety of recording options. You can configure recording schedules based on the following methods:

These schedules can be set individually for each camera or copied to all cameras.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Management”.

2. Select the “Storage” option from the drop-down menu.

3. From the left hand side, select “Schedule”.

4. Select the channel drop-down menu to choose the channel that you want to adjust the recording schedule for.

5. Select “Setting” next to any day of the week.

6. You will have options to set a schedule for General Recording, MD (Motion Detection), Alarm, MD & Alarm, Intel, and POS (Point of Sale). For this tutorial we are using General Recording.

7. Here you can see that you are able to set multiple periods. For this tutorial we will only be setting one period. Check the “General” box, then select the day or days you want to scheduled recordings for, and then select “Save”.

8. Depending on the days selected from the previous step, you will see green colored bars which represents general recording.

9. You can select “Copy” to mirror the same schedule to another channel/camera. Select “Save” in the Copy menu.

10. Select “Save” at the bottom to save all settings. If your changes were successfully saved, a pop-up will appear at the top notifying you as such.

New GUI – Motion Detection Recording Setup

Description

This article will go over Motion Detection Recording setup in detail on the recorder’s new GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. On the main menu select Alarm

2. Select Video Detection on the left.
Then select the Motion Detection tab at the top.
Choose the channel from the drop-down next to Channel.
Check the box next to Enable.
Check the box next to Record Channel.
Click on Setting next to Region

3. Highlight the areas in red where you want to track motion.
Then click OK at the bottom

4. Select More at the bottom
Check the boxes next to any of the other options you want to activate when motion is detected.
Click on OK

5. Click on Apply at the bottom.
You will see “Operation Succeeded” at the top when your changes have been saved

6. Click on the Setting drop-down at the top and select Storage

7. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel from the drop-down next to Channel.
Click on the Setting button next to any day of the week.

8. Check the All box to enable all days of the week.
Check the Motion box for “Period 1”.
Click OK at the bottom.

9. Click on Apply at the bottom to save the settings

10. Select Record Mode on the left.
Then make sure Auto is enabled for the appropriate channel(s).
Click on Apply at the bottom.

11. Click on the Main Menu icon at the top right.
Then select Search

12. Check box next to the channel on the right.
You should see yellow lines/bars for motion recording

Alarm Record Setup

Description

This article is to show you how to setup alarm recording thru new Web GUI.

Note: please refer to product spec sheet for alarm input/output availability. Not all Dahua Recorder support alarm input/output.

Prerequisites

Video Instructions

Step by Step Instructions

Setup Alarm Input

From main menu, click on Alarm. Click on Alarm input. We are using XVR 72 series for this example. The Alarm Input page will launch as shown below:

Select the Alarm input number that you like to use. This number is correspond to the alarm port on the back of recorder.

1. Click Enable to enable the alarm input.

2. Enter Alarm Name. By default is set to AlarmIn#

3. Period is to schedule your Alarm when you want to be enable.

4. With the alarm input, you can trigger recorder’s alarm output.

5. This to select which channel you want recorder to start recording when alarm is triggered.

6. You can call basic PTZ action Preset, Tour, or Pattern when alarm is triggered.

.

Setup Alarm Recording Schedule

1. From the main menu, click on Management > Storage > Schedule.

2. Select the channel you like to setup.

3. To enable Alarm recording, Click on Setting next to the timeline bar.

4. Set your duration (By default is 24 hour, 00-24). Then select Alarm.

You can select all days to copy the schedule to all week. Click Save.

5. Click Save.

New GUI/Instructions/IVS Record

Description

This article will cover how to configure IVS Recording on a Dahua recorder with the New GUI

Prerequisites

Video Instructions

Step By Step Instructions

1. From the Main Menu select AI

2. Select Parameters on the left.
Then select Smart Plan below it.
Choose the channel of the camera you are configuring from the Channel drop-down.
Select the IVS “Lightbulb” icon so that it highlights blue.
Then click Apply at the bottom

3. Select IVS on the left.
Choose the channel of the camera from the Channel drop-down.
Then click the + button.
Double-click on the rule type under the Type column to choose the type of IVS rule you want to use.
Adjust all the settings in the Parameters section.
Make sure that the box is checked next to Record Channel and the channel that camera is on is highlighted next to it

4. Draw the rule in the live view on the left by left clicking on it.
Continue to left click to add more segments.
When you are done, right click to finish drawing the rule.
Then click Apply at the bottom

5. Select Setting at the top left.
Then select Storage from the drop-down

6. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel of the camera from the Channel drop-down.
Then click on Setting to the right of any day of the week

7. Check the box next to All to select all days of the week.
Check the box for Intelligent to the right of Period 1.
(Feel free to adjust the days of the week and the time period for when you want to record IVS events).
Then click on OK

8. You will see blue bars on the schedule representing when IVS events will be recorded, when they are triggered.
Click Apply at the bottom

9. Click on the Menu icon at the top right to go back to the Main Menu.
Then click on Search

10. Check the box next to the camera channel on the right.
Once IVS events have occured they will appear as blue bars on the timeline at the bottom.
Click on the timeline on one of the blue bars to start playing that IVS event

New GUI – Audio Record Setup

Description

This article will go over setup for audio recording on our New GUI devices

Prerequisites

OR

Note: Please reference the specification sheet for the device to confirm which audio features it supports, this can vary between models of recorder

Video Instructions

Step by Step Instructions

Enable audio source

1. 1. Login using a web browser.

