Our IP camera can connect directly to your network or computer, and there are three ways to do so. The three ways listed below do not require a NVR. A NVR, or Network Video Recorder, is the device that IP cameras connect to.  The NVR records video provided by the IP cameras to a hard drive, either in HD (720p, 1080p), 2K HD, or Ultra HD (4K) depending on the type of NVR and type of camera that’s being used with it.

IP cameras are network-based cameras, however they don’t require Internet access in order to be used as they are standalone devices that can be used on a local network. A simple local network can be either of the following:

1.An IP network camera connected with a network cable to your desktop computer’s network port.

2.An IP camera connected to a router that is connected to a desktop or laptop computer, but the router is not connected to the internet.

Only if you want to view your system remotely from the internet then you would have to connect the system to the Internet.

Do I need a NVR for my IP security camera system?

A NVR is not necessary in order to view your network cameras or even record video. If you are testing cameras, looking for a temporary setup or want to set up something inexpensive then using a computer with an IP camera is a good alternative to a NVR.  SmartPSS is our computer software program that allows PCs to view and record IP cameras. However, this kind of processing will demand a lot from the computer. Most likely, you wouldn’t be able to use that computer for personal use as it would be bogged down processing video from high resolution IP network cameras.  Also, computers can be unreliable and crash, potentially leaving you with no recorded video.

NVR products are standalone devices using a Linux operating system which is known to be rock-solid and crash free, and designed to be operate 24/7 and maintain system security with user account access permissions. For a complete security camera system, you will want to use a NVR along with cameras. SmartPSS software can be used as a client software to connect from a computer to a NVR to watch cameras connected to the NVR and to playback/download recorded security footage.

How to Connect IP Camera Guide 2024

Three ways to connect an IP camera to a computer

Before we begin, it is important to understand that network camera systems require the ability to transport video and power to work correctly. Power Over Ethernet (PoE) is a technology that transmits video/data signal and power over one Ethernet cable. In situations where PoE isn’t available, a 12V DC power adapter will be necessary to supply power to the camera.

Secondly, you will need to use our IP finder Config Tool to find cameras on your network. For more info on basic networking knowledge as to how IP addresses matter when deploying network cameras, please read our guide about connecting security cameras to the internet.

Now, let’s discuss the three ways to to connect to an IP camera from your computer.

1.12V DC power adapter with a network cable straight into a PC

2.12V DC power to camera + network cable to router

3.Camera to PoE Switch or PoE Injector

How to Connect IP Camera to Computer

1) 12V DC power adapter with a network cable straight into a PC

a) For this method we will provide power to the camera using a 12V DC 1amp power adapter that plugs into a 110V AC outlet. Below is a picture of our trusty power adapter.

b) Next, connect a network cable from the camera to your computer.

c) Set your computer’s network port to a static IP address like 192.168.1.200 so you can talk to the camera. Here’s how you do it on a Windows Computer:

d) All newer cameras with firmware from 2018 and onward have stringent password rules that require initialization before making any configuration changes to the camera including the IP address. In order to set the password and password recovery email address you must login to the web interface of the camera. Be sure to note down and keep the credentials you are setting in a safe place that you will remember.

There are no master reset passwords for our equipment. If you forget your password, recovery email address, and security questions that you set on the camera at time of initialization, resetting the camera requires factory service which will incur out-of-warranty costs to reflash the camera.

.

e) Once you have a static IP address assigned to your computer’s wired network port, turn off WiFi on your computer. You can find the camera’s current IP address by using the Config Tool as shown. Our test camera has a current IP address of 10.1.1.65. If you need to change the IP address to let’s say 192.168.1.120, you can do that by clicking on the pencil icon to edit.

Note: if you have a password other than admin set on the cameras, then you will need to enter that in the “search settings” options before attempting to edit the IP address. See the illustration below on how that is done.

f) As explained in our article connecting security cameras to the internet, for two devices on a network to talk to each other, they must have the same IP address scheme. In 1C we set our computer’s address to 192.168.1.200, so we need to set change this camera’s address to 192.168.1.X where X is a number between 2 and 254, and not same as the our computer’s current address. We picked 12, so below is a screenshot of what to set your camera’s ip address to if you are following along in our guide. Set the subnet to 255.255.255.0 and gateway to 192.168.1.1.

g) After changing your camera’s IP address to one that matches your network, type the new IP address of your camera into the URL of internet explorer. Here’s a brief example:

You can also view the camera using our PC software. If you don’t already have it, you can download SmartPSS from here. Here’s how if you already have SmartPSS installed.

In summary, the above is a quick and easy way to connect an IP camera to a computer with a hardwired network port. This is great for the following scenarios:

• You don’t have a router and want to set up a closed circuit system between a computer and a security camera.

• You are trying to test an IP camera or troubleshoot it.

• You are trying to connect to a security video recorder directly from a computer.

Most computers have only one network port, so this method can be problematic as it would use up your only network port, preventing you from having a hard-wired Internet connection. The next 2 methods will demonstrate how to set up a network camera on a network. Method 2 is for setting up a camera with a 12V DC power supply and Method 3 entails using a PoE injector or switch. The only different between these two methods is how power is supplied to the camera.

2) 12V DC power to camera + network cable to router

This method will show you how to connect an IP camera to your router and view it over a network, while supplying power to the camera using a 12V DC power adaptor.

a) Connect a 12V DC power supply to your camera and connect the power adaptor to the wall to power the camera.

b) Connect a network (Ethernet) cable from the camera to the router to establish a data connection between the camera and the router.

c) Give the camera about 2-3 minutes to boot. Use our IP Finder Config Tool to find the camera on your local area network (LAN).  Below is a screen shot of how it looks in our case.

The camera currently has an IP address of 10.1.1.65. As explained in our article connecting security cameras to the internet, for the camera to be reachable from the computer on your network, its IP address has to match the IP scheme of your network. In our case our router IP is 192.168.1.1, so we are going to have to change the IP address of the camera. To change the IP simple press the pencil icon to edit.

d) We are going to set the camera to an IP of 192.168.1.X, we chose 192.168.1.12. Before we go ahead and change the IP address, we have to think about duplicate IP addresses on the network which would create networking issues. To see if a specific IP address is available on your LAN, use the command prompt in Windows to ping the address you intend to use. Below is a video explaining how to use the ping command. You can use this command on Mac as well by using the terminal.

e) Let’s change the IP address. In our case we set it to 192.168.1.12. Subnet mask is usually 255.255.255.0 on simple networks, and the gateway is the IP address of the router. Press OK.

f)  Once the camera is assigned a new IP address, you can access the camera using your Web Browser or SmartPSS as shown in 1F above.

3) Camera to PoE Switch or PoE Injector

We discussed that PoE supplies power to the camera, so a 12V power adapter is not necessary in this scenario.

In this method you plug an ethernet cable from the camera to a PoE port on a compatible PoE switch or injector. The PoE switch or injector connects to the router.

Here’s how you connect to a PoE switch.

Here’s how you connect to a PoE injector

Again, use the Config Tool to find your camera’s IP address and change it to match your network scheme (if necessary) as described in steps 2C thru 2E. Once the camera is on the same network as your computer you can login and watch the camera as shown in Step 1F.

.

Summary

At this point, you now should know a good amount about networking and have used the above mentioned steps to make your very own IP camera system using your computer and IP camera.

Viewing an IP Camera on a Smart TV

Among the many different ways that security cameras are used, we are often asked if it is possible to view an IP camera directly on a Smart TV without using a NVR recorder. With most Smart TVs on the market there is no application that is available to watch IP cameras directly on the TV. In this guide we show how to use an Android TV box by downloading an App to connect an IP camera to a Smart TV or any monitor that has an HDMI input.

All IP cameras from CCTV Camera World support a RTSP video stream that is usable by third party programs and apps. The App that we suggest you use on an Android TV box is called VLC Media Player. You can login and access the RTSP stream from an IP camera and have it display on a TV.

Keep in mind any device that can download VLC Media Player can do this process like iPhones, iPads, Android tablets, and phones.

What equipment is needed?

Here’s the list of all the equipment that is needed to connect an IP camera to a Smart TV.

1.IP camera from CCTV Camera World

2.PoE injector or 12V DC Power Adaptor to power the camera

3.Network cables to connect the camera to your computer network

4.Android TV Box from any online shopping marketplace

5.Computer network to connect the camera and Android TV Box

6.Internet connection to setup and install Apps on the Android TV box which can later be removed after the setup process is finished

7.SmartTV or Computer Monitor with HDMI input

.

How to connect IP security cameras to an Android TV Box

Before you can access the stream from the camera you will need to have it connected to your computer network and verify that it’s accessible. If you purchased a standalone IP camera from CCTV Camera World the camera is likely already configured with an IP address. Check the top of the camera box for the login information label. If the camera has not been configured, or you need to set it up on your network we recommend following our How to Connect an IP Camera guide.

You will also need to set up your Android TV box on your network, consult with the manufacturer of your box to find out how to do this.

You will need your IP address, username, and password that is set on the camera in order to access it. Inside of the VLC Media Player app you can access network streams. Inside of the app navigate to adding a video source and select network stream. Using the example RTSP stream below plug in the information for your camera’s IP address and type the text into the media player URL.

rtsp://192.168.1.109:554/cam/realmonitor?channel=1&subtype=0

After you’ve typed in the correct RTSP stream for your camera you will be required to login to your camera stream. Type in the username and password for your camera to allow the app to login to your camera stream.

If you receive an error, double check that your camera is connected to the network and you’ve typed the correct username and password. Provided the camera is set up on the network and you are able to login you should now see your camera stream inside of the VLC Media Player App.

Keep in mind that Smart Camera features cannot be used with the RTSP stream. If you would like to use Smart Detection features that your security camera may have, you will want to use an NVR to display the camera on your TV.

Watch our video below that shows the setup process described above on an Android TV box.

.

.

