FLIR PC-NVR turns the computer into an NVR and will use your hard disk drive (HDD) on your PC to store recorded video.

IMPORTANT: If you install PC-NVR and want to remove it afterwards, you must uninstall FLIR Cloud Client software entirely and re-install it with the PC-NVR option not selected. Uninstalling FLIR Cloud Client will require the administrator password. If you do not have this password, you must contact technical support for assistance in recovering your password.

The following instructions require you to access your system using the FLIR Cloud Client software and a PC.

REMINDER: FLIR PC-NVR can be installed while installing FLIR Cloud Client. However, if it is not initially installed, FLIR Cloud will need to be uninstalled and re-installed to install FLIR PC-NVR at a later date.

Prerequisites:

To add a channel from the DVR / NVR in FLIR PC-NVR:

1.Launch FLIR Cloud Client software on your computer, then click PC-NVR.

2.Click the Plus icon () to open the Add Channel window.

3.Enter the device ID or IP address of the system you want to add.

4.Select the channel you want to add using the checkbox, then click Import.

Once you have added the channel, you can configure your hard disk drive (HDD) settings for your PC.

To configure your HDD settings:

FLIR Cloud PC-NVR installation and setup

You can set a recording schedule for each connected camera in FLIR PC-NVR.

To set a recording schedule for a camera:

Your PC-NVR will behave as a virtual NVR system and save your recorded video to your PC. FLIR PC-NVR shows in the Device list and behaves like any other DVR / NVR system in the FLIR Cloud Client software.

.

Your LHV / LNR Series DVR / NVR system can be manually added to the FLIR Cloud Client software by entering the system IP address.

Prerequisites:

To manually add the LHV / LNR Series DVR / NVR using an IP address:

1.Launch FLIR Cloud Client software on your computer to open the Login window.

2.Enter your login information. Refer to your user manual for your default Username and Password.

3.Click Login to open the Home window.

4.Click the Devices icon () to open the Devices tab.

5.Click Manual Add on the bottom-left corner to open the Manual Add window.

6.In the Manual Add window, enter the following information:

◦ Device Name: Enter the Device Name of your choice to identify the DVR / NVR.

◦ IP/Domain Name: Ensure the IP/Domain checkbox is checked to enable connection using the IP address. Enter the IP address of the DVR / NVR.

◦ Client Port: Enter the Client Port value (default: 35000).

◦ User Name: Enter the DVR / NVR User Name.

◦ Password: Enter the DVR / NVR Password.

7.Click Add to connect the DVR / NVR. The connection may take a few minutes.

.

Your DVR / NVR can be manually added to the FLIR Cloud Client software by entering the device ID. FLIR Cloud Client software is available for download on PC / Mac. Click here for more information on locating software downloads.

Prerequisite:

To manually add the DVR / NVR using a device ID:

1.Launch FLIR Cloud Client software on your computer.

2.Enter your login information. Refer to your user manual for your default Username and Password if needed.

3.Click Login to open the Home window.

4.Click the Devices icon () to open the Devices tab.

5.Click Manual Add on the bottom-left corner to open the Manual Add window.

6.In the Manual Add window, enter the following:

◦ Device Name: Enter the Device Name of your choice to identify the DVR / NVR.

◦ Device ID: Enter the device ID or scan the QR code located on the top of the DVR / NVR.

◦ Client Port: Enter the Client Port value (default: 35000).

◦ User Name: Enter the DVR / NVR User Name. Refer to your user manual for your default Username if needed.

◦ Password: Enter the DVR / NVR Password. Refer to your user manual for your default Password if needed.

7.Click Add to connect your DVR / NVR. The connection may take a few minutes.

8.Click Home, and then double-click Default Group to load your connected cameras.

If you are not able to connect to your DVR / NVR using the device ID on the same network, you may be experiencing a NAT Loopback issue. Routers recognize and connect to DVR / NVR via IP address. To connect your system from the same network, use the IP address of the DVR / NVR. Click here for details on using the IP address to manually connect your DVR / NVR.

Hikvision NVR 5.0 Professional Installation Guide

Hardware Installation

Software Configuration

Additional Resources

Important Note: The provided steps serve as a general guideline. Specific configurations might differ based on your NVR model. Always refer to the official user manual for detailed instructions and advanced functionalities.

Setting up a Hikvision NVR (Network Video Recorder) involves several steps, including hardware setup, network configuration, and camera configuration. Here’s a detailed guide to help you set up your Hikvision NVR 5.0:

1. Hardware Setup

Step 1: Unbox and Connect Components

Step 2: Connect the NVR to a Monitor

Step 3: Connect the NVR to the Network

Step 4: Connect Cameras to the NVR

Step 5: Power Up the NVR

2. Initial Configuration

Step 1: Boot Up and Log In

Step 2: Set Date and Time

Step 3: Network Settings

3. Adding Cameras

Step 1: Detect and Add Cameras

Step 2: Configure Camera Settings

4. Recording Settings

Step 1: Set Up Recording Schedule

Step 2: Configure Storage Settings

5. Remote Access Setup

Step 1: Enable Hik-Connect

Step 2: Port Forwarding (if necessary)

Step 3: Mobile App Setup

6. Final Steps

Step 1: Test the System

Step 2: Backup Settings

Troubleshooting Tips

This guide should help you set up your Hikvision NVR 5.0 system. For more detailed instructions, refer to the user manual or the Hikvision support website.

.

InVid Tech is here to help you succeed, and as a company, we pride ourselves on the level of personal service we offer. We have an experienced team based in the United States, including Sales, Customers Service, Marketing & Tech Support. Additionally, there is support for Latin American Countries.

How do I access the cameras on my computer?

Go Here, login using with the credentials you used to sign up with. You will see your devices at the top, click ACCESS and it will launch a new tab for that device. This info can also be found by going to our website and downloading it Here 

How do I network the unit so it can be viewed remotely?

First you want to make sure you plug the unit into your router. Now on the unit login, then right click on the mouse and go to Menu> System> Network. You can set the IP Address under “TCP/IP”. Once you’ve entered your IT information go to “P2P” across the top. Make sure it is enabled. Below you will see the server address Here. You will go there and create an account then link the unit with your account. See Link below for more detailed instructions. Here

How do I connect a third party camera?

You will need a PC and the manufacturers IP tool to address the camera(s) IP address within the same scheme as the internal NIC of the NVR (172.16.0.x). Now go to the camera management within the NVR, switch the port that the camera(s) are plugged into from PNP to IP address, protocol will be ONVIF, port will be 80 (HTTP port of the camera) and type in the username and password of the camera and it should connect. Some manufacturers require ONVIF to be enabled within the camera before adding to different unit. Please check their website for information on how to enable ONVIF.

Why can’t I use Chrome, Firefox, Edge or Safari to view my device(s)?

Chrome, Firefox, Edge and Safari took away a plugin that was used for ActiveX plugins. This has effected anyone that uses an ActiveX plugin for their devices not just InVid.

Why is my Vision camera not connecting to the NVR?

That may be due to the NVR having the old default password of 123456. Leave the camera plugged into the unit and go to Menu>Camera then click on the “cog” (gear looking icon) next to the port of the camera you are trying to connect. Type in the password “1234567u” for the camera and the camera should then connect.

Why did my device suddenly go offline?

If you are connected to your ISP’s router (Internet Service Provider) occasionally it is possible your ISP is doing a update which can occasionally change your network environment and require a reboot of your router/recorder (Router first then recorder). It is highly recommended that with this device to install your own router to run the recorder to avoid this from happening, however if using your ISP’s router the above stated solution is the fix for it.

How do I Share a device added to my star4live account?