2. Click on Setting > Camera.

|

3. Click on Encode. And then select the camera channel that support audio.

|

4. Click on More.

5. Click on the checkmark to enable Audio.

6. Select the Audio source for your HD-CVI camera. If your HD-CVI camera has built-in Microphone, select HDCVI as the audio source. Local option is if you are connecting external microphone to the recorder.

7. Click OK, and then click OK again on the bottom right hand corner.

Setup audio recording

1. Login using a web browser.

2. Main menu 1st screen.

3. Main menu 2nd screen.

4. Click on the Audio Option.

5. Audio File Manager Option.

New GUI – Playback

Description

This article will cover how to play back recorded video on an NVR or DVR with the New GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Video”

2. The Playback menu should open up and look like this:

3. On the right hand side, there will be a calendar. Select the day that you wish to play back video.
Below the calendar is a list of all the cameras/channels. Check the box next to all the cammeras/channels you would like to play back video from.

4. The video footage willl appear on the timeline at the bottom of the screen. It will be color coded to match the types of video that were recorded.
(See the Legend at the bottom of the screen.)

5. Check or uncheck each type of recording that you want to view. Check the Sync box if you would like to sync playback up on all channels you are viewing.

6. Double click on the graph at the bottom to begin playing back video.

=How to back up video files on new UI

Description

This article is to show you how to back up the video file from new system UI.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the main menu, go to the second menu page, and click on Backup.

2. Backup page will launch as shown below:

3. You must plug in an external drive to save your downloaded file. Select the path where you want to save the file at. From this pop-up screen, you have an option to create new folder. After you select, click OK.

4. Select the Record Channel you like to search. You can only search 1 channel at a time.

5. Select the Recording Type you like to search.

6. Set the start and end time for searching. Then click Search. All recorded files that meets your search criteria will shown on the list.

7. Select the files, and click Backup.

8. Downloading process start.

9. Once finished, the folder information will pop up, then click OK.

New GUI – P2P Setup

Description

This article will go over initializing P2P on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Under “Management” go to Network>TCP/IP

2. You can either set the device on a static ip or turn DHCP on to automatically grab an IP from the network. Save any changes

3. Locate P2P tab on the lower left and enable P2P

4. After saving it you should see the the status change to “Online”, You can now use this device for remote viewing on our software

Remote Access/Remote Access Setup Port Forwarding

Create port forwarding rule in the router

Description

Port forwarding is a function of network routers that allows a user to configure specific communication ports to be routed to devices on an IP (Internet Protocol) network, such as a computer, DVR, or IP camera.In this case for CCTV equipment, it allows the user to view and control CCTV equipment remotely. Follow the step by step instructions and the instructions your manufacturers hardware to setup port forwarding, or try PortForward.com to search for your routers settings.

Prerequisites

Video Instructions

Step by Step Instructions

1. Connect NVR to network with a CAT5 cable.

2. Download and install ConfigTool from DahuaSecurity.com, under Support->Download Center->Software

3. Run the ConfigTool.

4. The ConfigTool should display your IP Camera. Click the, “” icon to open Internet Explorer and access your NVR.

5. Configure Internet Explorer security settings to allow the plugs to work. Link to Internet Explorer Setup

6. Login with the default credentials: User Name: admin Passsword: admin

7. Under, Main Menu -> Setup -> TCP/IP Change the IP Camera to, “Static” if the camera is currently set to, “DHCP”

8. Open another tab and enter the, “Gateway” address listed under your NVR’s Network settings. Example: 192.168.1.1, 192.168.0.1, 10.0.10.1

9. Login to your gateway and locate the, “Port Forwarding” section.

10. Create port forwarding rules for each port you wish to forward for the NVR. (Usually you will only need to forward the HTTP and the TCP port.) Default Ports: TCP: 37777 UDP: 37778 HTTP: 80 RTSP: 554 HTTPS: 443

11. The end result should look like the below image. We used a Cisco router for this example.

12. Hit, “Save” in the gateway interface, and open another tab.

13. Go to, “www.canyouseeme.org” and check that the ports you opened on the gateway.

How to Access System Using P2P via Mobile Application

Description

View your recorder and cameras on the go. With Dahua’s mobile application IDMSS(IOS)/GDMSS(Android) allows you to add Dahua recorders and cameras to the mobile app using P2P.

Prerequisites

Video Instructions IDMSS/GDMSS version 4.50.000

Step by Step Instructions iDMSS/gDMSS version 4.50.000

1. Open iDMSS/gDMSS on the phone, and select the home icon located on the top left corner.

2. Select the “Device” button/icon on the bottom to add the recorder/camera.

3. Select the “+” sign then select “Scan” to add the device.

4. Select the “Wired Camera”.

5. Input the device for easy identification. It’s required to input the password for the added device then select the save icon located on the top right corner.

