1. LAN Port and PoE Ports

Intuitively, there is one LAN port and four PoE ports in the MS-N1009-UPT.

For the LAN port, the default IP address is 192.168.5.200. You can set the local IP for the NVR via Smart Tools which you can download from the official website of Milesight. And you can log-in the NVR to manage it via web by using the IP address .

For the PoE ports, each port has a fixed number like the above picture showing. They can be directly used to connect to the Milesight cameras.

2.How to use PoE ports

For MS-N1004-UPC, the default IP address of the 4 PoE channels are 192.168.20.xx. When you activate a NVR, the NVR password will also be used to activate the PoE channels.

when you put the IP camera into the PoE port,

• 1) It can plug and play as long as its password is same with the NVR.

For example: NVR: 192.168.7.150Password: ms111111

IPC1: 192.168.7.151Password: ms111111

Plug in and refresh.

You will find that the IP address has been changed into 192.168.20.xx. And it shows .

1) When the password of the IP camera is not same with the NVR, we can make it connected through editing the exact password of the IP camera.

For example:NVR: 192.168.7.150Password: ms111111

IPC2: 192.168.7.152Password: ms123456

                    Plug in and refresh.

The password of the IP camera is not the same as the channel, so status will be shown as .

There are two ways to edit password to make the IP camera connected:

l One way:

Choose the  IP camera, and then click on “Edit Authentication”.

Milesight PoE NVR

Read Next : Milesight – How to Upgrade Firmware for IP Camera

After clicking on the button, it will pop up a window as follows. Then input the exact password “ms123456” and click on “OK”.

• The other way:

Click on the button “Edit”.

After clicking on the button, it will pop up a window as follows. Then input the exact password “123456” and click on “OK”.

After saving the password, the status will be shown as  by clicking on the button “Refresh”.

3) If the IP camera has ever been connected into the random PoE port , even if its IP address changes after being pulled out , as long as the password dose not change, you can plug in random PoE port without verifying password anymore.

On the contrary, you need to verify the password if you changed the password of the IP camera.

For example:IPC1 :192.168.20.2password: ms111111

Previously it connected in Port1.

Pull out the IPC1 and edit the IP address into 192.168.7.151, but don’t change the password.

Now put it into Port3. Just refresh, then you will find that it has been connected in Port3 without verifying password and the IP address has been changed into 192.168.20.xx.

Note:

If you have done the right steps, but you find that the state is “Disconnected”. Please keep clicking on the “Refresh” till “Connected” comes out.

3. How to configure IP camera connected via PoE

For the network cameras connected with PoE NVR via PoE ports, you can not view or configure them on web directly because the IP network segments of IP camera and your PC are different. There are two ways to solve this issue.

One way:

1) Connect PC to one of the PoE ports of PoE NVR using a network cable;

Then you can view and configure both PoE NVR and IP camera directly on web using corresponding IP address.

• The other way:

1) Enable the “ Channel Access” in Setting and saving.

Note: This setting is disabled by default.

2) Click on the “IE” button.

3) After clicking on the button, it will pop up a window as follows.

4) Input the user name and password,Then you can view and configure IP camera directly on web.

1. Choose Firmware

H.264

10.5.0.110-r11(MS-C2XXX-XX): https://drive.google.com/file/d/0B3OW8hozx4jWaXBkSDNGMXJ5V1k/view?usp=sharing

20.5.0.110-r11(MS-C3XXX-XX): https://drive.google.com/file/d/0B3OW8hozx4jWdEZTRXZJMUY4b1U/view?usp=sharing

30.7.0.63-r20(MS-CXXXX-XXA): https://drive.google.com/open?id=1oyPBRAyH4iMAKuZ26cImj1pmlgBIYcTx

H.265

40/41.7.0.XX(MS-CXXXX-XXB): http://www.milesight.com/support/download.asp

42.7.0.67-r1(MS-C8262-F(I)PB/MS-C9674-PB): https://drive.google.com/open?id=1p5RMxUuUbMTmBkKWoTTsxKvUZlQ-_72a

43.7.0.XX(MS-C81XX-XX/MS-C82XX-XX/MS-CXXXX-(Q)(T)(R)(H)XX/MS-CXX74-PB/MS-CXX65-PB): http://www.milesight.com
/support/download.asp

Load More : How to Upgrade Firmware for Milesight NVR

Note:

1) Firmwares 10.5.0.110-r11 and 20.5.0.110-r11 are separately used for cameras MS-C2XXX and MS-3XXX which are without -A or -B in the model names, such as MS-C2182-P and MS-C3366-FPN;

2) Firmware 30.7.0.63-r20 is used for cameras with -A in the model names including MS-C2XXX-A and MS-3XXX-A, such as MS-C2182-PA and MS-C3366-FPNA;

3) Firmware 40.7.0.XX is used for cameras which use the firmware that the prefix of version number is 40 or 41;

4) Firmware 42.7.0.XX is used for cameras which use the firmware that the prefix of version number is 42 (For earlier MS-C8262-F(I)PB and MS-C9674-PB);

5) Firmware 43.7.0.XX is used for cameras which use the firmware that the prefix of version number is 43 (For MS-C8262-F(I)PB and MS-C9674-PB );

If failed to get the upgrade firmware by clicking the link directly , please copy the link to browser manually;

To ensure that the firmware is fully available, the downloaded file will be a compressed package. Please manually extract it before importing to the File Path.