Have the new user create an account Here. Log into the account with your device, click on SHARE, enter in the customers user name or email, choose a “valid to date”, when this date hits the device will no longer be shared, and hit ok. The device will now be found under the Shared Record. This info can also be found by going to our website and downloading it Here

Trying to view devices on IE but can’t download the plugins?

Please ensure you are in fact using Internet Explorer and not Edge. The two have similar icons, Edge is a darker blue lower case “e” whereas Internet Explorer is a lighter blue lower case “e” with a yellow ring going over the top left of the “e”. Also note that on Windows 10 Edge is the default browser, Internet Explorer isn’t on the task bar or the desktop, you can use Cortana and search “Internet Explorer” to launch.

How do I turn On/Off motion function?

Right click on the mouse, go to the menu>alarm>motion. By default motion detection should be enabled. You want to draw the area of where you want motion to be detected and then hit apply down at the bottom.

How can I see video from last week?

To playback video you want to right click on the mouse and the second to last option on the bottom is “Playback”. On your right you will select which cameras you will like to playback, below the camera list select the date in which the video was recorded. Hit the play button down at the bottom and the playback should start.

How do I add a User?

Right click on mouse go to Menu>System>User. Click Add at the bottom. Create the username and password then select permissions you want to grant that user and hit OK.

How do I format my hard drive? Vision Series

Go to Menu, click on Storage, click on Hard Disk, select your disk(s) and click Format (remember, this erases all data on that drive(s)).

Do I need to port forward this device? Vision

If you’re using the P2P which is explained above no port forwarding is required, if you are networking this device to be seen remotely via a WAN IP or DDNS, yes port forwarding is required.

Is there a manual for this device?

Yes, you can find it on our website Here

Where can I check to see if my unit is recording?

The best way is by doing a playback (refer to question above). You can also go into the Menu, select Maintain on your left and Recording across the top.

InVidTech Vision Series Setup Guide v1

How to Setup Vision Email Notification

Learn how to setup email notification on your Vision machine

Step 1: Setting up a GMAIL account.

1. Go to My Account setting page, click on the square and click my account.

2. Click Signing in to Google.

3. Click Allow all less secure apps on

Step 2 – Setting DVR/NVR Configurations

Enabling Motion Detection

Hit Apply to save then OK

What is the default password of the Vision devices?

We provide a sticker on the inside of the boxes, whether it’s a DVR Encoder, NVR or IP Camera. The default user name and password could be either “admin/123456” or “admin/1234567u”. Once the change-over is fully complete they will all be “admin/1234567u”

How to Setup Vision P2P Using the QR Code

With P2P QR connection there is no need to set any ports, worry whether or not your uPnP is enabled within your router, do any port forwarding within your router or setup a DDNS name.

Not connected? Here are some things to check

Viewing your Vision Device Online or from Mobile App

Viewing from your Web Browser (Internet Explorer):

Viewing from your InVid Vision mobile app:

Is my unit up to date with its firmware?

To find out if the unit is up to date Locally, you want to go to the Menu, select Maintain on your left then Upgrade. Now select “Upgrade by Cloud” (across the top) then hit “Check” in bottom right had corner. To find out if the unit is up to date Remotely, you want to go to Setup, then Maintenance then Maintenance again and hit “Check New Version”. If it is the latest firmware it will say “The current version is already the latest.” If it is not up to date then you will be prompted to upgrade, which will download the file from the cloud, upgrade and restart your NVR.

How do you check to see if an upgrade is available for the Vision NVR?

Is it possible to reset a password for a device?

Yes please contact our Tech Support, 631-388-5700.We will need the devices FULL serial number, you can do this at the main monitor or from the web interface.

How do I access the cameras on my phone?

Once you have downloaded the VISION app from the App Store or Google Play store, sign in with your login credentials used when creating your star4live account.Hit the camera icon in the top right hand corner and you will see a list of all devices added to your account.Choose the device youd like to access and hit “Start Live View” at the bottom of the screen. This info can also be found by going to our website and downloading it Here

Where do I download the APP?

-The app can be found at either the app store for an Apple device, or the Google Play store for an Android Device, you want to search “Paramont CMS”. This info can also be found by going to our website and downloading it Here 

What App do I use for my phone?

InVid Vision

How do I view my device(s) on my Mac?

The current work-around is to install the appropriate CMS software which will allow you to watch live and playback your device(s). You can download the CMS software(s) off our website Here. 

.

Safety cautions

Product overview

DVR

Camera

Power Cable Splitter

BNC Cable

Xmeye Dvr System Instructıons For Use

Read Also : Camius devices troubleshooting

Hard Drive Installation

IMPORTANTTo record videos and play the historical videos, the installation of the Hard Disk Drive is a must.
Otherwise,you can only watch the live video.
This DVR system works with a 3.5” SATA Hard Drive.The Hard Drive should be formatted after it’s installed.×Dismiss this alert.

System Connections

IMPORTANTDo not fix the AHD camera before you can view the image on the monitor and confirm the ideal position to install it.×Dismiss this alert.

1.Plug a power adapter into the DVR and the socket to power on the DVR.

2. Connect a monitor to the HD Output or VGA Output on the DVR with an HDMI cable or VGA cable (not included).

3. Connect the Ethernet Cable with the DVR and your router.

4. Connect the AHD camera with the BNC Cable.

5. Connect the Yellow Video Connector to the BNC Video Input on the DVR, and connect the Red Power Connector to the Male Connector of the Power Cable Splitter.

6. Connect the Female Connector of the Power Cable Splitter with another power adapter. Then plug the power adapter into the socket to power on the camera.

Operate dvr system with a monitor

Startup Wizard

After connecting the DVR and cameras to power, wait for 2-3 minutes. A Startup Wizard will start to guide you via a series of pop-up windows.

Connect the USB mouse to the DVR, then click Next until you see the window of Time-Language Configuration.

1.Select the time zone, date format, time format, language, and set the time for your DVR system.

2. The default password is empty, please reset it for your DVR following the tip.
The new password should be more than 6 digits and use the combination of numbers and letters to ensure your system’s security.

3. Select safety questions and enter the answers for resetting the password if necessary.
You can also enter your email address for getting the verification code to reset the password.

4. Check if the network connection status is normal. If not, you can configure it by clicking Network.

5. Scan the QR code to get the Serial Number of your DVR system and download the App named XMEye into your mobile device.

6. Before fixing the cameras, you can log in to XMEye App to check the live view to confirm the ideal position.

7. Detection based on human shape is enabled by default.
The DVR system will send alerts to your mobile device when there is human shape detected by the cameras.
Please refer to the section of Motion Detect the detailed setting.

IMPORTANTClick Next and OK to exit the wizard. You can right click on the screen, then go to Main Menu > Startup Wizard to bring it up again.
If the wizard is no longer needed, just check the box before Don’t Display the Wizard again on the first interface of the Startup Wizard.×Dismiss this alert.

Live Video

You will see the live videos from the AHD cameras in split-screen mode (9 screens by default) after exiting the wizard.

※ Move the mouse cursor to the live video of any channel, some icons may be displayed according to the setting.

Notes:

1.The icons of and are displayed by default, while for icon , and , please right click andgo to Main Menu > Alarm (see on page 15) to enable them.

2. If you want to loop to display the live videos from some certain channels in full-screen mode, please go to Main Menu > System > Tour to enable this function.

3. For viewing the live video from one channel in full-screen mode, please move the mouse cursor to the desired channel, then double click. To exit full-screen mode, double click again.

Hard Drive Formatting

When you receive the system, the system has a pre installed hard disk, which does not need to be formatted,but if you have to replace another hard disk, it needs to be formatted at first ,then it can be used normally Install the Hard Drive first, then right click and go to Main Menu >Advanced > Storage to check if the type is Read/Write or the status is Normal.