Step by Step Instructions IDMSS/GDMSS version 4.20.000

1. Select the Menu Icon

2. Select “Device Manager”

3. Select the Add Icon

4. Select “Camera”

5. Select “Wired Device”

6. Select “P2P”

7. Input Info and select “Start Live Preview”

Video Instructions IDMSS/GDMSS version 3.50.000

Step by Step Instructions IDMSS/GDMSS version 3.50.000

1. From the home screen of the mobile application select “Camera”.

2. Select the menu button.

3. Select Device Manager.

4. Select add button to add device.

5. Select Wired Device.

6. Select P2P.

7. Name your device -> tap the QR code to bring up QR code scanner.

8. Input the username -> password -> and select live preview. By selecting “Start live preview” device will be automatically saved into the application.

IDMSS/GDMSS Version 3.40.003

Video Instructions Version 3.40.003

Step by Step Instructions Version 3.40.003

1. Click, “Camera”

2. Select the Menu Icon

3. Select “Device Manager”

4. Select the Add Icon

5. Select “P2P”

6. Choose a name for the device → Scan in QR code for SN number which you can access from the physical recorder under the main menu → Setting → Network → P2P. You may input SN number manually which can also be found under the recorder. → Enter Username and Password. For best results , leave Live Preview and Playback on the Extra Stream.

7. Select the Disk Icon to save → Select Live Preview, At which time the app will connect to all cameras.

Setup Remote Access via P2P using SmartPSS

Description

This allows you to view cameras on SmartPSS using P2P.

Prerequisites

Video Instructions

Step by Step Instructions

1. Locate the serial number of your NVR or DVR. The serial number can be found at the following locations:

2. Launch SmartPSS and select Device.

3. Click Add, change method to P2P.

4. Enter credentials, save and then add.

.

Create port forwarding rule in the router

Description

Port forwarding is a function of network routers that allows a user to configure specific communication ports to be routed to devices on an IP (Internet Protocol) network, such as a computer, DVR, or IP camera.In this case for CCTV equipment, it allows the user to view and control CCTV equipment remotely. Follow the step by step instructions and the instructions your manufacturers hardware to setup port forwarding, or try PortForward.com to search for your routers settings.

Prerequisites

Video Instructions

Step by Step Instructions

1. Connect NVR to network with a CAT5 cable.

2. Download and install ConfigTool from DahuaSecurity.com, under Support->Download Center->Software

3. Run the ConfigTool.

4. The ConfigTool should display your IP Camera. Click the, “” icon to open Internet Explorer and access your NVR.

5. Configure Internet Explorer security settings to allow the plugs to work. Link to Internet Explorer Setup

6. Login with the default credentials: User Name: admin Passsword: admin

7. Under, Main Menu -> Setup -> TCP/IP Change the IP Camera to, “Static” if the camera is currently set to, “DHCP”

8. Open another tab and enter the, “Gateway” address listed under your NVR’s Network settings. Example: 192.168.1.1, 192.168.0.1, 10.0.10.1

9. Login to your gateway and locate the, “Port Forwarding” section.

10. Create port forwarding rules for each port you wish to forward for the NVR. (Usually you will only need to forward the HTTP and the TCP port.) Default Ports: TCP: 37777 UDP: 37778 HTTP: 80 RTSP: 554 HTTPS: 443

11. The end result should look like the below image. We used a Cisco router for this example.

12. Hit, “Save” in the gateway interface, and open another tab.

13. Go to, “www.canyouseeme.org” and check that the ports you opened on the gateway.

Dahua XVR Remote Access Full Guide

Read Also : 2MN NVR XVR Troubleshooting 2024

How to locate device on LAN via ConfigTool 3.20

Description

Prerequisites

Video Instructions

Step by Step Instructions

Note: If your IP Camera is connected to the back of an NVR, these instructions will not apply. Please see, “How to Connect IP Camera to NVR” 

1. Download and install ConfigTool.

2. Run the ConfigTool.

3. The ConfigTool should display your IP Camera’s IP address. Click the, “” icon to open Internet Explorer and access your IP Camera. Alternatively, you can input that IP address into your browser manually.

