Hikvision NVR 5.0 Professional Installation Guide

Hardware Installation

Software Configuration

Additional Resources

Important Note: The provided steps serve as a general guideline. Specific configurations might differ based on your NVR model. Always refer to the official user manual for detailed instructions and advanced functionalities.

Setting up a Hikvision NVR (Network Video Recorder) involves several steps, including hardware setup, network configuration, and camera configuration. Here’s a detailed guide to help you set up your Hikvision NVR 5.0:

1. Hardware Setup

Step 1: Unbox and Connect Components

Step 2: Connect the NVR to a Monitor

Step 3: Connect the NVR to the Network

Step 4: Connect Cameras to the NVR

Step 5: Power Up the NVR

2. Initial Configuration

Step 1: Boot Up and Log In

Step 2: Set Date and Time

Step 3: Network Settings

3. Adding Cameras

Step 1: Detect and Add Cameras

Step 2: Configure Camera Settings

4. Recording Settings

Step 1: Set Up Recording Schedule

Step 2: Configure Storage Settings

5. Remote Access Setup

Step 1: Enable Hik-Connect

Step 2: Port Forwarding (if necessary)

Step 3: Mobile App Setup

6. Final Steps

Step 1: Test the System

Step 2: Backup Settings

Troubleshooting Tips

This guide should help you set up your Hikvision NVR 5.0 system. For more detailed instructions, refer to the user manual or the Hikvision support website.

.

Our IP camera can connect directly to your network or computer, and there are three ways to do so. The three ways listed below do not require a NVR. A NVR, or Network Video Recorder, is the device that IP cameras connect to.  The NVR records video provided by the IP cameras to a hard drive, either in HD (720p, 1080p), 2K HD, or Ultra HD (4K) depending on the type of NVR and type of camera that’s being used with it.

IP cameras are network-based cameras, however they don’t require Internet access in order to be used as they are standalone devices that can be used on a local network. A simple local network can be either of the following:

1.An IP network camera connected with a network cable to your desktop computer’s network port.

2.An IP camera connected to a router that is connected to a desktop or laptop computer, but the router is not connected to the internet.

Only if you want to view your system remotely from the internet then you would have to connect the system to the Internet.

Do I need a NVR for my IP security camera system?

A NVR is not necessary in order to view your network cameras or even record video. If you are testing cameras, looking for a temporary setup or want to set up something inexpensive then using a computer with an IP camera is a good alternative to a NVR.  SmartPSS is our computer software program that allows PCs to view and record IP cameras. However, this kind of processing will demand a lot from the computer. Most likely, you wouldn’t be able to use that computer for personal use as it would be bogged down processing video from high resolution IP network cameras.  Also, computers can be unreliable and crash, potentially leaving you with no recorded video.

NVR products are standalone devices using a Linux operating system which is known to be rock-solid and crash free, and designed to be operate 24/7 and maintain system security with user account access permissions. For a complete security camera system, you will want to use a NVR along with cameras. SmartPSS software can be used as a client software to connect from a computer to a NVR to watch cameras connected to the NVR and to playback/download recorded security footage.

How to Connect IP Camera Guide 2024

Three ways to connect an IP camera to a computer

Before we begin, it is important to understand that network camera systems require the ability to transport video and power to work correctly. Power Over Ethernet (PoE) is a technology that transmits video/data signal and power over one Ethernet cable. In situations where PoE isn’t available, a 12V DC power adapter will be necessary to supply power to the camera.

Secondly, you will need to use our IP finder Config Tool to find cameras on your network. For more info on basic networking knowledge as to how IP addresses matter when deploying network cameras, please read our guide about connecting security cameras to the internet.

Now, let’s discuss the three ways to to connect to an IP camera from your computer.

1.12V DC power adapter with a network cable straight into a PC

2.12V DC power to camera + network cable to router

3.Camera to PoE Switch or PoE Injector

How to Connect IP Camera to Computer

1) 12V DC power adapter with a network cable straight into a PC

a) For this method we will provide power to the camera using a 12V DC 1amp power adapter that plugs into a 110V AC outlet. Below is a picture of our trusty power adapter.

b) Next, connect a network cable from the camera to your computer.

c) Set your computer’s network port to a static IP address like 192.168.1.200 so you can talk to the camera. Here’s how you do it on a Windows Computer:

d) All newer cameras with firmware from 2018 and onward have stringent password rules that require initialization before making any configuration changes to the camera including the IP address. In order to set the password and password recovery email address you must login to the web interface of the camera. Be sure to note down and keep the credentials you are setting in a safe place that you will remember.

There are no master reset passwords for our equipment. If you forget your password, recovery email address, and security questions that you set on the camera at time of initialization, resetting the camera requires factory service which will incur out-of-warranty costs to reflash the camera.

.

e) Once you have a static IP address assigned to your computer’s wired network port, turn off WiFi on your computer. You can find the camera’s current IP address by using the Config Tool as shown. Our test camera has a current IP address of 10.1.1.65. If you need to change the IP address to let’s say 192.168.1.120, you can do that by clicking on the pencil icon to edit.

Note: if you have a password other than admin set on the cameras, then you will need to enter that in the “search settings” options before attempting to edit the IP address. See the illustration below on how that is done.

f) As explained in our article connecting security cameras to the internet, for two devices on a network to talk to each other, they must have the same IP address scheme. In 1C we set our computer’s address to 192.168.1.200, so we need to set change this camera’s address to 192.168.1.X where X is a number between 2 and 254, and not same as the our computer’s current address. We picked 12, so below is a screenshot of what to set your camera’s ip address to if you are following along in our guide. Set the subnet to 255.255.255.0 and gateway to 192.168.1.1.

g) After changing your camera’s IP address to one that matches your network, type the new IP address of your camera into the URL of internet explorer. Here’s a brief example:

You can also view the camera using our PC software. If you don’t already have it, you can download SmartPSS from here. Here’s how if you already have SmartPSS installed.

In summary, the above is a quick and easy way to connect an IP camera to a computer with a hardwired network port. This is great for the following scenarios:

• You don’t have a router and want to set up a closed circuit system between a computer and a security camera.

• You are trying to test an IP camera or troubleshoot it.

• You are trying to connect to a security video recorder directly from a computer.

Most computers have only one network port, so this method can be problematic as it would use up your only network port, preventing you from having a hard-wired Internet connection. The next 2 methods will demonstrate how to set up a network camera on a network. Method 2 is for setting up a camera with a 12V DC power supply and Method 3 entails using a PoE injector or switch. The only different between these two methods is how power is supplied to the camera.

2) 12V DC power to camera + network cable to router

This method will show you how to connect an IP camera to your router and view it over a network, while supplying power to the camera using a 12V DC power adaptor.

a) Connect a 12V DC power supply to your camera and connect the power adaptor to the wall to power the camera.

b) Connect a network (Ethernet) cable from the camera to the router to establish a data connection between the camera and the router.

c) Give the camera about 2-3 minutes to boot. Use our IP Finder Config Tool to find the camera on your local area network (LAN).  Below is a screen shot of how it looks in our case.

The camera currently has an IP address of 10.1.1.65. As explained in our article connecting security cameras to the internet, for the camera to be reachable from the computer on your network, its IP address has to match the IP scheme of your network. In our case our router IP is 192.168.1.1, so we are going to have to change the IP address of the camera. To change the IP simple press the pencil icon to edit.

d) We are going to set the camera to an IP of 192.168.1.X, we chose 192.168.1.12. Before we go ahead and change the IP address, we have to think about duplicate IP addresses on the network which would create networking issues. To see if a specific IP address is available on your LAN, use the command prompt in Windows to ping the address you intend to use. Below is a video explaining how to use the ping command. You can use this command on Mac as well by using the terminal.

e) Let’s change the IP address. In our case we set it to 192.168.1.12. Subnet mask is usually 255.255.255.0 on simple networks, and the gateway is the IP address of the router. Press OK.

f)  Once the camera is assigned a new IP address, you can access the camera using your Web Browser or SmartPSS as shown in 1F above.

3) Camera to PoE Switch or PoE Injector

We discussed that PoE supplies power to the camera, so a 12V power adapter is not necessary in this scenario.

In this method you plug an ethernet cable from the camera to a PoE port on a compatible PoE switch or injector. The PoE switch or injector connects to the router.

Here’s how you connect to a PoE switch.

Here’s how you connect to a PoE injector

Again, use the Config Tool to find your camera’s IP address and change it to match your network scheme (if necessary) as described in steps 2C thru 2E. Once the camera is on the same network as your computer you can login and watch the camera as shown in Step 1F.

.

Summary

At this point, you now should know a good amount about networking and have used the above mentioned steps to make your very own IP camera system using your computer and IP camera.

Viewing an IP Camera on a Smart TV

Among the many different ways that security cameras are used, we are often asked if it is possible to view an IP camera directly on a Smart TV without using a NVR recorder. With most Smart TVs on the market there is no application that is available to watch IP cameras directly on the TV. In this guide we show how to use an Android TV box by downloading an App to connect an IP camera to a Smart TV or any monitor that has an HDMI input.

All IP cameras from CCTV Camera World support a RTSP video stream that is usable by third party programs and apps. The App that we suggest you use on an Android TV box is called VLC Media Player. You can login and access the RTSP stream from an IP camera and have it display on a TV.

Keep in mind any device that can download VLC Media Player can do this process like iPhones, iPads, Android tablets, and phones.

What equipment is needed?

Here’s the list of all the equipment that is needed to connect an IP camera to a Smart TV.

1.IP camera from CCTV Camera World

2.PoE injector or 12V DC Power Adaptor to power the camera

3.Network cables to connect the camera to your computer network

4.Android TV Box from any online shopping marketplace

5.Computer network to connect the camera and Android TV Box

6.Internet connection to setup and install Apps on the Android TV box which can later be removed after the setup process is finished

7.SmartTV or Computer Monitor with HDMI input

.