If not, please click Format Storage to start formatting your Hard Disk Drive.

Video Recording

Right click on the screen, then go to Main Menu > Record > Record Conf. to set the record mode and record plan.
This DVR is set to record videos 24 hours a day by default.

Channel:

Select the channel to set the record mode and plan. You can select a single channel or all channels.

Redundancy:

Installing 2 pieces of Hard Disk Drive is required when enabling this function, and HM245 doesn’t support it.

Length:

Set the maximum video length of each recording from 1 minute to 120 minutes. It’s 60 minutes by default.

PreRec:

The camera will start recording a video around 5s before it detects the motion or human shape.

You can reset the time from 1s to 30s, but the accuracy of the pre-recording time may be affected by the bitrate.

Mode:

Set the recording mode and the options are Schedule, Manual and Stop.

Record Plan:

Set the recording schedules.

Notes:

The oldest video will be overwritten by the latest one by default when the Hard Disk Drive runs out

of space.

Video Playback

Right click on the screen, then go to Main Menu > Record > Playback to play the video recorded.

You will see the different playback modes in the pop-up window of Play Mode.

Explanation of playback modes

1.Common Playback

Select the channel(up to 4 channels at the same time), a period and a date on Blue background to

play all types of videos recorded.

1. Area for Video Playing
2. Playback Buttons
3. Timeline
4. Channel
5. Filters
6. Filtered Videos List
7. R: Standard Videos
8. M: Videos recorded when the camera detects motion or human shape.
9. Detailed Info. of the Selected Video
10. Search
11. Show/Hide Filtered Videos List
12.Timeline by Hour/Minute

TipFilters will not be available after you left click on the timeline, but you can exit this mode and re-enter to select the filter.×Dismiss this alert.

Option 1 :

Left click on the Green/Red (Green for standard videos recorded, and Red for the videos recorded whenthe camera detected motion or human shape) part of the timeline of each channel to play the historical videos.

Option 2 :

Left click on the live video of one channel, show the filtered video list, then double click on the selected video to play it.

Description of Playback Buttons

Left click on the live video of any channel, then start using the buttons to control the video playback.

Tips:

① You can click the icon to cut a video, then click to back up to the external storage.

② Previous Frame and Next Frame work only when pausing the video.

③ The speed of Fast Reverse and Fast Forward will be displayed on the right end of Playback Buttons.

2. Sync Playback

This function aims to put the videos from different channels at the same time to compare.

Select 2 channels at least ( up to 4 channels), a period and a date on Blue background to play the historical videos simultaneously at the selected time on the same timeline.

3. Dayparting

This function aims to put the videos from the same channel but at different time to compare.

Select a channel, number of split screens, and a period to play the videos recorded from this channel on different timelines.

NotesYou need to press and hold the left mouse and move on the bar of Period to select time period.×Dismiss this alert.

4. Smart Express

Select one channel or all channels, then select the speed of Fast Playback, the system will play all the videos recorded with the speed you selected.

5. Smart Search

Select one channel and a time period, then check the box before Detect and select a date on Blue background to play the videos recorded when the camera detected the motion or human shape.

※Double click the thumbnail to play the related videos.

6. Face Search

Select one channel, a time period and a date on Blue background to play the videos recorded when the camera detected faces.

Video Backup

Step 1:

Insert the USB disk into the USB port of the DVR system. Right click on the screen, then go to Main Menu >Record > Backup to start.

Step 2:

Select your USB disk, then click Backup to bring up a pop-up window.

Step 3:

Select Channel, Start Time and End Time, then click Add to display all the filtered videos.

Step 4:

Check the box to select the video files and Backup format, then click Start to back up the videos.

Tips:

① The format of the USB Drive should be FAT 32.

② An alternative solution to back up the videos is listed below.

• Go to the interface of video playback and click to show the filtered video list.

• Check the box to select the videos.

• Click to start backing up. The next steps are the same as the first solution mentioned above.

Snapshot Setup

The system will capture the snapshots 24 hours a day when the camera detects motion or human shape.

Go to Main Menu > system> SnapShot Conf. to reset the time interval of capturing a snapshot, and set up the schedules when the camera will capture a snapshot as well.

Alarm

IMPORTANT:

The alarms of Motion Detect and Human Detect are enabled by default. If you need to record videos whenthe camera detects the face or gets blocked as well, please enable Face Detection and Video Blind.

Please go to Main Menu > Alarm to set the alarm you need.

Motion Detect

The camera will start to record videos when it detects motion.

Channel:

Select the channel you’d like to enable motion detection.

Enable:

Check the box to enable motion detection.

Sensitivity:

If you select higher sensitivity, the camera will be more easily to be triggered to start recording videos. It’s advised to select Middle to balance the accuracy and effectiveness of the alarm, thus reducing the false alarms.

Region:

Click Set, then press and hold the left mouse to drag and select the area for detecting. The pink area indicates the selected area.

Period:

Set up to 4 time periods for each day to send the alerts when the camera detects motion.

MD Interval:

Set the time interval of two alerts. It aims to decrease the frequency of the alerts caused by the same moving object.

Record Channel:

The selected channel(s) will start recording when the current channel detects motion.

Tour:

The display will loop to display the live video from the selected channel(s) in full-screen mode when the current channel detects motion. You can go to Main Menu > System > Tour to set the time interval to show the live video in full-screen mode.

Snapshot:

The selected channel(s) will capture a picture when the current channel detects motion.

PTZ Activation:

The cameras don’t support this function.

PostRec:

The camera will remain to record the video around 10s after the motion or human shape detection ends. You can reset the time from 10s to 300s.

Show Message:

After enabling this function, the display will pop up a window to show the Alarm Status for all kinds of alarms when the cameras detect motion, human shape, or more.

Send Email:

Before enabling this function, please go to Main Menu > System > NetService, then double click on EMAIL option to set up your email address to receive the alerts.

Write Log:

The logs of the alerts will be written into the system once you enable this function. You can go to Main Menu > Info > Log to check the detailed log information.

FTP upload:

The system will send the videos recorded or snapshots captured to the FTP server you set when the camera detects motion. Please go to Main Menu > System > NetService, then double click on FTP option to set up your FTP server.

Mobile reported:

The system will send alerts to your mobile device when the camera detects motion. Please install the App and add the DVR to the App following the section of OPERATE DVR SYSTEM ON MOBILE DEVICE on page 18.

Up-to-Coaxial Control

Right click on the main menu and select XVI control to start setting up your camera.

※If the live video from the camera is mirrored or flipped, you can check the box before Mirroring or Overturn to fix it.

※If you set something wrong, please click Restore to get back to default settings.

.

NotesFor the setting of alarms like Video Blind, Video Loss, Human Detect and Face detection, please refer to the settings of Motion Detect. If prompting Video Loss, the DVR will not record videos, but only to send alarms.

TROUBLESHOOTING

The DVR System Boots Up Abnormally Or Reboots Automatically.

If the issue persists, please contact Support for more help.

.

How Should I Do If I Forget My Password?

• Please click Forgot Password when logging into the DVR system.

• The system will ask you the security questions you set in the Startup Wizard, please enter the right answer to reset your password.

• If you forget the answers, click Forget Answers to enter the interface of Verification Code.

• Launch XMEye App,tap > FIND PWD on an Android device or tap Forgot your device password?(on the interface of Add Device) > FIND PWD on an iOS device to scan the QR code on the left side to get a verification code, then enter it into the box on the interface of Verification Code to reset your password. However, if you set an email to get the verification code in Startup Wizard, the App will send the code to that email. You need to get it from email, then enter it on the interface of Verification Code.