4. Login with the default credentials: User Name: admin Passsword: admin

Configure Internet Explorer Security Settings

Prerequisites

Video Instructions

Step by Step Instructions

1. Open Internet Explorer.

2. Click on the gear icon in the upper right hand corner

3. Click, “Internet Options”

4. Click the, “Security” tab.

5. Click the, “Trusted sites” icon.

6. Click the, “Sites” box immediately below the zones.

7. Input your devices IP address into the top box, click, “Add” and then, “Close”

8. Click, “Custom level…”

9. Click the drop down box at the bottom of this window, and change the setting to, “Low”

=>

10. Click, “Reset” and then, “Yes” in the confirmation dialogue.

11. Click on the, “Advanced” tab.

12. Ensure the following are ENABLED:

13. Click, “Apply” and then, “OK”

14. Reboot your computer, and try to access your system.

Add a Device via P2P using SmartPSS

Description

This allows you to add cameras or recorders via P2P to SmartPSS

Prerequisites

Video Instructions

Step by Step Instructions

1. Locate the serial number of your NVR or DVR. The serial number can be found at the following locations:

• 

On the underside or side of the unit

• 

In the web interface, under Info->Version

• 

On the system interface under Main Menu->Settings->Network->P2P

• 

On the system interface under Main Menu->Info->System->Version

2. Launch SmartPSS. At the main page click Devices

3. Click +Add to add a device

4. The Manual Add window will appear.

5. Use the drop-down box to change ‘Method to add’ to ‘SN(For Device Support P2P)’

6. Enter the Serial Number for the unit in the field SN.

Enter the username and password for the device then click Add

7. The added device will appear in the Device List

8. From the main page of SmartPSS click Live View

9. The added device will apear in the Device List and can be expanded to view all video channels from the device.

DDNS Setup

Description

DDNS stands for Dynamic Domain Name System. The main advantage for DDNS is If you have a dynamic ip address, (where your address can change monthly by your ISP if not static) the DDNS service will track and update with your new IP address automatically. So no matter what your numeric IP address is, your DDNS address will work even if your numeric IP address changes.

Prerequisites

(port 37777 is default, 38888 is an example)

Video Instructions

Step by Step Instructions

Step 1. From the Main Menu Select Network

Step 2. Select DDNS ➞ Check off the “Enable” box.

Step 3. Select “DDNS Type” from the Drop Down menu. Please Note depending on the series model of the recorder you will have either Dahua DDNS or Quick DDNS as one of the options from the drop down menu.

After DDNS is selected it will automatically generate a Host IP. In this case because Dahua DDNS is an option it is www.dahuaddns.com . If Quick DDNS is an option it will automatically generate the designated www.quickddns.com as the host IP.

.

Step 4. Select either “Default Domain” or “Custom Domain Name”. By Selecting “Default Domain” a Domain Name for the device recorder is the MAC address for this recorder. In this case 4C11BF0B0436.dahuaddns.com is the designated default domain name for this particular recorder. By selecting “Custom Domain Name” you may choose a custom name up to 60 max characters. Please note if you are using a custom domain name you cannot use the same custom domain name from or for another device.

Step 5. Input your email address ➞ Select “Test” and if successful it will prompt a pop up “Successfully Registered” ➞ Select “Yes” ➞ Select “Apply” ➞ Select “OK” to save settings.

DDNS Web Registration and Management

For QuickDDNS Go to www.quickddns.com

For DahuaDDNS Go to www.Dahuaddns.com

Please Note You cannot access the settings, live view or playback of the recorder through DDNS.

Step 1. DDNS Registration Click on Not registered link → Enter the registration page → Follow system instructions to complete registration.

Step 2. Go to The email you registered with to activate ddns account.

Step 3. After you have activated your username, you can log in DDNS website to manage and view devices under your account. When you login DDNS website, go to Equipment where you can view and manage devices under your account. Click on device domain name link to open corresponding Web interface.

Dahua DDNS Setup

NOTICE

Notice of Discontinuation of DahuaDDNS & QuickDDNS

Click Here to Download PDF Document

Description

DDNS stands for Dynamic Domain Name System. The main advantage for DDNS is If you have a dynamic ip address, (where your address can change monthly by your ISP if not static) the DDNS service will track and update with your new IP address automatically. So no matter what your numeric IP address is, your DDNS address will work even if your numeric IP address changes.

Prerequisites

(port 37777 is default, 38888 is an example)

Video Instructions

Step by Step Instructions

1. Go to www.DahuaDDNS.com and

2. Click, “Not Registered”

3.Input your information, and click, “Register”

4. Open your email and locate the activation email. Click the link in that email.

5. If you see the below message, please proceed with the below instructions. 

Enable Domain Name Access on Device

1. After the device boots up, please wait 1 to 3 min until the network indicator becomes green.

2. Locate your device with the ConfigTool. Click Here to Download ConfigTool.

3. Input your device’s IP address into Internet Explorer, and login.

4. Go to Settings -> Network -> DDNS

5. Click, “Test” once the test is complete, click, “Save”

DDNS Setup No-IP

NOTICE

Notice of Discontinuation of DahuaDDNS & QuickDDNS

Description

This article is a step by step setup guide for NoIP DDNS. NoIP DDNS is Dynamic Domain Name System which is a method of automatically updating a name server. This is primarily used if your public IP address on the internet changes from time to time (dynamic IP). Setting this feature up will give you another configured hostname.

Prerequisites

(port 37777 is default, 38888 is an example)

Video Instructions

Step by Step Instructions

1. Go to https://www.noip.com/

2. Create an account -> Go to your email registered with noip.com. An email activation will be sent to your registered email to activate noip.com account.

3. Once account is activated select “Create Host Name Now”

4. Input a host name of your choice > Select Add “Host Name”

5. Login into Recorder via Web Service or Physical recorder. From the Main Menu select the network tab > Select DDNS on the left hand side. Check off “Enable” > Click on Drop down to select “No-IP”

6. Input host IP > Domain Name > User Name > Password > Do not forget to click “APPLY” to save settings.

Enabling Quick DDNS from Local Recorder

Description

This article is a step by step setup guide for Quick DDNS. Quick DDNS is Dynamic Domain Name System which is a method of automatically updating a name server. This is primarily used if your public IP address on the internet changes from time to time (dynamic IP). Setting this feature up will give you another configured hostname.