Unlimited Access Anywhere, Anytime

When you combine our “Blue Line” IP Cameras with one of our compatible IP camera network video recorders you can keep an eye on your assets no matter where you are. Take advantage of the free remote viewing app to view on your cell. Use the free software to view and control you cameras on your tablet, or computer. Stay connected and have peace of mind knowing you can monitor your cameras remotely, without any additional monthly fees.

LATEST FIRMWARE UPDATES FOR YOUR DEVICE

UPDATING YOUR SECURITY CAMERA FIRMWARE

Firmware Updates

In order to do a firmware update you must first identify the EXACT model number of your DVR or NVR unit. The model number can be found on the sticker located on the bottom or side of the unit. All CCTV Security Pros model numbers begin with the prefix “CSP” (Example, CSP-XXXX). Please match your model number to the list provided below. You will also need to locate your order confirmation email to determine when the unit was purchased. Once you have identified the correct model number and firmware please continue by following the instructions below.

Blue Line IP Camera Troubleshooting v2

Upgrading Your Firmware

Please identify the correct model from the list of firmware provided below.

Please select the appropriate link and download the .bin file. Once the download is completed copy the .bin file to a USB Flash/Thumb Drive. We suggest formatting your USB drive to FAT32 before attempting the update.

**Note : Units with Build Dates of 2013 or earlier may require you to rename the file to “update.bin” before launching the upgrade.

Once the .bin file has been transferred onto your drive you can insert the USB Drive into either of the two USB ports found on your unit. One can be found on the front panel and one can be found on the rear of the unit.

Once the drive is inserted into the unit go to the following menu:

Main Menu –> Setting –> System –> Upgrade. Click Start. Find and select the .bin file you transferred to the USB Drive and Click Start.

*NOTE – On select models you will need to go to:

Main Menu–> Info –> Version –> Upgrade

The unit will now begin upgrading to the latest Firmware Revision that is available for your device. Once completed the system will reboot. After the reboot we recommend doing the following:

1) Remove the USB Drive from your system.

2) Change your passwords on your “admin” account. For assistance in altering your password please follow this link: https://www.cctvsecuritypros.com/content/pdfs/password-account-settings.pdf

.

IMPORTANT: If you are having difficulty identifying the correct firmware please email us at support@cctvsecuritypros.com with your order number and unit model number.

User Account Locked

Your system will lock itself out when you or someone else has attempted to log into your DVR

with an incorrect user/password combination more than three times within 30 minutes

When this happens you have two options.

1. Wait 30 minutes after the last failed login attempt and try again.

2. Reboot the DVR by using the rear toggle switch or by unplugging.

When the unit powers back on try and login with the default username and passwords.

Username: admin

Password: admin

or

Username: 888888

Password: 888888

If neither of these passwords get you into your system you will need to email us at

Support@CCTVSecurityPros.com

and request a Master Password. Once we can confirm your

account we will happily be able to provide you with the correct login credentials.

Please have your Order Number or DVR/NVR Model Number when requesting a Master

Password.

*Note: The DVR/NVR Model Number can be found on the Bottom or Side of your system.

.

IP Camera Harness Repair

If your connector looks like the ones below, moisture has gotten into your RJ45 connector. The number one cause of premature IP camera failure has to do with improper weatherproofing techniques. If caught early enough a simple cotton swab and rubbing alcohol will clean that connector right up! You may need to resort to some heavier duty electrical contact cleaner if the cotton swab method does not work.

If all else fails and the connector is too far gone and cleaning it will not work, you will need to perform a harness repair.

.

In order to perform the repair you will need:

.

.

1 x RJ45 Crimp Tool1 x Male RJ45  1 x Female to Female RJ45

Connector

.

1 x Your choice of weatherproofing ( Weatherproof junction box or weatherproof Female to Female connection)

.

.

Start by removing the RJ45 end off of your IP cameras harness. Be sure

.

Strip back the outside insulation to expose the internal cables.

.

Organize the cables to match the pinout of the IP camera. Slide the organized cables into the connector and crimp. All CCTV Security Pros IP cameras will use this pinout.

Connect your Female to Female RJ45 connector to check your work, you should have a functioning IP camera now that its void of all corrision.

Now that the IP camera has been repaired we still need to weatherproof this connection. It is now more vulnerable than ever!

Consider using a weatherproof junction box to make your connections in, or perhaps a weatherproof Female to Female connector.

Remember that different coupling styles exist so make sure that you are informed about how to use the coupler before you start crimping wires.

Troubleshooting Steps 4/8/16 Channel

(Cannot Find the Network Host)

To solve the error, please verify that the camera is properly plugged into the back of the system. If you unplug and re-plug it back in this should verify it is connected physically.

If the issue continues go to Main Menu > Camera > Camera List and delete the camera with the red status from the bottom list and do a Device Search to verify the camera is showing up on the top list.

If the camera does not show up this means the cable is not connecting properly, which could either mean the camera is not getting power or isn’t transmitting data. The best way to determine whether it is an issue with the Camera or Cable is to bench test the camera on a known working cable.

If it does show up but it has a different IP Address, please confirm the IP Address is in the 10.1.1.1-255 range (This is the default range of the internal Switch).

If the camera is not within the correct IP range, then the camera could need to be modified on the top list to properly connect in which you would select the camera, hit modify, type in the camera’s username and password and set the IP address to DHCP to automatically obtain an IP or statically assign the camera an IP address to match your switch range and gateway.

If the camera is on the correct range, you should be able to add it to the bottom list and it will come up with Green or Red, If Red double check the error message on the live view on the system.

If the Error says Invalid Username or Password, go back to Settings > Camera > Camera List and modify the camera at the bottom of the list and type in the correct login information.

If the error says Cannot Find the Network Host, check the IP Address is in the correct range, if it is you need to verify your cable is good by testing the camera with another known good cable or testing on a short patch cable as the cable could be experiencing packet loss.

Make sure the cable is T568B Standard and is within 100 meters (328 feet.)

Night Vision Issues

When a camera goes into night vision mode, the infrared LEDs around the lens turn on. If the video signal at nighttime or in dark locations is washed out, foggy or you see “halos” on the screen it is because the infrared LEDs are reflecting back into the camera lens.

cameras LEDs to focalize on the mounting surface and greatly reduce the Infrared distance.

Adding 3rd Party Cameras to Blue Line NVR

We always recommend using Blue Line IP cameras with our Blue Line NVRs for the easiest and most complete experience possible. However, we understand that using 3rd Party Cameras can be beneficial in some applications. This guide will explain the basics of adding a 3rd Party IP camera into your Blue Line NVR.

Information you will need to add 3rd Party Cameras.

With your camera attached to one of the PoE ports on your NVR, you’ll navigate to the camera settings from the main menu.

A 3rd Party Camera normally will not add itself, so you will need to go into the Camera List and click on Search Device. If the camera is detected, you will be able to select it and click on the Modify IP button toward the middle of the screen.

When modifying the IP address of the camera the default IP range for the PoE ports on the NVR is

10.1.1.xxx so you’ll want to make sure the camera is on the same range.

You will need to know the camera’s password to change the IP Address. Once the IP is successfully changed it should update after clicking Search Device again

Check the box to the left of the camera and click Add. Most cameras will show up with the Manufacturer as ONVIF. If they do not and show up as red, you will need to click on the edit button on the camera and change the Manufacturer to match the camera’s manufacturer, or to ONVIF if the manufacturer of the camera is not listed.

While in the modify window you can also enter the password for the camera in the password field. Once that is completed you can click OK. After a few seconds the status should change to a green icon and then you should be able to see the camera’s live view. Please keep in mind that if the Error Message says Invalid Username or Password you may need to login to the camera from the Web and setup an Onvif User for the system to login with.

If the camera is still showing offline, setting the manufacturer to PELCO can sometimes resolve the issue.

Additional 3rd Party Camera Information

DVR/NVR Rebooting

If your DVR or NVR is rebooting by itself please read the guide below.

If your DVR or NVR is rebooting once a week this is completely normal. Our DVR and NVR systems are designed to reboot once a week (Tuesday at 2AM by default).

If your DVR or NVR is rebooting more frequently you first want to check the power source of the DVR or NVR.

Be sure you are using the correct Power Source that was included with the DVR or NVR. Below are the correct power adapter specs so you can identify the correct one.

NVRCUBE = 12V, 2.0Amp NVRWIFI = 12V, 2.0Amp

LITE Series DVR = 12V, 2.0Amp

Pro Series DVR = 12V, 5.0Amp

Pro Series NVR = 3 Prong Power Cord to Power Outlet Extreme Series DVR/NVR = 3 Prong Power Cord to Power Outlet

If you can confirm you are using the correct Power Adapter you may need to double check the outlet you are plugged into. Try an alternate outlet and eliminate any Battery Backup Power Supplies for test purposes.

If the power source is not causing the reboot cycle it could be related to the internal hard drive. To check this out please continue reading.

First you will need to Power Off the DVR. We suggest powering the system down from the Power Switch on the rear of the system or by simply unplugging the Power Cable.

Once the system has been powered down you will need to open up the system. Please see below to locate the screws that need to be removed.

NVRCUBE or NVRWIFI

There will be 4 Phillips head screws located on the bottom of the system. Once the screws are removed the top cover will lift off.

Lite Series DVR

There are 2 Phillips head screws located in the rear and 2 on the side of the DVR, 1 on each side. Once the screws are removed the top cover will lift off.

Pro Series DVR/NVR

There will be 4 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Extreme Series DVR/NVR

There will be 2 Phillips head screws located on the rear of the system. Once the screws are removed the top cover will slide towards the rear and lift off.

Once the top cover has been removed it will expose the Hard Drive and its connections.

First we want to Unplug the Large Black Connector. Press down on the metal tab and pull the connector out of the Hard Drive.

Now we want to unplug the second smaller connector (Blue Cable) from both ends. Press down on the tab and remove from the Hard Drive as well as the System Board.