.

How Long Can A Hard Disk Drive Record For This DVR System?

There are 4 AHD cameras connecting to this DVR system by default. These cameras are with the resolution of 1080P and variable bitrate which depends on the surveillance scenes. If the bitrate is around 2Mb/s, the corresponding size of the video file will be around 21G per day.

As a result, a Hard Disk Drive with the capacity of 1T may record around 12 days.

.

How Can I Connect An Extra Camera With The DVR System In Addition To The 4 Cameras In The Package?

DVR system supports up to 8 cameras to be connected. Please contact Hiseeu to get the same type of cameras and the corresponding cables.

If you just have a camera in hand, please follow the steps below:

For the camera with the format of TVI/CVI/SVI/CVBS, right click on the screen, select XVI&AHD to set the Signal of the channel to Auto or the corresponding format of your camera, then connect the camera with the DVR system.

For an IP camera, please go to Main Menu > System > Digital > ChannelType to check the box of the fourth line, then go back to the main screen and move the cursor to the channel you’d like

to connect the camera.

Click in the center of the screen to start adding the camera.

.

The Image From The Camera Is Upside Down.

Right click on the main screen and click XVI Control, then check the box before Mirroring or Overturn to flip the image.

.

What Should I Do If It Runs Out Of The Space On Your Hard Disk Drive?

The DVR system is set to loop recording by default, which means the latest videos will overwrite the old videos automatically when it runs out of the space on the Hard Disk Drive.
You can back up the important videos, then delete the videos or format the Hard Disk Drive.

.

Why Does The Hard Disk Drive Stop Saving Videos?

.

The App On My Mobile Device Cannot Receive Snapshots When The Camera Detects Motion, Human Or The Camera Gets Blocked, Etc.?

The App can receive the snapshots by default and you can check from Alarm Push/Alarm of the App.

.

Why Does The App Remind Me Of “Maximum Video Link”?

For remote viewing, such as from App or PC Client, you can only simultaneously access the live videos from 6 channels at most. Please close the unnecessary channel.

.

Why Doesn’t The PC Client Watch The Live Videos?

.

Why Doesn’t The PC Client Watch The Live Videos?

.

What Should I Do If I Got Too Many Push Notifications From App?

This DVR system can support to send you alerts when the camera detects motion, human, face, video feed loss,or the camera gets blocked. You can go to Main Menu > Alarm to disable certain kinds of alarms to reduce alerts.What’s more, you can lower the Sensitivity, set the Region and Period to reduce alerts.

.

How Can I Modify The Time Stamp And Channel Name Displayed On The Screen When Playing The Videos Recorded?

You can go to Main Menu > System > Display to select the channel you’d like to set, then enable Time Display and Channel Title, then click Set. You can even drag them to your desired position on the screen.

.

Is the fan noise on my DVR NVR recorder normal?

Q- Is the fan noise on my recorder normal?

A- Digital or network Vide Recorder’s fan is comparable to one in a mini PC, and the sound coming out of the vent that you may hear is a sign of a DVR that’s working well.

The working fan indicates that the trapped heat is being dissipated, and the DVR can record 24/7 on the hard drive, and without this cooling mechanism, the DVR and hard drive’s life span will be shortened.

How to add IP Camera to Camius DVR (Advanced Security XVR)

Camius Trivault DVR recorders are designed to support analog security cameras via coaxial wiring and IP cameras over the Network. To add an IP camera to Camius DVR, you’d need to add PoE cameras to your local Network. Then, connect a regular network or PoE switch to the LAN port of the Camius DVR. Based on the example of a Camius 16-channel DVR, the connecting diagram illustrates this process. This system allows users to quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection.

If you are not using a PoE (power-over-ethernet) switch or a PoE injector, you can power the IP camera by connecting a UL-listed 12VDC-2AMP power supply to the DC plug on the camera and an ethernet cable between the IP camera and the router or switch on your local network.

Camius TRIVAULT4K2168R Connection Diagram

Camius TRIVAULT4K184R, TRIVAULT4K184R2 Connection Diagram

Navigate to the DVR’s Menu >> System >> General >> Mode >> Set to XVR and Apply.

Wait 1 to 2 minutes for the surveillance DVR to reboot in a hybrid XVR mode. This switch will reset the Configuration and Password.

There are a few ways to add IP cameras to the DVR, and we will describe them below.

Adding IP Cameras in the Start Wizard

While in the Start Wizard, navigate to the Network>> Date/Time >> IP Cameras.

Click the Search button to add compatible IP cameras on your local Network. Next, select the IP camera(s) you want to add, and then click the arrow icon to add them to the DVR, followed by the Next button.

Select the suitable Protocol from the dropdown (Private is for Camius IP cameras), enter the IP camera(s) credentials (User Name and Password), and click Add. Green status indicates a successful connection; grey status could show a password or network error.

Adding an IP camera while in the DVR’s Setup Menu

If you add IP cameras to DVR’s menu, navigate to Channel >> IP Channels.

Select the IP camera you wish to add, click the ‘Add‘ tab or use a plus button.

The ‘Add IP camera‘ window will pop up with IP camera details.

How to add IP Camera to Camius DVR (Advanced Security XVR) 21

Once the IP camera is added to the DVR, it will appear under the IP channel list. The green state means the camera has been added successfully. A grey color state means the IP camera needs attention, and when you click on the state icon, it will indicate if the error is caused by a wrong IP camera username/password or if it has a network issue.

To avoid network issues, make sure that your camera, DVR, and router are on the same IP address segment, e.g.

How to add IP Camera to Camius DVR (Advanced Security XVR) 22

Using the Camius XVR system, users can quickly and seamlessly integrate analog and IP cameras, providing greater flexibility in security camera selection. In addition, Camius Hybrid 8-Channel DVR recorders support up to 12 and 16-channel DVRs and up to 24 HD cameras, making a scalable solution for residential and commercial surveillance needs.

It is important to note that the cameras’ quality will significantly impact the system’s overall performance and effectiveness. Of course, high-quality cameras will provide better images, enabling more effective monitoring and surveillance, but also, Camius IP cameras offer intelligent motion, sound, and AI detection. Other manufacturers’ IP cameras are usually limited to basic video motion detection.

How to install a hard drive in a Camius DVR or NVR?

Installing a hard drive in a DVR (digital video recorder) or an NVR (network video recorder) (DVR NVR for short) is a relatively straightforward process. Still, it is essential to follow the steps carefully to ensure proper installation and prevent damage to the equipment. Here is a step-by-step guide on how to install a hard drive in your surveillance DVR or NVR recorder.

Camius network and hybrid digital video recorders accept 3.5″ and 2.5″ SSD internal hard drive disks. While 8 channel DVR and NVR recorders accept a single hard drive up to 10 TB in capacity, 16-channel DVR and NVR recording, along with 32-channel NVR will support a 14TB hard drive on each SATA port. 

Visit this link to see the tested and recommended hard drives, CLICK HERE

1 – Gather Tools and Equipment

You will need a Phillips head screwdriver, the hard drive you want to install, and any necessary screws (when you order a DVR or NVR from Camius without a pre-installed hard drive, the product box will include a set of screws for the hard drive disk installation).

2 – IMPORTANT: Make sure your DVR / NVR is unplugged and powered off

3 – Removing the Top Cover or the Video Recorder

Remove any screws from the Recorder’s top cover (chassis) using a Philips head screwdriver. Carefully remove the top chassis and set it aside (picture 1)

Picture 1 – 8 channel DVR

4 – Insert the Hard Drive

Place the hard drive into the hard drive bay, ensuring the drive is oriented correctly and appropriately seated.