Prerequisites

(port 37777 is default, 38888 is an example)  

Video Instructions

Step by Step Instructions

1. From the Main Menu Select Network

2. Select DDNS ➞ Check off the “Enable” box.

3. Select “DDNS Type” from the Drop Down menu. Please Note depending on the series model of the recorder you will have either Dahua DDNS or Quick DDNS as one of the options from the drop down menu.

After DDNS is selected it will automatically generate a Host IP. In this case because Dahua DDNS is an option it is www.dahuaddns.com . If Quick DDNS is an option it will automatically generate the designated www.quickddns.com as the host IP.

.

4. Select either “Default Domain” or “Custom Domain Name”. By Selecting “Default Domain” a Domain Name for the device recorder is the MAC address for this recorder. In this case 4C11BF0B0436.dahuaddns.com is the designated default domain name for this particular recorder. By selecting “Custom Domain Name” you may choose a custom name up to 60 max characters. Please note if you are using a custom domain name you cannot use the same custom domain name from or for another device.

5. Input your email address ➞ Select “Test” and if successful it will prompt a pop up “Successfully Registered” ➞ Select “Yes” ➞ Select “Apply” ➞ Select “OK” to save settings.

.

DDNS Web Registration and Management

For QuickDDNS Go to www.quickddns.com

For DahuaDDNS Go to www.Dahuaddns.com

1. DDNS Registration Click on Not registered link → Enter the registration page → Follow system instructions to complete registration.

2. Go to The email you registered with to activate ddns account.

3. After you have activated your username, you can log in DDNS website to manage and view devices under your account. When you login DDNS website, go to Equipment where you can view and manage devices under your account. Click on device domain name link to open corresponding Web interface.

View the RTSP stream with VLC media player

Prerequisites

Example URLs

Video Instructions

Step by Step Instructions

1. Download and install VLC. Click here to go to VLC Homepage

2. Click Media—Open Network Stream.

3. Input RTSP URL in Network Tab.

4. Click Play button, then the video will display.

About the URL of the RTSP, please see the explanation as follows.

URL Syntax

rtsp://:@:/cam/realmonitor?channel=&subtype=

For example, we request the extra stream 1 of channel 1,the URL is: rtsp://admin:admin@10.7.6.67:554/cam/realmonitor?channel=1&subtype=1.

The IP Camera supports both TCP and UDP transmission forms. It also supplies basic authentication and digest authentication ways.The authentication process is similar with 3.2 Authentication.

For the RTSP port, it is 554 in default, If it was changed, please change the port number in the RTSP URL.

For the IPC, you can see the RTSP port in the Web page:

Two Way Talk Setup

Description

This section will show how to setup / use Two Way Talk function with Dahua devices.

Testing

Computer Audio Setup Prerequisite (WebUI, SmartPSS and DSS Express)

• 

Typical Computer Audio Interface (inputs/Outputs)

• 

Microphone plugged into Microphone input (red) Speaker plugged into Output (green)

• 

Both Microphone and speaker plugged into computer

SystemUI Old

Prerequisites

Video Instructions

Step by Step Instructions

1. From Live View

2. Hover the mouse cursor near the top of the screen until the bar appears

3. Click the Microphone icon to begin Two Way Talk

4. The icon will highlight when Two Way Talk is active

5. Click the icon again to end Two Way Talk

SystemUI New

Prerequisites

Video Instructions

Step by Step Instructions

1. From Live View

2. Hover the mouse cursor near the top of the screen until the bar appears

3. Click the Microphone icon to begin Two Way Talk

4. The icon will highlight when Two Way Talk is active

5. Click the icon again to end Two Way Talk

How to Setup FTP to Record Snapshots and Sub-Stream

1. Download SmallFTPD from the following link: http://sourceforge.net/projects/smallftpd/

2. In the root of one of your hard drives, create a folder titled, “FTP”

3. Locate the file you downloaded and extract the contents of the zipped file to the FTP folder you just created in the root of your hard drive.

Your computer should look similar to the image above.

4. Double click, “smallftpd.exe“

5. Click, “Settings” and then, “General”

6. Note the port, and click, “OK”

7. Click, “Settings” and then, “Advanced”

8. Click the box next to, “Use local IP” and click, “OK”

->

9. Click, “Settings” and then, “Users”

10. Click, “Add”

11. Input the following:

Login: admin

Password: admin

Max. simultaneous connections:3-100

Inactivity timeout(s): 999

12. Under Directories click, “Add”

13. Leave Virtual Path set to, “/” and set the Physical path to, “C:/FTP” and click, “OK”

14. Under Permissions click, “Add”

15. Leave Virtual Path set to, “/” and set the Permissions to, “LRW” and click, “OK”

16. Click, “OK” to exit the User Properties.

17. Click, “OK” to exit the User Menu.

18. Click the, “Play” button to start the FTP server.

19A. For a NVR or DVR, go to Main Menu-> Settings -> Network -> FTP, and input the following: NVR or DVR

Host IP: (Your PC’s IP address)

Port: 21 or the port you setup earlier in SmallFTPD

User Name: admin

Password: admin

Remote Directory: /

File Length: 10-512

Image Upload Interval: 10-60

Channel: (any)

Period: (any)

19B. For an IP Camera, login to the IP Camera via web browser and navigate to, Setup-> Storage -> Destination -> FTP, and input the following:

IP Camera

Server Address:(Your PC’s IP address)

Port: 21 or the port you setup earlier in SmallFTPD

User Name: admin

Password: admin

Remote Directory: /

Once complete click, “Save” or “OK”

20. Once complete, check the SmallFTPD and the “C:/FTP” folder. They should look like the below images:

 and 

How To Setup FTP Snapshot

Please Note You must have an FTP currently set up for this to work.