Once the connections have been disconnected. Plug them back in securely and listen for the metal tab to click. This will ensure a good connection in between the System Board and Hard Drive.

Note*

While you still have the system open, it might be a good idea to check the cooling fans for any dust or debris that could be stopping the fan from moving. This could cause the DVR or NVR to overheat.

Once the connections are tight, lets put the top cover back on. When the cover is back on you can proceed to power on the system. Once the system is powered on you will need to monitor the system and check if it is still rebooting.

Disconnecting The Internet

If the system is still rebooting you may want to disconnect it from your Router or Modem by unplugging the Ethernet cable in the rear. You will loose your remote viewing capabilities temporarily while unplugged but can help us diagnose the issue.

With the cable unplugged you may want to monitor the system closely to see if this has made any changes to the rebooting issue.

Disconnecting Cameras and Other Sources

Disconnecting cameras, alarms, extra monitors and microphones is the last thing we can try to solve your rebooting issues.

Cameras, monitors, and microphones mounted near high voltage could be causing your system to reboot by itself. If your system detects any incoming voltage or amperage coming into the rear inputs the system will shut down to protect itself from damage.

Leave your main Display Monitor and Power Source connected. Disconnect one input at a time to see if it makes a change in your reboot cycle. If you notice a change in the rebooting you can single it out by using this method of elimination.

How To Setup a Security Camera System?

The first phase in setup of a security camera system consists of installing the cameras and running the wire. The second phase is completing the connections between the cameras and the recorder, which depends on the type of camera system you have purchased.

How To Setup a DVR Camera System

DVR camera systems consist of security cameras that have BNC jacks to send video over coax wire, and a 12VDC power connector for power. Such coax wire based systems use RG59U siamese cables that have BNC and 12VDC power connectors at each end, which allow video and power to be run together over one “siamese cable.” As shown in the setup video below, BNC connectors are silver colored metal connectors that twist lock on to the video jacks of a camera and DVR recorder.

Infrequently, an installer may use network cabling with video baluns instead of coax cabling, which was very common with older CCTV systems to transmit video signal over long distances. Regardless of whether you are using coax wire or video baluns, setup of a DVR camera system is similar as demonstrated in the following video:

How To Setup a NVR Camera System

NVR camera systems use plug-and-play IP Cameras that connect directly to built-in PoE ports on the back of the NVR. Such systems are also commonly referred to as PoE IP camera systems because the cameras use Power over Ethernet technology to send power/video/data all over one network cable. We recommend using CAT5e cable as a minimum, and CAT6 wire is recommended for runs longer than 150ft as its thicker wire gauge allows for improved power transmission.

Our IP camera systems feature plug-and-play compatibility between the NVR and IP camera. Unless otherwise specified, we ensure the cameras and NVR we sell are compatible with each other and allow even a novice user to setup a IP security camera system.

To gain a good understanding of your purchase, we recommend customers bench test IP cameras with the NVR recorder before installing the cameras. Once it is established that all cameras are operational, continue with mounting the cameras at the desired location and running the camera wire. Since installation errors are common when crimping CAT5e or CAT6 network cable, we recommend using a cable continuity tester to safeguard against wiring related issues.

As each camera is installed and connected to its wire, follow the video below to learn how to connect each IP camera to the NVR in a NVR camera system.

Once cameras are installed and wired to the digital video recorder it is time to login, and start using the system, which leads us to the third phase

How to use your surveillance system

1. How To Login to a Security Camera System

Before you are able to login to your camera system over the web, you need to login at the DVR or NVR itself using a mouse. Connect the recorder to a monitor that supports at least 1080P resolution. We recommend using a HDMI input capable monitor. Turn on the recorder and login using two possible login methods.

Please watch the video below to learn more from our video tutorial about the two different ways to login to your or security system.

In case you are unable to login due to a forgotten password, it is easy and secure to reset the password and gain entry into the unit. It is required that you be present at the recorder when following the video guide below on how to reset the login password. As shown in the video below, by answering some simple security questions you can quickly reset the login password.

2. Viewing Live Video and Audio on a Security System

All of our DVR Systems and HD NVR systems allow multiple viewing options. You can view multiple cameras in a grid-view or view one camera at a time in full screen mode. Full screen mode also allows the user to listen to audio from security cameras with built-in microphone. To hear audio from cameras, all of the following conditions must be met:

For a comprehensive guide of the different viewing options offered by our security camera systems, please watch the following video:

Regardless of whether you have an IP security camera system or DVR camera system, both provide the user with two types of zoom:

It is important to understand the difference between digital zoom and optical zoom, and the fact that optical zoom can only be used in live view mode. Below is a detailed video demonstration of each type of zoom function and how both can be utilized during live view to see objects far away. Using a 4MP security camera mounted 7ft above the object of interest, we show the power of optical zoom provided by a motorized zoom security camera to view objects in fine detail.

If your system has motorized zoom cameras or a outdoor PTZ camera that you purchased from CCTV Camera World, they can be easily controlled using our surveillance video recorders. Regardless of whether the motorized cameras are HDCVI or IP cameras, or whether your recorder is a DVR, XVR, or NVR, the cameras can be controlled using the friendly GUI interface of our systems as shown in the following video.

3. Setting Recording Resolution

A common misconception about our camera systems is that all cameras have to be the same resolution, which is not the case. Cameras of different resolutions can be used on the same recorder in any of our systems, granted the cameras are within the maximum resolution limit of the recorder. This is true for systems consisting of Tribrid DVR, XVR, or NVR recorders.
Encoding settings can be set individually for each camera channel. Depending on the maximum recording resolution supported by the recorder and the camera, our surveillance recorders allow up to 12MP recordings. All of our DVR and NVR recorders also have dual video encoding technology to provide two streams of video for each camera channel:

The Encoding menu has several settings that can be set. A good understanding of the following settings is important in getting the most out of our security camera system purchase from CCTV Camera World.

The in-depth video tutorial below discusses encoding settings available in your system and how to configure them.

4. Customizing Video Settings

We manufacture our cameras to produce the best possible picture quality automatically. Sometimes peculiar lighting scenarios in a scene may require customization. Our DVRs and NVRs allow multiple picture quality settings to be modified from the recorder as explained in the detailed video tutorial below. It is important to note that there is a difference in capabilities to modify image settings when comparing coax based cameras versus IP cameras.

Coax based cameras produce video that is encoded by the DVR, thus allowing picture quality to be modified before the video is saved by the DVR. In contrast, IP cameras encode video that is streamed to the NVR for saving the video stream; the video is not encoded by the NVR. Therefore, any changes made in the picture settings on the NVR must be communicated back to the IP security camera. If an incompatible IP camera is used with an NVR, such changes will not be communicated to the IP camera, and changes will not apply before video is encoded by the camera.

Our systems allow a wide variety of picture settings to be toggled depending on the camera specifications. In addition to picture brightness and contrast, the user can toggle image quality features such as backlighting, glare compensation (WDR), and image flip.

https://youtu.be/zW3g-dTV30w

5. Recording Method Configuration

All of our security systems offer a variety of video recording methods. Each security camera can be set to record independently and the user has the option to choose from the following recording methods:

The digital video recorders in our systems even allow multiple recording methods for each camera. For example, cameras can be set to record all the time or during a portion of the day using the scheduled recording method, while also recording upon motion detection. This preserves video integrity in case a motion event is missed, and is very helpful when reviewing recorded security footage to allow the user to skip to points in the timeline when motion is detected. The video tutorial below is an in-depth guide on how to set the different recording methods for each camera in your surveillance system.

https://youtu.be/jRfV3N8sAqY

6. Playback Recorded Video on your Surveillance System

CCTV Camera World’s security camera systems have a user-intuitive graphical interface to playback recorded video. Using a mouse connected to your recorder, it is easy to review recorded security footage in the Search menu. It takes 3 simple clicks to playback recorded video:

The video above is a comprehensive tutorial on how to playback recorded video, in which we cover:

You can playback one camera or multiple cameras depending on the resolution of the recording and the playback capability of the recorder that is part of your system. Our 4000 series NVRs support playback of up to eight 1080P channels, while our 5000 series NVR support up to sixteen channel playback at 1080P. Stronger playback capability is available when playing video over the network using our free computer client software to playback video on a PC or Mac workstation.

7. How to Download Video from a Security Camera System

When there is an incident, it’s important to have a camera system that allows easy download of security footage catching the perpetrator in the act. Our security camera systems are based on this simple principle to allow easy video download of a short video segment to a USB drive and playback on a Windows or Mac computer. To download video from any of our standalone recorders you will need a USB flash drive that is formatted with the NTFS or FAT  file system. The flash drive should not be more than 256GB. The video guide below on how to download footage from your security camera system walks you through the process.

Briefly, below is a list of simple steps on how to download video from a DVR Camera System or HD IP Camera System purchased from CCTV Camera World.

8. How To View Downloaded Footage from a Security Camera System

Once security footage has been downloaded from your surveillance system, it can be reviewed on a Windows or Mac OS computer using our free playback software called Smart Player. You can download it here for Windows and Mac. Here is a list of features of Smart Player which makes our systems one of the best security camera systems in the industry for video archiving and review:

.

Upgrade your DVR Security System

If you have a camera security system that is wired for coaxial and you cannot run Ethernet, you can connect our Coaxial to Ethernet Converter Kit. This enables upgrading your analog system to IP while still using existing coaxial cabling. The converters are small, lightweight, easy to install, and do not need to be connected to an additional power adapter. There is no need to run new cabling, simply plug the converters in. Send data and power over coax up to 900 m (2,952 ft) reach (performance and supported length are subject to transmission coaxial cable and coupler quality). This is a cost-effective and useful solution for legacy DVR upgrades and future expansion.

.

Coaxial to Ethernet Converters

To upgrade your wired system to an NVR with IP security cameras, you will need:

or

Features:

Easily Connect IP Cameras Over Existing Coaxial Cabling

Also Read : How to use Webcam on Surveillance Station on QNAP NAS?.