5 – Connect the SATA Data and Power Cables

Connect the Data and Power cables to the two hard disk drives and place the hard disk drives on the video recorder’s case. The Data cable connects the hard drive to the DVR NVR’s motherboard. Locate the SATA port on the DVR’s motherboard and connect one end of the SATA cable to it. Then, connect the other end of the cable to the hard drive. The SATA Power cable provides power to the hard drive. Locate the SATA Power cable and connect one end to the hard drive and another to the Power Supply (pictures 2 and 3)

Picture 2 – Power and Data Cables on the Hard Drive

Picture 3 – Power and Data Cables on the DVR or NVR recorder’s board

Read Also : LaView NVR setup and user guide

6 – Secure the hard drive with srews

Carefully flip the video recorder case and secure the hard disk drives to the recorder with the four (4) screws if it is one SATA HDD (pictures 4 and 5) and eight (8) screws for the 2 SATA HDDs (picture 6)

Picture 4 – DVR with one internal SATA bay

Picture 5 – DVR with one internal SATA bay

Picture 6 – NVR with two internal SATA bays

7 – Return the DVR NVR top cover

Place the top cover on the DVR NVR and secure it with the screws (picture 7)

Picture 7 – DVR with one internal SATA bay

8 – Power on the DVR NVR

Power on the DVR NVR and allow it to boot up completely. If the hard drive was installed correctly and is in working condition, it should be recognized by the DVR and ready for use. Remember to format the hard drive (here is the guide on how to format the hard drive). Ensure that you use the power supply with the Camius video recorder.

IMPORTANT: Some users may find an issue when the hard drive is not recognized or not showing on the DVR. One of the primary reasons could be a wrong or defective recorder’s power supply.

That’s it! Your DVR NVR should now have a new hard drive installed, allowing it to store more video footage. Follow these steps carefully and seek additional assistance if you encounter any difficulties.

How to adjust my DVR NVR monitor resolution?

Camius video surveillance DVR NVR camera recorders have HDMI and VGA video output to live video feed on your monitor.

VGA output supports a max resolution of 1080p, while the HDMI video output 4K video resolution. So if the monitor you use with the Camius DVR or NVR recorder is capable of 4K and the camera, you can view live videos in 4K.

TRIVAULT4K2168R

How to adjust my DVR NVR monitor resolution? 19

IPVAULT1128PR

Two ways to adjust the DVR NVR monitor resolution

You can adjust the DVR NVR monitor resolution in the Wizard Setup mode or by navigating to Setup >> System >> General >> Output Configuration.

While in ‘Wizard Setup’ mode, choose an output resolution that matches your monitor. The DVR should adjust the output resolution automatically to match the best resolution of your monitor at the system startup. 

Please note that some legacy monitors could fail to communicate their acceptable resolution. In this case, please manually plug the video surveillance DVR into a newer monitor and change the resolution to the lowest setting, then save and plug the older monitor back to see if it’s supported.

After completing the Start Wizard, you can further adjust the Display Output Resolution using the following Menu Path: Setup – System – General – Output Configuration.

Select the output resolution suitable for your TV/Monitor. 1080P(1920 x 1080) will suit most monitors. If your DVR supports 4K output resolution, you can select either 2K (2560 x 1440) or 4K (3840 x 2160) to take advantage of the higher resolution that your 4K TV provides.

You can also adjust the size & position of the display screen to match your monitor/TV by using the ‘Scale and Offset’ feature; click the tab ‘Setup,’ which allows you to:

Click once or long-press the left button of your mouse on the arrow to adjust the size and position, or you can scroll the supplied USB mouse’s wheel to adjust. Click the right button of your mouse to exit, and click Apply to save your modifications.

How to reset the DVR and NVR video recorder to default factory settings

To reset DVR or NVR to default settings, navigate to the left bottom of the screen to the main menu. Select Setup >> System >> Maintenance >> Load Default

Here you can select the setting you wish to set to default. If you do not wish to reset the password, do not check the System boxes. Please note Load Default settings do not format your hard drive.

You’d need to enter the system password in the Authentication pop-up window (picture 1), which will lead to restarting your recorder (picture 2).

Picture 1

Picture 2

Navigate to Setup >> System >> Maintenance >> Reset Settings (Picture 3), where you can not select settings to reset so that it will reset your system completely, including the login credentials. You can choose ‘Format HDD‘ if you wish to format your hard drive, leading to erasing any recorded footage.

Picture 3

How to change your DVR and NVR password and add a user

You can update the ‘admin’ password by clicking the ‘User Edit’ button. You will need the admin’s current password to authenticate the new password.

Camius NVR and DVR recorder have an advanced user management feature to add multiple users to the system and control their permissions. System administration (admin) can add users, edit their permissions and delete them.

Navigate to the Main Menu in the bottom left corner, select System >> Multi-User (picture 1)

Picture 1

How to add a user to Camius NVR or DVR recorder 15

Click on the Edit icon in the User Edit column and select ‘Enable‘ in the User Enable tab. You can change the User Name or keep it as ‘user1‘. Create the new user password, confirm it, and click on the ‘Save‘ tab (pictures 2 and 3)

Picture 2

Picture 3

Then click the gear icon in the last Permission column to open the User Permission dialogue. Select (tick checkbox) the permissions you wish to grant to the new user. Click Save (picture 4)

Picture 4

How to troubleshoot if my DVR is not powering on?

If you’re having trouble with your DVR not powering on, here are some recommended troubleshooting steps:

Step 1 – Check the LEDs on the front panel, a steady green LED (PWR) means your DVR is powered on normally, and a blinking red LED (HDD) means ongoing recording on the hard drive. 

8 channel DVR

16 channel DVR

.

Step 2 – Check the sounds coming out of your recorder. A faint fan sound and a faint hard drive sound are normal, and a click sound when you plug in the DC connector and turn on the switch is typical.

Step 3 – If you have the green LED on but no output on the monitor, follow these steps:

Step 4 – Check the power outlet and the power supply unit of the DVR. If the power supply doesn’t have any LED indicator or the LED light is very faint and not bright green, and there is no fan sound coming from the DVR, the power supply may need replacement. If your DVR has running hardware warranty, please contact us. If the DVR is covered with warranty, you can order a new power supply on Camius site.

Why can’t I access my Camius IP cameras, DVR, and NVR on my Camius View app? 

If you can not access your Camius IP cameras, DVR (digital video recorder), or NVR (network video recorder) on the Camius View smartphone app, please check the below:

1 – Check if you are using the latest version of the Camius View app

On the App’s ‘Devices‘ page, make sure your recorder is added using P2P (ID) instead of IP (IP Address), and if in doubt, delete it and add it again. 

In the Media Port, make sure to enter the right port number:

2 – Make sure you’re connected to a reliable network on your phone 

3 – Check if your Camius IP camera or recorder is connected correctly to the LAN (Local network).

4 – Check for the IP address conflict

5 – Reset the Network settings of your Camius device

Navigate to Setup >> System >> Maintenance >> Load Default >> check the Network box and Apply

Camius Trivault DVR (local interface via HDMI)

Web browser view

6 – Check the Camius device network status 

Navigate to Setup >> System >> Information and check the Network Status if it shows ‘Connect success’.

If the above steps don’t help, submit a support request and include the device model number and the current ’Firmware/Software Version,’ which can be found using the Camius Device Config Tool

HDMI interface: DVR / NVR information is available under Setup >> System >> Information

Web browser view: information is available under Remote Setting >> System >> Information (web browser view)

7 – Wrong Password 

Before you add the Camius security device to the app, make sure to set a password  following the below setup guides:

We got you if you lost your IP camera or DVR NVR recorders password. Follow the below links on how to reset your device password:

You can not set a password on your Camius device using the Camius View app. 