Step 1. From the Main Menu Select Camera > Encode > Snapshot

Step 2. Select Manual Snap Time. This selection will determine how many snapshots are taken at a time.> Select Channel you want snapshot enabled for > Select Mode Trigger or Timing. Trigger is for events such as motion detect or alarm. You can use timing to set periods for which day of the week and or time you want to snapshot > Select image size > select image quality > select interval > Select “Apply” > Select “OK”

• For Timing Go to the Storage tab > Select Schedule Select Snapshot > Choose which type of event snap shot such as motion, alarm and or IVS if model has IVS capabilities. > Set schedule for which event for the periods, days and hours you wany snapshots set for.

• You can also set the schedule by selecting the settings icon.

•For Trigger Go to Event tab > Choose event type > Check Enable > Check Snapshot and channels > Repeat process for the different types of events > Apply > Save

Step 3. Select Network Tab > Select FTP

Step 4. Check Enable > FTP Server address > Input Username > Input Password

.

Step 5.Select Channel or all channels > Select Day or all Days > Input period times > Check off event types such as Alarm or Intel > Click “Apply” > Click “Save”

UPnP (Universal Plug and Play)

Definition

Prerequisites

Step by Step Instructions

1. From the local Device Recorder Menu select Networking

2. Select Networking ➞ Select UPnP

3. Select “Enable” ➞ Select OK Apply ➞ Save

Multicast

Here you can set a multiple cast group. Please refer to the following sheet for detailed information.

-224.0.0.0-239.255.255.255

-“D” address space

-224.0.0.0-224.0.0.255

-TTL=1 When sending out telegraph

-For example

224.0.0.13 PIMv2 router

-239.0.0.0-239.255.255.255

-Private address space

Except the above mentioned addresses of special meaning, you can use other addresses. For example:

Multiple cast IP: 235.8.8.36

Multiple cast PORT: 3666.

After you logged in the Web, the Web can automatically get multiple cast address and add it to the multiple cast groups. You can enable real-time monitor function to view the view.

Please note multiple cast function applies to special series only.

PPPoE

PPPoE interface is shown in the above image. Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider). Click save button, you need to restart to activate your configuration. After rebooting, NVR will connect to internet automatically. The IP in the PPPoE is the NVR dynamic value. You can access this IP to visit the unit.

.

How to reset the password to your Gamut recorder

This article will show you how to find the necessary information you need to send us so that we can help to reset the password for your Gamut recorder.

.

First, turn the recorder on and move your mouse to the bottom of the camera live view screen. A blue bar will appear at the bottom; click on the ‘i’ symbol that I have marked in red in the screenshot below.

.

.

This will open up a page of information about the recorder including the MAC address.

.

.

You will need to send the MAC address and the date and time on the recorder, even if the time/date on the recorder is not actually correct. 

.

This is very important, because we will generate a temporary password for you which is created based on the unique MAC address of the device and the time and date on it. If the date and time are accurate, just say that, or if you know it is five hours behind but the date is correct for example, just mention that when you email in and that should be sufficient. 

.

Otherwise, just send in a picture clearly showing the MAC address and date/time on the device and say exactly when the picture was taken.

.

Get in contact here, set the support status as ‘Password reset’ and the email subject as ‘Gamut password reset’. You will also need to send your original order/invoice number and the original delivery postcode to confirm your identity.

We will try to get back to you as soon as possible.

How to set up and view your Gamut PTZ on a Windows or Apple computer (GTIP210PTZ)

Purpose of The Guide

This guide will walk you through the initial configuration of your Gamut PTZ and show you how to view the camera on your computer.

.

Before You Begin

Let’s Get Started

First we need to make sure that the camera is talking to your network. If you look on the box for the camera and on the side of the camera itself you should see a sticker that looks something like the one shown below.

.

.

Make a note of the IP Address, User name and any Password shown on the sticker.

.

Next we need to open Internet Explorer on the computer. In the address bar at the top of the page enter the IP address that you saw on the sticker. You should then be prompted to log in to the camera, here you need to use the User name and Password shown on the sticker, if there is no password on the sticker then leave the password field blank.

.

Please make sure that you are using Internet Explorer and not any other browser. The reason for this is that most CCTV systems require the use of software called Active X to be able to display your live video and that software is only supported by Internet Explorer.

.

If you are prompted to install any software you need to allow this to happen, this software enables your computer to display the video feed from the camera.

.

At this point you should be seeing a live view from your camera and can go ahead and fit your camera wherever you need it. To watch your cameras in future you will simply need to open Internet Explorer, go to the IP Address from before and log in to the camera. From there you can also control the motion of the camera by using the PTZ controls shown below. These features are explained more in depth in other guides which can be found here.