How to connect IP security cameras to an Android TV Box

Before you can access the stream from the camera you will need to have it connected to your computer network and verify that it’s accessible. If you purchased a standalone IP camera from CCTV Camera World the camera is likely already configured with an IP address. Check the top of the camera box for the login information label. If the camera has not been configured, or you need to set it up on your network we recommend following our How to Connect an IP Camera guide.

You will also need to set up your Android TV box on your network, consult with the manufacturer of your box to find out how to do this.

You will need your IP address, username, and password that is set on the camera in order to access it. Inside of the VLC Media Player app you can access network streams. Inside of the app navigate to adding a video source and select network stream. Using the example RTSP stream below plug in the information for your camera’s IP address and type the text into the media player URL.

rtsp://192.168.1.109:554/cam/realmonitor?channel=1&subtype=0

After you’ve typed in the correct RTSP stream for your camera you will be required to login to your camera stream. Type in the username and password for your camera to allow the app to login to your camera stream.

If you receive an error, double check that your camera is connected to the network and you’ve typed the correct username and password. Provided the camera is set up on the network and you are able to login you should now see your camera stream inside of the VLC Media Player App.

Keep in mind that Smart Camera features cannot be used with the RTSP stream. If you would like to use Smart Detection features that your security camera may have, you will want to use an NVR to display the camera on your TV.

Watch our video below that shows the setup process described above on an Android TV box.

.

.

Unlimited Access Anywhere, Anytime

When you combine our “Blue Line” IP Cameras with one of our compatible IP camera network video recorders you can keep an eye on your assets no matter where you are. Take advantage of the free remote viewing app to view on your cell. Use the free software to view and control you cameras on your tablet, or computer. Stay connected and have peace of mind knowing you can monitor your cameras remotely, without any additional monthly fees.

LATEST FIRMWARE UPDATES FOR YOUR DEVICE

UPDATING YOUR SECURITY CAMERA FIRMWARE

Firmware Updates

In order to do a firmware update you must first identify the EXACT model number of your DVR or NVR unit. The model number can be found on the sticker located on the bottom or side of the unit. All CCTV Security Pros model numbers begin with the prefix “CSP” (Example, CSP-XXXX). Please match your model number to the list provided below. You will also need to locate your order confirmation email to determine when the unit was purchased. Once you have identified the correct model number and firmware please continue by following the instructions below.

Blue Line IP Camera Troubleshooting v2

Upgrading Your Firmware

Please identify the correct model from the list of firmware provided below.

Please select the appropriate link and download the .bin file. Once the download is completed copy the .bin file to a USB Flash/Thumb Drive. We suggest formatting your USB drive to FAT32 before attempting the update.

**Note : Units with Build Dates of 2013 or earlier may require you to rename the file to “update.bin” before launching the upgrade.

Once the .bin file has been transferred onto your drive you can insert the USB Drive into either of the two USB ports found on your unit. One can be found on the front panel and one can be found on the rear of the unit.

Once the drive is inserted into the unit go to the following menu:

Main Menu –> Setting –> System –> Upgrade. Click Start. Find and select the .bin file you transferred to the USB Drive and Click Start.

*NOTE – On select models you will need to go to:

Main Menu–> Info –> Version –> Upgrade

The unit will now begin upgrading to the latest Firmware Revision that is available for your device. Once completed the system will reboot. After the reboot we recommend doing the following:

1) Remove the USB Drive from your system.

2) Change your passwords on your “admin” account. For assistance in altering your password please follow this link: https://www.cctvsecuritypros.com/content/pdfs/password-account-settings.pdf

.

IMPORTANT: If you are having difficulty identifying the correct firmware please email us at support@cctvsecuritypros.com with your order number and unit model number.

User Account Locked

Your system will lock itself out when you or someone else has attempted to log into your DVR

with an incorrect user/password combination more than three times within 30 minutes

When this happens you have two options.

1. Wait 30 minutes after the last failed login attempt and try again.

2. Reboot the DVR by using the rear toggle switch or by unplugging.

When the unit powers back on try and login with the default username and passwords.

Username: admin

Password: admin

or

Username: 888888

Password: 888888

If neither of these passwords get you into your system you will need to email us at

Support@CCTVSecurityPros.com

and request a Master Password. Once we can confirm your

account we will happily be able to provide you with the correct login credentials.

Please have your Order Number or DVR/NVR Model Number when requesting a Master

Password.

*Note: The DVR/NVR Model Number can be found on the Bottom or Side of your system.

.

IP Camera Harness Repair

If your connector looks like the ones below, moisture has gotten into your RJ45 connector. The number one cause of premature IP camera failure has to do with improper weatherproofing techniques. If caught early enough a simple cotton swab and rubbing alcohol will clean that connector right up! You may need to resort to some heavier duty electrical contact cleaner if the cotton swab method does not work.

If all else fails and the connector is too far gone and cleaning it will not work, you will need to perform a harness repair.

.

In order to perform the repair you will need:

.

.

1 x RJ45 Crimp Tool1 x Male RJ45  1 x Female to Female RJ45

Connector

.

1 x Your choice of weatherproofing ( Weatherproof junction box or weatherproof Female to Female connection)

.

.

Start by removing the RJ45 end off of your IP cameras harness. Be sure

.

Strip back the outside insulation to expose the internal cables.

.

Organize the cables to match the pinout of the IP camera. Slide the organized cables into the connector and crimp. All CCTV Security Pros IP cameras will use this pinout.

Connect your Female to Female RJ45 connector to check your work, you should have a functioning IP camera now that its void of all corrision.

Now that the IP camera has been repaired we still need to weatherproof this connection. It is now more vulnerable than ever!

Consider using a weatherproof junction box to make your connections in, or perhaps a weatherproof Female to Female connector.

Remember that different coupling styles exist so make sure that you are informed about how to use the coupler before you start crimping wires.

Troubleshooting Steps 4/8/16 Channel

(Cannot Find the Network Host)

To solve the error, please verify that the camera is properly plugged into the back of the system. If you unplug and re-plug it back in this should verify it is connected physically.

If the issue continues go to Main Menu > Camera > Camera List and delete the camera with the red status from the bottom list and do a Device Search to verify the camera is showing up on the top list.

If the camera does not show up this means the cable is not connecting properly, which could either mean the camera is not getting power or isn’t transmitting data. The best way to determine whether it is an issue with the Camera or Cable is to bench test the camera on a known working cable.

If it does show up but it has a different IP Address, please confirm the IP Address is in the 10.1.1.1-255 range (This is the default range of the internal Switch).

If the camera is not within the correct IP range, then the camera could need to be modified on the top list to properly connect in which you would select the camera, hit modify, type in the camera’s username and password and set the IP address to DHCP to automatically obtain an IP or statically assign the camera an IP address to match your switch range and gateway.

If the camera is on the correct range, you should be able to add it to the bottom list and it will come up with Green or Red, If Red double check the error message on the live view on the system.

If the Error says Invalid Username or Password, go back to Settings > Camera > Camera List and modify the camera at the bottom of the list and type in the correct login information.

If the error says Cannot Find the Network Host, check the IP Address is in the correct range, if it is you need to verify your cable is good by testing the camera with another known good cable or testing on a short patch cable as the cable could be experiencing packet loss.

Make sure the cable is T568B Standard and is within 100 meters (328 feet.)

Night Vision Issues

When a camera goes into night vision mode, the infrared LEDs around the lens turn on. If the video signal at nighttime or in dark locations is washed out, foggy or you see “halos” on the screen it is because the infrared LEDs are reflecting back into the camera lens.

cameras LEDs to focalize on the mounting surface and greatly reduce the Infrared distance.

Adding 3rd Party Cameras to Blue Line NVR

We always recommend using Blue Line IP cameras with our Blue Line NVRs for the easiest and most complete experience possible. However, we understand that using 3rd Party Cameras can be beneficial in some applications. This guide will explain the basics of adding a 3rd Party IP camera into your Blue Line NVR.

Information you will need to add 3rd Party Cameras.

With your camera attached to one of the PoE ports on your NVR, you’ll navigate to the camera settings from the main menu.

A 3rd Party Camera normally will not add itself, so you will need to go into the Camera List and click on Search Device. If the camera is detected, you will be able to select it and click on the Modify IP button toward the middle of the screen.

When modifying the IP address of the camera the default IP range for the PoE ports on the NVR is

10.1.1.xxx so you’ll want to make sure the camera is on the same range.

You will need to know the camera’s password to change the IP Address. Once the IP is successfully changed it should update after clicking Search Device again

Check the box to the left of the camera and click Add. Most cameras will show up with the Manufacturer as ONVIF. If they do not and show up as red, you will need to click on the edit button on the camera and change the Manufacturer to match the camera’s manufacturer, or to ONVIF if the manufacturer of the camera is not listed.

While in the modify window you can also enter the password for the camera in the password field. Once that is completed you can click OK. After a few seconds the status should change to a green icon and then you should be able to see the camera’s live view. Please keep in mind that if the Error Message says Invalid Username or Password you may need to login to the camera from the Web and setup an Onvif User for the system to login with.

If the camera is still showing offline, setting the manufacturer to PELCO can sometimes resolve the issue.

Additional 3rd Party Camera Information

DVR/NVR Rebooting

If your DVR or NVR is rebooting by itself please read the guide below.

If your DVR or NVR is rebooting once a week this is completely normal. Our DVR and NVR systems are designed to reboot once a week (Tuesday at 2AM by default).

If your DVR or NVR is rebooting more frequently you first want to check the power source of the DVR or NVR.

Be sure you are using the correct Power Source that was included with the DVR or NVR. Below are the correct power adapter specs so you can identify the correct one.