Can I install an SSD hard drive instead of a regular one on my Camius DVR and NVR? 

The answer is ‘Yes.’

Camius recorders are compatible with 3.5″ and 2.5″ SATA (Serial Advanced Technology Attachment) and SSD hard drives (Sold-State Drive). 

Can I install an SSD hard drive instead of a regular one on my Camius DVR and NVR?  3

How to disable menu logout on the DVR and NVR?

Certain Camius device users prefer to remain logged into the menu of their DVR or NVR without re-entering their login credentials unless necessary. To achieve this, you can follow the steps outlined in this guide.

Move the mouse cursor to the bottom left, and click the main menu button: Setup >> System >> General >> Menu Timeouts >> Off >> Apply.

Optionally, you can set a different time for menu log-out as well. This guide applies to Camius NVR and DVR recorders.

It’s important to note that the web browsers will log you out of the session after some time (even if you set the number of sessions), as this function is implemented by the web browsers to enhance security.

To assist you in managing your login details more conveniently, consider using a password manager such as LastPass or similar services with browser extensions available. These services can help you securely store your login information (such as IP address, username, and password) and provide easy access even after your browser session expires.

You can also use VMS software on your desktop to add the DVR using a P2P ID and access the DVR’s ‘Remote Setting’ within the VMS; follow this guide on how to add the DVR to the software.

How to add IP cameras on a network that are not connected directly to the NVR’s PoE ports?

For the PoE-enabled NVR, connect Camius IP cameras via the internal NVR’s PoE ports and/or external LAN (WAN) port using the below-described model 2 or 3:
.

Camius PoE NVR is optimized for Camius PoE cameras making the whole setup process plug-and-play; the NVR assign a unique IP address to each Camius PoE camera and adds them automatically.

NOTE: Connecting multiple cameras via a switch or router to the PoE port is not recommended. One PoE port supports one IP camera.

The below steps are based on the NVR’s local interface via HDMI video output. Navigate the mouse to the screen’s left bottom corner and click on Setup, followed by Channel >> IP Channels.

In the below menu, you configure the connection of wired IP cameras.

Click Search to search for IP cameras from a local network, click Add to add an individual IP camera, and click Add All to add all IP cameras.

Below we will describe a few ways to add IP cameras from a local network using an external LAN (WAN) port.

IP channels menu description:

Select the suitable Protocol from the dropdown (Private is for Camius IP cameras), enter the IP camera(s) credentials (User Name and Password), and click Add. Green status indicates a successful connection; grey status could show a password or network error.

Green color State means the camera is added to the NVR

Grey color state icon means the IP camera failed to connect to the NVR. Click the gray icon to show the failure reason:

Option 1 – Adding IP Cameras to the NVR within the LAN (local area network )

If you want to connect to an IP camera from LAN (Local Area Network), please make sure your NVR is well-connected to the LAN and the IP camera you want to add is in the same network segment as your NVR.

If you want to add all channels manually, click the dropdown arrow next to Switch Mode and select “Manual.” 

If you want to add an individual channel manually, click the Edit Pencil-shaped icon in the Channel list, and then click the drop-down arrow next to Switch Mode to select “Manual” and click OK to save.

Option 2 – Adding an individual IP camera in the LAN (Local Network area)

STEP 1- Click the Search button; all available cameras in the LAN will be displayed, 

Optionally you click the Add plus-shaped green icon  in the IP channels list to add a camera to an individual channel. Click the Search button to show all available cameras in the LAN.

STEP 2 – Select the camera you want to add and then click Add button. Next, insert the user name and password of the camera and click Add button.

STEP 3 – You will see the added camera in the IP channels list

Option 3 – Add Multiple IP Cameras within the LAN

STEP 1- Click the Search button to display all available cameras in the LAN click Add All button, and the NVR will search & add all available cameras in the LAN.

STEP 2 – Select the cameras from the search result and click “Add.” You would need to input the username and password of the cameras. Please ensure all the cameras you want to add use the same username and password. Otherwise, the cameras with different user names and passwords cannot connect.

STEP 3 – The added cameras will show up in the channel list.

Option 4 – Add IP Cameras from another NVR in the same LAN (Local Area Network)

The NVR allows adding IP cameras from other Camius NVRs in the local network.

STEP 1 – Click the Search button to display all available devices in the LAN. There is an Edit icon (blue plus)  if the device is an NVR.

STEP 2 – Click the Edit icon (blue plus) and select the camera channels one by one or check the box to select all cameras. Click the icon X to go back to the Search list.

STEP 3 – Select the NVR in the search list and click the Add button.

STEP 4 – Input the Username and Password of the NVR and then click Add button

STEP 5 – The added cameras will be displayed in the channel list

Option 5 – Add IP Cameras from the Internet

If your NVR is connected to the Internet, you can add cameras with a WAN (Wide Area Network) IP address.

STEP 1 – Click Add button on the search page.

STEP 2 – Input the IP address or Domain name, Alias (name of the IP camera), Port, Protocol (choose the protocol of the IP camera from the dropdown menu: Private, Onvif or RTSP), User Name & Password of the IP camera.Tap the Add button to add the camera.

To avoid network issues, make sure that your camera, NVR, and router are on the same IP address segment, e.g.

.

How to configure Camius NVR using a web browser?

To quickly find the Camius DVR (digital video recorder) or NVR (network video recorder) IP address, visit camius.com/support to download and install the Camius Device Config Tool.

Web browser access

Click on the Camius NVR or DVR’s local IP or type it into your browser’s address bar. The latest Camius surveillance security camera recorders work with multiple web browsers, including Edge, Google Chrome, Mozilla Firefox, Edge, and Safari, and include the following models:

Use your admin username and DVR or NVR password to log in. Your recorder’s Configuration is under Remote Settings.

You can check the ‘Web Compatibility Mode‘ in the Camius NVR/DVR and even IP camera settings (this can be done from the Camius recorder’s local user interface (Via HDMI/VGA) and in the web browser viewer.

The below picture is based on the IPVAULT1128PR’s web browser view

Accessing web client through VMS software

For certain Camius DVRs, NVRs, and IP camera models, we recommend installing the VMS Software on your Windows or Mac computer to access the device’s remote settings since the VMS software has a built-in web client using the P2P ID. Here is the link to the guide on how to add the device to the VMS software. This applies to Camius IPVAULT2320P16N, SCOUT20PTZ, GUARDMA

.

.

Production Introduction

The DVR series is a HD surveillance product that designed for security field. It uses an embedded LINUX operating system to ensure stable system performance. It adopts the standard H.265 video compression algorithm and a unique spatial-temporal filtering algorithm to achieve high-quality, low-bitrate synchronous audio and video and 24/7 video recording. With TCP/IP network technologies, it

has powerful network data transmission and remote control capabilities.

The DVR can be used locally or online applied as a part of a safety surveillance network. With professional network video surveillance software, it fully demonstrates its strong networking and telecommunication capabilities.

This DVR can be applied to security measures in various fields and departments such as banking, telecommunications, electric power system, judiciary system, transportation, smart communities, factories, warehouses and water facilities.

.

Unboxing and Initial Setup

When you receive this product, please confirm that it matches the model you ordered and carefully inspect the device for any obvious damage. After opening the casing, check whether the data cable, power cable, and other connections inside the device are firmly connected to the main board.

Please protect the labels attached to the bottom or back panel, which is very important to our after-sales service work. When contacting our company for after-sales service, you will need to provide the model and serial number on the order label.

1.2Gallery

.

Power Indicator

Network Indicator

⑨  ⑩ ⑪

Hard drive

.