2. Key Steps after Downloading the Firmware

If the firmware you downloaded is 30.7.0.XX or 4X.7.0.XX, you can skip this part and directly go to 3.Upgrade Steps, otherwise please read below steps carefully.

Step1: If the current firmware version of your camera is above XX.5.0.85, like 10.5.0.89 or 20.5.0.90, you can go to 3.Upgrade Steps and upgrade your camera directly;

Step2: If the current firmware version of your camera is below XX.5.0.85, like 10.5.0.73 or 20.5.0.80, you should change the name of the firmware you downloaded according to the table below;

Take MS-C2651-PM for example:

Step1: According to the table above, it matches with MS-C2XXX, so we should download MSFImage_10.5.0.110_896a6b5b first.

Step2:

1) Suppose that the firmware version of this camera is XX.5.0.87 before upgrading, we can directly upgrade it according to 3.Upgrade Steps;

2) Suppose that the firmware version of this camera is XX.5.0.79, we should change the name of the firmware we downloaded. According to Table2, MS-C2651-PM belongs to model MS-C26XX and matches with 11.X.X.XX. So we need to change MSFImage_10.5.0.110-r11_2e653e10 into MSFImage_11.5.0.110-r11_2e653e10

3. Upgrade Steps

Please check each model with right firmware version as mentioned above , then upgrade the firmware according to the following steps:

Step1: Go to the web of IP Camera, click “Configuration” -> “Maintenance” -> “Upgrade Firmware”

Step2: Browse and select files for the upgrade.

Step3: Click the “Upgrade” button and a progress bar will pop up, wait for about 1-3 minutes until it reaches 100%. After that, the system will reboot, and the firmware upgrade successfully.

Step4: Use Milesight Smart Tools to search out this camera according to its MAC address, and then change its IP into your local IP address. (The IP address will be kept after upgrading if the firmware versions are after XX.4.0.52).

You can also use Smart Tools to download the latest firmware.

“IPC Tools”-“Upgrade”-“Firmware Online”

The link for Smart Tools:

http://www.milesight.com/DownloadFile/Software/Smart_Tools/Milesight_Smart Tools_Setup.zip

Note:

1) If the current firmware version of the camera is below 10.5.0.73 and 20.5.0.73, like 10.5.0.68 or 20.4.0.51, please reboot the camera and restore it into factory settings via web before upgrading.

2) For the new version, you may need to re-install the ActiveX. During the installation, please close the browser, otherwise the ActiveX may not be installed correctly.

3) Please clear the cookies first after re-installing the new ActiveX(Press Shift+Ctrl+Delete to quick call the clear cookies windows).

1. Choose Firmware

4K Series

71.X.0.X(MS-N50XX-UH/MS-N70XX-UH/MS-N70XX-UPH/MS-N80XX-UH): http://www.milesight.com/support/download.asp
72.X.0.X(MS-N1009-UNT/MS-N1009-UPT/MS-N50XX-UT/MS-N50XX-UPT): http://www.milesight.com/support/download.asp
73.X.0.X(MS-N1004-UC/MS-N1004-UPC): http://www.milesight.com/support/download.asp

Previous Versions

61.7.0.7-r5(MS-N1009-UT): https://drive.google.com/open?id=0B8u2Oc2-fG-mc0dCR3paYzNKMGs

30.7.0.7(MS-N5009/5016): https://drive.google.com/open?id=0B3OW8hozx4jWT182aXBfMGxGUGs

31.7.0.7(MS-N1004/1008): https://drive.google.com/open?id=0B3OW8hozx4jWd2FhTmk0cWJmNFk

2.7.0.7(MS-N5004/5008): https://drive.google.com/open?id=0B3OW8hozx4jWY3lmOF8takNQWnc

1.7.0.7-r3(MS-N7016/8016/8032): https://drive.google.com/open?id=0B8u2Oc2-fG-md0pwOFJMM3V4X2c

Note:

1) The second number of firmware stands for major version number, while the last two number means the minor version number. Take 71.7.0.5 for example, it means that the NVR’s major version is 7 and it’s minor version is 5.

2) You can use monitor to upgrade your NVR, or you can upgrade it via browser. If click the link to get the upgrade firmware failed, please copy the link to browser and open again.