Installing your Coaxial to Ethernet Converters

Safety Precautions

Please read the following safeguards and warnings carefully before using the product in order to avoid damages or losses:

 WARNING: Do not use power line other than the one specified. Please use it properly. Otherwise, it may cause fire or electric shock.

Installation

.

Product Overview & LED Indicators

.

Mounting

The Coaxial to Ethernet Converter supports two installation modes: junction box or it can support DIN rail mount.

Note: Supports slide width of 28 mm (1.1”)

For full mounting instructions, please refer to the junction box’s Quick Start Guide on Lorex’s support page.

.

Product Specifications

.

PoE Power Supply Specifications (RG59 Coaxial Cable)

ePoE switch supply voltage 48V. / RG-59, max. DC resistance < 5 Ω / 100 m (328 ft)

ePoE switch supply voltage 53V. / RG-59, max. DC resistance < 5 Ω / 100 m (328 ft)

4K IP Wired Dome Security Camera with Smart Deterrence: Installation

This article provides instructions on how to install and connect 4K Smart Deterrence IP Dome Camera with Smart Motion Detection Plus (E893DD Series) to the NVR.

.

Before Installing

.

Installing 4K Smart Deterrence IP Dome Camera

.

Connecting 4K Smart Deterrence IP Dome Camera

Connect the cameras and cables to your NVR using one of the following two setup methods.

1. Connect cameras directly to the NVR (recommended)

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to the NVR’s PoE ports. The camera may take a minute to power on after being connected.

Note: A 12V DC power adapter (model#: ACCPWR12V1, not included) is only required if connecting the camera’s Ethernet cable to a router or switch that does not support PoE.

Notes:

2. Connect cameras to a PoE switch or router on your network (not included)

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to a router or switch on your network. See your NVR manual for details on connecting the camera to your NVR using a router or switch.

.

Using the RJ45 cable gland (optional)

The pre-attached RJ45 cable gland covers both the camera’s Ethernet connector and the RJ45 plug to provide weather-resistance and protection from dust, dirt and other environmental contaminants.

To use the RJ45 cable gland, twist the RJ45 cable gland barrel securely onto the camera’s Ethernet connector.

Tip: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for additional sealing if it will be exposed to precipitation regularly.

Cable extension options

You can extend the Ethernet cable run for your camera up to 300ft (91m). To extend the cable run beyond 300ft (91m), a switch will be required (sold separately). Use an RJ45 coupler or a network switch (not included) to connect male ends of Ethernet cables together. We recommend using UL CMR approved cables available at lorex.com.

4K IP Wired Dome Security Camera with Smart Deterrence: Getting Started

This article provides instructions on how to setup the 4K Smart Deterrence IP Dome Camera with Smart Motion Detection Plus (E893DD Series).

.

Important Installation Guidelines

The optimal installation location, including the height and angle of your camera, will depend on the type of detection settings that you want to enable. Since the optimal angle for person and vehicle detection is different from the optimal angle for face detection, you will need to select one approach.

Note: You cannot enable both face detection and person and vehicle detection at the same time.

Based on your detection preference choose between:

1. Optimizing person and vehicle detection accuracy

2. Optimizing face and mask detection accuracy

Note: Facial recording without consent is illegal in certain jurisdictions. Lorex Technology does not assume liability for any use of its product that fails to conform with local laws.

High accuracy Vs. low accuracy face detection

Accuracy will be influenced by lighting conditions and the distance/angle of a person’s face to the camera.

Mask detection

With face detection enabled, you can set the alarm type to detect if a person is not wearing a mask. A person not wearing a mask or improperly wearing a mask will be captured in the face preview sidebar and a notification will be sent through the Lorex App.

.

For full instructions on installing and connecting the 4K Smart Deterrence IP Dome Camera to the NVR, visit Installing 4K Smart Deterrence IP Dome Camera.

4K Ultra HD Smart Deterrence IP Camera: Installation Guide

This article provides instructions on how to install and connect 4K Ultra HD Smart Deterrence IP Camera (E893AB Series) to the NVR.

.

Before Installing

.

Installing 4K Ultra HD Smart Deterrence IP Camera

.

Connecting 4K Ultra HD Smart Deterrence IP Camera

Connect the cameras and cables to your NVR using one of the following two setup methods.

1. Connect cameras directly to the NVR (recommended).

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to the NVR’s PoE ports. The camera may take a minute to power on after being connected.

Note: A 12V DC power adapter (model#: ACCPWR12V1, not included) is only required if connecting the camera’s Ethernet cable to a router or switch that does not support PoE.

Notes:

2. Connect cameras to a PoE switch or router on your network (not included).

Connect the Ethernet cable to the camera and then connect the other end of the Ethernet cable to a router or switch on your network. See your NVR manual for details on connecting the camera to your NVR using a router or switch.

.

Using the RJ45 cable gland (optional)

The pre-attached RJ45 cable gland covers both the camera’s Ethernet connector and the RJ45 plug to provide weather-resistance and protection from dust, dirt and other environmental contaminants.

To use the RJ45 cable gland, twist the RJ45 cable gland barrel securely onto the camera’s Ethernet connector.

Tip: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for additional sealing if it will be exposed to precipitation regularly.

Cable extension options

You can extend the Ethernet cable run for your camera up to 300ft (91m). To extend the cable run beyond 300ft (91m), a switch will be required (sold separately). Use an RJ45 coupler or a network switch (not included) to connect male ends of Ethernet cables together. We recommend using UL CMR approved cables available at lorex.com.

.

Overview

Video surveillance systems can sometimes be too expensive and difficult to maintain for general home users. By supporting webcam monitoring & recording, QNAP Turbo NAS offers an affordable and easy-to-use option for home and small office security. The Surveillance Station app on Turbo NAS is capable of 24/7 recording, taking screenshots, and allows you to remotely view live video streams and recorded files anytime, anywhere.

.

Webcam surveillance requirements

You will need a webcam with a built-in UVC (USB Video Class) driver. You may refer to the following lists for compatible webcams:

Please note:

.

How to use Webcam on Surveillance Station on QNAP NAS?

Read Also : Dahua XVR Remote Access Full Guide

Configure Surveillance Station for webcam recording

1. Connect a USB webcam

Connect a USB webcam to a USB port on the Turbo NAS. If the webcam is supported, it will be listed as a log showing a generic UVC camera in “Control Panel” > “System Settings” > “System Logs” on the NAS.

2. Install the QUSBCam QPKG from App Center (either Automatically or Manually)

Automatic installation: Install the QPKG from “App Center” > “Surveillance” > “QUSBCam” of the NAS.

Manual installation: Download the QUSBCam QPKG from the App Center on the QNAP website. Then you can install it by clicking the “Install Manually” button and by selecting the location of the QUSBCam QPKG to start installing.

3. Configure webcam in QUSBCam

First, open “QUSBCam”.

Video settings can be configured here.

4. Configure Surveillance Station

a. Install Surveillance Station

Please note: To ensure proper operations of Surveillance Station, we recommend rebooting the Turbo NAS after its installation is completed.

b. Configure the webcam on Surveillance Station with required settings: (Please check the detailed settings in QUSBCam, “HTTP URL” may vary by different situation.)

Please note: Before applying new settings, you can click “Test” on the right to check that the connection to your webcam is successful.

After you have added the USB webcam camera to your Turbo NAS, go to the “Monitor” page. If it is your first time accessing this page in your web browser, you will have to install an ActiveX control (QMon.cab) before using Monitor or Playback functions. Please follow the on-screen instructions to complete the installation. You can use Surveillance Station in Google Chrome, Mozilla Firefox and Microsoft Internet Explorer.

.

Play Video Files from Surveillance Station

Click or to enter the playback page and follow the steps below to play video files on the remote Surveillance Station.

1. Drag and drop camera(s) from the server/camera tree to the respective playback window(s) to select the channel(s) for playback.

2. Select a playback date using  You can examine each channel to discover the time range when files were recorded using each camera. Blue cells indicate regular recording files. If it is blank, it means that no files were recorded at that time.

3. Click to begin playback. You can control the speed and playback direction by dragging the buttonto left or right of the shuttle bar.

4. Specify the time to play back the recording files. You can view a preview image on the timeline bar to search for the moment you want to play.

5. Click to control all the playback windows to play back the recording files. When this function is enabled, the playback options (play, pause, stop, previous/next frame, previous/next file, speed adjustment) will be applied to all of the playback windows.

.

How to Use QUSBCam2 with USB Cameras?

.

Overview

QUSBCam2 transforms USB cameras (webcam)(*1) into IP cameras with ONVIF compatibility and full support for the RTSP protocol. Its live view does not require any extra plug-ins in your browser, and it is a handy surveillance tool for homes and small offices.

.

Requirements

How to View a Live Stream on QUSBCam2

1.Install USB Camera
After connecting the USB camera to the NAS, the USB camera appears on the USB Device page.

2.Set as channel
After installing the USB camera, go to Channel List and click “Create Channel” to create a QUSBCam2 channel.

Set the channel name and video or audio configuration.
Note: Only MJPEG format supports the live function.

3.Check the Channel List
Go to Channel List and check if the thumbnail image of the USB camera is available. If you see the  live button, it means that the camera supports the live function.

Configure Surveillance Station for Webcam Recording

Go to “Surveillance Station” > “Camera Configuration” and then click “Add”. Select “Search camera(s) automatically” and then click “Next”.

For Search type, select “ONVIF” and then select the QUSBCam2 camera. Click “OK”.

Surveillance Station automatically completes the camera information except for the user name and password. Use the same login credentials for the NAS that you are using.

Click  to launch the QVR client to see the live video and recording.