.

If you were unable to access your camera this way then it’s not a problem, we just need to use a different method. Alternatively if you wish to view the system without having to log in through Internet Explorer each time then continue reading and you will see how to view the camera without needing to log in each time.

.

First open CMS5/VMS, the program that you installed before we began, and click on Device Manager. You will now be presented with a screen that looks like this:

.

.

You should see a camera in the list that has the same IP Address as previously seen on the sticker on the camera. If you don’t then click the IPV4 Search button and after a few moments the camera will appear. Select the camera by ticking the box to the left of it and click Add.

.

The camera will now be displayed in the bottom half of the window. Towards the right hand side you will see a number of buttons, you need to press the Modify IP button as highlighted in the following image.

.

.

At this point if you wish to use the camera through Internet Explorer rather than CMS5 you are now able to. Make a note of the new IP address that the camera is displaying and follow the steps detailed near the top of this guide for accessing the camera using Internet Explorer.

.

Now click the Home button to return to the main page for CMS5/VMS, then click Monitor. On the right hand side you will see your camera in the list of devices. Double click on your camera and the video feed will appear in the middle of the screen. If you then double click on the video if will go in to full screen mode so you can see a larger picture. To then control your camera click the button shown below and the PTZ controls will appear. As before more articles about controlling your camera can be found by clicking here.

.

GAMUT RECORDER Installation and user guide

Read More : UNV Recorder Set Up Guide

How to add your Gamut recorder or camera to a mobile phone or tablet

Purpose of The Guide

This guide will show you how to add your Gamut camera or recorder to a phone.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. If you have a recorder with a hard drive you will need to use a TV or Internet Explorer to set it up for the first time, follow the quick start guide to do so.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

You will need to download the app RXCamView onto your phone or tablet.

Android

.

Apple

.

Let’s Get Started

Open up RXCamView on your device and tap on the head and shoulders icon to open the side menu.

.

Then tap on ‘Device List’.

.

.

On the Device Manager page, tap on the ‘+’ icon then tap on ‘IPC/NVR/DVR’.

.

.

The app will request permission to use your camera, allow it to. It will open up your camera and you need to point the camera to the QR code on the label on your recorder or camera.

.

.

Once you have successfully scanned the QR code the app will prompt you to fill in some information. Leave the IP/Address and Media Port fields, the username is admin by default, and the password is blank by default.

.

Then the device will appear in the device list, it should say ‘Connected’. If it says ‘connect close’ then check the password is correct and that nothing has been disconnected.

.

.

If you tap on the play icon underneath the device, you will be taken to the live view window. Just tap on the name of the device to begin live view.

.

.

To view recordings, just tap on the film reel icon at the bottom right below the live view screen:

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

.

If you find that the device only works when you are connected to the same internet router as it, and not when accessing it via another Wi-Fi network or with 4G, take a look at this guide.

How to access your Gamut camera or recorder using a Windows or Mac computer

Purpose of The Guide

This guide will show you how to access the live footage, recordings and settings of your Gamut camera or recorder, using a Windows or Mac computer.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. You will need to use a TV to set up the recorder for the first time, follow the quick start guide to do so. After the initial setup, a TV or monitor is not necessary when accessing the recorder via a network connection.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

Let’s Get Started

Now that you have connected your recorder/camera to your internet router and turned it on, you will be able to view it using a program called Surveillance Client.

.

First you will need to download some software called Device Config Tool, which will allow you to find out the IP address of the camera/recorder and edit some of the settings.

.

Download it from here if you are using Windows, and here if you are using a Mac.

.

Once the software has been downloaded and installed, you will see a window like the screenshot below. Make a note of the camera/recorders IP address.

.

.

If the recorder/camera does not appear in the program, first ensure they are turned on and check the connections from the device to your internet router. If you are using a Wi-Fi bridge system, make sure that they are configured correctly (if they were not pre-configured) and are both turned on.

Surveillance Client

If you are using Windows you can download Surveillance Client from here.

.

If you are using a Mac, download it from here.

.

When you have downloaded and installed Surveillance Client you will be presented with a set-up wizard. Click Next, then Add Online Device. Your recorder/camera should appear in the list; select it then click Add Selected Device. 

.

.

Now choose a name for the recorder/camera. By default the username is admin and the password is blank. Now click ‘Add’.

.

.

You will see the device appear in the left hand pane. Select it, click ‘Import’, then open the ‘DefaultGroup’ folder on the right side and you will see it has been added.

.

.

Click ‘Next’ then ‘Finish’ and you will be taken to the main menu. Now click on ‘Main View’.

.

.

When you are taken to Main View, double click on DefaultGroup, then the name of your recorder (if you have one) and the cameras will be shown. In the screenshot I only have one camera connected, which is signified by the green play icon. Double click on the camera name to begin live view. If you want the camera to be in full screen, double click on the live feed.

.

.

To access recordings, go to back to the Control Panel and then click on Remote Playback. Open up DefaultGroup on the left side panel, then select the cameras which you would like to view recordings from and click the play button. You can select the date using the calendar on the bottom right.

.

.

To access the settings of the recorder/camera itself, go to the Control Panel, click on Group Device, then click on the spanner icon next to your recorder.