NVRCUBE = 12V, 2.0Amp NVRWIFI = 12V, 2.0Amp

LITE Series DVR = 12V, 2.0Amp

Pro Series DVR = 12V, 5.0Amp

Pro Series NVR = 3 Prong Power Cord to Power Outlet Extreme Series DVR/NVR = 3 Prong Power Cord to Power Outlet

If you can confirm you are using the correct Power Adapter you may need to double check the outlet you are plugged into. Try an alternate outlet and eliminate any Battery Backup Power Supplies for test purposes.

If the power source is not causing the reboot cycle it could be related to the internal hard drive. To check this out please continue reading.

First you will need to Power Off the DVR. We suggest powering the system down from the Power Switch on the rear of the system or by simply unplugging the Power Cable.

Once the system has been powered down you will need to open up the system. Please see below to locate the screws that need to be removed.

NVRCUBE or NVRWIFI

There will be 4 Phillips head screws located on the bottom of the system. Once the screws are removed the top cover will lift off.

Lite Series DVR

There are 2 Phillips head screws located in the rear and 2 on the side of the DVR, 1 on each side. Once the screws are removed the top cover will lift off.

Pro Series DVR/NVR

There will be 4 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Extreme Series DVR/NVR

There will be 2 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Once the top cover has been removed it will expose the Hard Drive and its connections.

First we want to Unplug the Large Black Connector. Press down on the metal tab and pull the connector out of the Hard Drive.

Now we want to unplug the second smaller connector (Blue Cable) from both ends. Press down on the tab and remove from the Hard Drive as well as the System Board.

Once the connections have been disconnected. Plug them back in securely and listen for the metal tab to click. This will ensure a good connection in between the System Board and Hard Drive.

Note*

While you still have the system open, it might be a good idea to check the cooling fans for any dust or debris that could be stopping the fan from moving. This could cause the DVR or NVR to overheat.

Once the connections are tight, lets put the top cover back on. When the cover is back on you can proceed to power on the system. Once the system is powered on you will need to monitor the system and check if it is still rebooting.

Disconnecting The Internet

If the system is still rebooting you may want to disconnect it from your Router or Modem by unplugging the Ethernet cable in the rear. You will loose your remote viewing capabilities temporarily while unplugged but can help us diagnose the issue.

With the cable unplugged you may want to monitor the system closely to see if this has made any changes to the rebooting issue.

Disconnecting Cameras and Other Sources

Disconnecting cameras, alarms, extra monitors and microphones is the last thing we can try to solve your rebooting issues.

Cameras, monitors, and microphones mounted near high voltage could be causing your system to reboot by itself. If your system detects any incoming voltage or amperage coming into the rear inputs the system will shut down to protect itself from damage.

Leave your main Display Monitor and Power Source connected. Disconnect one input at a time to see if it makes a change in your reboot cycle. If you notice a change in the rebooting you can single it out by using this method of elimination.

Get Started with Verkada Intercom Set up and connect your Verkada intercoms Updated over a week ago

Required. You need Org Admin and/or Site Admin permissions for your Verkada Command organization to complete these actions.

What you need

Create a site

Sites are the logical way of grouping and managing devices within your Command organization. Site-level permissions make managing and viewing your devices easier. See Manage Your Sites and Subsites for more information on site creation and management.

Add an intercom

At least one intercom needs to be added to Command before you can see the Intercom tab in the All Products menu. Intercoms can be added to Command from the Devices page. See Add an Intercom to Your Site for more information.

Connect a door

You can pair an existing access-controlled door or wire a door to the intercom that can be unlocked by an intercom receiver. See Configure a TD52 and Wire a TD52 Video Intercom for more information.

Configure receivers

Receivers allow you to answer calls from an intercom and unlock any associated doors. See Add and Configure Receivers in Intercom for more information.

Licensing

Every intercom you manage in Command will need a license. Verkada licensing is applied for each Command organization, and the licenses co-term to a single expiration date. Your licenses may have been automatically added if you claimed your devices via order number. Otherwise, manually add the licenses from the Admin page. See Manage Your Licenses for more information on adding and managing licenses.

Connect your intercom

Recommendation. While Verkada intercoms are considered low-voltage devices that do not require a certified electrician to install, we strongly recommend you work with a system integrator or other professional for installation.

Please refer to the intercom setup guide for instructions on mounting and wiring the door port.

Power and network

Verkada intercoms use Power over Ethernet (PoE) for power and communication over the LAN. In most cases, intercoms will connect directly to an 802.3af PoE standard switch. PoE injectors can be used when a PoE switch is not available. See the intercom’s datasheet for more information.

Check network settings

Verkada intercoms are designed to be plug-and-play. However, if your environment includes a firewall with custom rules and policies, you may need to make some configuration changes to get your access controllers connected to the cloud. See Intercom Network Settings for more information.

Roles and Permissions for Intercom

Roles and Permissions for Intercom

Learn more about Verkada Intercom roles and permissions

Updated over a week ago

This article describes the set of roles and associated permissions for Verkada Intercom.

Verkada intercoms setup guide v1

Verkada Intercom permissions determine who can receive calls, view intercom video, and unlock intercom doors. Intercom permissions depend on your site-level permissions, and whether you’re configured as a Receiver.

At a high level, these are the permissions granted to each level of Intercom devices:

Site-level roles

Receiver

Required. You must be configured as a receiver to receive calls.

If you’re a Verkada Intercom Receiver, you have the baseline receiver permissions (as shown above). These baseline Receiver permissions combine with site-level permissions to determine overall intercom permissions within a certain site.

For example, if you’re a Receiver for a particular intercom, and a Site Viewer, you get all the Receiver permissions, in addition to the ability to view historical video and events.

Note: Receivers, such as Desk Stations and Session Initiation Protocol (SIP) phones are not tied to a Verkada Command user. This means that the user can only get Receiver permissions, regardless of the user’s site-level permissions.

Regardless of their site-level permissions, a Receiver can:

Live-View Only

Site Viewer

Site Admin

.

Verify a user’s eligibility to receive Verkada Pass calls

.

Set Org Admin permissions

Revoke Org Admin permissions

.

Set site and subsite permissions

You can set site and subsite permissions by adding a user, a group, or by existing users and groups.

Add a user

Add a group

Existing users and groups

You can set the site and subsite permissions for existing users and groups by managing the user roles or the sites.

Manage roles

Manage sites

Intercom Network Settings

Intercom Network Settings

Learn about the required network settings for Verkada Intercoms

Updated over a week ago

This article outlines the required network settings that your Verkada Intercom needs to communicate with Verkada Command. For more information on the required network settings for other Verkada product lines see Required Network Settings.

Note: Verkada devices are incompatible with LANs that require proxy servers or Secure Socket Layer (SSL)/Transport Layer Security (TLS) inspection. If either is in use, a bypass for all Verkada devices must be implemented for Verkada devices to communicate with Verkada Command.

Status LED

A flashing blue status LED on the top of the intercom indicates the intercom is not communicating with Command. If you see this behavior, check that the network is set up correctly with the intercom’s requirements. If the problem persists, contact Verkada Support.

IP address

Intercoms must be assigned an IPv4 address to communicate on the LAN and to Verkada Command. Intercoms use Dynamic Host Configuration Protocol (DHCP) and User Datagram Protocol (UDP) to obtain their IP addresses and network configurations.

If you require your intercom to have a specific IP address, create a DHCP reservation using the device’s Media Access Control (MAC) address (found on the device’s label).

Domain Name System

Intercoms use the DNS server to resolve Verkada’s fully qualified domain names (FQDN) to IP addresses to communicate with them. Your DHCP server tells the intercom where the DNS server is on the network and the intercom communicates using UDP port 53.

Note: DNS over HTTPS (DoH) is currently not supported.

Power

Intercoms are powered through Power over Ethernet (PoE). This means the network switch needs to provide power to the intercom, or a PoE injector needs to be utilized. For specifics on power requirements, see the Intercom datasheet.

Firewall settings

Intercoms require access to many endpoints to ensure they can communicate with Command and all features will be accessible. Many customers may want to allow the intercoms to communicate with the general required endpoints.

These are the general domains to allow, applicable for all organization-regions:

Region: United States

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Region: Europe

Standard Verkada Endpoints

NTP Endpoints

Streaming Endpoints

Calling Endpoints

Access Control Endpoints

Cloud Backup Endpoints

Mount a TD52

Mount a TD52

Learn how to mount the Verkada TD52 Video Intercom

Updated over a week ago

Use this article to learn how to mount a Verkada Intercom (TD52). Once you complete the mounting, you can connect the TD52 to the network.

Before you begin

You can mount the TD52 using a flush mount or using a mounting bracket. We recommend that you verify the contents of your box and make sure you have the tools you need

Contents of your box

Tools you need

Choose your mounting option

Whichever mounting option you choose, you should remove the front cover of the TD52 to access the screw holes that allow you to install on a mount.

Use a flush mount

The TD52 comes with a flush mount in the box. You can use the screw holes of the flush mount to mount the Intercom (see image below for visual):

Mount directly to a wall

Use a mounting bracket

You can use the mounting bracket to install the TD52 on to various surfaces that the flush mount plate cannot, where they’re typically used to mount the TD52 on an exterior surface.

<< Click on the page numbers to go to other pages. >>

This guide explains the setup for each option so that you can determine which one is best suited for your needs and scene..

How to find the camera’s light settings in its web interface:​

Even if the camera is connected to an NVR, before anything, you will need to log into the camera directly to access the advanced image and light settings to enable the different light modes, as these are not accessible from an NVR.
.

By default, your camera will be set to remain in ‘ColourVu only’ mode during low-light, meaning the white light will be constantly on when it is dark and never use its IR. The below sections will show you on how to configure the new ‘Smart Hybrid’ mode, ‘IR only’ mode, and ‘ColorVu only’ mode.
.

.

How do I set my camera to Smart Hybrid mode:​

This mode is utilises both the IR and white LEDs built into your camera. It is useful as it allows you to keep your cameras to stay discreet in IR mode while there is no activity in your scene, and then switch to full colour when a person or vehicle is detected by putting white light on the scene, providing you with all of the additional information a colour image offers while also acting as a deterrent.