Additional Information

QNAP does not guarantee full compatibility with all USB cameras. For details on compatible USB cameras (webcam), refer to the following lists for UVC (USB Video Class):

Logitech UVC Webcam List
http://support.logitech.com/en_us/article/6471

Linux UVC Webcam List
http://www.ideasonboard.org/uvc/

There are two possible ways to reset the password with the new firmware. However both need the person to access the NVR either by being in front of it or by access in on the computer (entering the IP address on the browser). The screenshots shown on this guide will be the ones we can get on the NVR itself:

Bring up the login screen by right-clicking anywhere and clicking on the “Menu” option. When you see the login screen, click on the “Forgot Password” link:

After that, either 2 types of screens will come up: The first one is to enter an email address to get a new temporary password:

Please enter a valid email address to get your new temporary password:

The second type of screen is the same as the one it will show when we click “Next” after entering the email address:

2MN NVR XVR Troubleshooting 2024

Read Also : Xmeye Dvr System Instructıons For Use

When you reach this screen, you can follow one of the following options:

Option 1:

If you have downloaded the 2M Guard App for your phone, you can do the password reset yourself.

Click on the “Local Config” option:

Click on the “Forget Device Password” option and scan the QR code on the NVR screen:

After that, a message will appear saying that the temporary password will be sent to the registered email address:

Click on “OK” to send the password and wait for the confirmation page:

Click “OK” again and wait. The email will look like this:

Take note of the security code and enter it on the “Security Code” field of the Retrieve Password screen (The security code is case sensitive, this means that upper and lower case letters matter):

After entering the security code, press “Enter” and press “OK”. After that, a new pop-up screen will appear to enter a new password on the “Password” field. Don’t forget to enter the same new password on the “Confirm” field:

After that, click on “OK”.

Option 2:

If you don’t have the 2M Guard App downloaded, you can take a picture of the QR code shown on the “Retrieve Password” screen. Here is an example of the picture you should take.

After you take the picture, please contact Technical Support to receive more instructions. We will do the password reset using the QR code picture taken.

NOTE: Please do NOT exit from the “Retrieve Password” screen after you take the picture of the QR code. The security code only lasts for a day, so please keep that in mind before starting a password reset process.

.

How to Access Device from Web

This guide is valid for models 2MT-4004, 2MT-4008, 2MT-4088, 2MT-4016, 2MN-8004-P4, 2MN-8008-P8, 2MN-8116-P16, 2MN-8232-P16.

When devices are connected to the network, they can also be accessible from a computer. The first thing you need to make sure of is that the computer you are using and the DVR/NVR are connected to the same network (network is coming from the same router for both devices). You will first need to obtain the IP address of the DVR/NVR from Menu → System → Network → IPv4 address.

After noting the IP address of your device, open Internet Explorer and in the address search bar type in the DVR/NVR IP address. If the NVR and the computer are on the same network then it will pull up the login page of the DVR/NVR. The credentials will be the same as when you log into the local interface of your device.

How to Use the Check Template to Create Schedules

The check template supports a time range-based authentication mode with a maximum of eight time ranges available per day. This is useful if a company only wants to allow employees to enter when their shift is supposed to start and not outside of those hours.

First, you will need to create the time schedules for each day. This is done in the Check Template page under each Time Interval. You can create up to 8 different intervals per day, but it is not necessary to use all eight. You must also choose a checking method for each time interval: card, face, password, card + face. Each day of the week can have the same schedules or you can create different schedules for different days. If you choose to have the same schedule for all days, or for multiple days, just Copy To at the bottom of the screen and Copy.

Once all of the desired time intervals have been added, name the template so that it can be easily defined, and click on Save.

Now that the template(s) have been created, we need to assign each group to a schedule. Go to the Face Library and create different libraries based on each group of people that you would like to have. NOTE: Only a maximum of 16 face libraries can be set.

There are two different library types: Employee and Visitor. When you create a library, it gives you the option to choose a Check Template. This is where you will choose from one of the templates that were created earlier. If you do not choose a template at this stage, you can always edit the library at a later time.

After creating all of the necessary libraries, now you can add employees into each appropriate library. When all of the employees have been added into the right libraries with the right templates, they will only be able to enter during the specified time frame.

How can I make sure my device and computer are on the same network?

In order to access network devices from a computer, they both have to be connected on the same network. But how do you check that the settings are correct, and if they are not, how do we fix that? This article is based off of the assumption that the computer and the device are connected to the same router/network switch.

Basic Explanation of the Network

Before we begin the steps on how to configure our network, we need to understand why we are doing it. Each device within a network has its own IP address – we will use 192.168.1.13 as an example – and its structure is like this:

The host ID will be different because that is what differentiates each device from one another. Within a network, the network prefix will be the same and so should the subnet ID, but there will be sometimes where it is different on a device. If the network prefixes and subnet IDs are the same for the devices, then that means they can all reach and communicate with each other.

If either one of the two are different, then that means they are not connected and they cannot establish a connection with each other. The purpose of this article is to make sure that the network prefix and the subnet ID are the same for the computer and your device so that you can create a connection and reach the device.

Checking the Network of the Computer and Your Device

The easiest and fastest way to check the network of your computer is to open up the command prompt. Open the Windows menu and type in “cmd” for command prompt.

Once the window is open, type in “ipconfig” and hit Enter. This will pull up the basic network information of your computer. Make note of the IPv4 address and the default gateway. Now that you have found the IP of the computer, please find the IP of your device – the method to obtaining the IP address might be different for each device. As mentioned above, if the network prefix and the subnet ID are the same for both the computer and your device, then they will be able to communicate with each other. If they are different, then please follow the steps as below:

Changing the Network of Either the Computer or Your Device

The most simple solution to allow both devices to be on the same subnet is to edit the IP address of your device. Usually, you just need to disable DHCP and enable a static IP address. But this is not always possible depending on the set up. NOTE: The computer must be connected with Ethernet in order for this configuration to work. It will not work through Wi-Fi.

In order to change the network of your computer, you will need to go to the Network and Sharing Center. On Windows 10 operating systems, it can be reached by either the Control Panel or from the Taskbar. In the Sharing Center you will be able to see all Connections the computer has. Click on the correct Ethernet connection.

After clicking on the Ethernet connection the Ethernet Status window will pop up. Click on Properties → double-click on Internet Protocol Version 4 (TCP/IPv4). By default, your computer will be set to “Obtain an IP address automatically”, but we will want to change it to Use the following IP address. Remember in the steps above that we found out the IPv4 address of the computer through the command prompt. This is where it will come in handy again. When you select Use the following IP address the boxes below will become active. The information will be as follows:

Once all of that information is filled out, click on Advanced in the bottom-right corner of the window, and it will open up the Advanced TCP/IP Settings where you will Add a new TCP/IP address. Please make sure the new TCP/IP address will match the subnet as the device you are trying to access, or else it will still not connect. NOTE: Please do not use the same IP address as the device. The Network Prefix and Subnet ID should be the same, but the Host ID should be different.

Adding the Subnet Mask can be easily done by hitting Tab after inputting the IP address because the fields will automatically be filled afterwards. Click Add after entering the correct information, and then just keep clicking okay until you are back at the Ethernet Status window. Then close the window.

You can check if the configuration was done properly by opening the command prompt and pinging the device’s IP address. You can do this with the prompt: ping IP address. For example: We are using the IP address 192.168.0.10 for the device. Enter the command prompt and type ping 192.168.0.10. If you receive a response, that means the configuration was done correctly, and you may now access your device.

How to Use External QR Scanner

This article is applicable to the facial recognition temperature scanners which are models 2MTHFR-2M or 2MWTK.

.

How to reset the password to your Gamut recorder

This article will show you how to find the necessary information you need to send us so that we can help to reset the password for your Gamut recorder.

.

First, turn the recorder on and move your mouse to the bottom of the camera live view screen. A blue bar will appear at the bottom; click on the ‘i’ symbol that I have marked in red in the screenshot below.

.

.

This will open up a page of information about the recorder including the MAC address.

.

.

You will need to send the MAC address and the date and time on the recorder, even if the time/date on the recorder is not actually correct. 

.

This is very important, because we will generate a temporary password for you which is created based on the unique MAC address of the device and the time and date on it. If the date and time are accurate, just say that, or if you know it is five hours behind but the date is correct for example, just mention that when you email in and that should be sufficient. 

.

Otherwise, just send in a picture clearly showing the MAC address and date/time on the device and say exactly when the picture was taken.

.

Get in contact here, set the support status as ‘Password reset’ and the email subject as ‘Gamut password reset’. You will also need to send your original order/invoice number and the original delivery postcode to confirm your identity.

We will try to get back to you as soon as possible.

How to set up and view your Gamut PTZ on a Windows or Apple computer (GTIP210PTZ)

Purpose of The Guide

This guide will walk you through the initial configuration of your Gamut PTZ and show you how to view the camera on your computer.

.

Before You Begin

Let’s Get Started

First we need to make sure that the camera is talking to your network. If you look on the box for the camera and on the side of the camera itself you should see a sticker that looks something like the one shown below.

.

.

Make a note of the IP Address, User name and any Password shown on the sticker.

.

Next we need to open Internet Explorer on the computer. In the address bar at the top of the page enter the IP address that you saw on the sticker. You should then be prompted to log in to the camera, here you need to use the User name and Password shown on the sticker, if there is no password on the sticker then leave the password field blank.

.

Please make sure that you are using Internet Explorer and not any other browser. The reason for this is that most CCTV systems require the use of software called Active X to be able to display your live video and that software is only supported by Internet Explorer.

.

If you are prompted to install any software you need to allow this to happen, this software enables your computer to display the video feed from the camera.

.

At this point you should be seeing a live view from your camera and can go ahead and fit your camera wherever you need it. To watch your cameras in future you will simply need to open Internet Explorer, go to the IP Address from before and log in to the camera. From there you can also control the motion of the camera by using the PTZ controls shown below. These features are explained more in depth in other guides which can be found here.

.

If you were unable to access your camera this way then it’s not a problem, we just need to use a different method. Alternatively if you wish to view the system without having to log in through Internet Explorer each time then continue reading and you will see how to view the camera without needing to log in each time.

.