.

.

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

MORE PAGES >>>

Step 1

From the Main Menu select Account

.

Step 2

Select User ➞ Click on Add User to create a new Username and Password

.

.

Note: You cannot modify the systems defaulted User Names.

Step 3

Create a Username and Password for your new account

Select the permissions you would like the account to access

.

.

Step 4

.

If successful, you should now see your new user listed below

.

Audio Recording Setup

.

From the Main Menu, go to Camera->Encode

.

.

.

Click the More Settings option

.

.

Click Audio on, Okay and then, Apply

.

.

SCS Pro XVR full installation guide

Read More : Dahua NVR XVR Basic Setup Initial Setup

How to Setup Push Notifications via SCS Pro

.

The following guide will apply to the SCS Pro App on the iOS App Store or Google Play Store.

.

.

Start by opening the App. On the Home screen you will tap on the … next to the DVR/NVR you want to enable alerts on.

Then you will tap on Device Details.

.

.

.

On the Device Details page you will tap on Multi-channel Alarm Subscription.

.

.

.

.

Enable the alarm notifications by sliding the switch at the top of the screen.

.

Select which type of alert you would like to enable below. This example will show motion detection alerts.

Select the cameras you want to enable Motion Alerts for by tapping on the circle on the right. You can also tap on Select All in the top right if you want to enable alerts for all your cameras. Once you have made your selections tap on the back button on the top left.

Tap on Save at the bottom of the page.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.You will now be receiving alerts on your mobile device. You may need to alter your SCS Pro App settings inside of your phone or tablet to allow notifications.

Changing Camera Names

This guide will assist you with changing the name of the camera in the Live View Display.

.

First you will need to access the main menu by right clicking anywhere on the screen. Left click on Main Menu and enter your password. Then click on Camera under settings.

.

.

.

In the camera settings click on Camera Name on the left .You will see a list of all the camera channels with their default names. Click in the text box next to the camera you want to modify and type with the on screen keyboard.

.

For this example we will name the Channel TEST and then click the apply button on the bottom right.

.

You should now see the updated channel name on the Live View screen for that camera.

.

.

.

.

NOIP DDNS SETUP INSTRUCTIONS

.

Step 1

.

Go to https://www.noip.com and Sign Up for an account.

.

.

.

.

.

Make sure to Check the box “Create my hostname later” and create your account.

Step 2

.

.

Once your account is created and verified proceed to the Login Page https://www.noip.com/login?ref_url=console

.

.

.

.

.

.

.

.

.

.

.

.

Login with your account from here.

Step 3

.

Once you login you will be greeted by the dashboard, from the top left proceed to Account > Account Info page.

From the Account Info page, you will need to go to username and add a username. See Figure 1 below. This is for your device to login with later.

Once done, the NVR/DVR can be bound to the account and trace the Public IP from your Local Network and send that information to NOIP.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

Figure 1

Step 4

.

.

.

Once the account info has been configured go to Dynamic DNS > NOIP Hostnames and create a Hostname

.

When creating a hostname, you would put in the hostname spot a name or address that is easy to remember. For example, if the hostname is myhost211 and the domain is set to ddns.net when it is created it will look like “myhost211.ddns.net”

See Figure 2

.

.

Figure 2

Step 5

.

Once your DDNS is created, you can go into your system’s Main Menu > Network > DDNS page and select NOIP for the DDNS type. Then you would type in your login information to the username and password area of the system and type in the full domain name.

.

i.e., Username: (NOIP Username) Password: (NOIP Password) Domain: “YourNOIPDomain.quickddns.com”

.

If setup correctly NOIP will Dynamically update the IP as needed on its own. NOIP is a subscription service so if you do not have a subscription you will need to manually re-apply for your DDNS once every month.

.

.

.

.

To enable this on older DVR’s pre 2015 you may need to go to Settings > Network > Advance Settings > DDNS and Double click on the setting then Enable it.

.

.

With the DDNS configured on the system you will need to then port forward your router with either the TCP or HTTP ports for your system.

The Default ports that need to be opened for the Blue / Black line systems are TCP 80 for Web and TCP 37777 for the Apps.

You can learn more about Port forwarding on your router here.

How To Set Up Port Forwarding – Port Forward

With the steps above correctly setup your system will be configured to the NOIP Server.

.

.

.

.

If you have any questions or issues please contact our Support team at

support@cctvsecuritypros.com or (888-653-2288) ext 3

.

How to Reset Password via SCS Pro

.

The following guide will apply to the Blue and Black Line recorders.

If using a Blue line NVR, make sure all cameras are connected.

.

Start by Right Clicking with your mouse anywhere on the screen. Then select

Main Menu

.

.

.

.

If you previously setup a Pattern Login. You will select Forgot Pattern

.

.

On the Login Screen select the Forgot Password option on the right..

.

.

.

On the Next Page. Please read and select OK at the bottom

This is the Password Reset screen. This screen shows a QR code on the Left that you will scan with your Smartphone or Tablet using the SCS Pro App.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

Once correctly scanned with SCS Pro. The email at the bottom of your screen will receive a Security code to reset your password. Please ignore the Mobile Client QR code on the Right.