Here are the steps to enable this mode:
.

.

How do I set my camera to ‘IR only’ mode:​

This mode is recommended if you would like the camera to be as discreet as possible and your scene is dark at night, as the camera will use its IR LEDs all the time at night and then switch back to colour during the day, meaning the white light is never used.
.

How to Configure Light Settings on Hikvision Cameras

How do I set my camera to ‘ColorVu only’ mode:​

This is the opposite to IR mode, as the camera will turn on its white light at night and keep it constantly on, meaning that its IR is never used. This mode is ideal if you are not worried about the camera being discreet and prefer a colour picture 24/7.
.

How do I find my Hikvision device and edit its network settings?

You probably want to be able to view your camera feeds remotely wherever you are; either in a web browser, the iVMS-4200 software, or the Hik-Connect mobile app. All IP CCTV devices communicate over your LAN (local network) and have a unique location on the network. So, you will need to be able to locate where the device you want to view is and make sure it has the right settings for it to work on your LAN. You will then be able to access the device from a PC or mobile device, and connect it with the rest of your CCTV system.

Please follow the steps beneath to find and correctly set your Hikvision device’s network settings.
.

.

Step 1:
.

The first step is to work out if you need Hikvision’s SADP tool or not. If you only need to discover and access an NVR and some Plug and Play cameras connected directly to its PoE ports, then you don’t need to use it.​

​

​

If you aren’t using the SADP tool:​

​

Or, on the NVR’s local GUI (Graphical User Interface – when operating the recorder from a connected monitor and mouse), go to:​

​

System → Network → TCP/IP​

​

Here, you can view and change the NVR’s network settings to match your LAN which is explained in step 2 – you can then ignore the rest of the steps.​

​

​

If you are using SADP:​

​

If your cameras are connected to your LAN, rather than to an NVR’s PoE ports, you will need to install the SADP tool. This scans for all Hikvision devices on your LAN by their MAC addresses. Now, follow steps 2-5 below.​

Step 2:

​

You now need to identify some of your LAN’s settings, which you need to set to match on your devices.​

​

From a Window’s PC, you will need to use the Command Prompt tool to find these.​

​

If you’re using a Mac, then you can find these by launching System Preferences, and then going to:​

​

Network → Advanced (make sure your Wi-Fi/Ethernet connection is selected on the LHS) → TCP/IP​

​

​

Make a note of the following numbers, as you will need to use them when changing your device’s network settings:​

​

IPv4 Address – This is the IP address of the computer that you are using. This address is therefore already occupied, so you will not be able to assign any other devices to this specific address. The digits after the final decimal point indicate where the device is located within the range of your local network, which spans 1-254. You’ll need to change the number after the third period (or full stop/dot) to something that is between “1” and “254” and not already occupied by another device on the LAN.​

​

NB – Please see these guides for instructions on checking if a proposed IP address is occupied:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

Subnet Mask – This shouldn’t need to be changed on the NVR, it will usually be “255.255.255.0”.​

​

Default Gateway – This is the IP address that’s been assigned to your router. Any device being added to your system needs to be within the range of your gateway in order to be discoverable.​

.

Step 3:

​

Now, launch the SADP tool again. It should show a list of all the Hikvision devices on your local network and their default network settings. Provided the device is being powered and has a connection to your LAN, then it will show up here. You can also alter the device’s network settings here, and check things like the model number, serial number, the firmware version installed on it.​

​

NB – Remember that any camera that is directly connected to your NVR’s PoE ports will not show up in SADP. This is because the NVR hides any cameras directly connected to it from SADP on its own “subnet”, which is separate from your local network. Don’t worry though, as you won’t need to change the settings for these cameras. ​

.

Step 4:

​

Tick the box beside your device to view and edit the network settings.​

​

If the device hasn’t yet been connected to the network then it will show as “Inactive”. You will be asked to set a password for it when you click the tick-box for it. For more instructions on activating your device, please see Part 6.​

​

​

.

.

​

Once activated, ticking the box beside your device will change the network settings in the “Modify Network Parameters” window, so that they match your LAN. You need to make sure that you enter the password for that device before clicking “Modify” for these changes to be saved.​

​

.

Step 5:
.

Check that these changes have been reflected in the SADP device table – you may need to wait a few minutes before refreshing. If they have, then you should be to carry on with getting this device connected to the rest of your system.​

​

NB – If you aren’t the camera’s first owner then you will need to perform a hard reset on it. This will reset the device to its inactive factory state so that you can set new password by activating the camera in SADP. Once this has been done, SADP will allow you to modify each network setting edit the network settings to match your LAN so that you can use the device standalone or add it to your NVR remotely.

How do I set up events and email or push notifications on my Hikvision camera?

Video Analytics, or “VCA events”, are some of the most useful features available on a Hikvision camera. Using these will mean that your footage is analysed in real-time for any activity or abnormalities with your system that you would like to receive an alert for. The different events that are available currently (which ones are available varies which each model of camera) include:

This guide will cover the setup of three of the most popular event options:

Motion Detection – This is one of the first AI options that was introduced and will analyse your footage for any moving object in a specified part of your scene and can alert you as soon as it is detected. As it detects motion in its most basic sense, it uses less of a camera or NVR’s processing power than the other event options, meaning it is always available regardless of your video compression settings.

If you are not using a device with AcuSense then this option will give you the most false-positive alerts, as it offers the fewest ways for filtering out moving objects that you are not interested in, such as object size and the direction or duration of the motion.

Intrusion Detection – This is similar to motion detection in that it will alert you when a moving object is detected within a predefined “intrusion zone”. However, this is better if you want more control over when you are alerted as it will only notify you when a moving object enters the zone, rather than whenever movement occurs within it. This event type also allows you to specify the size of trigger objects, as well as how much of an object enters the zone and for how long before you are alerted.

Line Crossing Detection – This option is particularly useful for various entrances, boundaries, and roads, etc., as it allows you to draw a line in your scene so that you are notified when an object moves across that line. Importantly, you can specify the direction(s) of movement across the line on which you are notified. Like intrusion detection, you also have more control over the size of the trigger object and how much of it must cross the line.
.

Note – Before starting, you will need to check that your Default Gateway and DNS Server are correctly set up in your device’s network parameters, as these need to be right in order for you to be sent email notifications. To check these, please see part 2.​

​

.

Section 1: Setting up motion detection​

​

Step 1:​

Connect to your device’s web browser interface by browsing for its IP address and log into it. If it is recording to an NVR, then connect to this, as this is where you should set your events from.​

.

Step 2:​

Once you’re in, navigate to:​

​

Configuration → Event → Basic Event → Motion​

​

If you’re using an NVR, select your camera from the “Camera” dropdown.​

​

​

Note – To set one of the other VCA event options, you’ll need to go to “Smart Event” rather than “Basic Event”, where you will be shown a list of tabs with all the other available events on your camera. ​

​

Step 3:​

Tick the “Enable Motion Detection” box.​

​

​

Step 4:​

Decide if you want to enable “Dynamic Analysis for Motion”. When this is turned on, green squares will show on anything that triggers motion detection in the camera’s feed, which can help with identifying exactly what has triggered the event.​

​

​

Note – Cameras usually determine what is ‘motion’ in your scene by detecting pixel changes in the image, as a large amount of pixel change usually indicates movement. However, if there is lots of visible noise in your image due to gain control in low light, you will probably see a high number of false alerts on the camera. Using one of the more advanced event types, or the camera’s built-in LEDs to illuminate the scene, will help here. ​

​

Step 5:​

Once you’re happy with the view of your scene, click on the hexagon or “Draw Area” button in “Area Settings”, which will allow you to use your mouse to draw the area within which you would like motion detection to be active.​

​

On Easy IP 3.0 and earlier cameras, These areas will be indicated by a red grid or polygon that appears when you click on part of the scene.​

​

The newer cameras will get you to draw one solid shape for each of your detection areas by left-clicking to set each point of that shape. When you have set all the points that you need, right-clicking will complete the shape and allow you to draw any others that you need.​

​

To clear your zones, just click the cross or “Clear All” button.​

​

Note – If you are not using an AcuSense camera or NVR, then you should make sure that the edges of your detection zones are not on top of anywhere that is likely to see a lot of movement, shadows, or reflections (e.g. roads, foliage, windows or the sky), to mitigate the number of false triggers. ​

​

​

​

Step 6:​

If you’re using an EasyIP 4.0 camera, draw any more detection zones that you need by repeating step 5 above.​

​

​

​

Step 7:​

Adjust the “Sensitivity” bar if you need, which determines how sensitive the detection is to pixel changes. The higher the sensitivity, the more easily motion detection is triggered, meaning you will receive more alerts as a result.​

​

A good starting point for the sensitivity is 60, but you will likely need to tweak this yourself over time to identify the optimum setting for your scene.​

​

If there is lots of activity in your scene, then avoid setting the sensitivity too high so that you don’t receive lots of false-positive triggers.​

​

Note – In the case of Line Crossing and Intrusion Detection, the sensitivity setting refers to the amount of an object that is needed to cross the line, or enter the box that you’ve drawn, before the event is triggered. ​

​

​

.

Step 8:​

If you’re using AcuSense features, then use the “Detection Target” boxes to specify what you want to trigger the event. You can select both “Human” and “Vehicle” here if you are interested in both.​

​

.

Step 9:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

​

.

Section 2: Setting up line crossing detection​

Step 1:​

In a web browser, go to:​

​

Configuration → Event → Smart Event → Line Crossing Detection​

​

If you’re using an NVR, select your camera from the dropdown at the top of the page.​

​

​

​

Step 2:​

Tick the “Enable Line Crossing Detection” box.​

​

​

​

Step 3:​

Click on the line button or “Draw Area” to draw your line on the video feed – you can move, rotate or resize however you like. ​

​

.