First open CMS5/VMS, the program that you installed before we began, and click on Device Manager. You will now be presented with a screen that looks like this:

.

.

You should see a camera in the list that has the same IP Address as previously seen on the sticker on the camera. If you don’t then click the IPV4 Search button and after a few moments the camera will appear. Select the camera by ticking the box to the left of it and click Add.

.

The camera will now be displayed in the bottom half of the window. Towards the right hand side you will see a number of buttons, you need to press the Modify IP button as highlighted in the following image.

.

.

At this point if you wish to use the camera through Internet Explorer rather than CMS5 you are now able to. Make a note of the new IP address that the camera is displaying and follow the steps detailed near the top of this guide for accessing the camera using Internet Explorer.

.

Now click the Home button to return to the main page for CMS5/VMS, then click Monitor. On the right hand side you will see your camera in the list of devices. Double click on your camera and the video feed will appear in the middle of the screen. If you then double click on the video if will go in to full screen mode so you can see a larger picture. To then control your camera click the button shown below and the PTZ controls will appear. As before more articles about controlling your camera can be found by clicking here.

.

GAMUT RECORDER Installation and user guide

Read More : UNV Recorder Set Up Guide

How to add your Gamut recorder or camera to a mobile phone or tablet

Purpose of The Guide

This guide will show you how to add your Gamut camera or recorder to a phone.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. If you have a recorder with a hard drive you will need to use a TV or Internet Explorer to set it up for the first time, follow the quick start guide to do so.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

You will need to download the app RXCamView onto your phone or tablet.

Android

.

Apple

.

Let’s Get Started

Open up RXCamView on your device and tap on the head and shoulders icon to open the side menu.

.

Then tap on ‘Device List’.

.

.

On the Device Manager page, tap on the ‘+’ icon then tap on ‘IPC/NVR/DVR’.

.

.

The app will request permission to use your camera, allow it to. It will open up your camera and you need to point the camera to the QR code on the label on your recorder or camera.

.

.

Once you have successfully scanned the QR code the app will prompt you to fill in some information. Leave the IP/Address and Media Port fields, the username is admin by default, and the password is blank by default.

.

Then the device will appear in the device list, it should say ‘Connected’. If it says ‘connect close’ then check the password is correct and that nothing has been disconnected.

.

.

If you tap on the play icon underneath the device, you will be taken to the live view window. Just tap on the name of the device to begin live view.

.

.

To view recordings, just tap on the film reel icon at the bottom right below the live view screen:

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

.

If you find that the device only works when you are connected to the same internet router as it, and not when accessing it via another Wi-Fi network or with 4G, take a look at this guide.

How to access your Gamut camera or recorder using a Windows or Mac computer

Purpose of The Guide

This guide will show you how to access the live footage, recordings and settings of your Gamut camera or recorder, using a Windows or Mac computer.

.

Before You Begin

Your Gamut device will need to be turned on and connected to your internet router. You will need to use a TV to set up the recorder for the first time, follow the quick start guide to do so. After the initial setup, a TV or monitor is not necessary when accessing the recorder via a network connection.

.

If you are using a recorder and cameras, make sure that the cameras are connected and working.

.

If you are using a Wi-Fi bridge system with your camera, make sure that the bridges are turned on, wired correctly and communicating before you begin.

.

Let’s Get Started

Now that you have connected your recorder/camera to your internet router and turned it on, you will be able to view it using a program called Surveillance Client.

.

First you will need to download some software called Device Config Tool, which will allow you to find out the IP address of the camera/recorder and edit some of the settings.

.

Download it from here if you are using Windows, and here if you are using a Mac.

.

Once the software has been downloaded and installed, you will see a window like the screenshot below. Make a note of the camera/recorders IP address.

.

.

If the recorder/camera does not appear in the program, first ensure they are turned on and check the connections from the device to your internet router. If you are using a Wi-Fi bridge system, make sure that they are configured correctly (if they were not pre-configured) and are both turned on.

Surveillance Client

If you are using Windows you can download Surveillance Client from here.

.

If you are using a Mac, download it from here.

.

When you have downloaded and installed Surveillance Client you will be presented with a set-up wizard. Click Next, then Add Online Device. Your recorder/camera should appear in the list; select it then click Add Selected Device. 

.

.

Now choose a name for the recorder/camera. By default the username is admin and the password is blank. Now click ‘Add’.

.

.

You will see the device appear in the left hand pane. Select it, click ‘Import’, then open the ‘DefaultGroup’ folder on the right side and you will see it has been added.

.

.

Click ‘Next’ then ‘Finish’ and you will be taken to the main menu. Now click on ‘Main View’.

.

.

When you are taken to Main View, double click on DefaultGroup, then the name of your recorder (if you have one) and the cameras will be shown. In the screenshot I only have one camera connected, which is signified by the green play icon. Double click on the camera name to begin live view. If you want the camera to be in full screen, double click on the live feed.

.

.

To access recordings, go to back to the Control Panel and then click on Remote Playback. Open up DefaultGroup on the left side panel, then select the cameras which you would like to view recordings from and click the play button. You can select the date using the calendar on the bottom right.

.

.

To access the settings of the recorder/camera itself, go to the Control Panel, click on Group Device, then click on the spanner icon next to your recorder.

.

.

For more information on the settings of the recorder, please refer to the quick start guide or the manual.

MORE PAGES >>>

Welcome to our updated comprehensive how-to guide for getting started with your Hikvision IP CCTV system. IP systems are taking over the surveillance world and whether you’re setting up your brand new Hikvision system, or you need help adding more cameras to an existing setup you have, the step-by-step guides in this Megaforum should be all you need to get up and running!

Part 1: How do I install a Hard Drive in a Hikvision NVR?

Any setup with an NVR will need a hard drive to function as it is what all your footage is saved to. The WD Purple Drive is our go-to recommendation for the vast majority of IP setups as it designed with the high workload requirements of 24/7 surveillance solutions in mind. Please see the guide on picking the right HDD to better understand your storage needs and why we don’t recommend using HDD’s that aren’t optimised for use in a CCTV system.

Please see the five simple steps below for getting your hard drive installed into your NVR:
.

.

Step 1:
.

Firstly, you’ll need to locate and remove the screws that secure the NVR’s casing to the base so that you can access the inside of it. Typically, you’ll find two of these screws on the back of the unit and, depending on the NVR model, more on the sides – Do not lose these screws!​

.

.

Step 2:
.

Once inside, your NVR will look something like this. The parts in here you’ll need to identify are the:​

.

.

Now look at your HDD – fewer things to identify here:​

Step 3:
.

Get your hard drive and NVR connected – You can screw the drive into its bay in NVR first if you wish, but it’s normally easier to wire everything up first. Plug one end of the SATA interface cable into the HDD and the other into the corresponding port on the motherboard, then do the same with the SATA power cable. If the power cable has come already connected to the motherboard, then just plug the other end into the HDD’s SATA power port.​

.

.

Step 4:
.

You now just need to screw the HDD into the bottom of the NVR via the screw holes located in the HDD and corresponding holes in the HDD bay (insert the screws from underneath the NVR into the HDD inside – it can be a bit fiddly).​

.

Step 5:
.

Finally, screw the NVR’s casing back onto the base. Your HDD is now installed and ready to be formatted during the initial NVR setup, which is explained in Part 2.​

Part 2: How do I complete the basic setup of my Hikvision NVR?

You now need to configure the NVR so that it’s ready to connect to your network. Don’t worry – this is simpler than it sounds. This initial setup is simplest when done on the local GUI, using a directly connected monitor. The following steps walk you through this initial setup process:

Note – Avoid plugging anything into the back of the NVR until instructed to do so in this tutorial.

Firstly, you’ll need to look at the back of your NVR and make sure you can identify the following parts that are needed for this stage:
.

[1] – PoE (Power over Ethernet) ports (Most Hikvision NVRs have PoE ports which will power any camera via the network cable. Those that do not will require you to connect the camera across remotely, using a separate PoE injector or switch for power.)
​

[2] – VGA display port
​

[3] – HDMI display port
​

[4] – USB port(s) (and mouse – one should come included with the NVR)
​

[5] – LAN port (and ethernet cable – Cat5e or Cat6 is fine)
​

[6] – Kettle power socket (the power lead is included with the NVR)​

Now, follow these steps. It is easier if you leave your cameras disconnected until prompted later in this guide:

Step 1:
.

Plug the kettle plug into the power inlet to connect the NVR to a power supply.​

​

​

.

​

Step 2:
.

Connect your NVR to a display (this can be any monitor or television) by connecting either an HDMI or VGA cable from the monitor to the corresponding port in the back of the NVR.​

​

.

​

Step 3:
.

Plug your USB mouse into one of the NVR’s USB ports.​

​

​

Step 4:
.

Use an ethernet cable to connect your NVR to your local network – Plug one end of the cable into the RJ45 ports into a network access point (such as an ethernet port on your router), and the other into the LAN port in the back of your NVR.​

​

​

.

​

Step 5:
.

Turn the NVR on and let it boot up. Ignore the beeping noise, it’s completely normal and just the NVR telling you that it isn’t properly configured yet.​

​

You may get a prompt to adjust the NVR’s resolution to match the connected display, click “yes” to view everything in the best resolution supported by your display.​

​

​

​

Step 6:

​

Set your language when prompted.​

​

​

​

Step 7:
.

Set a password for the NVR , as well as a “Channel Default Password”, which will be passed onto any inactive device that is directly connected to the NVR’s PoE ports. We recommend keeping these passwords the same for simplicity’s sake. It’s key that you set a password that the NVR defines as strong and that you remember this password, as resetting the passwords on Hikvision devices can be a hassle that you want to avoid, if possible.​

​

Note – If you have lost your password then please see our guide on How to Reset the Password of your Hikvision Camera/NVR in 5 steps using the SADP Tool​

​

​

​

Step 8:
.

Now set a valid “reserved email” address for the NVR, which Hikvision will use for verification if you need to reset your password.​

​

Step 9:
.