.

LAN

.

.

.

.

HD Digital Video Recorder

.

.

.

.

Video Input

.

⑧

Audio Output

⑫ USB2.0

VGA  Ethernet Port

.

.

Audio Input

HDMI

USB2.0 Power Port

.

NOTE: The picture shown is for reference only. Actual appearance is subject to the model you purchased.

How to set up Zosi XVR System

Read More : How to Connect Zosi wifi cameras to nvr

Suggestion: Please test the product before installation to ensure it is functioning properly.

Ⓒ Connect the camera to the DVR via a BNC cable.

Ⓒ Connect the DVR to the monitor via an HDMI or VGA cable.

Ⓒ Connect the DVR to the router via a network cable.

Ⓐ Connect the mouse to the USB port of the DVR.

Ⓒ Power on the DVR by connecting it to a power source.

⑥ The monitor will display the real-time monitoring image from the camera.

.

Via Smartphone

Search “ZOSI” in App Store, or use a browser to scan the QR code below to download and install the App, and follow the on-screen instructions to complete the initial setup.

.

App video operation link

.

Via PC

Download: https://www.zositech.com/app/

.

Basic Operation

After connecting the power supply, the power indicator light will turn on, and the device will start up. At this time, you will hear a “beep” from the buzzer. By default, the system is in multi-screen mode.

Mouse Use:

Left-click:

Double-click a single-channel to make it full screen, and double-click again to return to the multi-channel display.

Click once to open a menu option. Right-click：

Click once to exit the current menu or return to the previous menu option.

.

Left-click  Right-click

.

.

.

.

.

After the device is powered on normally, you need to log in to the system before operating it. The system will provide corresponding functions according to the permissions of the logged-in user.

The default for the device is “admin” and the default password is blank. You can log in to the system directly the first time after powering on.

.

....After entering the preview page, double-click the left mouse button to switch between single or multiple display. On each preview screen, the date, time, and channel name can be displayed, and each screen display the recording and alarm status of the monitoring channel.

.

.

Motion Detection Triggered Motion+PIR Detection Triggered

.

Human-Figure Detection Triggered

PIR Detection Triggered Vehicle Detection Triggered

In preview mode, click the right mouse button to bring up the quick menu, and click the right mouse button again to exit the quick menu.

1.4.1Start Scan

Start Scan refers to the system automatically displaying each live video in sequence according to the order of the devices in channel lists. The jump button is available only when the user selects the channel in [Main Menu]>[Setup]>[Live], and when not all channels can be displayed completely in the current preview mode.

Adjust image settings for all channels: Brightness, Contrast, Saturation and Hue.

Zoomed in digitally up to 4X or 8X of single channel.

Set the audio settings for each channel to enable, disable, or mute audio, and adjust the volume. When [Auto] is selected, the audio will be enabled automatically when switching to the full-screen display.

.

Control the RS485 devices of all channels. Set the address, baud rate, protocol, preset points, patrol routes, tracks, etc. of the RS485 device in [Main Menu] > [Setup]

> [PTZ ]

Note: Due to differences in product design, some devices may not support RS485 interface.

Right-click and select Playback to choose between Video Playback/Quick Playback, Video Playback: Search for the video you want by time or event, then click Play.

Quick Playback: Quickly playback the first 30 minutes of video.

.

.

Play/Pause

Fast  Rewind Forward

Multi-screen display

Previous Record  Next Record

Previous Video: Go to the previous recorded event.

Next Video: Go to the next recorded event.

Fast Forward: The video can be played at different speeds, from 1/4x to 16x. Rewind: The video can be played at 1x, 8x, 16x, and 32x speed for rewind viewing. Display Mode: Both single-screen and multi-screen display modes are available. You can choose the number of screens you want to play simultaneously. Channels without recordings will display a black screen during playback.

.

Main Menu

.

Set functional parameters of the device, including: Basic Configuration, Live Configuration, Recording Configuration, Recording Schedule, Alarm Configuration, Network Configuration, User Management, PTZ Configuration, Advanced Configuration.

.

Basic configuration contains 3 sub-menus: System, Date & Time, and DST

[System Type]: The name of the system displayed on the client

[Model Number]: Used for controlling multiple DVRs with one remote control [Video Format]: Supports PAL and NTSC video format.

[Password Check]: Checking this option means that users must enter a username

and password in the system settings and have the corresponding permissions to perform certain operations.

[Show System Time]: Choose whether to display the time on the scene.

[Max Online Users]: Set the number of network users who can access the device. [Video Output]: Users can select output resolutions 1024×768, 1280×1024, 1920×1080, etc.

[Logout After (Minutes)]: The system automatically logs out after a set time of inactivity. [Startup Wizard]: Whether to display the wizard on startup.

.

Set the date format, time format, time zone, and manually adjust the system time.

NOTE: The system default time zone of the system is GMT. You can select

[Time Synchronization] to correct the time. The network time server can also be set.

Set the start and end times of daylight saving time through the week or date.

.

Live configuration contains 3 sub-menus: Live, Main Monitor, and Video Video Masking.

.

[Camera Name] Click on the camera name, and a software keyboard will pop up. Users can modify the camera name as needed.

Click on the Shift key to switch input method.

[Colour] Users can adjust the brightness, hue, saturation, and contrast of the channel.

.

[Interval] The time interval for switching from one channel to another in sequence during channel rotation.

.

Users can mask certain areas in the scene, max 4 areas.

[Setting] Enter the live view, hold down the left mouse button, drag the mouse to set the blocked area, click [Apply] to save the setting.

Double-click the area that needs to be deleted, and the area will turn black. Right-click

to exit, and then click[Apply] to delete the blocked area.

.

Recording configuration contains 5 sub-menus: Enable, Record Bitrate, Stamp, Recycle Record, and Snap

.

Enable/disable recording and audio functions for a specific channel, or set all channels to default enable.

[Resolution] The recording resolution for each channel [FPS] Selection range: 1-30 (NTSC) 1-25 (PAL)

[Encode] The camera’s encoding type, support VBR and CBR

[Quality] The higher the quality, the clearer the video image. Options include Lowest,

Lower, Low, Medium, Higher, and Highest [Max Bitrate] Range: 256kbps ~ 2048kbps

[Adjust] The video format, including CVBS, AHD, CVI, and TVI

Note：These functions are not optional

[Camera Name] Select whether to display the camera name or not [Time Stamp] Select whether to display time on this channel or not

[Position] Click this button and users can use the mouse to drag the camera name and timestamp to any position on the live screen.

4.Recycle Record

.

When selected, the DVR will automatically overwrite the oldest files and continue recording when the hard disk is full. If not selected, the DVR will stop recording when the hard disk is full and prompt “Insufficient remaining space” on the screen.

Recording schedule contains 6 submenus: Schedule, Motion, Sensor, PIR, Vehicle , and Human.

[Copy] Apply the recording schedule of a certain channel to other channels or all channels.

Select the channel, double-click the left mouse button, and edit the weekly plan.

[Add] Add a recording schedule for a certain day [Delete] Delete the selected schedule

[Copy] Copy the schedule of a specified date to other dates. Double-click the left mouse button to customize the effective recording mode time for each day of the week.

The setting is the same as that of scheduled recording, please refer to scheduled recording setting.

NOTE: The default schedule for motion detection recording is all selected.

The setting is the same as that of scheduled recording, please refer to scheduled recording setting.

NOTE: The default schedule for sensor alarm recording is all selected.

The setting is the same as that of scheduled recording, please refer to scheduled recording setting.

NOTE: The default schedule for PIR detection alarm recording is all selected.