Step 4:​

Set your maximum and minimum target sizes by clicking the size filter buttons, and drawing these on the camera preview.​

​

Anything that crosses your line and is smaller than your minimum box, or larger than the maximum box, at the point of the line, will not trigger the event.​

​

You should use objects or vehicles in the scene to guide you here. For example, I have set the minimum target size to be slightly smaller than any car that’s near where I’ll draw my line, and the maximum to be slightly larger than a large HGV.​

.

Note – It doesn’t matter where boxes are on the feed. Also, these boxes will only be visible on this event page, and will not show up on your footage in the live view or playback pages. ​

​

.

Step 5:​

If you’re using an AcuSense camera or NVR, then specify the “target(s)” that you would like to trigger the event by ticking the box. There is no issue with ticking both “Human” and “Vehicle” here. ​

​

​

​

Step 6:​

Specify your “Direction”, which refers to the direction from which an object much cross your line to trigger the event. The different options available are explained beneath:​

​

A<->B – Any object crossing from either direction will trigger​

​

A->B – Any object crossing from side “A” to side “B” will trigger (In this case, from left to right)​

​

A<-B – Any object crossing from “B” to “A” will trigger (In this case, from right to left)​

​

​

​

Step 7:​

Adjust the sensitivity bar to suit your needs. Setting this high will reduce the amount of an object that is needed to cross your line before this is triggered. This will, of course, result in more triggers. As the optimum setting here depends on how busy your scene is, we recommend starting at 60 and then adjusting the bar over time until you find the best results. ​

​

​

​

Step 8:​

Use the “Line” dropdown to select and draw any more lines, repeating steps 2-8 above.​

​

.

Step 9:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

​

​

.

Section 3: Setting up intrusion detection​

​

Step 1:​

In a web browser, go to:​

​

Configuration → Event → Smart Event → Intrusion Detection​

​

If connected to an NVR, select your camera from the dropdown at the top of the page.​

​

.

Step 2:​

Tick the “Enable Intrusion Detection” box.​

​

.

Step 3:​

Click on “Draw Area” to draw your intrusion zone (or “Detection Area”) on the video feed, which can be a 3 or 4 sided shape. Left-click on the camera preview to set each of these points. Once your zone is drawn, you can still move each of the points to change the shape to better fit your area of interest.​

​

Note – If the edges of your zone are very close to a road, foliage, or anywhere that is likely to see lots of movement, then you will likely see a number of false-positive alerts. This is because any movement on these lines can trigger the event. If you can, you should allow for a bit of a gap between these parts of the scene and your intrusion zone. ​

​

​

​

Step 4:​

Set your maximum and minimum target sizes by clicking the “Size Filter” buttons, and drawing these on the live camera feed above.​

​

Anything that enters your configured intrusion detection zone and is smaller than your “Min” box, or larger than the “Max” box, will not trigger the event.​

​

You should use objects or vehicles in the scene to guide you here. For example, I have set the minimum target size to be smaller than the smallest person I’d expect to see in that part of the scene, and the maximum to comfortably cover a very tall person.​

​

Note – It doesn’t matter where boxes are on the feed. Also, these boxes will only be visible on this event page, and will not show up on your footage in the live view or playback pages. ​

.

.

Step 5:​

If you’re using an AcuSense camera or NVR, then specify the “target(s)” that you would like to trigger the event by ticking the relevant box. There is no issue with ticking both “Human” and “Vehicle” here.​

​

.

Step 6:​

Now, adjust the “Threshold” bar as you need. This can be set between 1 and 10 seconds and refers to how long an object needs to be within your intrusion zone before triggering the event. For example, setting this to “0” will mean that the event is triggered as soon as a valid target enters your zone.​

​

.

Step 7:​

Adjust the sensitivity bar to suit your needs. Setting this high will reduce the amount of an object that is needed to enter your zone before the event is triggered. This will, of course, result in more triggers. As the optimum setting here depends on how busy your scene is, we recommend setting this to 60 and then adjusting the bar over time until you find the best results.​

​

​

​

Step 8:​

Use the “Region” dropdown to select and draw any more intrusion zones, repeating steps 2-6 above.​

​

​

Step 9:​

Click on the “Arming Schedule” tab and set this by filling in the hours you want the event to be enabled for in blue.​

​

Note – Please see section [1] step 9 above for a more detailed explanation on how to set your arming schedule. ​

​

​

Step 10:​

Click “Save” at this point so that you don’t lose these settings. ​

​

You’ll now need to go to the “Arming Schedule” and “Linkage Method” pages to set when you would like the event to be active, and what you would like to happen on triggers.​

​

Please refer to sections 4 and 5 below for instructions on how to set these things.​

.

.

Section 4: Setting the Arming Schedule for your events​

Now that you have set your “Area Settings”, click on the “Arming Schedule” tab to set when the event will be active.

This will bring up a timeline with the week broken up into days and hours – depending on the device that you are using, it might look different to the grid below. If a period is filled in blue then the event will be active (or “armed”) for that hour; If the period is white, the event will be off.

Use your mouse to draw up the weekly Arming Schedule that suits. You can also use the popup box that appears when you click on any blue period to finely adjust the start arming times:
.

Clicking on the “Erase” button and then a blue period will allow you to clear the arming:
.

When you’re happy with this schedule, click “Save”.

.

.

Section 5: Setting up email & push notifications for your events​

.

Click on the Linkage Method tab on the event’s page (shown above), which is where you will set up your email notifications, as well as other alert types.​

​

The different options are explained below:​

​

Audible Warning: This will cause the NVR / browser to bleep when on event triggers.​

Send Email: This will set the NVR to email you on event triggers, with a screenshot of the camera’s view at the time.​

Notify Surveillance Centre: This refers to Hik-Connect and needs to be activated in order to receive push notifications in Hik-Connect.​

Full Screen Monitoring: This will get the NVR to automatically throw up a camera’s live feed in full screen during a trigger for an event set on that camera.​

​

​

.

.

To enable Hik-Connect push notifications:​

.

To set up push notifications, you need to make sure that Notify Surveillance Centre is ticked as a “Linkage Method”.​

​

You also need to make sure that push notifications are enabled for Hik-Connect in your phone’s settings. To enable them via the app, go to:​

​

More → Settings → Enable Push Notification​

​

​

……..

.

New GUI – Start Up Wizard (Device Initialization)

DAHUA XVR 4.0 Setup Description

This article will go over the Initialization process of the units with the New GUI.

Prerequisites

Video Instructions

Step by Step Instructions

1. When you first turn on the recorder you will be greeted with the region settings. Click on the drop down menu and select “United States” and click Next.

2. Select the proper time zone setting for your region.

3. You will now be prompted to input a password for the admin account.

4. For easier login you can create a pattern, you will need to enter it twice to confirm.

5. Enter your email in order to reset the admin password in case the password was forgotten, you may also setup security questions.

Note: This is the only method to reset the password for XVRs and NVRs. If you skip this step and forget your device’s password, you will need to replace the unit

6. The Auto-check for firmware is not yet implemented in the U.S. so you can just click on next.

7. Make sure the video standard format is set to NTSC and click on “Next”.

8. Here you can go in depth with the time settings. You may want to set up the DST (Daylight savings) so that it takes affect when the time comes.

9. The recorder will be set as a static default IP address you see on the screen. Input an open local IP address and gateway from you network. If you don’t know this information you can select DHCP (highlighted in the red box) in order to automatically receive an IP address from the router.

10. If you have the recorder properly connected to the router the P2P status will indicate “Online” and you can now remote in to the unit with our mobile app/PC app.

11. You can select the Encode settings for each camera by selecting the drop down menu on “Channel”.

12. Select the resolution and image quality for snapshots.

13. Select what you want to to when the hard drive fills up.

14. Here is you recording schedule, the green will indicate 24/7 recording and Yellow will be Motion recording.

15. Here is you Snapshot schedule, same color legend as recording,

16. Once all that is setup you will be greeted with the final Prompt! You are now finished Initializing you new recorder

New GUI- Add a Dahua Device

Description

This article will show you three different methods to add a dahua device to our New GUI recorders. We will be adding a dahua camera with all three methods.

Prerequisites

Video Instructions

Step by Step Instructions

Method 1:

This first method is extremely simple if all the cameras are still set to default credentials and settings. We will do a device search on the network and add them with a click of a button

Method Two:

The second method is used if there’s an existing camera and it’s password was changed. You will use device search to locate the camera and then go to manual add to change the password it’s being added with

Method Three:

This last method is used when Device Search fails and cannot locate the camera on the network. You will need to type in the camera’s information manually.

New GUI – Account Setup

Description

This article will go over how to add a user on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Log into the web interface of the device

.

2. Click the Menu icon in the top left of the page

.

3. Select Account

.

4. Click Add User

5. The Add User menu will appear. Use this window to ill out full user details

6. In the Authority menu you can define the individual rights of the User using the System, Playback, and Monitor tabs as well as which channels the user can access

Select which features you wish the user to have then click Save

7. A message will confirm when the user is successfully added

New GUI – Schedule Record Setup

Description

Dahua NVRs and DVRs offer a variety of recording options. You can configure recording schedules based on the following methods:

These schedules can be set individually for each camera or copied to all cameras.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Management”.

2. Select the “Storage” option from the drop-down menu.

3. From the left hand side, select “Schedule”.

4. Select the channel drop-down menu to choose the channel that you want to adjust the recording schedule for.

5. Select “Setting” next to any day of the week.

6. You will have options to set a schedule for General Recording, MD (Motion Detection), Alarm, MD & Alarm, Intel, and POS (Point of Sale). For this tutorial we are using General Recording.

7. Here you can see that you are able to set multiple periods. For this tutorial we will only be setting one period. Check the “General” box, then select the day or days you want to scheduled recordings for, and then select “Save”.

8. Depending on the days selected from the previous step, you will see green colored bars which represents general recording.