Next, set an unlock pattern of your choice by using your mouse to draw any shape you like – you will be asked to do this twice to confirm the pattern. This will be used to quickly login to your NVR in the local GUI.​

​

​

Step 10:
.

Now, set your time zone, your preferred date format, and date/time.​

​

​

Step 11:

​

On the Network Setup page:​

​

Leave the “NIC Type” as it is.​

​

Either leave the “Enable Obtain DNS Server” box ticked, or untick it and use one these recommended public DNS servers.​

​

It is best to leave the “Enable DHCP” box unticked here. Instead, set the “IPv4 Address” of the NVR to an unused IP address on your network, which is within your gateway’s range. Your Gateway will typically be the IP address of your router. E.g. if your router’s IP address is “192.168.1.1”, you’ll want to give the NVR an IP address within the range of “192.168.1.x”, where “x” is any unused address between “2” and “254”.​

​

Note – DHCP can be left on during this stage of the setup to automatically assign your NVR an open IP address if you like, just be sure to turn it off again once your system up and running. To disable it again once set up, just go to: ​

System/Configuration→ Network → TCP/IP → DHCP Off → Apply​

​

Input the Subnet Mask of your network (typically it’s “255.255.255.0”) and “IPv4 Default Gateway”. If you’re unsure of these, see the below articles which explain how to check what they are and if a particular IP address is available:​

How to setup Hikvision IP CCTV System

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

The “Internal NIC IPv4 Address” can be left as it is, this just refers to the NVR’s own LAN address (so Plug and Play cameras will use IP addresses on this range).​

​

​

​

Step 12:
.

You can now stop the annoying bleeping! Select your hard drive(s) from the list and click “Init” to format it, and then “Next” when the formatting has completed.​

​

Note – This will completely wipe the drive, so please make sure that any that are being reused to not have data that you might need on them. ​

​

Step 13:

​

The next page is for the Camera Setup. As mentioned earlier, we recommend connecting any cameras after the NVR setup process has completed, so you can skip this page.​

​

Note – Please see part 4 for the instructions for adding cameras to your NVR after the initial setup. ​

​

Step 14:
.

You will now be taken to the platform access page. Again, skip through and leave this for now.​

.

Note – Please see part 12 for adding the NVR to the Hik-Connect app, which revisits this page. ​

​

​

Step 15:
.

Finally, you’ll be taken to the Change Password page and given the option to set a new admin password. Ignore this, unless you actually want to change your password. Remember, your admin password is different from your activation password, which you’ll need to use when activating individual cameras on your network.​

​

Click “Exit” and “Yes” on the “Exit Wizard” popup.​

​

​

.

That’s the initial setup of your NVR complete. You should now be taken to the NVR’s live view page (you won’t see your cameras until these are connected in Part 4), with your main navigation menu at the top of the screen.​

​

.

Part 3: How do I find my Hikvision device and edit its network settings?

You probably want to be able to view your camera feeds remotely wherever you are; either in a web browser, the iVMS-4200 software, or the Hik-Connect mobile app. All IP CCTV devices communicate over your LAN (local network) and have a unique location on the network. So, you will need to be able to locate where the device you want to view is and make sure it has the right settings for it to work on your LAN. You will then be able to access the device from a PC or mobile device, and connect it with the rest of your CCTV system.

Please follow the steps beneath to find and correctly set your Hikvision device’s network settings.
.

.

Step 1:
.

The first step is to work out if you need Hikvision’s SADP tool or not. If you only need to discover and access an NVR and some Plug and Play cameras connected directly to its PoE ports, then you don’t need to use it.​

​

​

If you aren’t using the SADP tool:​

​

Or, on the NVR’s local GUI (Graphical User Interface – when operating the recorder from a connected monitor and mouse), go to:​

​

System → Network → TCP/IP​

​

Here, you can view and change the NVR’s network settings to match your LAN which is explained in step 2 – you can then ignore the rest of the steps.​

​

​

If you are using SADP:​

​

If your cameras are connected to your LAN, rather than to an NVR’s PoE ports, you will need to install the SADP tool. This scans for all Hikvision devices on your LAN by their MAC addresses. Now, follow steps 2-5 below.​

Step 2:

​

You now need to identify some of your LAN’s settings, which you need to set to match on your devices.​

​

From a Window’s PC, you will need to use the Command Prompt tool to find these.​

​

If you’re using a Mac, then you can find these by launching System Preferences, and then going to:​

​

Network → Advanced (make sure your Wi-Fi/Ethernet connection is selected on the LHS) → TCP/IP​

​

​

Make a note of the following numbers, as you will need to use them when changing your device’s network settings:​

​

IPv4 Address – This is the IP address of the computer that you are using. This address is therefore already occupied, so you will not be able to assign any other devices to this specific address. The digits after the final decimal point indicate where the device is located within the range of your local network, which spans 1-254. You’ll need to change the number after the third period (or full stop/dot) to something that is between “1” and “254” and not already occupied by another device on the LAN.​

​

NB – Please see these guides for instructions on checking if a proposed IP address is occupied:​

​

How-to: How do I find my router and PC’s IP address using a Windows PC?​

How-to: How do I find my router and Mac’s IP address using a Mac?​

​

Subnet Mask – This shouldn’t need to be changed on the NVR, it will usually be “255.255.255.0”.​

​

Default Gateway – This is the IP address that’s been assigned to your router. Any device being added to your system needs to be within the range of your gateway in order to be discoverable.​

.

Step 3:

​

Now, launch the SADP tool again. It should show a list of all the Hikvision devices on your local network and their default network settings. Provided the device is being powered and has a connection to your LAN, then it will show up here. You can also alter the device’s network settings here, and check things like the model number, serial number, the firmware version installed on it.​

​

NB – Remember that any camera that is directly connected to your NVR’s PoE ports will not show up in SADP. This is because the NVR hides any cameras directly connected to it from SADP on its own “subnet”, which is separate from your local network. Don’t worry though, as you won’t need to change the settings for these cameras. ​

.

Step 4:

​

Tick the box beside your device to view and edit the network settings.​

​

If the device hasn’t yet been connected to the network then it will show as “Inactive”. You will be asked to set a password for it when you click the tick-box for it. For more instructions on activating your device, please see Part 6.​

​

​

.

.

​

Once activated, ticking the box beside your device will change the network settings in the “Modify Network Parameters” window, so that they match your LAN. You need to make sure that you enter the password for that device before clicking “Modify” for these changes to be saved.​

​

.

Step 5:
.

Check that these changes have been reflected in the SADP device table – you may need to wait a few minutes before refreshing. If they have, then you should be to carry on with getting this device connected to the rest of your system.​

​

NB – If you aren’t the camera’s first owner then you will need to perform a hard reset on it. This will reset the device to its inactive factory state so that you can set new password by activating the camera in SADP. Once this has been done, SADP will allow you to modify each network setting edit the network settings to match your LAN so that you can use the device standalone or add it to your NVR remotely.

.

Part 4: How do I add a Hikvision device to my NVR?

There are a couple of methods for getting your IP camera connected and recording to your NVR:
.

Plug and Play – This is the most popular and simplest method for smaller setups, as all you need to do is plug your camera straight into the PoE ports in a Hikvision NVR. The NVR will then do the rest of the work. Please note that for Plug and Play to work, the device will need to be inactive or activated with the same password as the NVR.​

​

Remote connection via IP – If you can’t have a wired connection to the NVR, you can instead remotely add a camera on the same network as your NVR to it using the camera’s IP address. For this to work, you will need to make sure to do two things:​

​

1. Replace the power supply that would normally come from the NVR’S PoE ports. Using a PoE switch or injector is usually the best way, as it means you can still add power to the device over the same ethernet cable used for everything else. If not, most will let you connect to a separate PSU.​

​

2. You have connected the camera and NVR to the same LAN and that its network settings are correct for the LAN’s range.​

The following steps will guide you through adding new devices using both of these methods. Part 1 covers doing this on the NVR’s local interface (GUI) and part 2 covers how to do this remotely using a web browser.
.

.

Method 1 – Via the NVR’s GUI:

.

Step 1:​

On the NVR 4.0 menu at the top of the screen, go to:​

​

Camera → Hover over the desired channel → Click on ‘Edit’ (small icon in the bottom-left corner of channel thumbnail)​

​

​

.

Step 2:​

An edit window should appear, fill out the fields to add your camera as follows:​

.

Option 1 – Using “Plug and Play”​

​

Connect the camera to the corresponding PoE port number on the NVR (I.e. D1 corresponds to port 1). Then, just select “Plug-and-Play” from the “Adding Method” dropdown, and then click OK to add the camera to that channel – the camera feed should appear after a few seconds to confirm that it’s been picked up.​

​

Note – If you haven’t activated and set a password on the device in SADP, then the IP address should automatically work. The password will be the Activation Password set on your NVR in the initial setup.​

.

.

Option 2 – Adding manually via IP​

​

Change the “Adding Method” to “Manual”, which will let you alter the other fields.​

​

Now edit the other fields to point your NVR to the camera’s location on the network, like below:​

​

​

Adding Method – Select “Manual”.​

​

IP Camera Address – Enter your camera’s IP address here (as explained in the introduction, this will need to match the range of your LAN).​

​

Protocol – Select the device’s manufacturer if it is on the list, or “ONVIF” if it is an ONVIF conformant product.​

​

Management Port – “8000” by default will work fine, or whatever you’ve set the device’s Server Port to if it’s been changed.​

​

Channel Port – This refers to the channel that you want to add the camera to, so leave this as the corresponding number for the channel that you would like to edit.​

​

Transfer Protocol – Set this to “Auto”.​

​

Username – The username you set up when activating the device, usually “admin”.​

​

Password – The camera’s password, which you will have set when it was first activated.​

​

Use Channel Default Password – If you have assigned the NVR and camera the same password during their activation, then you tick this box. This will use the NVR’s password to add the camera and will save you from entering it again in the future.​

​

Enable IP Camera Time Sync – Tick this, as it means the camera will synchronise with the time set on the NVR.​

​

Use Default Port – You can leave this unticked, as you have specified the management port already.​

​

Verify Certificate – Leave this box unticked too.​

​

​

Click OK to save your changes, the NVR should pick the camera up after a few seconds and show the feed on that channel’s thumbnail to confirm this.​

.