The setting is the same as that of scheduled recording, please refer to scheduled recording setting.

NOTE: The default schedule for vehicle detection recording is all selected.

The setting is the same as that of scheduled recording, please refer to scheduled recording setting.

NOTE: The default schedule for human detection recording is all selected.

The Alarm configuration contains 7 sub-menus: Sensor Alarm, Motion Detection, Video Loss, PIR Detection, Human Detection, Vehicle Detection, and Other Alarms.

.

NOTE: Some products may cancel sensor alarm recording due to product differences.

1-1. Basic Configuration

.

[Enable] Enable the sensor alarm function for the corresponding channel [Type] Select the alarm type: Normally open or Normally closed

[Name] Set the name of the sensor

1-2. Alarm Handling

[Holding Time] Select the alarm delay time, with options of 5s, 10s, 20s, 30s, 60s, 120s, Always

[Trigger] Click to set alarm configuration, trigger recording, PTZ linkage, etc. [Buzzer] When selected, the buzzer will sound when an alarm triggered

[Show Full Screen] When there is an alarm trigger, the alarm will pop up in full- screen display

[To Alarm Out] Select to trigger the alarm output on a specified channel

[Email] When an alarm is triggered, the system will send relevant information to the user’s designated email, such as the alarm event, snapshot, device name, device number, etc.

[Snap] When an alarm is triggered, the system will automatically capture and save images of the selected channel

[To Record] Select the channel to trigger recording

[To PTZ] To set the action type and serial number of the linkage

1-3. Schedule

The schedule settings for sensor alarm are the same as for scheduled recording. For specific setting steps, please refer to 4.2.4 [Recording Schedule] -[Schedule] NOTE: The default schedule for sensor alarm is Select All

Motion Detection contains 2 sub-menus: Motion and Schedule.

2-1. Motion Detection

By analyzing the video image, when the system detects motion signals that reach the preset sensitivity, it will trigger motion detection alarms and activate the linkage function to push the alarm information to the App or email.

[Enable] After selected, the Motion detection function of the corresponding channel is turned on, and it is enabled by default

[Holding Time] Select the alarm delay time for the channel, which can be set to 5s, 10s, 20s, 30s, 60s, 120s, or Always on.

[Push Time] Set the time interval for pushing alarm notification to the mobile App, which can be set to 1min, 2min, 3min, 5min, 8min, or 10min.

[Trigger] The setting is the same as that of sensor alarm, please refer to 4.2.5 Alarm Configuration – Sensor

[Area] In this interface, users can drag the scroll bar to adjust the sensitivity value (1-8), the default value is 6, the smaller the value, the higher the sensitivity. Because the sensitivity is affected by factors such as color and time (day or night), users should adjust the value according to the actual situation.

Click or drag the mouse to select or erase the detection area.

Click the star icon to set the entire field of view as a sensitive area

.

Click the trash icon to clear the current detection area

Click to save settings

.

Click to log out

The sensitivity index ranges from 1 to 8. The default sensitivity is 6. The lower the value, the more sensitive. The higher the value, the less sensitive.

Note: It is best not to have flags,trees or other objects that are easy to flutter in the wind in the grid for motion detection to avoid false alarms.

2-2. Schedule

The setting of the motion detection schedule is the same as that of the scheduled recording. Please refer to 4.2.4 [Recording Schedule]-[Schedule] for specific

setup steps. This function controls the effective time of the motion detection feature. Note: The default schedule for motion detection is to Select All.

This function needs to be used with a camera with PIR (Passive Infrared) capability. After PIR detection is set, the DVR will only record when it detects human life, and push the alarm notifications to the App or mailbox.

.

[Enable] After selected, the PIR detection function of the corresponding channel is turned on, and it is enabled by default

[Holding Time] Select the alarm delay time for the channel. Options: 5s, 10s, 20s, 30s, 60s, 120s, Always

[Push Time] Set the time interval for alarm notifications to be sent to the App.

Options: 1min, 2min, 3min, 5min, 8min, 10min

[Trigger] The setup method is the same as sensor alarm. Please refer to 4.2.5 Alarm Configuration – Sensor

[Schedule] PIR detection schedule setting is the same as Schedule Recording. For detailed instructions, please refer to 4.2.4 Recording Schedule. This feature controls the effective time of PIR detection

By analyzing the video image, the system activates human detection alarm when

it detects human figure. It also triggers linkage functions and sends alarm notifications to the App or mailbox.

.

[Enable] After selected, the human detection function of the corresponding channel is turned on, and it is enabled by default

[Holding Time] Select the alarm delay time for the channel. Options: 5s, 10s, 20s, 30s, 60s, 120s, Always

[Push Time] Choose the time interval for alarm notifications sent to the App. O ptions: 1min, 2min, 3min, 5min, 8min, 10min

[Trigger] The setup process is the same as sensor alarm configuration, please refer to

[Schedule】The schedule settings for human detection alarm are the same as Schedule Recording. For detailed instructions, please refer to 4.2.4 Recording Schedule. This feature controls the effective time of human detection

By analyzing the video image, the system detects vehicle contours and triggers motion detection alarms. It also activates the linkage function to send alarm notifications to the App or mailbox.

[Enable] After selected, the vehicle detection function of the corresponding channel is turned on, and it is enabled by default

[Holding Time] Select the alarm delay time for the channel. Options: 5s, 10s, 20s, 30s, 60s, 120s, and Always

[Push Time] Set the time interval for sending alarm notifications to the App. Options: 1min, 2min, 3min, 5min, 8min, and 10min

[Trigger] The setup process is the same as for sensor alarm configuration. Please refer to 4.2.5 Alarm Configuration – Sensor

[Schedule] The schedule settings for human detection alarm are the same as Schedule Recording. For detailed instructions, please refer to 4.2.4 Recording Schedule. This function controls the effective time of vehicle detection

The handling of video loss alarms is the same as for sensor alarms. For detailed instructions, please refer to 4.2.5 Alarm Configuration – Sensor

[Alarm Types] Including Disk Full, IP Conflict, Disconnect, Disk Shortage Alarm,

Disk lost

[Buzzer] When an alarm occurs, the device emits two long beeps.

[Email] When an alarm is triggered, the system sends relevant information such as the alarm event, snapshots, device name, and device ID to the user’s specified email address.

[To Alarm Out] After selected, and an alarm will be triggered on the specified alarm output.

[Disk Shortage Alarm] When the remaining capacity of the hard disk reaches the set value, an alarm will be triggered.

Network Configuration contains 4 sub-menus: Network, Email, WIFI Setup, DDNS

.

[HTTP Port] 80 by default [Server Port] 5000 by default

[Mobile Port] 5001 by default [Obtain an IP Address Automatically] Enable automatic IP address acquisition

[IP Address] Set the IP address of the device [Subnet Mask] Set the subnet mask of the device

[Gateway] Set the default gateway of the device

[Preferred DNS Server] This address is provided by your internet service provider (ISP). It must be filled in when using mobile monitoring.

[Alternate DNS Server] This address is provided by your internet service provider (ISP).

[PPPOE] Enable this option to establish a network connection using PPPoE. The connected IP address can be checked in[Main Menu]- [Information]- [Network] [User Name] Enter ISP (provided by Internet Service Provider)

[Password] The password set

[Test] Test whether the input IP address or PPPoE information is valid

.

[SMTP Server] Mail server address, which can be an IP address or a domain name

(if it is a domain name, ensure that DNS is correctly configured for proper resolution).

For example: smtp.gmail.com

[Port] Mail server port number, the default port is 465

[SSL Check] Enable SSL (Secure Socket Layer) protocol for secure login [Send Address] The email address of the mail server

[Password] The password for the sender’s email address