3) If the firmware of your MS-N1009-UT begins with 61.X.X.X, or the SN begins with 12xxxxxxxxx, then use the 61.X.X.X.

If your MS-M1009-UT firmware begins with 71.X.X.X, or the SN begins with 13xxxxxxxxxx, then use the 72.X.X.X.

2. Steps for Monitor

Step1: Enter upgrade menu by clicking “Main Menu”→“System Settings”→“Upgrade”.

Step2: Search for the device you downloaded in your USB, and select the file.

Step3: Click “Upgrade” button to confirm the upgrade.

Note:

The system will be automatically rebooted after being confirmed upgrade.

3. Steps for WEB

Step1: “Settings”→“System”→“Maintenance”.

Step2: Click “Browse” and find the position where you downloaded.

Note:

Remember to check the model, use the corresponding firmware for your model.

Step3: After choosing the corresponding firmware, click “Upgrade” button to confirm the upgrade.

Note:

The system will be automatically rebooted after being confirmed upgrade.

4. Steps for SmartTools

Step1: Use Milesight Smart Tools to search out this NVR according to its MAC address.

Step2: Click “Browse” and find the position where you downloaded.

Step3: After choosing the corresponding firmware, click “Upgrade” button to confirm the upgrade.

Note:

You can also use Smart Tools to download the latest firmware.

“NVRTools”-“Upgrade”-“FirmwareOnline”

The link for Smart Tools:

http://www.milesight.com/DownloadFile/Software/Smart_Tools/Milesight_Smart Tools_Setup.zip

MIP Milesight Plugin

Milesight M-Sight Pro (Android)

Milesight CMS (for Mac)

Milesight CMS

Milesight Smart Tools (for Mac)

Milesight Smart Tools

4K Series

71.X.0.X(MS-N50XX-UH/MS-N70XX-UH/MS-N70XX-UPH/MS-N80XX-UH): http://www.milesight.com/support/download.asp
72.X.0.X(MS-N1009-UNT/MS-N1009-UPT/MS-N50XX-UT/MS-N50XX-UPT): http://www.milesight.com/support/download.asp
73.X.0.X(MS-N1004-UC/MS-N1004-UPC): http://www.milesight.com/support/download.asp

Previous Versions

61.7.0.7-r5(MS-N1009-UT): https://drive.google.com/open?id=0B8u2Oc2-fG-mc0dCR3paYzNKMGs

30.7.0.7(MS-N5009/5016): https://drive.google.com/open?id=0B3OW8hozx4jWT182aXBfMGxGUGs

31.7.0.7(MS-N1004/1008): https://drive.google.com/open?id=0B3OW8hozx4jWd2FhTmk0cWJmNFk

2.7.0.7(MS-N5004/5008): https://drive.google.com/open?id=0B3OW8hozx4jWY3lmOF8takNQWnc

1.7.0.7-r3(MS-N7016/8016/8032): https://drive.google.com/open?id=0B8u2Oc2-fG-md0pwOFJMM3V4X2c

Note:

1) The second number of firmware stands for major version number, while the last two number means the minor version number. Take 71.7.0.5 for example, it means that the NVR’s major version is 7 and it’s minor version is 5.

2) You can use monitor to upgrade your NVR, or you can upgrade it via browser. If click the link to get the upgrade firmware failed, please copy the link to browser and open again.

3) If the firmware of your MS-N1009-UT begins with 61.X.X.X, or the SN begins with 12xxxxxxxxx, then use the 61.X.X.X.

If your MS-M1009-UT firmware begins with 71.X.X.X, or the SN begins with 13xxxxxxxxxx, then use the 72.X.X.X.

2. Steps for Monitor

Step1: Enter upgrade menu by clicking “Main Menu”→“System Settings”→“Upgrade”.

Step2: Search for the device you downloaded in your USB, and select the file.

Step3: Click “Upgrade” button to confirm the upgrade.

Note:

The system will be automatically rebooted after being confirmed upgrade.

3. Steps for WEB

Step1: “Settings”→“System”→“Maintenance”.

Step2: Click “Browse” and find the position where you downloaded.

Note:

Remember to check the model, use the corresponding firmware for your model.

Step3: After choosing the corresponding firmware, click “Upgrade” button to confirm the upgrade.

Note:

The system will be automatically rebooted after being confirmed upgrade.

4. Steps for SmartTools

Step1: Use Milesight Smart Tools to search out this NVR according to its MAC address.

Step2: Click “Browse” and find the position where you downloaded.

Step3: After choosing the corresponding firmware, click “Upgrade” button to confirm the upgrade.

Note:

You can also use Smart Tools to download the latest firmware.

“NVRTools”-“Upgrade”-“FirmwareOnline”

The link for Smart Tools:

http://www.milesight.com/DownloadFile/Software/Smart_Tools/Milesight_Smart Tools_Setup.zip