.

Step 3:​

To rename the camera, go to:​

​

Camera → Display​

.

Then, select the camera’s channel from the dropdown, and use the field below to set a new name.​

​

Click “Apply” to save your changes.​

​

​

​

​

Step 4:​

You may want to rearrange the Live View screen to show the new camera on a particular tile. To do this, first, go to:​

​

System → Live View → View​

​

Then, select the output port for your connected display that you would like to show the camera on, click on the selected tile and then double-click on the new camera to add it to that tile.​

​

You can select different layout options, or create a customised layout using the toolbar at the bottom of the page.​

​

Click “Apply” to save the new layout.​

​

​

To check the new layout, launch “Live View” using the NVR’s main menu, and then select that layout using the toolbar in the bottom right-hand corner.​

​

​

.

Method 2 – In a web browser:

.

Step 1: ​

Browse for NVR’s IP address in a web browser, and log in with your username and password for it.​

​

.

Step 2:​

Now, navigate to:​

​

Configuration → System → Camera Management → IP Camera​

​

You’ll be shown a table of all the NVR’s channels, showing which are occupied by cameras, and which aren’t.​

​

These channels normally correspond to the same-numbered PoE ports on the back of the NVR.​

​

Click on the channel that you want to add your device to, and then the “modify” button above the table.​

​

.

Step 3:​

A window titled “IP Camera” should appear allowing you to change the “Adding Method” and “IP Camera Address” set for that channel.

If you haven’t already, you will need to make sure that the camera has a valid IP address and correct network settings for your LAN’s range.
.

Option 1 – using “Plug and Play”:
.

You just need to make sure that:​

​

Note – If you haven’t activated and set a password on the device in SADP prior to connecting it to the NVR, then the IP address should automatically work and the password will be the “Channel Default Password” set on your NVR in the initial setup (see step 7 here)​

.

Option 2 – Adding manually via IP:​

​

Change the Adding Method to Manual, which should let you alter the other fields.​

​

Now alter the other fields to point your NVR to the camera’s location on the LAN, like below:​

​

​

IP Camera Address – Insert the camera’s IP address​

​

Protocol – Select the brand of your camera here, or ONVIF if it is ONVIF conformant and the manufacturer doesn’t appear in this list.​

​

Management Port – This is the camera’s network port, which is usually 8000 by default.​

​

Username – The username that you set for the camera, which is usually “admin”.​

​

Password – The password assigned to the camera upon activation in SADP. If you have automatically activated the camera by plugging it into your NVR’s PoE ports, this will the the “Channel Default Password” set during the NVR setup.​

.

Confirm: Retype this password.​

​

Transfer Protocol: This is fine for you to leave as “Auto”.​

​

.

Green ticks should appear beside each field to indicate that what’s inside is valid. Once completed, you can click “OK”:​

.

​

The “Security” column should be “Strong” and “Status” should change to “Online” on the “IP Camera” page – If they do, then you’re finished, just return to the Live View page to check that the camera’s feed is now visible.

​

Note – Clicking the “Start All Live View” button in the toolbar at the bottom of this page will show all of your working cameras feeds at the same time.​

​

Click on other pages for more.

ALIBI Vigilant NVR User Manual, This manual describes how to use your NVR locally and on the Web interface.
In this manual, the terms “IP camera” and “IPC” both refer to “network camera”, which requires a connection to the network. The IP device mentioned in this manual refers to either an IP camera (also known as network camera) or a Digital Video Server

Preface

This manual describes how to use your NVR locally and on the Web interface.

In this manual, the terms “IP camera” and “IPC” both refer to “network camera”, which requires a connection to the network. The IP device mentioned in this manual refers to either an IP camera (also known as network camera) or a Digital Video Server (DVS).

9

.

Part I Local Operations

An NVR supports two types of operations: local operations and web-based remote operations. With local operations you connect a monitor and a mouse to the NVR and use the mouse to operate the system. If your NVR has buttons on the front panel or is delivered with a remote control, you may also control your NVR by pressing the front panel buttons or using the remote control.

The NVR has an embedded web server that allows web-based operations. To do this, you need a PC that has a network connection to the NVR and is installed with a web browser. You just need to navigate to the NVR’s IP address and log in to the Web interface like you log in to the system locally.

This section describes local operations.

10

.

1 before you begin

Please be aware that the parameters that are grayed out on the system user interface (UI) cannot be modified. The parameters and values displayed may vary with device. Figures in this manual are for illustration purposes only.

User Login

Use the default username admin and password 123456 for your first login.

j^ CAUTION!

The default password is intended only for the first login only. It should be immediately changed to a strong password. Strong Passwords contain at least nine characters that include letters, numbers and special characters.

Local Operations

You can refer to Initial Configuration and complete a quick configuration.

NOTE!

Unless otherwise specified, all operations described in this manual are performed with a mouse by the right hand. See Mouse Operations for details.

11

.

Mouse Operations

Table 1–1 Mouse Operations

Front Panel Buttons

The front panel buttons may vary with NVR model.

Table 1–2 Front Panel Buttons 1

12

.

Table 1–3 Front Panel Buttons 2

13

.

14

.

Remote Control

Table 1–4 Functions of the Buttons on the Remote Control

15

.

ALIBI Vigilant NVR

.

2 initial configuration

Preparation

Device Login

The login page appears after the NVR starts up.

17

.

Login

Please change the default password. Change now?

No

Change Password

Username  admin

Old Password

Password  Weak

Confirm

OK  Cancel

18

.

Note:

To disable unlock pattern, click System > User. See User
Configuration for details.

Wizard

The wizard can guide you to complete the most basic setup. The following page appears after your login:

19

.

Note:

20

.

3 live view

Live View Status

The following icons are used to indicate alarms, recording status, and audio status in a live view window.

Table 3–1 Live View Window Icons

Window Toolbar

21

.

Screen Toolbar

22

.

Shortcut Menu

A shortcut menu as shown below appears when you right-click in a window. Some menu items are described in Shortcut Menu Description.

Table 3–2 Shortcut Menu

Table 3–3 Shortcut Menu Description

23

.

Sequence Operation

The sequence operation requires you to configure the screen layout, windows, linked cameras, and the sequence interval.

This example describes how to configure sequence for five cameras based on a 4-window screen layout.

NOTE!

The number of windows that can be displayed may vary with NVR
model.

24

.

NOTE!

Zoom

Zoom in on an area of images in a window for details.

Preview Configuration

Normally, live view (video) is available after you complete the basic setup by following the wizard. You can click System > Preview and edit preview setting as needed, including video output, image resolution, default layout, and sequence interval. The video output and the number of windows supported may vary with NVR model.

NOTE!

Pressing and holding the scroll wheel for at least 3 seconds will
restore the default resolution.

Preview Configuration

Each preview window (window for short) links to a camera. By default, window 1 links to camera D1, window 2 links to camera D2, and so on. You may want to change the link to display live video from a camera in another specified window. The following example describes how to link window 1 to camera D2 and link window 2 to camera D1.

26

.

Step 1: Click window 1 on the right, and then click D2 under Camera on the left. Now D2 appears in window 1, and None appears in window 2. Meanwhile, o is cleared for camera D1, meaning D1 is not linked to any window.

Step 2: Click window 2 on the right, and then click D1 under

Camera on the left. Now D1 appears in window 2. Click Apply to

save the settings.

Advanced Configuration

Click the Advanced tab and then select Sub Stream First so the NVR uses the sub stream to establish live video from multiple cameras simultaneously. This function is disabled by default.

ALIBI Vigilant NVR User Manual

Read Next : Alibi Recorder Firmware

.

4 channel configuration

Channel Management

This chapter describes how to add and manage IP devices in your NVR. The IP devices mentioned in this manual mainly refer to IP camera (or network camera); sometimes they can also be Digital Video Server (DVS). Before you start, make sure the IP devices are connected to your NVR via network.

CAUTION!

An IP device should be connected to one NVR only. An IP device managed by multiple NVRs may cause unwanted issues.

Adding an IP Device

This section provides multiple options to add an IP device. Some options are only applicable to certain NVR models. Choose one as appropriate.

Option 1

28

.

NOTE!

For a Digital Video Server (DVS), a window appears when you click
Add, and you need to select channels to add the connected
cameras.

Option 2

This option is not applicable to NVRs with PoE ports or switching ports.

Option 3

This option is only applicable to NVRs with PoE ports or switching ports. Connect an IP camera to a PoE port or a switching port with a network cable. The connected camera will be added to the NVR

automatically. Check status under Camera > Camera > Camera.

0 means live video from the camera is available. Click © to view

live video.

If the camera is connected via a network switch, click ışı under

Cam Config in the window displayed, set Add Mode to Manual

and then complete the settings correctly.

NOTE!

» appears under Status if the power output from a PoE port is
below or above the rated power of the connected camera.

Option 4

Use this option to add an IP device that is connected to a different router, for example, when the NVR and the IP device are connected across the Internet.

29

.

NOTE!

First you need to enable port mapping at Setup > Port > Port
Mapping on the IP device’s Web interface.

• By MyDDNS

a. On the IP device’s Web interface, go to Setup > Network > DDNS, enable DDNS, select MyDDNS, set a domain name and get the server address.

NOTE!

• By a domain name

30

.

NOTE!

Option 5

Use this option only when the IP device to add supports the standard RTSP, and all you need from the IP device are just view live and playback. IP devices added in this way cannot be configured from the NVR.

Sort Cameras

Sort cameras to display in the desired order.

32

.

NOTE!

33

.

NOTE!