9. You can select “Copy” to mirror the same schedule to another channel/camera. Select “Save” in the Copy menu.

10. Select “Save” at the bottom to save all settings. If your changes were successfully saved, a pop-up will appear at the top notifying you as such.

New GUI – Motion Detection Recording Setup

Description

This article will go over Motion Detection Recording setup in detail on the recorder’s new GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. On the main menu select Alarm

2. Select Video Detection on the left.
Then select the Motion Detection tab at the top.
Choose the channel from the drop-down next to Channel.
Check the box next to Enable.
Check the box next to Record Channel.
Click on Setting next to Region

3. Highlight the areas in red where you want to track motion.
Then click OK at the bottom

4. Select More at the bottom
Check the boxes next to any of the other options you want to activate when motion is detected.
Click on OK

5. Click on Apply at the bottom.
You will see “Operation Succeeded” at the top when your changes have been saved

6. Click on the Setting drop-down at the top and select Storage

7. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel from the drop-down next to Channel.
Click on the Setting button next to any day of the week.

8. Check the All box to enable all days of the week.
Check the Motion box for “Period 1”.
Click OK at the bottom.

9. Click on Apply at the bottom to save the settings

10. Select Record Mode on the left.
Then make sure Auto is enabled for the appropriate channel(s).
Click on Apply at the bottom.

11. Click on the Main Menu icon at the top right.
Then select Search

12. Check box next to the channel on the right.
You should see yellow lines/bars for motion recording

Alarm Record Setup

Description

This article is to show you how to setup alarm recording thru new Web GUI.

Note: please refer to product spec sheet for alarm input/output availability. Not all Dahua Recorder support alarm input/output.

Prerequisites

Video Instructions

Step by Step Instructions

Setup Alarm Input

From main menu, click on Alarm. Click on Alarm input. We are using XVR 72 series for this example. The Alarm Input page will launch as shown below:

Select the Alarm input number that you like to use. This number is correspond to the alarm port on the back of recorder.

1. Click Enable to enable the alarm input.

2. Enter Alarm Name. By default is set to AlarmIn#

3. Period is to schedule your Alarm when you want to be enable.

4. With the alarm input, you can trigger recorder’s alarm output.

5. This to select which channel you want recorder to start recording when alarm is triggered.

6. You can call basic PTZ action Preset, Tour, or Pattern when alarm is triggered.

.

Setup Alarm Recording Schedule

1. From the main menu, click on Management > Storage > Schedule.

2. Select the channel you like to setup.

3. To enable Alarm recording, Click on Setting next to the timeline bar.

4. Set your duration (By default is 24 hour, 00-24). Then select Alarm.

You can select all days to copy the schedule to all week. Click Save.

5. Click Save.

New GUI/Instructions/IVS Record

Description

This article will cover how to configure IVS Recording on a Dahua recorder with the New GUI

Prerequisites

Video Instructions

Step By Step Instructions

1. From the Main Menu select AI

2. Select Parameters on the left.
Then select Smart Plan below it.
Choose the channel of the camera you are configuring from the Channel drop-down.
Select the IVS “Lightbulb” icon so that it highlights blue.
Then click Apply at the bottom

3. Select IVS on the left.
Choose the channel of the camera from the Channel drop-down.
Then click the + button.
Double-click on the rule type under the Type column to choose the type of IVS rule you want to use.
Adjust all the settings in the Parameters section.
Make sure that the box is checked next to Record Channel and the channel that camera is on is highlighted next to it

4. Draw the rule in the live view on the left by left clicking on it.
Continue to left click to add more segments.
When you are done, right click to finish drawing the rule.
Then click Apply at the bottom

5. Select Setting at the top left.
Then select Storage from the drop-down

6. Select Schedule on the left.
Then select the Record tab at the top.
Choose the channel of the camera from the Channel drop-down.
Then click on Setting to the right of any day of the week

7. Check the box next to All to select all days of the week.
Check the box for Intelligent to the right of Period 1.
(Feel free to adjust the days of the week and the time period for when you want to record IVS events).
Then click on OK

8. You will see blue bars on the schedule representing when IVS events will be recorded, when they are triggered.
Click Apply at the bottom

9. Click on the Menu icon at the top right to go back to the Main Menu.
Then click on Search

10. Check the box next to the camera channel on the right.
Once IVS events have occured they will appear as blue bars on the timeline at the bottom.
Click on the timeline on one of the blue bars to start playing that IVS event

New GUI – Audio Record Setup

Description

This article will go over setup for audio recording on our New GUI devices

Prerequisites

OR

Note: Please reference the specification sheet for the device to confirm which audio features it supports, this can vary between models of recorder

Video Instructions

Step by Step Instructions

Enable audio source

1. 1. Login using a web browser.

2. Click on Setting > Camera.

|

3. Click on Encode. And then select the camera channel that support audio.

|

4. Click on More.

5. Click on the checkmark to enable Audio.

6. Select the Audio source for your HD-CVI camera. If your HD-CVI camera has built-in Microphone, select HDCVI as the audio source. Local option is if you are connecting external microphone to the recorder.

7. Click OK, and then click OK again on the bottom right hand corner.

Setup audio recording

1. Login using a web browser.

2. Main menu 1st screen.

3. Main menu 2nd screen.

4. Click on the Audio Option.

5. Audio File Manager Option.

New GUI – Playback

Description

This article will cover how to play back recorded video on an NVR or DVR with the New GUI

Prerequisites

Video Instructions

Step by Step Instructions

1. From the Main Menu select “Video”

2. The Playback menu should open up and look like this:

3. On the right hand side, there will be a calendar. Select the day that you wish to play back video.
Below the calendar is a list of all the cameras/channels. Check the box next to all the cammeras/channels you would like to play back video from.

4. The video footage willl appear on the timeline at the bottom of the screen. It will be color coded to match the types of video that were recorded.
(See the Legend at the bottom of the screen.)

5. Check or uncheck each type of recording that you want to view. Check the Sync box if you would like to sync playback up on all channels you are viewing.

6. Double click on the graph at the bottom to begin playing back video.

=How to back up video files on new UI

Description

This article is to show you how to back up the video file from new system UI.

Prerequisites

Video Instructions

Step by Step Instructions

1. From the main menu, go to the second menu page, and click on Backup.

2. Backup page will launch as shown below:

3. You must plug in an external drive to save your downloaded file. Select the path where you want to save the file at. From this pop-up screen, you have an option to create new folder. After you select, click OK.

4. Select the Record Channel you like to search. You can only search 1 channel at a time.

5. Select the Recording Type you like to search.

6. Set the start and end time for searching. Then click Search. All recorded files that meets your search criteria will shown on the list.

7. Select the files, and click Backup.

8. Downloading process start.

9. Once finished, the folder information will pop up, then click OK.

New GUI – P2P Setup

Description

This article will go over initializing P2P on our New GUI devices

Prerequisites

Video Instructions

Step by Step Instructions

1. Under “Management” go to Network>TCP/IP

2. You can either set the device on a static ip or turn DHCP on to automatically grab an IP from the network. Save any changes

3. Locate P2P tab on the lower left and enable P2P

4. After saving it you should see the the status change to “Online”, You can now use this device for remote viewing on our software

Remote Access/Remote Access Setup Port Forwarding

Create port forwarding rule in the router

Description

Port forwarding is a function of network routers that allows a user to configure specific communication ports to be routed to devices on an IP (Internet Protocol) network, such as a computer, DVR, or IP camera.In this case for CCTV equipment, it allows the user to view and control CCTV equipment remotely. Follow the step by step instructions and the instructions your manufacturers hardware to setup port forwarding, or try PortForward.com to search for your routers settings.

Prerequisites

Video Instructions

Step by Step Instructions

1. Connect NVR to network with a CAT5 cable.

2. Download and install ConfigTool from DahuaSecurity.com, under Support->Download Center->Software

3. Run the ConfigTool.

4. The ConfigTool should display your IP Camera. Click the, “” icon to open Internet Explorer and access your NVR.

5. Configure Internet Explorer security settings to allow the plugs to work. Link to Internet Explorer Setup

6. Login with the default credentials: User Name: admin Passsword: admin

7. Under, Main Menu -> Setup -> TCP/IP Change the IP Camera to, “Static” if the camera is currently set to, “DHCP”

8. Open another tab and enter the, “Gateway” address listed under your NVR’s Network settings. Example: 192.168.1.1, 192.168.0.1, 10.0.10.1

9. Login to your gateway and locate the, “Port Forwarding” section.

10. Create port forwarding rules for each port you wish to forward for the NVR. (Usually you will only need to forward the HTTP and the TCP port.) Default Ports: TCP: 37777 UDP: 37778 HTTP: 80 RTSP: 554 HTTPS: 443

11. The end result should look like the below image. We used a Cisco router for this example.

12. Hit, “Save” in the gateway interface, and open another tab.

13. Go to, “www.canyouseeme.org” and check that the ports you opened on the gateway.

How to Access System Using P2P via Mobile Application

Description

View your recorder and cameras on the go. With Dahua’s mobile application IDMSS(IOS)/GDMSS(Android) allows you to add Dahua recorders and cameras to the mobile app using P2P.

Prerequisites

Video Instructions IDMSS/GDMSS version 4.50.000

Step by Step Instructions iDMSS/gDMSS version 4.50.000

1. Open iDMSS/gDMSS on the phone, and select the home icon located on the top left corner.

2. Select the “Device” button/icon on the bottom to add the recorder/camera.

3. Select the “+” sign then select “Scan” to add the device.

4. Select the “Wired Camera”.

5. Input the device for easy identification. It’s required to input the password for the added device then select the save icon located on the top right corner.

Step by Step Instructions IDMSS/GDMSS version 4.20.000

1. Select the Menu Icon

2. Select “Device Manager”

3. Select the Add Icon

4. Select “Camera”

5. Select “Wired Device”

6. Select “P2P”

7. Input Info and select “Start Live Preview”

Video Instructions IDMSS/GDMSS version 3.50.000

Step by Step Instructions IDMSS/GDMSS version 3.50.000

1. From the home screen of the mobile application select “Camera”.

2. Select the menu button.

3. Select Device Manager.

4. Select add button to add device.

5. Select Wired Device.

6. Select P2P.

7. Name your device -> tap the QR code to bring up QR code scanner.

8. Input the username -> password -> and select live preview. By selecting “Start live preview” device will be automatically saved into the application.

IDMSS/GDMSS Version 3.40.003

Video Instructions Version 3.40.003

Step by Step Instructions Version 3.40.003

1. Click, “Camera”

2. Select the Menu Icon

3. Select “Device Manager”

4. Select the Add Icon

5. Select “P2P”

6. Choose a name for the device → Scan in QR code for SN number which you can access from the physical recorder under the main menu → Setting → Network → P2P. You may input SN number manually which can also be found under the recorder. → Enter Username and Password. For best results , leave Live Preview and Playback on the Extra Stream.

7. Select the Disk Icon to save → Select Live Preview, At which time the app will connect to all cameras.

Setup Remote Access via P2P using SmartPSS

Description

This allows you to view cameras on SmartPSS using P2P.

Prerequisites

Video Instructions

Step by Step Instructions

1. Locate the serial number of your NVR or DVR. The serial number can be found at the following locations:

2. Launch SmartPSS and select Device.

3. Click Add, change method to P2P.

4. Enter credentials, save and then add.

.

How to Download and Prepare Firmware

Description

This guide will show how to download and prepare the firmware file for a Dahua device.

Firmware files for Dahua devices can be found at Firmware by Device or the specific product page for the device

Firmware is typical provided in a ZIP file, a compressed file format

This file will contain the actual firmware file, which needs to be extracted from the ZIP file in preparation for the upgrade

Prerequisites

• Computer with internet access (to download firmware file)

• Dahua device

Video Instructions

Step by Step Instructions

Confirm the Model and current firmware of Dahua device

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Info

3. Click Version

The Device Type will be displayed

The current System Version will be displayed

Download the firmware file for device from DahuaWiki

4. In a browser go to DahuaWiki.com

Under Specifications, Firmware, & Manuals

Click the device type (in this example Recorder)

5. Enter the device model into the field

6. The results will be filtered

7. Click the firmware icon to download the firmware file

8. The file will download

Extract the firmware file to local computer

9. Right click the Start Menu / Windows icon in the bottom left of the screen

Select File Explorer

10. Select Desktop

11. Click Home

Then click New folder to create a new folder to extract the contents of the firmware zip file

12. Find the created folder in the list, double click to open

13. Under the Downloads window of the browser, click ‘Show in folder’

A new File Explorer window should open containing the directory the firmware zip was downloaded to

Locate the file in the list

14. Right click

Select Cut

15. Select the window with the new directory

Right click in the window

Select Paste

The folder will appear in the directory

16. Right click the file

17. The contents of the zip file will appear in a new window

18. Click to select all files in the folder

Drag and drop the files to the created folder

The files will appear in the directory

The firmware file will appear in the directory ready to use

How to Reset Device to Factory Default

Latest Dahua firmwares 2024

Step by Step Instructions

1. From Live View

Right click select Main Menu

2. Under Setting

Click System

3. Click Default

4. Click Factory Reset

5. A prompt will appear to confirm the factory default

Click Yes

6. The unit will default and reboot

7. When the device has booted back up it will be factory reset and is now ready for device initialization

SystemUI New

Step by Step Instructions

1. From Live View

Right click, select Main Menu

2. Click Operation

3. Click System Maintain

4. Click Default

5. Click Factory Default

6. A prompt will appear to confirm the factory default

Click OK

7. The NVR will default and reboot itself

8. The unit will boot back up

9. The device has been factory reset and is now ready for device initialization

WebUI Old

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Setup

3. Click System

4. Click Default

5. Click Factory Reset

6. A prompt will appear to confirm the Factory Reset

The unit will reboot and is now ready for device initialization

WebUI New

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Setup

3. Click System

4. Click Default

5. Click Factory Reset

6. A prompt will appear to confirm the factory default

Click Yes

The unit will reboot and is now ready for device initialization

Firmware Update via USB Drive

Description

This page will show you how to update the firmware of your Dahua device via a USB drive at the recorder

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device

• USB drive with the firmware file for the device – Firmware by Device

SystemUI Old

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

1. Download Firmware and copy to USB such as a flash drive ➞ Insert USB into recorders USB port.

2. It will prompt for option to upgrade, Click System upgrade ➞ Click Start.

3. Browse for firmware ➞ Open firmware folder is in ➞ Select Bin File ➞ Click Start. Device will reboot once finished.

SystemUI New

Prerequisites

• USB Drive 1GB or more

• The proper firmware file for the device

• Physical access to the recording device

• A computer to load the firmware files onto the USB

Video Instructions

Step by Step Instructions

USB drive with Firmware file should be plugged into USB slot on recorder

1. From the Main Menu, click Operation

2. Click System Maintain > Upgrade

3. Click the System Upgrade in the middle of the page.

4. Select the Firmware file from the list

Click OK

5. The firmware update will begin.

Make sure to not unplug the power during this process.

6. The NVR will reboot as the final step of the process

Firmware Update via WebUI

Description

This page will show you how to update the firmware of your Dahua device via the WebUI

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device with network connection

• Local Windows computer

• Firmware file for device downloaded to computer – Firmware by Device

Instructions

WebUI Old

Prerequisites

• Computer

• Internet

• Compatible Browser (Internet Explorer)

• NVR/HCVR/IPC

Video Instructions

Step by Step Instructions

Step 1: From IE(Internet Explorer) type in the devices IP address on the IE address bar → login with credentials.

Step2: Setup → System → Upgrade

Step 3: Click on “Browse” → Select correct firmware

• Click on “Upgrade”

• Device will reboot after upgrade is finished.

USB firmware Upgrade via web.

If firmware is on USB Device → Click on browse → Navigate to USB location → Select firmware → Open → Upgrade.

WebUI New

Prerequisites

• Dahua device with network connection

• Local windows computer

• Firmware file for device downloaded to computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Operation

3. Click System Maintain

4. Click Upgrade

5. Click Browser

6. Locate the firmware file

Click Open

7. Click Upgrade to begin the update process

8. A message will appear to confirm the upgrade process

9. When the upgrade is complete the device will reboot

Firmware Update via SmartPSS

Description

This page will show you how to update the firmware of your Dahua device via SmartPSS

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• SmartPSS installed

• Device added to SmartPSS

• Firmware file downloaded to computer – Firmware by Device

Instructions

SmartPSS 2.002

Prerequisites

• SmartPSS installed

• Dahua device added to SmartPSS

• Firmware file for device downloaded to computer – Firmware by Device

Video Instructions

Step by Step Instructions

1. From the Main Page of SmartPSS

Click Device CFG

2. Click to select the device from the device tree on the left side of the screen

3. Click Upgrade

4. Click the folder icon

5. Locate the firmware file

Click Open

6. Click Firmware Upgrade to begin the firmware update process

7. A prompt will appear to confirm the upgrade process

8. A prompt will appear to confirm a successful upgrade

Firmware Upgrade via ConfigTool

Description

This page will show you how to upgrade the firmware of your Dahua device via ConfigTool

Note: All devices should be “Factory Reset” once the firmware update is complete.

Prerequisites

• Dahua device(s) with network connection(s)

• ConfigTool installed on a local computer

• Firmware file for device(s) downloaded to computer – Firmware by Device

Step by Step Instructions

Single Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the device you are looking for in Start IP and End IP.
Enter the login information for that device in Username and Password.
Then click OK at the bottom

3. Click on Device Upgrade on the left.
Find the device you want to upgrade in the list and click on the Folder icon next to it under the Upgrade File Path column

4. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

5. Verify the file path is listed next to the device in the list.
Then click on the Upgrade icon to the right of the device in the Operate column

6. Click on OK

7. The progress bar will fill up as the device is upgraded

8. Once the device has been successfully upgraded you will see a Green Check Mark next to it in the list

Batch Device Upgrade

1. Open ConfigTool and click on Search Setting at the top

2. Check the boxes for both Current Segment Search and Other Segment Search.
Enter the IP range for the devices you are looking for in Start IP and End IP.
Enter the login information for those devices in Username and Password.
Then click OK at the bottom

3. Click on Device Upgrade on the left.
Find the devices you want to upgrade in the list and check the boxes next to them. (Make sure all devices you check require the same firmware.)
Then click on Batch Upgrade at the top

4. Click on OK

5. Click on Browse

6. Use the file explorer to find the firmware file on your computer and select it.
Then click on Open

7. Click OK at the bottom

8. The progress bars will fill up as the devices are upgraded

9. Once the devices have been successfully upgraded you will see Green Check Marks next to them in the list

Recorder Firmware Update via Online

Description

This page will show you how to update your Dahua Recorder online.

Note: All devices should be “Factory Reset” once the firmware update is complete.

When the NVR detects there is a newer firmware in the server, a ‘1′ icon will appear at the System icon.

The entire process takes about 5 minutes depending on network connection.

Prerequisites

• Dahua device that supports online update

• Internet connection to Dahua device

Instructions

SystemUI

Prerequisites

• Dahua device with internet connection

Video Instructions

Step by Step Instructions

1. From Live View

Right click, select Main Menu

2. Click Operation

3. Click System Maintain

4. The upgrade menu will show if a new firmware version is available

5. Click Upgrade Now to begin the update process

6. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

7. The firmware file will begin to download

8. After the download is complete the unit will automatically begin the firmware upgrade

9. The unit will reboot as the final step of the upgrade

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

From Live View, right click Select Main Menu

11. Click Operation

12. Click System Maintain

13. Click Default

14. Click Factory Default

15. A prompt will appear to confirm the factory default

Click OK

16. The unit will reboot

17. When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

WebUI

Prerequisites

• Dahua device with internet connection

• Local Windows computer

Video Instructions

Step by Step Instructions

1. Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

2. Click Operation

3. Click System Maintain

4. Click Upgrade

5. The upgrade menu will show if a new firmware version is available

6. Click Upgrade Now

7. A prompt will appear to confirm that Surveillance will be paused during the upgrade process

Click OK

8. The firmware file will begin to download

9. After the download is complete the unit will automatically begin the firmware upgrade

10. Once the firmware update is complete the unit will reboot. A factory default is recommended after a firmware update

Enter the IP of the device into a browser

At the Web Login

Enter the Username and Password

Click Login

12. Click Operation

13. Click System Maintain

14. Click Default

Click Factory Default

15. A prompt will appear to confirm the factory default

Click OK

The unit will factory default and reboot

When the unit boots back up it will be factory defaulted and ready for the Device Initialization process

Index of /Firmware

.

.

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

How do I access the cameras on my computer?

Go Here, login using with the credentials you used to sign up with. You will see your devices at the top, click ACCESS and it will launch a new tab for that device. This info can also be found by going to our website and downloading it Here 

How do I network the unit so it can be viewed remotely?

First you want to make sure you plug the unit into your router. Now on the unit login, then right click on the mouse and go to Menu> System> Network. You can set the IP Address under “TCP/IP”. Once you’ve entered your IT information go to “P2P” across the top. Make sure it is enabled. Below you will see the server address Here. You will go there and create an account then link the unit with your account. See Link below for more detailed instructions. Here

How do I connect a third party camera?

You will need a PC and the manufacturers IP tool to address the camera(s) IP address within the same scheme as the internal NIC of the NVR (172.16.0.x). Now go to the camera management within the NVR, switch the port that the camera(s) are plugged into from PNP to IP address, protocol will be ONVIF, port will be 80 (HTTP port of the camera) and type in the username and password of the camera and it should connect. Some manufacturers require ONVIF to be enabled within the camera before adding to different unit. Please check their website for information on how to enable ONVIF.

Why can’t I use Chrome, Firefox, Edge or Safari to view my device(s)?

Chrome, Firefox, Edge and Safari took away a plugin that was used for ActiveX plugins. This has effected anyone that uses an ActiveX plugin for their devices not just InVid.

Why is my Vision camera not connecting to the NVR?

That may be due to the NVR having the old default password of 123456. Leave the camera plugged into the unit and go to Menu>Camera then click on the “cog” (gear looking icon) next to the port of the camera you are trying to connect. Type in the password “1234567u” for the camera and the camera should then connect.

Why did my device suddenly go offline?

If you are connected to your ISP’s router (Internet Service Provider) occasionally it is possible your ISP is doing a update which can occasionally change your network environment and require a reboot of your router/recorder (Router first then recorder). It is highly recommended that with this device to install your own router to run the recorder to avoid this from happening, however if using your ISP’s router the above stated solution is the fix for it.

How do I Share a device added to my star4live account?

Have the new user create an account Here. Log into the account with your device, click on SHARE, enter in the customers user name or email, choose a “valid to date”, when this date hits the device will no longer be shared, and hit ok. The device will now be found under the Shared Record. This info can also be found by going to our website and downloading it Here

Trying to view devices on IE but can’t download the plugins?

Please ensure you are in fact using Internet Explorer and not Edge. The two have similar icons, Edge is a darker blue lower case “e” whereas Internet Explorer is a lighter blue lower case “e” with a yellow ring going over the top left of the “e”. Also note that on Windows 10 Edge is the default browser, Internet Explorer isn’t on the task bar or the desktop, you can use Cortana and search “Internet Explorer” to launch.

How do I turn On/Off motion function?

Right click on the mouse, go to the menu>alarm>motion. By default motion detection should be enabled. You want to draw the area of where you want motion to be detected and then hit apply down at the bottom.

How can I see video from last week?

To playback video you want to right click on the mouse and the second to last option on the bottom is “Playback”. On your right you will select which cameras you will like to playback, below the camera list select the date in which the video was recorded. Hit the play button down at the bottom and the playback should start.

How do I add a User?

Right click on mouse go to Menu>System>User. Click Add at the bottom. Create the username and password then select permissions you want to grant that user and hit OK.

How do I format my hard drive? Vision Series

Go to Menu, click on Storage, click on Hard Disk, select your disk(s) and click Format (remember, this erases all data on that drive(s)).

Do I need to port forward this device? Vision

If you’re using the P2P which is explained above no port forwarding is required, if you are networking this device to be seen remotely via a WAN IP or DDNS, yes port forwarding is required.

Is there a manual for this device?

Yes, you can find it on our website Here

Where can I check to see if my unit is recording?

The best way is by doing a playback (refer to question above). You can also go into the Menu, select Maintain on your left and Recording across the top.

InVidTech Vision Series Setup Guide v1

How to Setup Vision Email Notification

Learn how to setup email notification on your Vision machine

Step 1: Setting up a GMAIL account.

1. Go to My Account setting page, click on the square and click my account.

2. Click Signing in to Google.

3. Click Allow all less secure apps on

Step 2 – Setting DVR/NVR Configurations

Enabling Motion Detection

Hit Apply to save then OK

What is the default password of the Vision devices?

We provide a sticker on the inside of the boxes, whether it’s a DVR Encoder, NVR or IP Camera. The default user name and password could be either “admin/123456” or “admin/1234567u”. Once the change-over is fully complete they will all be “admin/1234567u”

How to Setup Vision P2P Using the QR Code

With P2P QR connection there is no need to set any ports, worry whether or not your uPnP is enabled within your router, do any port forwarding within your router or setup a DDNS name.

Not connected? Here are some things to check

Viewing your Vision Device Online or from Mobile App

Viewing from your Web Browser (Internet Explorer):

Viewing from your InVid Vision mobile app:

Is my unit up to date with its firmware?

To find out if the unit is up to date Locally, you want to go to the Menu, select Maintain on your left then Upgrade. Now select “Upgrade by Cloud” (across the top) then hit “Check” in bottom right had corner. To find out if the unit is up to date Remotely, you want to go to Setup, then Maintenance then Maintenance again and hit “Check New Version”. If it is the latest firmware it will say “The current version is already the latest.” If it is not up to date then you will be prompted to upgrade, which will download the file from the cloud, upgrade and restart your NVR.

How do you check to see if an upgrade is available for the Vision NVR?

Is it possible to reset a password for a device?

Yes please contact our Tech Support, 631-388-5700.We will need the devices FULL serial number, you can do this at the main monitor or from the web interface.

How do I access the cameras on my phone?

Once you have downloaded the VISION app from the App Store or Google Play store, sign in with your login credentials used when creating your star4live account.Hit the camera icon in the top right hand corner and you will see a list of all devices added to your account.Choose the device youd like to access and hit “Start Live View” at the bottom of the screen. This info can also be found by going to our website and downloading it Here

Where do I download the APP?

-The app can be found at either the app store for an Apple device, or the Google Play store for an Android Device, you want to search “Paramont CMS”. This info can also be found by going to our website and downloading it Here 

What App do I use for my phone?

InVid Vision

How do I view my device(s) on my Mac?

The current work-around is to install the appropriate CMS software which will allow you to watch live and playback your device(s). You can download the CMS software(s) off our website Here. 

.

Frequently Asked Questions

Note: These guides were written for Uniview NVR users who prefer to change settings remotely using a mobile or desktop browser (Internet Explorer). Remote and local configurations share many similarities and only the locations and availability of each feature may vary. The Uniview NVR Manual can provide more information if what you are looking for is not found in this simple guide or if you prefer local access by connecting a mouse and display to your NVR.

How Do I Access My Uniview Security System?

There are two ways to interface with your Univew Security System and to access all its features and configuration options you can choose to access it locally or remotely. Local access refers to connecting your Network Video Recorder to a display and a USB mouse. The monitor and the mouse will serve as the input-output for interfacing. Remote access refers to connecting to your Network Video Recorder through a browser (Internet Explorer provides the greatest compatibility) installed on a device that is in the same network as the Security System.

Local Access and First Time Setup

The NVR interface can be accessed directly by simply connecting the NVR to a display (this can be done with an HDMI or older VGA cable) and to a mouse. Once the display and the mouse is connected and the login screen is displayed, proceed to login. Since this is the first time, we will be using the default username and password (at the time of writing default login and password are admin and 123456) found on the manual that came with the NVR. 

After logging in, Uniview’s privacy policy will be shown for you to review. Once you have reviewed and accepted, you will immediately gain access to the NVR and cameras connected to it. But, since it is the first time we are logged in and we are still using the default credentials, we will be prompted to change the login information.  You will be using the new password for all your future access with the NVR.

Once the password has been changed, a pattern lock will also be prompted (this is optional and can be skipped). After doing so, the Privacy Policy will be displayed for the user to review. The screen that follows the Privacy Policy will let us connect our mobile devices to the NVR. This will grant access to Live View, alerts, and other configurations we may want.

The device QR code will be presented here. Allowing you access to the EZCloud feature. Devices can be added to the cloud manually but it is far easier to just use a link given from the QR code. If you want to pair the NVR with the EZView app, click here to read more about it. 

The next step is to set or synchronize the time. This step will ensure that all scheduling configurations you will set and all alerts and alarm information will be accurate and will work based on your local time.

After this, you will be prompted to check the TCP/IP settings, the default settings will work for most people. If you need to specify networking (usually when DHCP is not enabled on other devices on the network), please do so here. You will still be able to alter this later.

Once the time and the password have been configured, you are now ready to enable and disable the features of the NVR.

To access the menu, you can right-click on any part of the screen and then click on Menu. It can also be accessed along with other options by moving your cursor to the bottom left of the screen. This will take you to the SETUP screen where you can enable and customize alerts, features, and other options available to you.